1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383
384
385
386
387
388
389
390
391
392
393
394
395
396
397
398
399
400
401
402
403
404
405
406
407
408
409
410
411
412
413
414
415
416
417
418
419
420
421
422
423
424
425
426
427
428
429
430
431
432
433
|
/*
* (C) Copyright 2008
* Matthias Fuchs, esd gmbh, matthias.fuchs@esd-electronics.com
*
* based on the Sequoia board configuration by
* Stefan Roese, Jacqueline Pira-Ferriol and Alain Saurel
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
*/
/*
**********************************************************************
* DU440.h - configuration for esd's DU440 board (Power PC440EPx)
**********************************************************************
*/
#ifndef __CONFIG_H
#define __CONFIG_H
/*
* High Level Configuration Options
*/
#define CONFIG_DU440 1 /* Board is esd DU440 */
#define CONFIG_440EPX 1 /* Specific PPC440EPx */
#define CONFIG_4xx 1 /* ... PPC4xx family */
#define CONFIG_SYS_CLK_FREQ 33333400 /* external freq to pll */
#ifndef CONFIG_SYS_TEXT_BASE
#define CONFIG_SYS_TEXT_BASE 0xFFFA0000
#endif
#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
#define CONFIG_MISC_INIT_R 1 /* Call misc_init_r */
#define CONFIG_LAST_STAGE_INIT 1 /* last_stage_init */
/*
* Base addresses -- Note these are effective addresses where the
* actual resources get mapped (not physical addresses)
*/
#define CONFIG_SYS_MONITOR_LEN (384 * 1024) /* Reserve 384 kB for Monitor */
#define CONFIG_SYS_MALLOC_LEN (8 << 20) /* Reserve 8 MB for malloc() */
#define CONFIG_SYS_BOOT_BASE_ADDR 0xf0000000
#define CONFIG_SYS_SDRAM_BASE 0x00000000 /* _must_ be 0 */
#define CONFIG_SYS_FLASH_BASE 0xfc000000 /* start of FLASH */
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
#define CONFIG_SYS_NAND0_ADDR 0xd0000000 /* NAND Flash */
#define CONFIG_SYS_NAND1_ADDR 0xd0100000 /* NAND Flash */
#define CONFIG_SYS_OCM_BASE 0xe0010000 /* ocm */
#define CONFIG_SYS_PCI_BASE 0xe0000000 /* Internal PCI regs */
#define CONFIG_SYS_PCI_MEMBASE 0x80000000 /* mapped pci memory */
#define CONFIG_SYS_PCI_MEMBASE1 CONFIG_SYS_PCI_MEMBASE + 0x10000000
#define CONFIG_SYS_PCI_MEMBASE2 CONFIG_SYS_PCI_MEMBASE1 + 0x10000000
#define CONFIG_SYS_PCI_MEMBASE3 CONFIG_SYS_PCI_MEMBASE2 + 0x10000000
#define CONFIG_SYS_PCI_IOBASE 0xe8000000
#define CONFIG_SYS_PCI_SUBSYS_VENDORID PCI_VENDOR_ID_ESDGMBH
#define CONFIG_SYS_PCI_SUBSYS_ID 0x0444 /* device ID for DU440 */
#define CONFIG_SYS_USB2D0_BASE 0xe0000100
#define CONFIG_SYS_USB_DEVICE 0xe0000000
#define CONFIG_SYS_USB_HOST 0xe0000400
/*
* Initial RAM & stack pointer
*/
/* 440EPx/440GRx have 16KB of internal SRAM, so no need for D-Cache */
#define CONFIG_SYS_INIT_RAM_OCM 1 /* OCM as init ram */
#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_BASE /* OCM */
#define CONFIG_SYS_INIT_RAM_SIZE (4 << 10)
#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
/*
* Serial Port
*/
#define CONFIG_CONS_INDEX 1 /* Use UART0 */
#define CONFIG_SYS_NS16550
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE 1
#define CONFIG_SYS_NS16550_CLK get_serial_clock()
#undef CONFIG_SYS_EXT_SERIAL_CLOCK
#define CONFIG_BAUDRATE 115200
#define CONFIG_SERIAL_MULTI 1
#define CONFIG_SYS_BAUDRATE_TABLE \
{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
/*
* Video Port
*/
#define CONFIG_VIDEO
