summaryrefslogtreecommitdiff
path: root/include/configs
Commit message (Collapse)AuthorAgeLines
* Merge branch 'master' of git://git.denx.de/u-boot-fsl-qoriqTom Rini2016-05-24-2/+37
|\
| * armv8: ls1043ardb: enable scsi command and pcie to sata converterPo Liu2016-05-18-0/+21
| | | | | | | | | | | | | | Enable scsi command and pcie to sata chip 88SE9170. Signed-off-by: Po Liu <po.liu@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
| * armv8: ls1043ardb: invert irq pin polarity for AQR105 PHYShaohui Xie2016-05-18-0/+1
| | | | | | | | | | | | | | | | | | To use AQR105 PHY's interrupt, we need to invert the IRQ pin polarity by setting relative bit in SCFG_INTPCR register, because AQR105 interrupt is low active but GIC accepts high active. Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
| * armv8: ls1043a: copy kernel from QSPI when booting with QSPI enabledQianyu Gong2016-05-18-0/+5
| | | | | | | | | | | | | | | | | | IFC won't be initialized in U-Boot if QSPI is enabled on LS1043AQDS. So this patch could fix 'sync abort' caused by autoboot that tries to access IFC address. Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
| * armv8: ls2080a: update eth primePrabhakar Kushwaha2016-05-18-2/+2
| | | | | | | | | | | | | | | | As per new PHY framework, DPNI naming convetion is no more used. Use new naming convention. Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
| * armv8: ls2080: enable sec_init in U-BootAneesh Bansal2016-05-18-0/+8
| | | | | | | | | | | | | | | | Define CONFIG_FSL_CAAM for LS2080 which would enable call to sec_init() during U-Boot. Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
* | Merge branch 'master' of git://git.denx.de/u-boot-netTom Rini2016-05-24-0/+1
|\ \ | | | | | | | | | | | | | | | | | | Signed-off-by: Tom Rini <trini@konsulko.com> Conflicts: drivers/net/zynq_gem.c
| * | ti_omap5_common: eth: do not define DM_ETH for splMugunthan V N2016-05-24-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Since omap's spl doesn't support DM currently, do not define DM_ETH for spl build. Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
* | | Merge branch 'master' of git://www.denx.de/git/u-boot-microblazeTom Rini2016-05-24-7/+64
|\ \ \
| * | | ARM64: zynqmp: Add SPL support supportMichal Simek2016-05-24-2/+41
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Support RAM and MMC boot mode in SPL also with SPL_FIT images. In MMC boot mode two boot options are available: 1) Boot flow with ATF(EL3) and full U-Boot(EL2): aarch64-linux-gnu-objcopy -O binary bl31.elf bl31.bin mkimage -A arm64 -O linux -T kernel -C none -a 0xfffe5000 -e 0xfffe5000 -d bl31.bin atf.ub cp spl/boot.bin <sdcard fat partition> cp atf.ub <sdcard fat partition> cp u-boot.bin <sdcard fat partition> 2) Boot flow with full U-Boot(EL3): cp spl/boot.bin <sdcard> cp u-boot*.img <sdcard> 3) emmc boot mode dd if=/dev/zero of=sd.img bs=1024 count=1024 parted sd.img mktable msdos parted sd.img mkpart p fat32 0% 100% kpartx -a sd.img mkfs.vfat /dev/mapper/loop0p1 mount /dev/mapper/loop0p1 /mnt/ cp spl/boot.bin /mnt cp u-boot.img /mnt cp u-boot.bin /mnt cp atf.ub /mnt umount /dev/mapper/loop0p1 kpartx -d sd.img cp sd.img /tftpboot/ and program it via u-boot tftpb 10000 sd.img mmcinfo mmc write 10000 0 $filesize mmc rescan mmc part ls mmc 0 psu_init() function contains low level SoC setup generated for every HW design by Xilinx design tools. xil_io.h is only supporting file to fix all dependencies from tools. The same solution was used on Xilinx Zynq. The patch also change CONFIG_SYS_INIT_SP_ADDR to the end of OCM which stays at the same location all the time. Bootrom expects starting address to be at 0xfffc0000 that's why this address is SPL_TEXT_BASE. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
| * | | ARM64: zynqmp: Enable option to overwrite default variablesMichal Simek2016-05-24-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | Enable overwriting variables out of main config file. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
