summaryrefslogtreecommitdiff
path: root/board
Commit message (Collapse)AuthorAgeLines
* efi_loader: Add runtime servicesAlexander Graf2016-03-15-0/+30
| | | | | | | | | | | | | | | | | After booting has finished, EFI allows firmware to still interact with the OS using the "runtime services". These callbacks live in a separate address space, since they are available long after U-Boot has been overwritten by the OS. This patch adds enough framework for arbitrary code inside of U-Boot to become a runtime service with the right section attributes set. For now, we don't make use of it yet though. We could maybe in the future map U-boot environment variables to EFI variables here. Signed-off-by: Alexander Graf <agraf@suse.de> Reviewed-by: Simon Glass <sjg@chromium.org> Tested-by: Simon Glass <sjg@chromium.org>
* hikey: Add MMU tablesAlexander Graf2016-03-15-0/+21
| | | | | | | | The hikey runs with dcache disabled today. There really should be no reason not to use caches on AArch64, so let's add MMU definitions and enable the dcache. Signed-off-by: Alexander Graf <agraf@suse.de>
* vexpress64: Add MMU tablesAlexander Graf2016-03-15-0/+21
| | | | | | | | There's no good excuse for running with caches disabled on AArch64, so let's just move the vexpress64 target to enable the MMU and run with caches on. Signed-off-by: Alexander Graf <agraf@suse.de>
* thunderx: Move mmu table into board fileAlexander Graf2016-03-15-0/+24
| | | | | | | | | The MMU range table can vary depending on things we may only find out at runtime. While the very simple ThunderX variant does not change, other boards will, so move the definition from a static entry in a header file to the board file. Signed-off-by: Alexander Graf <agraf@suse.de>
* kc1: Clear reboot mode garbage on cold resetPaul Kocialkowski2016-03-15-0/+3
| | | | | | | Reboot mode garbage is found on cold reset and might be seen as valid on the next warm reset, thus it has to be cleared on cold reset. Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
* kc1: Power off when the power on reason is not a valid onePaul Kocialkowski2016-03-15-0/+16
| | | | | | | Some power on reasons are not desirable (e.g. too short press on the power button), battery plug. Thus, power off the device when one of those occurs. Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
* kc1: Boot to bootloader (fastboot) on ID pin pull-upPaul Kocialkowski2016-03-15-0/+9
| | | | | | USB ID pin pull-up indicates factory (fastboot) cable detection. Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
* kc1: OMAP4 reboot mode supportPaul Kocialkowski2016-03-15-0/+20
| | | | | | | | This adds support for the omap4 reboot mode mechanism and exports the reboot mode via an environment variable, that is used in the boot command to make it possible to boot from the recovery partition or fastboot. Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
* kc1: MUSB USB controller and fastboot USB gadget supportPaul Kocialkowski2016-03-15-0/+31
| | | | | | | | | This adds support for the MUSB USB dual-role controller in peripheral mode, with configuration options for the fastboot USB gadget. At this point, flashing the internal eMMC is support. Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
* Amazon Kindle Fire (first generation) codename kc1 supportPaul Kocialkowski2016-03-15-0/+228
| | | | | | | | | | The Amazon Kindle Fire (first generation) codename kc1 is a tablet that was released by Amazon back in 2011. It is using an OMAP4430 SoC GP version, which allows running U-Boot and the U-Boot SPL from the ground up. Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
* omap-common: Rename set_muxconf_regs_essential to set_muxconf_regsPaul Kocialkowski2016-03-15-9/+9
| | | | | | | There is no distinction between essential and non-essential mux configuration, so it doesn't make sense to have an "essential" prefix. Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
* omap_hsmmc: Board-specific TWL6030 MMC power initializationPaul Kocialkowski2016-03-15-1/+17
| | | | | | | | | | Boards using the TWL6030 regulator may not all use the LDOs the same way. Some might also not use MMC1 at all, so VMMC would't have to be enabled. This delegates TWL6030 MMC power initializations to board-specific functions, that may still call twl6030_power_mmc_init for the default behavior. Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
