summaryrefslogtreecommitdiff
path: root/arch/arm/cpu/armv7
Commit message (Collapse)AuthorAgeLines
* Exynos: Fix L2 cache timings on Exynos5420 and Exynos5800Doug Anderson2015-02-28-93/+77
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | It was found that the L2 cache timings that we had before could cause freezes and hangs. We should make things more robust with better timings. Currently the production ChromeOS kernel applies these timings, but it's nice to fixup firmware too (and upstream probably won't take our kernel hacks). This also provides a big cleanup of the L2 cache init code avoiding some duplication. The way things used to work: * low_power_start() was installed by the SPL (both at boot and resume time) and left resident in iRAM for the kernel to use when bringing up additional CPUs. It used configure_l2_ctlr() and configure_l2_actlr() when it detected it was on an A15. This was needed (despite the L2 cache registers being shared among all A15s) because we might have been the first man in after the whole A15 cluster was shutdown. * secondary_cores_configure() was called on at boot time and at resume time. Strangely this called configure_l2_ctlr() but not configure_l2_actlr() which was almost certainly wrong. Given that we'll call both (see next bullet) later in the boot process it didn't matter for normal boot, but I guess this is how L2 cache settings got set on 5420/5800 (but not 5250?) at resume time. * exynos5_set_l2cache_params() was called as part of cache enablement. This should happen at boot time (normally in the SPL except for USB boot where it happens in main U-Boot). Note that the old code wasn't setting ECC/parity in the cache enablement code but we happened to get it anyway because we'd call secondary_cores_configure() at boot time. For resume time we'd get it anyway when the 2nd A15 core came up. Let's make this a whole lot simpler. Now we always set these parameters in the same place for all boots and use the same code for setting up secondary CPUs. Intended net effects of this change (other than cleanup): * Timings go from before: data: 0 cycle setup, 3 cycles (0x2) latency tag: 0 cycle setup, 3 cycles (0x2) latency after: data: 1 cycle setup, 4 cycles (0x3) latency tag: 1 cycle setup, 4 cycles (0x3) latency * L2ACTLR is properly initted on 5420/5800 in all cases. One note is that we're still relying on luck to keep low_power_start() working. The compiler is being nice and not storing anything on the stack. Another note is that on its own this patch won't help to fix cache settings in an RW U-Boot update where we still have the RO SPL. The plan for that is: * Have RW U-Boot re-init the cache right before calling the kernel (after it has turned the L2 cache off). This is why the functions are in a header file instead of lowlevel_init.c. * Have the kernel save the L2 cache settings of the boot CPU and apply them to all other CPUs. We get a little lucky here because the old code was using "|=" to modify the registers and all of the bits that it's setting are also present in the new settings (!). That means that when the 2nd CPU in the A15 cluster comes up it doesn't actually mess up the settings of the 1st CPU in the A15 cluster. An alternative option is to have the kernel write its own low_power_start() code. Signed-off-by: Doug Anderson <dianders@chromium.org> Signed-off-by: Akshay Saraswat <akshay.s@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
* Exynos542x: Make A7s boot with thumb-mode U-Boot on warm resetAkshay Saraswat2015-02-28-1/+1
| | | | | | | | | | | | | | | | | | | | On warm reset, all cores jump to the low_power_start function because iRAM data is retained and because while executing iROM code all cores find the jump flag 0x02020028 set. In low_power_start, cores check the reset status and if true they clear the jump flag and jump back to 0x0. The A7 cores do jump to 0x0 but consider following instructions as a Thumb instructions which in turn makes them loop inside the iROM code instead of jumping to power_down_core. This issue is fixed by replacing the "mov pc" instruction with a "bx" instruction which switches state along with the jump to make the execution unit consider the branch target as an ARM instruction. Signed-off-by: Akshay Saraswat <akshay.s@samsung.com> Reviewed-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