| * | | ARM64: zynqmp: Remove CONFIG_PREBOOTMichal Simek2016-05-24-1/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | CONFIG_PREBOOT variable is breaking ./test/py framework. Remove it. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
| * | | ARM64: zynqmp: Enable eMMC boot partitions commandsMichal Simek2016-05-24-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | Enable some additional features of the eMMC boot partitions. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
| * | | ARM64: zynqmp: Add support for reading MAC from eepromMichal Simek2016-05-24-0/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add support for on board eeprom with programmed MAC for using in u-boot to have uniq address for every board. Most of the time uniq MAC address is on a label on the board. If address is not programmed use these command to program it. On zcu102: ZynqMP> mm.b 0 00000000: 00 ? 00 00000001: a0 ? 0a 00000002: 35 ? 35 00000003: 02 ? 02 00000004: 00 ? ef 00000005: 00 ? 67 00000006: 00 ? q i2c dev 5 i2c write 0 54 20 6 i2c md 54 20 Signed-off-by: Michal Simek <michal.simek@xilinx.com>
| * | | ARM64: zynqmp: Enable missing distro default optionsMichal Simek2016-05-24-0/+14
| | | | | | | | | | | | | | | | | | | | | | | | Enable all options which distros requires. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
| * | | ARM: zynq: load u-boot.img whether CONFIG_OF_SEPARATE is defined or notMasahiro Yamada2016-05-24-5/+1
| |/ / | | | | | | | | | | | | | | | | | | | | | | | | Since commit ad1ecd2063da ("fdt: Build a U-Boot binary without device tree"), u-boot-dtb.img is identical to u-boot.img, so SPL can always load u-boot.img whether CONFIG_OF_SEPARATE is defined or not. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* | | Merge branch 'master' of git://git.denx.de/u-boot-atmelTom Rini2016-05-24-0/+155
|\ \ \
| * | | board: atmel: add SAMA5D2 PTC Engineering boardWenyou Yang2016-05-24-0/+155
| |/ / | | | | | | | | | | | | | | | | | | | | | | | | | | | The board supports following features: - Boot media support: NAND Flash/SPI Flash - Support ethernet - Support USB mass storage Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
* | | Merge branch 'master' of git://git.denx.de/u-boot-x86Tom Rini2016-05-23-3/+8
|\ \ \ | |/ / |/| |
| * | x86: minnowmax: Adjust U-Boot environment address in SPI flashBin Meng2016-05-23-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Currently U-Boot environment address is at offset 0x7fe00 of a 8MB SPI flash. When creating a partial u-boot.rom image without flash descriptor and ME firmware, U-Boot actually occupies the last 1MB of the flash, and reprograming U-Boot causes previous environment settings get lost which is not convenient during testing. Adjust the environment address to 0x6ef000 instead (before the MRC cache data region in the flash). Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Stefan Roese <sr@denx.de> Reviewed-by: Simon Glass <sjg@chromium.org>
| * | x86: Remove acpi=off boot parameter when ACPI is onBin Meng2016-05-23-2/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Remove the kernel boot parameter acpi=off so that kernel can turn on ACPI support. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Stefan Roese <sr@denx.de> Tested-by: Stefan Roese <sr@denx.de> Reviewed-by: Simon Glass <sjg@chromium.org>
* | | Merge branch 'master' of git://git.denx.de/u-boot-mipsTom Rini2016-05-23-0/+277
|\ \ \
| * | | mips: ath79: Add support for TPLink WDR4300Marek Vasut2016-05-21-0/+93
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add support for the TPLink WDR4300 router, which is based on the AR9344 MIPS 74Kc CPU and has 128 MiB of RAM. The USB is supported on this system as well. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com> Cc: Wills Wang <wills.wang@live.com>
| * | | mips: ath79: add AP143 reference boardWills Wang2016-05-21-0/+90