* sniper: Clear reboot mode garbage on cold resetPaul Kocialkowski2016-03-15-0/+3
| | | | | | | | Reboot mode garbage is found on cold reset and might be seen as valid on the next warm reset, thus it has to be cleared on cold reset. Signed-off-by: Paul Kocialkowski <contact@paulk.fr> Reviewed-by: Tom Rini <trini@konsulko.com>
* sniper: Get rid of reset_miscPaul Kocialkowski2016-03-15-5/+0
| | | | | | | | | | | There is no need to set the reboot mode to a particular value prior to reboot, since valid values will have been caught and cleared earlier. In addition, this breaks the reboot-bootloader fastboot call, by overriding the required value for fastboot. Signed-off-by: Paul Kocialkowski <contact@paulk.fr> Reviewed-by: Tom Rini <trini@konsulko.com>
* omap3: String-based reboot mode handlingPaul Kocialkowski2016-03-15-3/+3
| | | | | | | | This switches reboot mode handling to a string-based interface, that allows more flexibility to set a common interface with the next generations of OMAP devices. Signed-off-by: Paul Kocialkowski <contact@paulk.fr> Reviewed-by: Tom Rini <trini@konsulko.com>
* Merge git://git.denx.de/u-boot-dmTom Rini2016-03-14-6/+6
|\
| * dm: block: Rename device number member dev to devnumSimon Glass2016-03-14-2/+2
| | | | | | | | | | | | | | | | | | This is a device number, and we want to use 'dev' to mean a driver model device. Rename the member. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Stephen Warren <swarren@nvidia.com>
| * dm: part: Rename some partition functionsSimon Glass2016-03-14-1/+1
| | | | | | | | | | | | | | | | Rename three partition functions so that they start with part_. This makes it clear what they relate to. Signed-off-by: Simon Glass <sjg@chromium.org> Tested-by: Stephen Warren <swarren@nvidia.com>
| * dm: Drop the block_dev_desc_t typedefSimon Glass2016-03-14-3/+3
| | | | | | | | | | | | | | | | | | Use 'struct' instead of a typdef. Also since 'struct block_dev_desc' is long and causes 80-column violations, rename it to struct blk_desc. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com> Tested-by: Stephen Warren <swarren@nvidia.com>
* | ARM: DRA72-evm: Update mux and VIRTUAL/MANUAL mode timingsLokesh Vutla2016-03-14-134/+188
| | | | | | | | | | | | | | | | | | | | | | | | | | | | All the mux configurations needs to be done as part of the IODelay sequence to avoid glitch. Adding all the mux configuration, MANUAL/VIRTUAL mode configuration as needed for DRA72-evm. Also update the mux for SD card detect on DRA74-evm. Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Vignesh R <vigneshr@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* | ARM: DRA7-evm: Update memory info in banksLokesh Vutla2016-03-14-0/+14
| | | | | | | | | | | | | | | | | | | | Updating the memory banks properly so that DT is populated accordingly. And updating this only after DDR is properly detected by eeprom, so that git bisect is still maintained. Acked-by: Nishanth Menon <nm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
* | ARM: DRA7: EMIF: Add 4GB DDR settingsLokesh Vutla2016-03-14-3/+80
| | | | | | | | | | | | | | | | | | | | The REVH and later versions of DRA7-evm uses MICRON MT41K512M16HA-125 memory chips which is of size 4GB(2GB on EMIF1 and 2GB on EMIF2). Add support for the same. Acked-by: Nishanth Menon <nm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
* | ARM: DRA7: Move emif settings to board specific filesLokesh Vutla2016-03-14-0/+129
| | | | | | | | | | | | | | | | | | | | The newer versions of DRA7 boards has EEPROM populated with DDR size specified in it. Moving DRA7 specific emif related settings to board files so that emif settings can be identified based on EEPROM. Acked-by: Nishanth Menon <nm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
* | ARM: DRA7: Enable EEPROM supportLokesh Vutla2016-03-14-4/+58
| | | | | | | | | | | | | | | | Enable EEPROM support for DRA74-evm. Acked-by: Nishanth Menon <nm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
* | ti: common: dra7: Add standard access for board description EEPROMLokesh Vutla2016-03-14-0/+120
| | | | | | | | | | | | | | | | | | | | DRA7 EVM revH and later EVMs have EEPROM populated that can contain board description information such as name, revision, DDR definition, etc. Adding support for this EEPROM format. Acked-by: Nishanth Menon <nm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