#define CONFIG_VIDEO_SMI_LYNXEM
#define CONFIG_CFB_CONSOLE
#define CONFIG_VIDEO_LOGO
#define CONFIG_VGA_AS_SINGLE_DEVICE
#define CONFIG_SPLASH_SCREEN
#define CONFIG_SPLASH_SCREEN_ALIGN
#define CONFIG_VIDEO_BMP_GZIP /* gzip compressed bmp images */
#define CONFIG_SYS_VIDEO_LOGO_MAX_SIZE (4 << 20) /* for decompressed img */
#define CONFIG_SYS_DEFAULT_VIDEO_MODE 0x31a /* 1280x1024,16bpp */
#define CONFIG_SYS_CONSOLE_IS_IN_ENV
#define CONFIG_SYS_ISA_IO CONFIG_SYS_PCI_IOBASE
/*
* Environment
*/
#define CONFIG_ENV_IS_IN_EEPROM 1 /* use FLASH for environment vars */
/*
* FLASH related
*/
#define CONFIG_SYS_FLASH_CFI /* The flash is CFI compatible */
#define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver */
#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE }
#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max number of sectors on one chip */
#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */
/* CFI_FLASH_PROTECTION make flash_protect hang sometimes -> disabled */
#define CONFIG_SYS_FLASH_PROTECTION 1 /* use hardware flash protection */
#define CONFIG_SYS_FLASH_EMPTY_INFO
#define CONFIG_SYS_FLASH_QUIET_TEST 1 /* don't warn upon unknown flash */
#ifdef CONFIG_ENV_IS_IN_FLASH
#define CONFIG_ENV_SECT_SIZE 0x20000 /* size of one complete sector */
#define CONFIG_ENV_ADDR ((-CONFIG_SYS_MONITOR_LEN)-CONFIG_ENV_SECT_SIZE)
#define CONFIG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */
/* Address and size of Redundant Environment Sector */
#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR-CONFIG_ENV_SECT_SIZE)
#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
#endif
#ifdef CONFIG_ENV_IS_IN_EEPROM
#define CONFIG_ENV_OFFSET 0 /* environment starts at */
/* the beginning of the EEPROM */
#define CONFIG_ENV_SIZE 0x1000 /* 4096 bytes may be used for env vars */
#endif
/*
* DDR SDRAM
*/
#define CONFIG_SYS_MBYTES_SDRAM (1024) /* 512 MiB TODO: remove */
#define CONFIG_DDR_DATA_EYE /* use DDR2 optimization */
#define CONFIG_SYS_MEM_TOP_HIDE (4 << 10) /* don't use last 4kbytes */
/* 440EPx errata CHIP 11 */
#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for setup */
#define CONFIG_DDR_ECC /* Use ECC when available */
#define SPD_EEPROM_ADDRESS {0x50}
#define CONFIG_PROG_SDRAM_TLB
/*
* I2C
*/
#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
#undef CONFIG_SOFT_I2C /* I2C bit-banged */
#define CONFIG_PPC4XX_I2C /* use PPC4xx driver */
#define CONFIG_SYS_I2C_SPEED 100000 /* I2C speed and slave address */
#define CONFIG_SYS_I2C_SLAVE 0x7F
#define CONFIG_I2C_MULTI_BUS 1
#define CONFIG_SYS_SPD_BUS_NUM 0
#define IIC1_MCP3021_ADDR 0x4d
#define IIC1_USB2507_ADDR 0x2c
#ifdef CONFIG_I2C_MULTI_BUS
#define CONFIG_SYS_I2C_NOPROBES {{1, IIC1_USB2507_ADDR}}
#endif
#define CONFIG_SYS_I2C_MULTI_EEPROMS
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x54
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10
#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 0x01
#define CONFIG_SYS_EEPROM_WREN 1
#define CONFIG_SYS_I2C_BOOT_EEPROM_ADDR 0x52
/*
* standard dtt sensor configuration - bottom bit will determine local or
* remote sensor of the TMP401
*/
#define CONFIG_DTT_SENSORS { 0, 1 }
/*
* The PMC440 uses a TI TMP401 temperature sensor. This part
* is basically compatible to the ADM1021 that is supported
* by U-Boot.