* Exynos542x: Fix secondary core booting for thumbAkshay Saraswat2015-02-28-1/+1
| | | | | | | | | | | | | | | | | | | | When compiled SPL for Thumb secondary cores failed to boot at the kernel boot up. Only one core came up out of 4. This was happening because the code relocated to the address 0x02073000 by the primary core was an ARM asm code which was executed by the secondary cores as if it was a thumb code. This patch fixes the issue of secondary cores considering relocated code as Thumb instructions and not ARM instructions by jumping to the relocated with the help of "bx" ARM instruction. "bx" instruction changes the 5th bit of CPSR which allows execution unit to consider the following instructions as ARM instructions. Signed-off-by: Akshay Saraswat <akshay.s@samsung.com> Reviewed-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
* Exynos542x: add L2 control register configurationAkshay Saraswat2015-02-28-13/+64
| | | | | | | | | | | | | | | This patch does 3 things: 1. Enables ECC by setting 21st bit of L2CTLR. 2. Restore data and tag RAM latencies to 3 cycles because iROM sets 0x3000400 L2CTLR value during switching. 3. Disable clean/evict push to external by setting 3rd bit of L2ACTLR. We need to restore this here due to switching. Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com> Signed-off-by: Akshay Saraswat <akshay.s@samsung.com> Reviewed-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
* Exynos542x: cache: Disable clean/evict push to externalAkshay Saraswat2015-02-28-1/+17
| | | | | | | | | | | | | L2 Auxiliary Control Register provides configuration and control options for the L2 memory system. Bit 3 of L2ACTLR stands for clean/evict push to external. Setting bit 3 disables clean/evict which is what this patch intends to do. Signed-off-by: Akshay Saraswat <akshay.s@samsung.com> Reviewed-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
* Exynos542x: Add workaround for exynos iROM errataAkshay Saraswat2015-02-28-16/+200
| | | | | | | | | | | | | | | | | | | | | | | | | | iROM logic provides undesired jump address for CPU2. This patch adds a programmable susbstitute for a part of iROM logic which wakes up cores and provides jump addresses. This patch creates a logic to make all secondary cores jump to a particular address which evades the possibility of CPU2 jumping to wrong address and create undesired results. Logic of the workaround: Step-1: iROM code checks value at address 0x2020028. Step-2: If value is 0xc9cfcfcf, it jumps to the address (0x202000+CPUid*4), else, it continues executing normally. Step-3: Primary core puts secondary cores in WFE and store 0xc9cfcfcf in 0x2020028 and jump address (pointer to function low_power_start) in (0x202000+CPUid*4). Step-4: When secondary cores recieve event signal they jump to this address and continue execution. Signed-off-by: Kimoon Kim <kimoon.kim@samsung.com> Signed-off-by: Akshay Saraswat <akshay.s@samsung.com> Reviewed-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
* Exynos542x: CPU: Power down all secondary coresAkshay Saraswat2015-02-28-0/+72
| | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds code to shutdown secondary cores. When U-boot comes up, all secondary cores appear powered on, which is undesirable and causes side effects while initializing these cores in kernel. Secondary core power down happens in following steps: Step-1: After Exynos power-on, primary core starts executing first. Step-2: In iROM code every core has to check 2 flags i.e. addresses 0x02020028 & 0x02020004. Step-3: Initially 0x02020028 is 0 for all cores and 0x02020004 has a jump address for primary core and 0 for all secondary cores. Step-4: Therefore, primary core follows normal iROM execution and jumps to BL1 eventually, whereas all secondary cores enter WFE. Step-5: When primary core comes into function secondary_cores_configure, it puts pointer to function power_down_core into 0x02020004 and provides DSB and SEV for all cores so that they may come out of WFE and jump to power_down_core function. Step-6: And ultimately because of power_down_core all secondary cores shut-down. Signed-off-by: Kimoon Kim <kimoon.kim@samsung.com> Signed-off-by: Akshay Saraswat <akshay.s@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