* | ARM: AM57xx: Update EMIF registersLokesh Vutla2016-03-14-71/+65
| | | | | | | | | | | | | | | | There are certain EMIF timing failures seen on the some x15 boards. Updating the EMIF settings to get rid of these timing failures. Reviewed-by: Tom Rini <trini@konsulko.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
* | ARM: Various: Future-proof serial platdataAdam Ford2016-03-14-21/+21
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | A few boards still use ns16550_platdata structures, but assume the structure is going to be in a specific order. By explicitly naming each entry, this should also help 'future-proof' in the event the structure changes. Tested on the Logic PD Torpedo + Wireless. I only changed a handful of devices that used the same syntax as the Logic board. Appologies if I missed one or stepped on toes. Thanks to Derald Woods and Alexander Graf. Signed-off-by: Adam Ford <aford173@gmail.com> V6: Add fix to arch/arm/cpu/armv7/am33xx/board.c V5: Add fix to arch/arm/cpu/arm926ejs/lpc32xx/devices.c V4: Fix subject heading V3: Remove reg_offset out in all the structs. It was reverted out, and and if it did exist, it would get initialized to 0 by default. V2: I hastily copy-pasted the boards without looking at the UART number. This addresses 3 boards that use UART3 and not UART1. Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Simon Glass <sjg@chromium.org>
* | ARM: keystone2: use detected ddr3a sizeVitaly Andrianov2016-03-14-3/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Because KS2 u-boot works in 32 bit address space the existing ram_size global data field cannot be used. The maximum, which the get_ram_size() can detect is 2GB only. The ft_board_setup() needs the actual ddr3 size to fix up dtb. This commit introduces the ddr3_get_size() which uses SPD data to calculate the ddr3 size. This function replaces the "ddr3_size" environment variable, which was used to get the SODIMM size. For platforms, which don't have SODIMM with SPD and ddr3 is populated to a board a simple ddr3_get_size function that returns ddr3 size has to be implemented. See hardware-k2l.h Signed-off-by: Vitaly Andrianov <vitalya@ti.com> Signed-off-by: Nishanth Menon <nm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* | ARM: keystone2: use SPD info to configure K2HK and K2E DDR3Vitaly Andrianov2016-03-14-260/+62
| | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit replaces hard-coded EMIF and PHY DDR3 configurations for predefined SODIMMs to a calculated configuration. The SODIMM parameters are read from SODIMM's SPD and used to calculated the configuration. The current commit supports calculation for DDR3 with 1600MHz and 1333MHz only. Signed-off-by: Vitaly Andrianov <vitalya@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Nishanth Menon <nm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* | ARM: keystone2: K2G: Add support for different arm/device speedsLokesh Vutla2016-03-14-4/+46
| | | | | | | | | | | | | | | | | | | | The maximum device and arm speeds can be determined by reading EFUSE_BOOTROM register. As there is already a framework for reading this register, adding support for all possible speeds on k2g devices. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Nishanth Menon <nm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* | ARM: keystone2: Allow for board specific speed definitionsLokesh Vutla2016-03-14-5/+5
| | | | | | | | | | | | | | | | | | | | Its not compulsory that speed definition should be same on EFUSE_BOOTROM register for all keystone 2 devices. So, allow for board specific speed definitions. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Nishanth Menon <nm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* | arm: Add support for LEGO MINDSTORMS EV3David Lechner2016-03-14-0/+236
| | | | | | | | | | | | | | | | | | | | | | | | This is based on the davinci da850evm. It can boot from either the on-board 16MB flash or from a microSD card. It also reads board information from an I2C EEPROM. The EV3 itself initally boots from write-protected EEPROM, so no u-boot SPL is needed. Signed-off-by: David Lechner <david@lechnology.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* | board: ti: AM57xx: Add detection logic for AM57xx-evmKipisz, Steven2016-03-14-1/+71
