blob: 1c60d4b83142e964c5899eaae7ba17d57d4028c2 (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
|
/*
* SDH Masks
*/
#ifndef __BFIN_PERIPHERAL_SDH__
#define __BFIN_PERIPHERAL_SDH__
/* Bit masks for SDH_COMMAND */
#define CMD_IDX 0x3f /* Command Index */
#define CMD_RSP 0x40 /* Response */
#define CMD_L_RSP 0x80 /* Long Response */
#define CMD_INT_E 0x100 /* Command Interrupt */
#define CMD_PEND_E 0x200 /* Command Pending */
#define CMD_E 0x400 /* Command Enable */
#ifdef RSI_BLKSZ
#define CMD_CRC_CHECK_D 0x800 /* CRC Check is disabled */
#define CMD_DATA0_BUSY 0x1000 /* Check Busy State on DATA0 */
#endif
/* Bit masks for SDH_PWR_CTL */
#ifndef RSI_BLKSZ
#define PWR_ON 0x3 /* Power On */
#define SD_CMD_OD 0x40 /* Open Drain Output */
#define ROD_CTL 0x80 /* Rod Control */
#endif
/* Bit masks for SDH_CLK_CTL */
#define CLKDIV 0xff /* MC_CLK Divisor */
#define CLK_E 0x100 /* MC_CLK Bus Clock Enable */
#define PWR_SV_E 0x200 /* Power Save Enable */
#define CLKDIV_BYPASS 0x400 /* Bypass Divisor */
#define BUS_MODE_MASK 0x1800 /* Bus Mode Mask */
#define STD_BUS_1 0x000 /* Standard Bus 1 bit mode */
#define WIDE_BUS_4 0x800 /* Wide Bus 4 bit mode */
#define BYTE_BUS_8 0x1000 /* Byte Bus 8 bit mode */
#ifdef RSI_BLKSZ
#define CARD_TYPE_MASK 0xe000 /* Card type mask */
#define CARD_TYPE_OFFSET 13 /* Card type offset */
#define CARD_TYPE_SDIO 0
#define CARD_TYPE_eMMC 1
#define CARD_TYPE_SD 2
#define CARD_TYPE_CEATA 3
#endif
/* Bit masks for SDH_RESP_CMD */
#define RESP_CMD 0x3f /* Response Command */
/* Bit masks for SDH_DATA_CTL */
#define DTX_E 0x1 /* Data Transfer Enable */
#define DTX_DIR 0x2 /* Data Transfer Direction */
#define DTX_MODE 0x4 /* Data Transfer Mode */
#define DTX_DMA_E 0x8 /* Data Transfer DMA Enable */
#ifndef RSI_BLKSZ
#define DTX_BLK_LGTH 0xf0 /* Data Transfer Block Length */
#else
/* Bit masks for SDH_BLK_SIZE */
#define DTX_BLK_LGTH 0x1fff /* Data Transfer Block Length */
#endif
/* Bit masks for SDH_STATUS */
#define CMD_CRC_FAIL 0x1 /* CMD CRC Fail */
#define DAT_CRC_FAIL 0x2 /* Data CRC Fail */
#define CMD_TIME_OUT 0x4 /* CMD Time Out */
#define DAT_TIME_OUT 0x8 /* Data Time Out */
#define TX_UNDERRUN 0x10 /* Transmit Underrun */
#define RX_OVERRUN 0x20 /* Receive Overrun */
#define CMD_RESP_END 0x40 /* CMD Response End */
#define CMD_SENT 0x80 /* CMD Sent */
#define DAT_END 0x100 /* Data End */
#define START_BIT_ERR 0x200 /* Start Bit Error */
#define DAT_BLK_END 0x400 /* Data Block End */
#define CMD_ACT 0x800 /* CMD Active */
#define TX_ACT 0x1000 /* Transmit Active */
#define RX_ACT 0x2000 /* Receive Active */
#define TX_FIFO_STAT 0x4000 /* Transmit FIFO Status */
#define RX_FIFO_STAT 0x8000 /* Receive FIFO Status */
#define TX_FIFO_FULL 0x10000 /* Transmit FIFO Full */
#define RX_FIFO_FULL 0x20000 /* Receive FIFO Full */
#define TX_FIFO_ZERO 0x40000 /* Transmit FIFO Empty */
#define RX_DAT_ZERO 0x80000 /* Receive FIFO Empty */
#define TX_DAT_RDY 0x100000 /* Transmit Data Available */
#define RX_FIFO_RDY 0x200000 /* Receive Data Available */
/* Bit masks for SDH_STATUS_CLR */