*
* - i2c addr 0x4c
* - conversion rate 0x02 = 0.25 conversions/second
* - ALERT ouput disabled
* - local temp sensor enabled, min set to 0 deg, max set to 70 deg
* - remote temp sensor enabled, min set to 0 deg, max set to 70 deg
*/
#define CONFIG_DTT_ADM1021
#define CONFIG_SYS_DTT_ADM1021 { { 0x4c, 0x02, 0, 1, 70, 0, 1, 70, 0} }
/*
* RTC stuff
*/
#define CONFIG_RTC_DS1338
#define CONFIG_SYS_I2C_RTC_ADDR 0x68
#undef CONFIG_BOOTARGS
#define CONFIG_EXTRA_ENV_SETTINGS \
"netdev=eth0\0" \
"ethrotate=no\0" \
"hostname=du440\0" \
"nfsargs=setenv bootargs root=/dev/nfs rw " \
"nfsroot=${serverip}:${rootpath}\0" \
"ramargs=setenv bootargs root=/dev/ram rw\0" \
"addip=setenv bootargs ${bootargs} " \
"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
":${hostname}:${netdev}:off panic=1\0" \
"addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
"flash_self=run ramargs addip addtty optargs;" \
"bootm ${kernel_addr} ${ramdisk_addr}\0" \
"net_nfs=tftp 200000 ${img};run nfsargs addip addtty optargs;" \
"bootm\0" \
"rootpath=/tftpboot/du440/target_root_du440\0" \
"img=/tftpboot/du440/uImage\0" \
"kernel_addr=FFC00000\0" \
"ramdisk_addr=FFE00000\0" \
"initrd_high=30000000\0" \
"load=tftp 100000 /tftpboot/du440/u-boot.bin\0" \
"update=protect off FFFA0000 FFFFFFFF;era FFFA0000 FFFFFFFF;" \
"cp.b 100000 FFFA0000 60000\0" \
""
#define CONFIG_PREBOOT /* enable preboot variable */
#define CONFIG_BOOTDELAY 3 /* autoboot after 5 seconds */
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
#ifndef __ASSEMBLY__
int du440_phy_addr(int devnum);
#endif
#define CONFIG_PPC4xx_EMAC
#define CONFIG_IBM_EMAC4_V4 1
#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_PHY_ADDR du440_phy_addr(0) /* PHY address */
#define CONFIG_PHY_RESET 1 /* reset phy upon startup */
#undef CONFIG_PHY_GIGE /* no GbE detection */
#define CONFIG_HAS_ETH0
#define CONFIG_SYS_RX_ETH_BUFFER 128
#define CONFIG_NET_MULTI 1
#define CONFIG_HAS_ETH1 1 /* add support for "eth1addr" */
#define CONFIG_PHY1_ADDR du440_phy_addr(1)
/*
* USB
*/
#define CONFIG_USB_OHCI_NEW
#define CONFIG_USB_STORAGE
#define CONFIG_SYS_OHCI_BE_CONTROLLER
#define CONFIG_SYS_USB_OHCI_CPU_INIT 1
#define CONFIG_SYS_USB_OHCI_REGS_BASE CONFIG_SYS_USB_HOST
#define CONFIG_SYS_USB_OHCI_SLOT_NAME "du440"
#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 15
/* Comment this out to enable USB 1.1 device */
#define USB_2_0_DEVICE
/* Partitions */
#define CONFIG_MAC_PARTITION
#define CONFIG_DOS_PARTITION
#define CONFIG_ISO_PARTITION
#include <config_cmd_default.h>
#define CONFIG_CMD_ASKENV
#define CONFIG_CMD_BMP
#define CONFIG_CMD_BSP
#define CONFIG_CMD_DATE
#define CONFIG_CMD_DHCP
#define CONFIG_CMD_DIAG
#define CONFIG_CMD_DTT
#define CONFIG_CMD_EEPROM
#define CONFIG_CMD_ELF
#define CONFIG_CMD_FAT
#define CONFIG_CMD_I2C
#define CONFIG_CMD_IRQ
#define CONFIG_CMD_MII
#define CONFIG_CMD_NAND
#define CONFIG_CMD_NET
#define CONFIG_CMD_NFS
#define CONFIG_CMD_PCI
#define CONFIG_CMD_PING
#define CONFIG_CMD_REGINFO
#define CONFIG_CMD_SDRAM
#define CONFIG_CMD_SOURCE
#define CONFIG_CMD_USB
#define CONFIG_SUPPORT_VFAT
/*
* Miscellaneous configurable options
*/
#define CONFIG_SYS_LONGHELP /* undef to save memory */
#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