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch add board-level code and base DT for AP143. Signed-off-by: Wills Wang <wills.wang@live.com> [updated defconfig, enabled CONFIG_USE_PRIVATE_LIBGCC=y] Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
| * | | mips: ath79: add AP121 reference boardWills Wang2016-05-21-0/+86
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch add board-level code and base DT for AP121. Signed-off-by: Wills Wang <wills.wang@live.com> [updated defconfig, enabled CONFIG_USE_PRIVATE_LIBGCC=y] Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
| * | | Use CONFIG_IDE_SWAP_IO when running on big-endian MIPS (32 or 64-bit) in ↵Stanislav Galabov2016-05-21-0/+8
| |/ / | | | | | | | | | | | | | | | QEMU so that IDE transfers work properly Signed-off-by: Stanislav Galabov <sgalabov@gmail.com>
* | | arm: cm-t43: add support for eeprom layout comandsNikita Kiryanov2016-05-20-0/+11
| | | | | | | | | | | | | | | | | | | | | | | | Add support for EEPROM and EEPROM layout commands for CM-T43. Cc: Igor Grinberg <grinberg@compulab.co.il> Cc: Tom Rini <trini@konsulko.com> Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
* | | arm: cm-t35: add support for eeprom layout comandsNikita Kiryanov2016-05-20-0/+11
| | | | | | | | | | | | | | | | | | | | | | | | Add support for EEPROM and EEPROM layout commands for CM-T35. Cc: Igor Grinberg <grinberg@compulab.co.il> Cc: Tom Rini <trini@konsulko.com> Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
* | | arm: cm-t3517: add support for eeprom layout comandsNikita Kiryanov2016-05-20-0/+11
| | | | | | | | | | | | | | | | | | | | | | | | Add support for EEPROM and EEPROM layout commands for CM-T3517. Cc: Igor Grinberg <grinberg@compulab.co.il> Cc: Tom Rini <trini@konsulko.com> Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
* | | arm: cm-t54: add support for eeprom layout comandsNikita Kiryanov2016-05-20-0/+11
| | | | | | | | | | | | | | | | | | | | | | | | Add support for EEPROM and EEPROM layout commands for CM-T54. Cc: Igor Grinberg <grinberg@compulab.co.il> Cc: Tom Rini <trini@konsulko.com> Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
* | | arm: cm-t335: add support for eeprom layout comandsNikita Kiryanov2016-05-20-0/+11
| | | | | | | | | | | | | | | | | | | | | | | | Add support for EEPROM and EEPROM layout commands for CM-T335. Cc: Igor Grinberg <grinberg@compulab.co.il> Cc: Tom Rini <trini@konsulko.com> Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
* | | arm: cm-fx6: add support for eeprom layout comandsNikita Kiryanov2016-05-20-0/+11
| | | | | | | | | | | | | | | | | | | | | | | | Add support for EEPROM and EEPROM layout commands for CM-FX6. Cc: Igor Grinberg <grinberg@compulab.co.il> Cc: Tom Rini <trini@konsulko.com> Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
* | | arm: mvebu: theadorable: Enable CONFIG_ZERO_BOOTDELAY_CHECKStefan Roese2016-05-20-0/+1
|/ / | | | | | | | | | | | | Enable bootdelay 0 check so that booting can be interrupted even with bootdelay configured to 0. Signed-off-by: Stefan Roese <sr@denx.de>
* | Merge git://git.denx.de/u-boot-dmTom Rini2016-05-17-24/+45
|\ \
| * | dm: sandbox: mmc: Enable building MMC code for sandboxSimon Glass2016-05-17-0/+2
| | | | | | | | | | | | | | | | | | | | | Enable building the MMC code for sandbox. This increases build coverage for sandbox. Signed-off-by: Simon Glass <sjg@chromium.org>
| * | dm: sandbox: Enable systemaceSimon Glass2016-05-17-0/+4
| | | | | | | | | | | | | | | | | | | | | Enable building the systemace code for sandbox. This increases build coverage for sandbox. Signed-off-by: Simon Glass <sjg@chromium.org>
| * | dm: sandbox: Enable SATASimon Glass2016-05-17-0/+3
| | | | | | | | | | | | | | | | | | | | | Enable building the SATA code for sandbox. This increases build coverage for sandbox. Signed-off-by: Simon Glass <sjg@chromium.org>
| * | dm: sandbox: Enable SCSISimon Glass2016-05-17-0/+6
| | | | | | | | | | | | | | | | | | | | | Enable building the SCSI code for sandbox. This increases build coverage for sandbox. Signed-off-by: Simon Glass <sjg@chromium.org>
