1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
|
/*
* (C) Copyright 2009
* Vipin Kumar, ST Micoelectronics, vipin.kumar@st.com.
*
* Copyright (C) 2012 Stefan Roese <sr@denx.de>
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include <common.h>
#include <micrel.h>
#include <nand.h>
#include <netdev.h>
#include <phy.h>
#include <rtc.h>
#include <asm/io.h>
#include <asm/arch/hardware.h>
#include <asm/arch/spr_defs.h>
#include <asm/arch/spr_misc.h>
#include <linux/mtd/fsmc_nand.h>
#include "fpga.h"
static struct nand_chip nand_chip[CONFIG_SYS_MAX_NAND_DEVICE];
int board_init(void)
{
/*
* X600 is equipped with an M41T82 RTC. This RTC has the
* HT bit (Halt Update), which needs to be cleared upon
* power-up. Otherwise the RTC is halted.
*/
rtc_reset();
return spear_board_init(MACH_TYPE_SPEAR600);
}
int board_late_init(void)
{
/*
* Monitor and env protection on by default
*/
flash_protect(FLAG_PROTECT_SET,
CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE +
CONFIG_SYS_SPL_LEN + CONFIG_SYS_MONITOR_LEN +
2 * CONFIG_ENV_SECT_SIZE - 1,
&flash_info[0]);
/* Init FPGA subsystem */
x600_init_fpga();
return 0;
}
/*
* board_nand_init - Board specific NAND initialization
* @nand: mtd private chip structure
*
* Called by nand_init_chip to initialize the board specific functions
*/
void board_nand_init(void)
{
struct misc_regs *const misc_regs_p =
(struct misc_regs *)CONFIG_SPEAR_MISCBASE;
struct nand_chip *nand = &nand_chip[0];
if (!(readl(&misc_regs_p->auto_cfg_reg) & MISC_NANDDIS))
fsmc_nand_init(nand);
}
int board_phy_config(struct phy_device *phydev)
{
unsigned short id1, id2;
/* check whether KSZ9031 or AR8035 has to be configured */
id1 = phy_read(phydev, MDIO_DEVAD_NONE, 2);
id2 = phy_read(phydev, MDIO_DEVAD_NONE, 3);
if ((id1 == 0x22) && ((id2 & 0xFFF0) == 0x1620)) {
/* PHY configuration for Micrel KSZ9031 */
printf("PHY KSZ9031 detected - ");
phy_write(phydev, MDIO_DEVAD_NONE, MII_CTRL1000, 0x1c00);
/* control data pad skew - devaddr = 0x02, register = 0x04 */
ksz9031_phy_extended_write(phydev, 0x02,
MII_KSZ9031_EXT_RGMII_CTRL_SIG_SKEW,
MII_KSZ9031_MOD_DATA_NO_POST_INC,
0x0000);
/* rx data pad skew - devaddr = 0x02, register = 0x05 */
ksz9031_phy_extended_write(phydev, 0x02,
MII_KSZ9031_EXT_RGMII_RX_DATA_SKEW,
MII_KSZ9031_MOD_DATA_NO_POST_INC,
0x0000);
/* tx data pad skew - devaddr = 0x02, register = 0x05 */
ksz9031_phy_extended_write(phydev, 0x02,
MII_KSZ9031_EXT_RGMII_TX_DATA_SKEW,
MII_KSZ9031_MOD_DATA_NO_POST_INC,
0x0000);
/* gtx and rx clock pad skew - devaddr = 0x02, reg = 0x08 */
ksz9031_phy_extended_write(phydev, 0x02,
MII_KSZ9031_EXT_RGMII_CLOCK_SKEW,
MII_KSZ9031_MOD_DATA_NO_POST_INC,
0x03FF);
} else {
/* PHY configuration for Vitesse VSC8641 */
printf("PHY VSC8641 detected - ");
/* Extended PHY control 1, select GMII */
phy_write(phydev, MDIO_DEVAD_NONE, 23, 0x0020);
/* Software reset necessary after GMII mode selction */
phy_reset(phydev);
/* Enable extended page register access */
phy_write(phydev, MDIO_DEVAD_NONE, 31, 0x0001);
/* 17e: Enhanced LED behavior, needs to be written twice */
phy_write(phydev, MDIO_DEVAD_NONE, 17, 0x09ff);
phy_write(phydev, MDIO_DEVAD_NONE, 17, 0x09ff);
/* 16e: Enhanced LED method select */
phy_write(phydev, MDIO_DEVAD_NONE, 16, 0xe0ea);
/* Disable extended page register access */
phy_write(phydev, MDIO_DEVAD_NONE, 31, 0x0000);
/* Enable clock output pin */
phy_write(phydev, MDIO_DEVAD_NONE, 18, 0x0049);
}
if (phydev->drv->config)
phydev->drv->config(phydev);
return 0;
}
int board_eth_init(bd_t *bis)
{
int ret = 0;
if (designware_initialize(CONFIG_SPEAR_ETHBASE,
PHY_INTERFACE_MODE_GMII) >= 0)
ret++;
return ret;
}
|