#define CMD_CRC_FAIL_STAT 0x1 /* CMD CRC Fail Status */
#define DAT_CRC_FAIL_STAT 0x2 /* Data CRC Fail Status */
#define CMD_TIMEOUT_STAT 0x4 /* CMD Time Out Status */
#define DAT_TIMEOUT_STAT 0x8 /* Data Time Out status */
#define TX_UNDERRUN_STAT 0x10 /* Transmit Underrun Status */
#define RX_OVERRUN_STAT 0x20 /* Receive Overrun Status */
#define CMD_RESP_END_STAT 0x40 /* CMD Response End Status */
#define CMD_SENT_STAT 0x80 /* CMD Sent Status */
#define DAT_END_STAT 0x100 /* Data End Status */
#define START_BIT_ERR_STAT 0x200 /* Start Bit Error Status */
#define DAT_BLK_END_STAT 0x400 /* Data Block End Status */
/* Bit masks for SDH_MASK0 */
#define CMD_CRC_FAIL_MASK 0x1 /* CMD CRC Fail Mask */
#define DAT_CRC_FAIL_MASK 0x2 /* Data CRC Fail Mask */
#define CMD_TIMEOUT_MASK 0x4 /* CMD Time Out Mask */
#define DAT_TIMEOUT_MASK 0x8 /* Data Time Out Mask */
#define TX_UNDERRUN_MASK 0x10 /* Transmit Underrun Mask */
#define RX_OVERRUN_MASK 0x20 /* Receive Overrun Mask */
#define CMD_RESP_END_MASK 0x40 /* CMD Response End Mask */
#define CMD_SENT_MASK 0x80 /* CMD Sent Mask */
#define DAT_END_MASK 0x100 /* Data End Mask */
#define START_BIT_ERR_MASK 0x200 /* Start Bit Error Mask */
#define DAT_BLK_END_MASK 0x400 /* Data Block End Mask */
#define CMD_ACT_MASK 0x800 /* CMD Active Mask */
#define TX_ACT_MASK 0x1000 /* Transmit Active Mask */
#define RX_ACT_MASK 0x2000 /* Receive Active Mask */
#define TX_FIFO_STAT_MASK 0x4000 /* Transmit FIFO Status Mask */
#define RX_FIFO_STAT_MASK 0x8000 /* Receive FIFO Status Mask */
#define TX_FIFO_FULL_MASK 0x10000 /* Transmit FIFO Full Mask */
#define RX_FIFO_FULL_MASK 0x20000 /* Receive FIFO Full Mask */
#define TX_FIFO_ZERO_MASK 0x40000 /* Transmit FIFO Empty Mask */
#define RX_DAT_ZERO_MASK 0x80000 /* Receive FIFO Empty Mask */
#define TX_DAT_RDY_MASK 0x100000 /* Transmit Data Available Mask */
#define RX_FIFO_RDY_MASK 0x200000 /* Receive Data Available Mask */
/* Bit masks for SDH_FIFO_CNT */
#define FIFO_COUNT 0x7fff /* FIFO Count */
/* Bit masks for SDH_E_STATUS */
#define SDIO_INT_DET 0x2 /* SDIO Int Detected */
#define SD_CARD_DET 0x10 /* SD Card Detect */
#define SD_CARD_BUSYMODE 0x80000000 /* Card is in Busy mode */
#define SD_CARD_SLPMODE 0x40000000 /* Card in Sleep Mode */
#define SD_CARD_READY 0x00020000 /* Card Ready */
/* Bit masks for SDH_E_MASK */
#define SDIO_MSK 0x2 /* Mask SDIO Int Detected */
#define SCD_MSK 0x10 /* Mask Card Detect */
/* Bit masks for SDH_CFG */
#define CLKS_EN 0x1 /* Clocks Enable */
#define SD4E 0x4 /* SDIO 4-Bit Enable */
#define MWE 0x8 /* Moving Window Enable */
#define SD_RST 0x10 /* SDMMC Reset */
#define PUP_SDDAT 0x20 /* Pull-up SD_DAT */
#define PUP_SDDAT3 0x40 /* Pull-up SD_DAT3 */
#ifndef RSI_BLKSZ
#define PD_SDDAT3 0x80 /* Pull-down SD_DAT3 */
#else
#define PWR_ON 0x600 /* Power On */
#define SD_CMD_OD 0x800 /* Open Drain Output */
#define BOOT_EN 0x1000 /* Boot Enable */
#define BOOT_MODE 0x2000 /* Alternate Boot Mode */
#define BOOT_ACK_EN 0x4000 /* Boot ACK is expected */
#endif
/* Bit masks for SDH_RD_WAIT_EN */
#define RWR 0x1 /* Read Wait Request */
#endif
|