| * | dm: sandbox: Enable IDESimon Glass2016-05-17-0/+10
| | | | | | | | | | | | | | | | | | | | | Enable building the IDE code for sandbox. This is for build coverage only. It does not currently work. Signed-off-by: Simon Glass <sjg@chromium.org>
| * | dm: scsi: Rename CONFIG_CMD_SCSI to CONFIG_SCSISimon Glass2016-05-17-20/+20
| | | | | | | | | | | | | | | | | | | | | | | | This option currently enables both the command and the SCSI functionality. Rename the existing option to CONFIG_SCSI since most of the code relates to the feature. Signed-off-by: Simon Glass <sjg@chromium.org>
| * | pci: Drop CONFIG_SYS_SCSI_SCAN_BUS_REVERSESimon Glass2016-05-17-4/+0
| |/ | | | | | | | | | | | | This option is not used by any board. Drop it. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
* | Merge branch 'master' of git://www.denx.de/git/u-boot-imxTom Rini2016-05-17-2/+5
|\ \
| * | ARM: mx6: Enable MMC and SATA extfs boot supportMarek Vasut2016-05-17-2/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Enable support for booting U-Boot image from ext filesystem when either SD/MMC or SATA support is compiled into the SPL. This will allow easy transition from loading U-Boot image from ad-hoc offset on the card to loading U-Boot image from the filesystem. VFAT support is intently not enabled. The boot order is tweaked so that raw is tested first and if the raw has no signature, FS boot is attempted. To install just the SPL on i.MX6 board, perform the following operation $ dd if=SPL of=/dev/sdX seek=2 bs=512 To install the U-Boot image, copy u-boot.img to the first partition of the SD/MMC/SATA drive. The partition must be formated to extfs. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Fabio Estevam <fabio.estevam@nxp.com> Cc: Peng Fan <van.freenix@gmail.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Tom Rini <trini@konsulko.com>
| * | ARM: mx6: Enable STDIO deregistering on NovenaMarek Vasut2016-05-17-0/+1
| |/ | | | | | | | | | | | | | | Novena supports USB keyboard, which is a pluggable device and can be unplugged. Thus, we need to be able to deregister it's stdio device. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de>
* | i2c: config: Move SYS_I2C_DW to KconfigStefan Roese2016-05-17-4/+0
|/ | | | | | | | | This patch moves all appearances of CONFIG_SYS_I2C_DW from the config header to the defconfig files. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Heiko Schocher <hs@denx.de> Cc: Alexey Brodkin <abrodkin@synopsys.com>
* Fix various typos, scattered over the code.Robert P. J. Day2016-05-05-3/+3
| | | | | | | | | | | | | Spelling corrections for (among other things): * environment * override * variable * ftd (should be "fdt", for flattened device tree) * embedded * FTDI * emulation * controller
* omap4: duovero: Disable EFI bootingAsh Charles2016-05-05-0/+1
| | | | | | | | The DuoVero board fails to compile with EFI enabled as the generated binaries are too large. As this platform doesn't currently need EFI, disable this feature. Signed-off-by: Ash Charles <ashcharles@gmail.com>
* omap4: load files for legacy bootAsh Charles2016-05-05-1/+4
| | | | | | | Be sure to load the zImage and fdtfile prior to actually booting in case we are doing a legacy boot. Signed-off-by: Ash Charles <ashcharles@gmail.com>
* include/configs: Numerous typo fixes: "controler" -> "controller".Robert P. J. Day2016-05-03-82/+82
| | | | Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
* igep00x0: Use the SRAM available for SPL.Enric Balletbo i Serra2016-05-03-0/+7
| | | | | | | | | | | Move CONFIG_SPL_TEXT_BASE down to 0x40200000 and set CONFIG_SPL_MAX_SIZE to (SRAM_SCRATCH_SPACE_ADDR - CONFIG_SPL_TEXT_BASE), so that it's clear what the limit is. This will also help some compilers to fit all the code into the allocated space. Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
generated by cgit v1.1 at 2024-11-09 06:18:27 +0000