1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
|
/*
* Board functions for Compulab CM-T335 board
*
* Copyright (C) 2013, Compulab Ltd - http://compulab.co.il/
*
* Author: Ilya Ledvich <ilya@compulab.co.il>
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include <common.h>
#include <errno.h>
#include <miiphy.h>
#include <cpsw.h>
#include <asm/arch/sys_proto.h>
#include <asm/arch/hardware_am33xx.h>
#include <asm/io.h>
#include <asm/gpio.h>
#include "../common/eeprom.h"
DECLARE_GLOBAL_DATA_PTR;
/*
* Basic board specific setup. Pinmux has been handled already.
*/
int board_init(void)
{
gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
gpmc_init();
#if defined(CONFIG_STATUS_LED) && defined(STATUS_LED_BOOT)
status_led_set(STATUS_LED_BOOT, STATUS_LED_OFF);
#endif
return 0;
}
#if defined (CONFIG_DRIVER_TI_CPSW) && !defined(CONFIG_SPL_BUILD)
static void cpsw_control(int enabled)
{
/* VTP can be added here */
return;
}
static struct cpsw_slave_data cpsw_slave = {
.slave_reg_ofs = 0x208,
.sliver_reg_ofs = 0xd80,
.phy_addr = 0,
.phy_if = PHY_INTERFACE_MODE_RGMII,
};
static struct cpsw_platform_data cpsw_data = {
.mdio_base = CPSW_MDIO_BASE,
.cpsw_base = CPSW_BASE,
.mdio_div = 0xff,
.channels = 8,
.cpdma_reg_ofs = 0x800,
.slaves = 1,
.slave_data = &cpsw_slave,
.ale_reg_ofs = 0xd00,
.ale_entries = 1024,
.host_port_reg_ofs = 0x108,
.hw_stats_reg_ofs = 0x900,
.bd_ram_ofs = 0x2000,
.mac_control = (1 << 5),
.control = cpsw_control,
.host_port_num = 0,
.version = CPSW_CTRL_VERSION_2,
};
/* PHY reset GPIO */
#define GPIO_PHY_RST GPIO_PIN(3, 7)
static void board_phy_init(void)
{
gpio_request(GPIO_PHY_RST, "phy_rst");
gpio_direction_output(GPIO_PHY_RST, 0);
mdelay(2);
gpio_set_value(GPIO_PHY_RST, 1);
mdelay(2);
}
static void get_efuse_mac_addr(uchar *enetaddr)
{
uint32_t mac_hi, mac_lo;
struct ctrl_dev *cdev = (struct ctrl_dev *)CTRL_DEVICE_BASE;
mac_lo = readl(&cdev->macid0l);
mac_hi = readl(&cdev->macid0h);
enetaddr[0] = mac_hi & 0xFF;
enetaddr[1] = (mac_hi & 0xFF00) >> 8;
enetaddr[2] = (mac_hi & 0xFF0000) >> 16;
enetaddr[3] = (mac_hi & 0xFF000000) >> 24;
enetaddr[4] = mac_lo & 0xFF;
enetaddr[5] = (mac_lo & 0xFF00) >> 8;
}
/*
* Routine: handle_mac_address
* Description: prepare MAC address for on-board Ethernet.
*/
static int handle_mac_address(void)
{
uchar enetaddr[6];
int rv;
rv = eth_getenv_enetaddr("ethaddr", enetaddr);
if (rv)
return 0;
rv = cl_eeprom_read_mac_addr(enetaddr, CONFIG_SYS_I2C_EEPROM_BUS);
if (rv)
get_efuse_mac_addr(enetaddr);
if (!is_valid_ethaddr(enetaddr))
return -1;
return eth_setenv_enetaddr("ethaddr", enetaddr);
}
#define AR8051_PHY_DEBUG_ADDR_REG 0x1d
#define AR8051_PHY_DEBUG_DATA_REG 0x1e
#define AR8051_DEBUG_RGMII_CLK_DLY_REG 0x5
#define AR8051_RGMII_TX_CLK_DLY 0x100
int board_eth_init(bd_t *bis)
{
int rv, n = 0;
const char *devname;
struct ctrl_dev *cdev = (struct ctrl_dev *)CTRL_DEVICE_BASE;
rv = handle_mac_address();
if (rv)
printf("No MAC address found!\n");
writel(RGMII_MODE_ENABLE | RGMII_INT_DELAY, &cdev->miisel);
board_phy_init();
rv = cpsw_register(&cpsw_data);
if (rv < 0)
printf("Error %d registering CPSW switch\n", rv);
else
n += rv;
/*
* CPSW RGMII Internal Delay Mode is not supported in all PVT
* operating points. So we must set the TX clock delay feature
* in the AR8051 PHY. Since we only support a single ethernet
* device, we only do this for the first instance.
*/
devname = miiphy_get_current_dev();
miiphy_write(devname, 0x0, AR8051_PHY_DEBUG_ADDR_REG,
AR8051_DEBUG_RGMII_CLK_DLY_REG);
miiphy_write(devname, 0x0, AR8051_PHY_DEBUG_DATA_REG,
AR8051_RGMII_TX_CLK_DLY);
return n;
}
#endif /* CONFIG_DRIVER_TI_CPSW && !CONFIG_SPL_BUILD */
|