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Current AM57xx evm supports both BeagleBoard-X15 (http://beagleboard.org/x15) and AM57xx EVM (http://www.ti.com/tool/tmdxevm5728). The AM572x EValuation Module(EVM) provides an affordable platform to quickly start evaluation of Sitara. ARM Cortex-A15 AM57x Processors (AM5728, AM5726, AM5718, AM5716) and accelerate development for HMI, machine vision, networking, medical imaging and many other industrial applications. This EVM is based on the same BeagleBoard-X15 Chassis and adds mPCIe, mSATA, LCD, touchscreen, Camera, push button and TI's wlink8 offering. Since the EEPROM contents are compatible between the BeagleBoard-X15 and the AM57xx-evm, we add support for the detection logic to enable support for various user programmable scripting capability. NOTE: U-boot configuration is currently a superset of AM57xx evm and BeagleBoard-X15 and no additional configuration tweaking is needed. This change also sets up the stage for future support of TI AM57xx EVMs to the same base bootloader build. Signed-off-by: Steve Kipisz <s-kipisz2@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Nishanth Menon <nm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* | ti: AM437x: Use generic EEPROM detection logicNishanth Menon2016-03-14-89/+38
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Now that we have a generic TI eeprom logic which can be reused across platforms, reuse the same. This revision also includes fixes identified by Dave Gerlach <d-gerlach@ti.com> Cc: Dave Gerlach <d-gerlach@ti.com> Signed-off-by: Nishanth Menon <nm@ti.com> Signed-off-by: Steven Kipisz <s-kipisz2@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* | ti: AM335x: Use generic EEPROM detection logicNishanth Menon2016-03-14-120/+59
| | | | | | | | | | | | | | | | | | | | Use the generic EEPROM detection logic instead of duplicating the AM eeprom logic. Signed-off-by: Nishanth Menon <nm@ti.com> Signed-off-by: Steven Kipisz <s-kipisz2@ti.com> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* | ARM: omap-common: Add standard access for board description EEPROMLokesh Vutla2016-03-14-0/+405
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Several TI EVMs have EEPROM that can contain board description information such as revision, DDR definition, serial number, etc. In just about all cases, these EEPROM are on the I2C bus and provides us the opportunity to centralize the generic operations involved. The on-board EEPROM on the BeagleBone Black, BeagleBone, AM335x EVM, AM43x GP EVM, AM57xx-evm, BeagleBoard-X15 share the same format. However, DRA-7* EVMs, OMAP4SDP use a modified format. We hence introduce logic which is generic between these platforms without enforcing any specific format. This allows the boards to use the relevant format for operations that they might choose. This module will compile for all TI SoC based boards when CONFIG_TI_I2C_BOARD_DETECT is enabled to have optimal build times for platforms that require this support. It is important to note that this logic is fundamental to the board configuration process such as DDR configuration which is needed in SPL, hence cannot be part of the standard u-boot driver model (which is available later in the process). Hence, to aid efficiency, the eeprom contents are copied over to SRAM scratchpad memory area at the first invocation to retrieve data. To prevent churn with cases such as DRA7, where eeprom format maybe incompatible, we introduce a generic common format in eeprom which is made available over accessor functions for usage. Special handling for BBG1 EEPROM had to be introduced thanks to the weird eeprom rev contents used. The follow on patches introduce the use of this library for AM335x, AM437x, and AM57xx. Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com> Signed-off-by: Steve Kipisz <s-kipisz2@ti.com> Signed-off-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Nishanth Menon <nm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* | Kconfig: Move CONFIG_FIT and related options to KconfigSimon Glass2016-03-14-0/+4