* Merge branch 'master' of git://git.denx.de/u-boot-fsl-qoriqTom Rini2015-02-25-10/+221
|\
| * arm: ls102xa: workaround for cache coherency problemchenhui zhao2015-02-24-0/+28
| | | | | | | | | | | | | | | | | | | | The RCPM FSM may not be reset after power-on, for example, in the cases of cold boot and wakeup from deep sleep. It causes cache coherency problem and may block deep sleep. Therefore, reset them if they are not be reset. Signed-off-by: Chenhui Zhao <chenhui.zhao@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
| * arm/ls102xa: create TLB to map PCIe regionMinghuan Lian2015-02-24-10/+193
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | LS1021A's PCIe1 region begins 0x40_00000000; PCIe2 begins 0x48_00000000. In order to access PCIe device, we must create TLB to map the 40bit physical address to 32bit virtual address. This patch will enable MMU after DDR is available and creates MMU table in DRAM to map all 4G space; then, re-use the reserved space to map PCIe region. The following the mapping layout. VA mapping: ------- <---- 0GB | | | | |-------| <---- 0x24000000 |///////| ===> 192MB VA map for PCIe1 with offset 0x40_0000_0000 |-------| <---- 0x300000000 | | |-------| <---- 0x34000000 |///////| ===> 192MB VA map for PCIe2 with offset 0x48_0000_0000 |-------| <---- 0x40000000 | | |-------| <---- 0x80000000 DDR0 space start |\\\\\\\| |\\\\\\\| ===> 2GB VA map for 2GB DDR0 Memory space |\\\\\\\| ------- <---- 4GB DDR0 space end Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* | kconfig: remove unneeded dependency on !SPL_BUILDMasahiro Yamada2015-02-24-22/+21
| | | | | | | | | | | | | | Now CONFIG_SPL_BUILD is not defined in Kconfig, so "!depends on SPL_BUILD" and "if !SPL_BUILD" are redundant. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
* | kconfig: switch to single .config configurationMasahiro Yamada2015-02-24-1/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When Kconfig for U-boot was examined, one of the biggest issues was how to support multiple images (Normal, SPL, TPL). There were actually two options, "single .config" and "multiple .config". After some discussions and thought experiments, I chose the latter, i.e. to create ".config", "spl/.config", "tpl/.config" for Normal, SPL, TPL, respectively. It is true that the "multiple .config" strategy provided us the maximum flexibility and helped to avoid duplicating CONFIGs among Normal, SPL, TPL, but I have noticed some fatal problems: [1] It is impossible to share CONFIG options across the images. If you change the configuration of Main image, you often have to adjust some SPL configurations correspondingly. Currently, we cannot handle the dependencies between them. It means one of the biggest advantages of Kconfig is lost. [2] It is too painful to change both ".config" and "spl/.config". Sunxi guys started to work around this problem by creating a new configuration target. Commit cbdd9a9737cc (sunxi: kconfig: Add %_felconfig rule to enable FEL build of sunxi platforms.) added "make *_felconfig" to enable CONFIG_SPL_FEL on both images. Changing the configuration of multiple images in one command is a generic demand. The current implementation cannot propose any good solution about this. [3] Kconfig files are getting ugly and difficult to understand. Commit b724bd7d6349 (dm: Kconfig: Move CONFIG_SYS_MALLOC_F_LEN to Kconfig) has sprinkled "if !SPL_BUILD" over the Kconfig files. [4] The build system