1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
|
/*
* Copyright (C) 2016 Stefan Roese <sr@denx.de>
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include <common.h>
#include <i2c.h>
#include <asm/io.h>
#include <asm/arch/cpu.h>
#include <asm/arch/soc.h>
DECLARE_GLOBAL_DATA_PTR;
/* IO expander I2C device */
#define I2C_IO_EXP_ADDR 0x22
#define I2C_IO_CFG_REG_0 0x6
#define I2C_IO_DATA_OUT_REG_0 0x2
#define I2C_IO_REG_0_SATA_OFF 2
#define I2C_IO_REG_0_USB_H_OFF 1
int board_early_init_f(void)
{
/* Nothing to do (yet), perhaps later some pin-muxing etc */
return 0;
}
int board_init(void)
{
/* adress of boot parameters */
gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
return 0;
}
/* Board specific AHCI / SATA enable code */
int board_ahci_enable(void)
{
struct udevice *dev;
int ret;
u8 buf[8];
/* Configure IO exander PCA9555: 7bit address 0x22 */
ret = i2c_get_chip_for_busnum(0, I2C_IO_EXP_ADDR, 1, &dev);
if (ret) {
printf("Cannot find PCA9555: %d\n", ret);
return 0;
}
ret = dm_i2c_read(dev, I2C_IO_CFG_REG_0, buf, 1);
if (ret) {
printf("Failed to read IO expander value via I2C\n");
return -EIO;
}
/*
* Enable SATA power via IO expander connected via I2C by setting
* the corresponding bit to output mode to enable power for SATA
*/
buf[0] &= ~(1 << I2C_IO_REG_0_SATA_OFF);
ret = dm_i2c_write(dev, I2C_IO_CFG_REG_0, buf, 1);
if (ret) {
printf("Failed to set IO expander via I2C\n");
return -EIO;
}
return 0;
}
/* Board specific xHCI enable code */
int board_xhci_enable(void)
{
struct udevice *dev;
int ret;
u8 buf[8];
/* Configure IO exander PCA9555: 7bit address 0x22 */
ret = i2c_get_chip_for_busnum(0, I2C_IO_EXP_ADDR, 1, &dev);
if (ret) {
printf("Cannot find PCA9555: %d\n", ret);
return 0;
}
printf("Enable USB VBUS\n");
/*
* Read configuration (direction) and set VBUS pin as output
* (reset pin = output)
*/
ret = dm_i2c_read(dev, I2C_IO_CFG_REG_0, buf, 1);
if (ret) {
printf("Failed to read IO expander value via I2C\n");
return -EIO;
}
buf[0] &= ~(1 << I2C_IO_REG_0_USB_H_OFF);
ret = dm_i2c_write(dev, I2C_IO_CFG_REG_0, buf, 1);
if (ret) {
printf("Failed to set IO expander via I2C\n");
return -EIO;
}
/* Read VBUS output value and disable it */
ret = dm_i2c_read(dev, I2C_IO_DATA_OUT_REG_0, buf, 1);
if (ret) {
printf("Failed to read IO expander value via I2C\n");
return -EIO;
}
buf[0] &= ~(1 << I2C_IO_REG_0_USB_H_OFF);
ret = dm_i2c_write(dev, I2C_IO_DATA_OUT_REG_0, buf, 1);
if (ret) {
printf("Failed to set IO expander via I2C\n");
return -EIO;
}
/*
* Required delay for configuration to settle - must wait for
* power on port is disabled in case VBUS signal was high,
* required 3 seconds delay to let VBUS signal fully settle down
*/
mdelay(3000);
/* Enable VBUS power: Set output value of VBUS pin as enabled */
buf[0] |= (1 << I2C_IO_REG_0_USB_H_OFF);
ret = dm_i2c_write(dev, I2C_IO_DATA_OUT_REG_0, buf, 1);
if (ret) {
printf("Failed to set IO expander via I2C\n");
return -EIO;
}
mdelay(500); /* required delay to let output value settle */
return 0;
}
|