|/ | | | | | | | | | | | | | | | | | | | | | | | | | | | | There are already two FIT options in Kconfig but the CONFIG options are still in the header files. We need to do a proper move to fix this. Move these options to Kconfig and tidy up board configuration: CONFIG_FIT CONFIG_OF_BOARD_SETUP CONFIG_OF_SYSTEM_SETUP CONFIG_FIT_SIGNATURE CONFIG_FIT_BEST_MATCH CONFIG_FIT_VERBOSE CONFIG_OF_STDOUT_VIA_ALIAS CONFIG_RSA Unfortunately the first one is a little complicated. We need to make sure this option is not enabled in SPL by this change. Also this option is enabled automatically in the host builds by defining CONFIG_FIT in the image.h file. To solve this, add a new IMAGE_USE_FIT #define which can be used in files that are built on the host but must also build for U-Boot and SPL. Note: Masahiro's moveconfig.py script is amazing. Signed-off-by: Simon Glass <sjg@chromium.org> [trini: Add microblaze change, various configs/ re-applies] Signed-off-by: Tom Rini <trini@konsulko.com>
* mx6slevk: Fix the power up of the Ethernet PHYFabio Estevam2016-03-13-5/+4
| | | | | | | | | GPIO4_21 is the LAN8720 power pin, not the LAN8720 reset pin. Fix that, so that we can have Ethernet functional again. Reviewed-by: Tom Rini <trini@konsulko.com> Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
* board: tbs2910: Fix eMMC BOOTCFG valueSoeren Moch2016-03-02-1/+1
| | | | | | | | | Fix the BOOTCFG value for eMMC in the same way as commit 214c3f0f9921250eb336c7effadcc16158ea9df5 [imx: MX6DQ{P}/DL:SABRESD Fix bmode eMMC failure] did for sabresd. Signed-off-by: Soeren Moch <smoch@web.de>
* mx6qarm2: Update maintainer's emailsFabio Estevam2016-03-02-2/+2
| | | | | | Use the new NXP emails. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
* MAINTAINERS: Update Peng Fan's email addressFabio Estevam2016-03-02-3/+3
| | | | | | | Use Peng Fan's new NXP email address in MAINTAINERS files. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> Acked-by: Peng Fan <peng.fan@nxp.com>
* sniper: Various minor cleanups, missing Kconfig configs and reorganisationPaul Kocialkowski2016-02-29-331/+331
| | | | | | | | This introduces some minor cleanups, regarding aspects such as board name, code and headers organization as well as deprecated and missing config options. Signed-off-by: Paul Kocialkowski <contact@paulk.fr> Reviewed-by: Tom Rini <trini@konsulko.com>
* Merge branch 'master' of git://git.denx.de/u-boot-fsl-qoriqTom Rini2016-02-24-105/+95
|\
| * armv7: ls102xa: Move smmu and stream id initialization into the common soc codeAlison Wang2016-02-24-83/+2
| | | | | | | | | | | | | | | | The initialization for smmu and stream id is moved into the common soc code. Signed-off-by: Alison Wang <alison.wang@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
| * board: ls1043ardb: Modify pin-muxing code for USB and QE-HDLCZhao Qiang2016-02-24-10/+43
| | | | | | | | | | | | | | | | | | QE-HDLC and USB multi-use the pins, modify the pin-muxing code for them, when set "hwconfig=qe-hdlc" in uboot, assign the pins to QE-HDLC, if not, assgin it to USB Signed-off-by: Zhao Qiang <qiang.zhao@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
| * board: ls1043rdb: Move USB muxing config to config_board_muxZhao Qiang2016-02-24-15/+15
| | | | | | | | | | | | | | | | Pin-muxing code should be in config_board_mux, move USB muxing config to config_board_mux. Signed-off-by: Zhao Qiang <qiang.zhao@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
| * board: ls1043ardb: Add micro QE support for ls1043ardbZhao Qiang2016-02-24-0/+8
| | | | | | | | | | Signed-off-by: Zhao Qiang <qiang.zhao@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
| * armv8/ls1043aqds: Add USB support for ls1043aqdsQianyu Gong2016-02-24-0/+15
| | | | | | | | | | | | | | Add USB XHCI support for ls1043qds board. Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
| * qe: move drivers/qe/qe.h to include/fsl_qe.hQianyu Gong2016-02-24-4/+4
| | | | | | | | | | | | | | | | As the QE firmware struct is shared with Fman, move the header file out of drivers/qe/. Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
| * arm: ls1021a: Add QSPI or IFC support in SD boot for LS1021AQDS boardAlison Wang2016-02-24-3/+18
| | | | | | | | | | | | | | | | | | | | | | | | | | | | As QSPI and IFC are pin-multiplexed on LS1021A, only IFC is supported in SD boot now. For the customer's demand, QSPI needs to be supported in SD boot too. This patch adds QSPI or IFC support in SD boot according to the corresponding defconfig. For detail, ls1021aqds_sdcard_ifc_defconfig is used to support IFC in SD boot and ls1021aqds_sdcard_qspi_defconfig is used to support QSPI in SD boot. Signed-off-by: Alison Wang <alison.wang@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
generated by cgit v1.1 at 2024-10-31 17:33:35 +0000