got more complicated than it should be. To adjust Linux-originated Kconfig to U-Boot, the helper script "scripts/multiconfig.sh" was introduced. Writing a complicated text processor is a shell script sometimes caused problems. Now I believe the "single .config" will serve us better. With it, all the problems above would go away. Instead, we will have to add some CONFIG_SPL_* (and CONFIG_TPL_*) options such as CONFIG_SPL_DM, but we will not have much. Anyway, this is what we do now in scripts/Makefile.spl. I admit my mistake with my apology and this commit switches to the single .config configuration. It is not so difficult to do that: - Remove unnecessary processings from scripts/multiconfig.sh This file will remain for a while to support the current defconfig format. It will be removed after more cleanups are done. - Adjust some makefiles and Kconfigs - Add some entries to include/config_uncmd_spl.h and the new file scripts/Makefile.uncmd_spl. Some CONFIG options that are not supported on SPL must be disabled because one .config is shared between SPL and U-Boot proper going forward. I know this is not a beautiful solution and I think we can do better, but let's see how much we will have to describe them. - update doc/README.kconfig More cleaning up patches will follow this. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Reviewed-by: Simon Glass <sjg@chromium.org>
* | ARM: UniPhier: set CONFIG_SYS_MALLOC_F to the global default valueMasahiro Yamada2015-02-24-1/+1
|/ | | | | | | | | It is true that malloc is necessary for Driver Model before relocation, but there is no good reason to reserve the malloc space more than enough. The default value 0x400 works well. Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Reviewed-by: Simon Glass <sjg@chromium.org>
* bcm2836 SoC support (used in Raspberry Pi 2 model B)Stephen Warren2015-02-21-0/+14
| | | | | | | | | | | | The bcm2835 and bcm2836 are essentially identical, except: - The CPU is an ARM1176 v.s. a quad-core Cortex-A7. - The physical address of many IO controllers has moved. Rather than introducing a whole new bcm2836 value for $(SOC) or $(ARCH), update the existing bcm2835 code to handle the minor differences, and plumb it into the ARMv7 CPU architecture. Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
* ARM: keystone: move SoC sources to mach-keystoneMasahiro Yamada2015-02-21-2190/+0
| | | | | | | | Move arch/arm/cpu/armv7/keystone/* -> arch/arm/mach-keystone/* Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Tom Rini <trini@ti.com>
* ARM: highbank: move SoC sources to mach-highbankMasahiro Yamada2015-02-21-55/+0
| | | | | | | | Move arch/arm/cpu/armv7/highbank/* -> arch/arm/mach-highbank/* Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Cc: Rob Herring <robh@kernel.org>
* ARM: tegra: collect SoC sources into mach-tegraMasahiro Yamada2015-02-21-736/+0
| | | | | | | | | | | | | | | | | | | | | | | | | This commit moves files as follows: arch/arm/cpu/arm720t/tegra20/* -> arch/arm/mach-tegra/tegra20/* arch/arm/cpu/arm720t/tegra30/* -> arch/arm/mach-tegra/tegra30/* arch/arm/cpu/arm720t/tegra114/* -> arch/arm/mach-tegra/tegra114/* arch/arm/cpu/arm720t/tegra124* -> arch/arm/mach-tegra/tegra124/* arch/arm/cpu/arm720t/tegra-common/* -> arch/arm/mach-tegra/* arch/arm/cpu/armv7/tegra20/* -> arch/arm/mach-tegra/tegra20/* arch/arm/cpu/armv7/tegra30/* -> arch/arm/mach-tegra/tegra30/* arch/arm/cpu/armv7/tegra114/* -> arch/arm/mach-tegra/tegra114/* arch/arm/cpu/armv7/tegra124/* -> arch/arm/mach-tegra/tegra124/* arch/arm/cpu/armv7/tegra-common/* -> arch/arm/mach-tegra/* arch/arm/cpu/tegra20-common/* -> arch/arm/mach-tegra/tegra20/* arch/arm/cpu/tegra30-common/* -> arch/arm/mach-tegra/tegra30/* arch/arm/cpu/tegra114-common/* -> arch/arm/mach-tegra/tegra114/* arch/arm/cpu/tegra124-common/* -> arch/arm/mach-tegra/tegra124/* arch/arm/cpu/tegra-common/* -> arch/arm/mach-tegra/* Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Tested-by: Simon Glass <sjg@chromium.org> [ on nyan-big ] Cc: Stephen Warren <swarren@nvidia.com> Cc: Tom Warren <twarren@nvidia.com>
