1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
|
/*
* Copyright (C) 2012-2015 Masahiro Yamada <yamada.masahiro@socionext.com>
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include <config.h>
#include <linux/linkage.h>
#include <linux/sizes.h>
#include <asm/system.h>
#include "ssc-regs.h"
ENTRY(lowlevel_init)
mov r8, lr @ persevere link reg across call
/*
* The UniPhier Boot ROM loads SPL code to the L2 cache.
* But CPUs can only do instruction fetch now because start.S has
* cleared C and M bits.
* First we need to turn on MMU and Dcache again to get back
* data access to L2.
*/
mrc p15, 0, r0, c1, c0, 0 @ SCTLR (System Control Register)
orr r0, r0, #(CR_C | CR_M) @ enable MMU and Dcache
mcr p15, 0, r0, c1, c0, 0
#ifdef CONFIG_DEBUG_LL
bl debug_ll_init
#endif
bl setup_init_ram @ RAM area for stack and page table
/*
* Now we are using the page table embedded in the Boot ROM.
* It is not handy since it is not a straight mapped table for sLD3.
* Also, the access to the external bus is prohibited. What we need
* to do next is to create a page table and switch over to it.
*/
bl create_page_table
bl __v7_flush_dcache_all
/* Disable MMU and Dcache before switching Page Table */
mrc p15, 0, r0, c1, c0, 0 @ SCTLR (System Control Register)
bic r0, r0, #(CR_C | CR_M) @ disable MMU and Dcache
mcr p15, 0, r0, c1, c0, 0
bl enable_mmu
mov lr, r8 @ restore link
mov pc, lr @ back to my caller
ENDPROC(lowlevel_init)
ENTRY(enable_mmu)
mrc p15, 0, r0, c2, c0, 2 @ TTBCR (Translation Table Base Control Register)
bic r0, r0, #0x37
orr r0, r0, #0x20 @ disable TTBR1
mcr p15, 0, r0, c2, c0, 2
orr r0, r12, #0x8 @ Outer Cacheability for table walks: WBWA
mcr p15, 0, r0, c2, c0, 0 @ TTBR0
mov r0, #0
mcr p15, 0, r0, c8, c7, 0 @ invalidate TLBs
mov r0, #-1 @ manager for all domains (No permission check)
mcr p15, 0, r0, c3, c0, 0 @ DACR (Domain Access Control Register)
dsb
isb
/*
* MMU on:
* TLBs was already invalidated in "../start.S"
* So, we don't need to invalidate it here.
*/
mrc p15, 0, r0, c1, c0, 0 @ SCTLR (System Control Register)
orr r0, r0, #(CR_C | CR_M) @ MMU and Dcache enable
mcr p15, 0, r0, c1, c0, 0
mov pc, lr
ENDPROC(enable_mmu)
/*
* For PH1-Pro4 or older SoCs, the size of WAY is 32KB.
* It is large enough for tmp RAM.
*/
#define BOOT_RAM_SIZE (SZ_32K)
#define BOOT_RAM_BASE ((CONFIG_SPL_STACK) - (BOOT_RAM_SIZE))
#define BOOT_WAY_BITS (0x00000100) /* way 8 */
ENTRY(setup_init_ram)
/*
* Touch to zero for the boot way
*/
0:
/*
* set SSCOQM, SSCOQAD, SSCOQSZ, SSCOQWN in this order
*/
ldr r0, = 0x00408006 @ touch to zero with address range
ldr r1, = SSCOQM
str r0, [r1]
ldr r0, = BOOT_RAM_BASE
ldr r1, = SSCOQAD
str r0, [r1]
ldr r0, = BOOT_RAM_SIZE
ldr r1, = SSCOQSZ
str r0, [r1]
ldr r0, = BOOT_WAY_BITS
ldr r1, = SSCOQWN
str r0, [r1]
ldr r1, = SSCOPPQSEF
ldr r0, [r1]
cmp r0, #0 @ check if the command is successfully set
bne 0b @ try again if an error occurs
ldr r1, = SSCOLPQS
1:
ldr r0, [r1]
cmp r0, #0x4
bne 1b @ wait until the operation is completed
str r0, [r1] @ clear the complete notification flag
mov pc, lr
ENDPROC(setup_init_ram)
#define DEVICE 0x00002002 /* Non-shareable Device */
#define NORMAL 0x0000000e /* Normal Memory Write-Back, No Write-Allocate */
ENTRY(create_page_table)
ldr r0, = DEVICE
ldr r1, = BOOT_RAM_BASE
mov r12, r1 @ r12 is preserved during D-cache flush
0: str r0, [r1], #4 @ specify all the sections as Device
adds r0, r0, #0x00100000
bcc 0b
ldr r0, = NORMAL
str r0, [r12] @ mark the first section as Normal
add r0, r0, #0x00100000
str r0, [r12, #4] @ mark the second section as Normal
mov pc, lr
ENDPROC(create_page_table)
|
