1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
|
/*
* Copyright (C) 2015, Bachmann electronic GmbH
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include <common.h>
#include <spl.h>
#include <asm/arch/mx6-ddr.h>
DECLARE_GLOBAL_DATA_PTR;
/* Configure MX6Q/DUAL mmdc DDR io registers */
static struct mx6dq_iomux_ddr_regs ot1200_ddr_ioregs = {
/* SDCLK[0:1], CAS, RAS, Reset: Differential input, 48ohm */
.dram_sdclk_0 = 0x00000028,
.dram_sdclk_1 = 0x00000028,
.dram_cas = 0x00000028,
.dram_ras = 0x00000028,
.dram_reset = 0x00000028,
/* SDCKE[0:1]: 100k pull-up */
.dram_sdcke0 = 0x00003000,
.dram_sdcke1 = 0x00003000,
/* SDBA2: pull-up disabled */
.dram_sdba2 = 0x00000000,
/* SDODT[0:1]: 100k pull-up, 48 ohm */
.dram_sdodt0 = 0x00000028,
.dram_sdodt1 = 0x00000028,
/* SDQS[0:7]: Differential input, 48 ohm */
.dram_sdqs0 = 0x00000028,
.dram_sdqs1 = 0x00000028,
.dram_sdqs2 = 0x00000028,
.dram_sdqs3 = 0x00000028,
.dram_sdqs4 = 0x00000028,
.dram_sdqs5 = 0x00000028,
.dram_sdqs6 = 0x00000028,
.dram_sdqs7 = 0x00000028,
/* DQM[0:7]: Differential input, 48 ohm */
.dram_dqm0 = 0x00000028,
.dram_dqm1 = 0x00000028,
.dram_dqm2 = 0x00000028,
.dram_dqm3 = 0x00000028,
.dram_dqm4 = 0x00000028,
.dram_dqm5 = 0x00000028,
.dram_dqm6 = 0x00000028,
.dram_dqm7 = 0x00000028,
};
/* Configure MX6Q/DUAL mmdc GRP io registers */
static struct mx6dq_iomux_grp_regs ot1200_grp_ioregs = {
/* DDR3 */
.grp_ddr_type = 0x000c0000,
.grp_ddrmode_ctl = 0x00020000,
/* Disable DDR pullups */
.grp_ddrpke = 0x00000000,
/* ADDR[00:16], SDBA[0:1]: 48 ohm */
.grp_addds = 0x00000028,
/* CS0/CS1/SDBA2/CKE0/CKE1/SDWE: 48 ohm */
.grp_ctlds = 0x00000028,
/* DATA[00:63]: Differential input, 48 ohm */
.grp_ddrmode = 0x00020000,
.grp_b0ds = 0x00000028,
.grp_b1ds = 0x00000028,
.grp_b2ds = 0x00000028,
.grp_b3ds = 0x00000028,
.grp_b4ds = 0x00000028,
.grp_b5ds = 0x00000028,
.grp_b6ds = 0x00000028,
.grp_b7ds = 0x00000028,
};
static struct mx6_ddr_sysinfo ot1200_ddr_sysinfo = {
/* Width of data bus: 0=16, 1=32, 2=64 */
.dsize = 2,
/* config for full 4GB range so that get_mem_size() works */
.cs_density = 32, /* 32Gb per CS */
/* Single chip select */
.ncs = 1,
.cs1_mirror = 0, /* war 0 */
.rtt_wr = 1, /* DDR3_RTT_60_OHM - RTT_Wr = RZQ/4 */
.rtt_nom = 1, /* DDR3_RTT_60_OHM - RTT_Nom = RZQ/4 */
.walat = 1, /* Write additional latency */
.ralat = 5, /* Read additional latency */
.mif3_mode = 3, /* Command prediction working mode */
.bi_on = 1, /* Bank interleaving enabled */ /* war 1 */
.sde_to_rst = 0x10, /* 14 cycles, 200us (JEDEC default) */
.rst_to_cke = 0x23, /* 33 cycles, 500us (JEDEC default) */
};
/* MT41K128M16JT-125 */
static struct mx6_ddr3_cfg micron_2gib_1600 = {
.mem_speed = 1600,
.density = 2,
.width = 16,
.banks = 8,
.rowaddr = 14,
.coladdr = 10,
.pagesz = 2,
.trcd = 1375,
.trcmin = 4875,
.trasmin = 3500,
.SRT = 1,
};
static struct mx6_mmdc_calibration micron_2gib_1600_mmdc_calib = {
/* write leveling calibration determine */
.p0_mpwldectrl0 = 0x00260025,
.p0_mpwldectrl1 = 0x00270021,
.p1_mpwldectrl0 = 0x00180034,
.p1_mpwldectrl1 = 0x00180024,
/* Read DQS Gating calibration */
.p0_mpdgctrl0 = 0x04380344,
.p0_mpdgctrl1 = 0x0330032C,
.p1_mpdgctrl0 = 0x0338033C,
.p1_mpdgctrl1 = 0x032C0300,
/* Read Calibration: DQS delay relative to DQ read access */
.p0_mprddlctl = 0x3C2E3238,
.p1_mprddlctl = 0x3A2E303C,
/* Write Calibration: DQ/DM delay relative to DQS write access */
.p0_mpwrdlctl = 0x36384036,
.p1_mpwrdlctl = 0x442E4438,
};
static void ot1200_spl_dram_init(void)
{
mx6dq_dram_iocfg(64, &ot1200_ddr_ioregs, &ot1200_grp_ioregs);
mx6_dram_cfg(&ot1200_ddr_sysinfo, µn_2gib_1600_mmdc_calib,
µn_2gib_1600);
}
/*
* called from C runtime startup code (arch/arm/lib/crt0.S:_main)
* - we have a stack and a place to store GD, both in SRAM
* - no variable global data is available
*/
void board_init_f(ulong dummy)
{
/* setup AIPS and disable watchdog */
arch_cpu_init();
/* iomux and setup of i2c */
board_early_init_f();
/* setup GP timer */
timer_init();
/* UART clocks enabled and gd valid - init serial console */
preloader_console_init();
/* configure MMDC for SDRAM width/size and per-model calibration */
ot1200_spl_dram_init();
/* Clear the BSS. */
memset(__bss_start, 0, __bss_end - __bss_start);
/* load/boot image from boot device */
board_init_r(NULL, 0);
}
|