* ARM: at91: collect SoC sources into mach-at91Masahiro Yamada2015-02-21-742/+0
| | | | | | | | | | | | This commit moves source files as follows: arch/arm/cpu/arm920t/at91/* -> arch/arm/mach-at91/arm920t/* arch/arm/cpu/arm926ejs/at91/* -> arch/arm/mach-at91/arm926ejs/* arch/arm/cpu/armv7/at91/* -> arch/arm/mach-at91/armv7/* arch/arm/cpu/at91-common/* -> arch/arm/mach-at91/* Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Acked-by: Andreas Bießmann <andreas.devel@googlemail.co>
* Merge branch 'master' of http://git.denx.de/u-boot-sunxiTom Rini2015-02-17-93/+133
|\
| * sunxi: Support the FEL boot mode in the regular u-boot buildSiarhei Siamashka2015-02-16-10/+47
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | So that the CONFIG_SPL_FEL option is not needed anymore. And the regular SPL binary, generated by the default u-boot build, is now also bootable over USB in the FEL mode. The SPL still can boot from the SD card too. A bunch of system registers need to be saved/restored in order to ensure that the IRQ handler still works in the BROM FEL code after getting control back from the SPL. This is done in the sunxi code instead of abusing ifdefs in 'start.S'. The decision whether to load the main u-boot binary from the SD card or return to the FEL code in the BROM is done at runtime. Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> [hdegoede@redhat.com: Since we now restore various regs before returning to the FEL BROM code we can drop the sunxi specific #ifdefs in start.S] Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
| * sunxi: Normalise FEL supportSimon Glass2015-02-16-88/+51
| | | | | | | | | | | | | | | | | | | | | | | | Make sunxi's FEL code fit with the normal U-Boot boot sequence instead of creating its own. There are some #ifdefs required in start.S. Future work will hopefully remove these. This series is available at u-boot-dm, branch sunxi-working. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
| * arm: Allow lr to be saved by board codeSimon Glass2015-02-16-5/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The link register value can be required on some boards (e.g. FEL mode on sunxi) so use a branch instruction to jump to save_boot_params() instead of a branch link. This requires a branch back to save_boot_params_ret so adjust the users to deal with this. For exynos just drop the function since it doesn't do anything. Signed-off-by: Simon Glass <sjg@chromium.org> Acked-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
| * sunxi: dram: Un-inline dram helper functionsHans de Goede2015-02-16-0/+38
| | | | | | | | | | | | | | | | | | Move the dram helper functions to a separate C file, rather then having them as inline helpers in dram.h. This saves 144 bytes in the .text segment for sun6i builds. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Simon Glass <sjg@chromium.org>
* | keystone2: ddr3: eliminate using global ddr3_size variableVitaly Andrianov2015-02-16-4/+1
| | | | | | | | | | | | | | | | | | | | | | | | KS2 ddr3 initialization uses ddr3_size global variable before u-boot relocation. Even if the variable is not being used after relocation, writing to it corrupts relocation table. This patch removes the global ddr3_size variable and uses local one instead. Signed-off-by: Vitaly Andrianov <vitalya@ti.com> Tested-by: Nishanth Menon <nm@ti.com>
* | clock_am43xx:Set the MAC clock to /5 for OPP100Steve Kipisz2015-02-16-0/+3
| | | | | | | | | | | | | | | | When EMAC is in the boot order, the boot ROM sets OPP50 and the MAC clock is set to /2. SPL needs to change it to /5 for Ethernet to generate the correct txclk. This patch sets it correctly. Signed-off-by: Steve Kipisz <s-kipisz2@ti.com>
* | ARM: DRA7-evm: DDR3: Update leveling valuesLokesh Vutla2015-02-16-30/+30
| | | | | | | | | | | | | | Update the software leveling parameters. This fixes the random crash seen on DRA7-evm. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
