1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
|
/*
* Copyright (C) 2016, Bin Meng <bmeng.cn@gmail.com>
*
* SPDX-License-Identifier: GPL-2.0+
*/
#ifndef _SMSC_SIO1007_H_
#define _SMSC_SIO1007_H_
/*
* The I/O base address of SIO1007 at power-up is determined by the SYSOPT0
* and SYSOPT1 pins at the deasserting edge of PCIRST#. The combination of
* SYSOPT0 and SYSOPT1 determines one of the following addresses.
*/
#define SIO1007_IOPORT0 0x002e
#define SIO1007_IOPORT1 0x004e
#define SIO1007_IOPORT2 0x162e
#define SIO1007_IOPORT3 0x164e
/* SIO1007 registers */
#define DEV_POWER_CTRL 0x02
#define UART1_POWER_ON (1 << 3)
#define UART2_POWER_ON (1 << 7)
#define UART1_IOBASE 0x24
#define UART2_IOBASE 0x25
#define UART_IRQ 0x28
#define RTR_IOBASE_HIGH 0x21
#define RTR_IOBASE_LOW 0x30
#define GPIO0_DIR 0x31
#define GPIO1_DIR 0x35
#define GPIO_DIR_INPUT 0
#define GPIO_DIR_OUTPUT 1
#define GPIO0_POL 0x32
#define GPIO1_POL 0x36
#define GPIO_POL_NO_INVERT 0
#define GPIO_POL_INVERT 1
#define GPIO0_TYPE 0x33
#define GPIO1_TYPE 0x37
#define GPIO_TYPE_PUSH_PULL 0
#define GPIO_TYPE_OPEN_DRAIN 1
#define DEV_ACTIVATE 0x3a
#define RTR_EN (1 << 1)
/* Runtime register offset */
#define GPIO0_DATA 0xc
#define GPIO1_DATA 0xe
/* Number of serial ports supported */
#define SIO1007_UART_NUM 2
/* Number of gpio pins supported */
#define GPIO_NUM_PER_GROUP 8
#define GPIO_GROUP_NUM 2
#define SIO1007_GPIO_NUM (GPIO_NUM_PER_GROUP * GPIO_GROUP_NUM)
/**
* Configure the I/O port address of the specified serial device and
* enable the serial device.
*
* @port: SIO1007 I/O port address
* @num: serial device number (0 or 1)
* @iobase: processor I/O port address to assign to this serial device
* @irq: processor IRQ number to assign to this serial device
*/
void sio1007_enable_serial(int port, int num, int iobase, int irq);
/**
* Configure the I/O port address of the runtime register block and
* enable the address decoding.
*
* @port: SIO1007 I/O port address
* @iobase: processor I/O port address to assign to the runtime registers
*/
void sio1007_enable_runtime(int port, int iobase);
/**
* Configure the direction/polority/type of a specified GPIO pin
*
* @port: SIO1007 I/O port address
* @gpio: GPIO number (0-7 for GP10-GP17, 8-15 for GP30-GP37)
* @dir: GPIO_DIR_INPUT or GPIO_DIR_OUTPUT
* @pol: GPIO_POL_NO_INVERT or GPIO_POL_INVERT
* @type: GPIO_TYPE_PUSH_PULL or GPIO_TYPE_OPEN_DRAIN
*/
void sio1007_gpio_config(int port, int gpio, int dir, int pol, int type);
/**
* Get a GPIO pin value.
* This will work whether the GPIO is an input or an output.
*
* @port: runtime register block I/O port address
* @gpio: GPIO number (0-7 for GP10-GP17, 8-15 for GP30-GP37)
* @return: 0 if low, 1 if high, -EINVAL if gpio number is invalid
*/
int sio1007_gpio_get_value(int port, int gpio);
/**
* Set a GPIO pin value.
* This will only work when the GPIO is configured as an output.
*
* @port: runtime register block I/O port address
* @gpio: GPIO number (0-7 for GP10-GP17, 8-15 for GP30-GP37)
* @val: 0 if low, 1 if high
*/
void sio1007_gpio_set_value(int port, int gpio, int val);
#endif /* _SMSC_SIO1007_H_ */
|