#if defined(CONFIG_CMD_KGDB)
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#else
#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
#endif
/* Print Buffer Size */
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
#define CONFIG_SYS_MEMTEST_START 0x00400000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0x3f000000 /* 4 ... < 1GB DRAM */
#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
#define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_into (bd_t) */
#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */
#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
#define CONFIG_LOOPW 1 /* enable loopw command */
#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */
#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
#define CONFIG_AUTOBOOT_KEYED 1
#define CONFIG_AUTOBOOT_PROMPT \
"Press SPACE to abort autoboot in %d seconds\n", bootdelay
#define CONFIG_AUTOBOOT_DELAY_STR "d"
#define CONFIG_AUTOBOOT_STOP_STR " "
/*
* PCI stuff
*/
#define CONFIG_PCI /* include pci support */
#define CONFIG_PCI_PNP /* do (not) pci plug-and-play */
#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
#define CONFIG_SYS_PCI_TARGBASE 0x80000000 /* PCIaddr mapped to CONFIG_SYS_PCI_MEMBASE*/
/* Board-specific PCI */
#define CONFIG_SYS_PCI_TARGET_INIT
#define CONFIG_SYS_PCI_MASTER_INIT
/*
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
/*
* External Bus Controller (EBC) Setup
*/
#define CONFIG_SYS_FLASH CONFIG_SYS_FLASH_BASE
#define CONFIG_SYS_CPLD_BASE 0xC0000000
#define CONFIG_SYS_CPLD_RANGE 0x00000010
#define CONFIG_SYS_DUMEM_BASE 0xC0100000
#define CONFIG_SYS_DUMEM_RANGE 0x00100000
#define CONFIG_SYS_DUIO_BASE 0xC0200000
#define CONFIG_SYS_DUIO_RANGE 0x00010000
#define CONFIG_SYS_NAND0_CS 2 /* NAND chip connected to CSx */
#define CONFIG_SYS_NAND1_CS 3 /* NAND chip connected to CSx */
/* Memory Bank 0 (NOR-FLASH) initialization */
#define CONFIG_SYS_EBC_PB0AP 0x04017200
#define CONFIG_SYS_EBC_PB0CR (CONFIG_SYS_FLASH_BASE | 0xda000)
/* Memory Bank 1 (CPLD, 16 bytes needed, but 1MB is minimum) */
#define CONFIG_SYS_EBC_PB1AP 0x018003c0
#define CONFIG_SYS_EBC_PB1CR (CONFIG_SYS_CPLD_BASE | 0x18000)
/* Memory Bank 2 (NAND-FLASH) initialization */
#define CONFIG_SYS_EBC_PB2AP 0x018003c0
#define CONFIG_SYS_EBC_PB2CR (CONFIG_SYS_NAND0_ADDR | 0x1c000)
/* Memory Bank 3 (NAND-FLASH) initialization */
#define CONFIG_SYS_EBC_PB3AP 0x018003c0
#define CONFIG_SYS_EBC_PB3CR (CONFIG_SYS_NAND1_ADDR | 0x1c000)
/* Memory Bank 4 (DUMEM, 1MB) initialization */
#define CONFIG_SYS_EBC_PB4AP 0x018053c0
#define CONFIG_SYS_EBC_PB4CR (CONFIG_SYS_DUMEM_BASE | 0x18000)
/* Memory Bank 5 (DUIO, 64KB needed, but 1MB is minimum) */
#define CONFIG_SYS_EBC_PB5AP 0x018053c0
#define CONFIG_SYS_EBC_PB5CR (CONFIG_SYS_DUIO_BASE | 0x18000)
/*
* NAND FLASH
*/
#define CONFIG_SYS_MAX_NAND_DEVICE 2
#define CONFIG_SYS_NAND_SELECT_DEVICE 1 /* nand driver supports mutipl. chips */
#define CONFIG_SYS_NAND_BASE_LIST {CONFIG_SYS_NAND0_ADDR + CONFIG_SYS_NAND0_CS, \
CONFIG_SYS_NAND1_ADDR + CONFIG_SYS_NAND1_CS}
#if defined(CONFIG_CMD_KGDB)
#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
#endif
#define CONFIG_SOURCE 1
#define CONFIG_OF_LIBFDT
#define CONFIG_OF_BOARD_SETUP
#endif /* __CONFIG_H */
|