* | ARM: DRA7: EMIF: Update SDRAM_REF_CTRL register valueLokesh Vutla2015-02-16-4/+9
| | | | | | | | | | | | | | | | | | | | | | The value in SDRAM_REF_CTRL controls the delay time between the initial rising edge of DDR_RESETn to rising edge of DDR_CKE (JEDEC specs this as 500us). In order to achieve this, SDRAM_REF_CTRL should be written with a value corresponding to 500us delay before starting DDR initialization sequence, and configure proper value at the end of sequence. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
* | ARM: DRA72x: DDR3: Fix EMIF timings for 666MHz clockAngela Stegmaier2015-02-16-8/+8
| | | | | | | | | | | | | | | | | | | | DDR3 timing and latency paramenters were not configured correctly for 666MHz. Fixing the timing and latency values according to Data sheet. This fixes the random crashes seen on DRA72-evm. Signed-off-by: Angela Stegmaier <angelabaker@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
* | Merge git://git.denx.de/u-boot-samsungTom Rini2015-02-13-325/+324
|\ \
| * | Exynos: Clock: Cleanup soc_get_periph_rateAkshay Saraswat2015-02-13-39/+35
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Since we have src, div and pre-div mask bits defined corresponding to peripherals, calculation of clock specific to I2C appears redundant and confusing. Using clk_bit_info struct we can write calculations generic to all peripherals which makes code easy to understand and free from peripheral specific exceptions. Signed-off-by: Akshay Saraswat <akshay.s@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
| * | Exynos: clock: change mask bits as per peripheralAkshay Saraswat2015-02-13-73/+78
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | We have assumed and kept mask bits for divider and pre-divider as 0xf and 0xff, respectively. But these mask bits change from one peripheral to another, and hence, need to be specified in accordance with the peripherals. Signed-off-by: Akshay Saraswat <akshay.s@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
| * | Exynos5: Use clock_get_periph_rate generic APIAkshay Saraswat2015-02-13-235/+43
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Replacing SoC and peripheral specific function calls with generic clock_get_periph_rate calls to get the peripheral clocks. Also, removing dead code of peripheral and SoC specific function implementations which was used earlier for fetching peripheral clocks. This code is not being used anymore because of the introduction of generic clock_get_periph_rate function. Signed-off-by: Akshay Saraswat <akshay.s@samsung.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
| * | Exynos5: Fix exynos5_get_periph_rate calculationsAkshay Saraswat2015-02-13-8/+13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | exynos5_get_periph_rate function reads incorrect div for SDMMC2 & 3. It also reads prediv and does division only for SDMMC0 & 2 when actually various other peripherals need that. Adding changes to fix these mistakes in periph rate calculation. Signed-off-by: Akshay Saraswat <akshay.s@samsung.com> Reviewed-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
| * | Exynos542x: Add and enable get_periph_rate supportAkshay Saraswat2015-02-13-7/+146
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | We planned to fetch peripheral rate through one generic API per peripheral. These generic peripheral functions are in turn expected to fetch apt values from a function refactored as per SoC versions. This patch adds support for fetching peripheral rates for Exynos5420 and Exynos5800. Signed-off-by: Akshay Saraswat <akshay.s@samsung.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
| * | Exynos542x: Move exynos5420_get_pll_clk up and renameAkshay Saraswat2015-02-13-41/+41
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Moving exynos5420_get_pll_clk function definition up in the code to keep it together with rest of SoC_get_pll_clk functions. This makes code more legible and also removes the need of declaration when called before the position of definition in code. Also, renaming exynos5420_get_pll_clk to exynos542x_get_pll_clk because it is being used for both Exynos 5420 and 5800. Signed-off-by: Akshay Saraswat <akshay.s@samsung.com> Reviewed-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
| * | Exynos5: Fix compiler warnings due to clock_get_periph_rateAkshay Saraswat2015-02-13-31/+49
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Apparently, members of clk_bit_info array do not map correctly to the members of enum periph_id. This mapping got broken after we changed periph_id(s) to reflect interrupt number instead of their position in a sequence. This patch intends to fix above mentioned issue. Signed-off-by: Akshay Saraswat <akshay.s@samsung.com> Reviewed-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
| * | EXYNOS5: Add function to enable exynos5420 usbdev phy ctrlJoonyoung Shim2015-02-13-2/+26
| | | | | | | | | | | | | | | | | | | | | | | | | | | Exynos5420 has different registers with other exynos5 SoCs to control usb device phy, so need separated function to enable exynos5420 usb device phy. Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
| * | arm: exynos: fix the div value for set_mmc_clkJaehoon Chung2015-02-13-0/+4
| |/ | | | | | | | | | | | | | | | | | | | | The most exynos used the "Ratio + 1" as div value. And value at register is "Ratio". So if want to set exact value, it needs to subtract one. Value at register ("Ratio") = div - 1 Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
* | Merge git://git.denx.de/u-boot-dmTom Rini2015-02-13-0/+66
|\ \
| * | dm: Kconfig: Move CONFIG_SYS_MALLOC_F_LEN to KconfigSimon Glass2015-02-12-0/+24
| | | | | | | | | | | | | | | Move this option to Kconfig and update all boards. Signed-off-by: Simon Glass <sjg@chromium.org>
| * | dm: omap3: Move driver model CONFIGs to KconfigSimon Glass2015-02-12-0/+9
| | | | | | | | | | | | | | | | | | | | | Remove driver model CONFIGs from the board config headers and use Kconfig instead. Signed-off-by: Simon Glass <sjg@chromium.org>
| * | dm: tegra: Move driver model CONFIGs to KconfigSimon Glass2015-02-12-0/+18
| | | | | | | | | | | | | | | | | | | | | Remove driver model CONFIGs from the board config headers and use Kconfig instead. Signed-off-by: Simon Glass <sjg@chromium.org>
| * | dm: exynos: Move driver model CONFIGs to KconfigSimon Glass2015-02-12-0/+15
| |/ | | | | | | | | | | | | Remove driver model CONFIGs from the board config headers and use Kconfig instead. Signed-off-by: Simon Glass <sjg@chromium.org>
* | Merge branch 'rmobile' of git://git.denx.de/u-boot-shTom Rini2015-02-13-2/+16
|\ \ | |/ |/|
| * arm: rmobile: r8a7794: Enable SMP mode of Auxiliary Control RegisterNobuhiro Iwamatsu2015-02-13-1/+11
| | | | | | | | | | | | | | | | r8a7794 uses ARM SoC of CA7 base. If we want to use dcache on CA7, we need to enable SMP bit of Auxiliary Control Register. Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
| * arm: rmobile: Add SILK board supportVladimir Barinov2015-02-13-1/+5
| | | | | | | | | | | | | | | | | | | | | | SILK is an entry level development board based on R-Car E2 SoC (R8A7794) This commit supports the following peripherals: - SCIF, I2C, Ethernet, QSPI, MMC, USB Host Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com> Reviewed-by: Tom Rini <trini@ti.com> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
* | Merge branch 'master' of git://git.denx.de/u-boot-atmelTom Rini2015-02-10-0/+55
|\ \
| * | ARM: atmel: sama5d4: add interrupt redirect functionBo Shen2015-02-07-0/+12
| | | | | | | | | | | | | | | | | | Signed-off-by: Bo Shen <voice.shen@atmel.com> [fix subject] Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
| * | ARM: atmel: sama5d4: add bus matrix init functionBo Shen2015-02-07-0/+35
| | | | | | | | | | | | Signed-off-by: Bo Shen <voice.shen@atmel.com>
| * | ARM: atmel: clock: make it possible to configure HMX32Bo Shen2015-02-07-0/+8
| | | | | | | | | | | | Signed-off-by: Bo Shen <voice.shen@atmel.com>
generated by cgit v1.1 at 2024-12-29 08:59:53 +0000