summaryrefslogtreecommitdiff
path: root/include/configs
Commit message (Collapse)AuthorAgeLines
* mpc83xx: don't disable autobootKim Phillips2008-09-24-3/+3
| | | | | | | | | | bootdelay set to -1 'permanently' disables autobooting, even if bootcmd is specified. Change to a positive value to allow autobooting when a bootcmd is set. Reported-by: Coray Tate <Coray.Tate@freescale.com> Cc: Scott Wood <scottwood@freescale.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* mpc83xx: add h/w flash protection to board configsKim Phillips2008-09-24-0/+9
| | | | | | | | the operating system may leave flash in a h/w locked state after writing. This allows u-boot to continue to write flash by enabling h/w unlocking by default. Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* socrates: change default mtest address rangeAnatolij Gustschin2008-09-22-2/+2
| | | | | | | | Running mtest command on socrates without specifying an address range crashes the board. This patch changes default mtest address range to prevent this behavior. Signed-off-by: Anatolij Gustschin <agust@denx.de>
* socrates: fix SPD EEPROM addressAnatolij Gustschin2008-09-22-1/+1
| | | | | | | | | Commit be0bd8234b9777ecd63c4c686f72af070d886517 changed SPD EEPROM address to 0x51 and DDR SDRAM detection stopped working. Change this address back to 0x50. Signed-off-by: Anatolij Gustschin <agust@denx.de>
* ADS5121: fix typo in "rootpath" default settingWolfgang Denk2008-09-18-1/+1
| | | | Signed-off-by: Wolfgang Denk <wd@denx.de>
* TQM8xx: Fix CFI flash driver support for all TQM8xx based boardsWolfgang Denk2008-09-16-10/+43
| | | | | | | | | | After switching to using the CFI flash driver, the correct remapping of the flash banks was forgotten. Also, some boards were not adapted, and the old legacy flash driver was not removed yet. Signed-off-by: Wolfgang Denk <wd@denx.de>
* 85xx: socrates: Add support for new image format.u-boot@bugs.denx.de2008-09-13-0/+5
| | | | Signed-off-by: Detlev Zundel <dzu@denx.de>
* Merge branch 'Makefile-next' of git://git.denx.de/u-boot-armWolfgang Denk2008-09-12-2651/+2650
|\
| * ap325rxa: remove duplicate CONFIG_FLASH_CFI_DRIVERJean-Christophe PLAGNIOL-VILLARD2008-09-10-1/+0
| | | | | | | | Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
| * rename CFG_ENV macros to CONFIG_ENVJean-Christophe PLAGNIOL-VILLARD2008-09-10-1906/+1906
| | | | | | | | Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
| * rename CFG_ENV_IS_IN_FLASH in CONFIG_ENV_IS_IN_FLASHJean-Christophe PLAGNIOL-VILLARD2008-09-10-458/+458
| | | | | | | | Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
| * cleanup use of CFG_ENV_IS_IN_FLASHJean-Christophe PLAGNIOL-VILLARD2008-09-10-5/+5
| | | | | | | | | | | | | | | | - #if CFG_ENV_IS_IN_FLASH - #if (CFG_ENV_IS_IN_FLASH == 1) - #define CFG_ENV_IS_IN_FLASH 0 Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
| * rename CFG_ENV_IS_NOWHERE in CONFIG_ENV_IS_NOWHEREJean-Christophe PLAGNIOL-VILLARD2008-09-10-52/+52
| | | | | | | | Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
| * rename CFG_ENV_IS_IN_SPI_FLASH in CONFIG_ENV_IS_IN_SPI_FLASHJean-Christophe PLAGNIOL-VILLARD2008-09-10-2/+2
| | | | | | | | Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
| * rename CFG_ENV_IS_IN_ONENAND in CONFIG_ENV_IS_IN_ONENANDJean-Christophe PLAGNIOL-VILLARD2008-09-10-1/+1
| | | | | | | | Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
| * rename CFG_ENV_IS_IN_NVRAM in CONFIG_ENV_IS_IN_NVRAMJean-Christophe PLAGNIOL-VILLARD2008-09-10-80/+80
| | | | | | | | Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
| * rename CFG_ENV_IS_IN_NAND in CONFIG_ENV_IS_IN_NANDJean-Christophe PLAGNIOL-VILLARD2008-09-10-25/+25
| | | | | | | | Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
| * rename CFG_ENV_IS_IN_DATAFLASH in CONFIG_ENV_IS_IN_DATAFLASHJean-Christophe PLAGNIOL-VILLARD2008-09-10-13/+13
| | | | | | | | Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
| * rename CFG_ENV_IS_IN_EEPROM in CONFIG_ENV_IS_IN_EEPROMJean-Christophe PLAGNIOL-VILLARD2008-09-10-110/+110
| | | | | | | | Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
| * cmd_mac: Move conditional compilation to MakefileJean-Christophe PLAGNIOL-VILLARD2008-09-10-5/+5
| | | | | | | | | | | | | | finish remaning CFG_ID_EEPROM in CONFIG_ID_EEPROM start in commit ad8f8687b78c3e917b173f038926695383c55555 Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
* | Merge branch 'master' of git://git.denx.de/u-boot-ppc4xxWolfgang Denk2008-09-12-1/+6
|\ \
| * | ppc4xx: Enable device tree (FDT) support in zeus board portStefan Roese2008-09-12-0/+6
| | | | | | | | | | | | Signed-off-by: Stefan Roese <sr@denx.de>
| * | ppc4xx: Fix SDRAM inititialization of multiple 405 based board portsStefan Roese2008-09-12-1/+0
| |/ | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch fixes a problem introdiced with patch bbeff30c [ppc4xx: Remove superfluous dram_init() call or replace it by initdram()]. The boards affected are: - PCI405 - PPChameleonEVB - quad100hd - taihu - zeus Signed-off-by: Stefan Roese <sr@denx.de>
* | ARM OMAP : Correct Invalid Timer Register Field Declaration in omap1510.h & ↵Gururaja Hebbar K R2008-09-12-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | omap730.h - Correct Invalid #define of MPUTIM_PTV_MASK for omap1510 & omap730 register definition MPUTIM_PTV_MASK is defined as #define MPUTIM_PTV_MASK (0x7<<PTV_BIT) while it should have been #define MPUTIM_PTV_MASK (0x7<<MPUTIM_PTV_BIT) - Below Patch corrects the same Signed-off-by: Gururaja Hebbar <gururajakr@sanyo.co.in>
* | i.MX31: Make the SPI bus and chip select configurable for MC13783Magnus Lilja2008-09-12-0/+6
|/ | | | | | | | | | | The i.MX31 has three SPI buses and each bus has several chip selects and the MC13783 chip can be connected to any of these. The current RTC driver for MC13783 is hardcoded for CSPI2/SS2. This patch makes make MC13783 SPI bus and chip select configurable via CONFIG_MC13783_SPI_BUS and CONFIG_MC13783_SPI_CS. Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com>
* muas3001: update BR4 settingsHeiko Schocher2008-09-10-1/+1
| | | | | | Also set up the port pins for using I2C. Signed-off-by: Heiko Schocher <hs@denx.de>
* muas3001: added support for the LM75 sensor.Heiko Schocher2008-09-10-0/+10
| | | | Signed-off-by: Heiko Schocher <hs@denx.de>
* muas3001: activate WDT for the muas3001 board.Heiko Schocher2008-09-10-3/+17
| | | | Signed-off-by: Heiko Schocher <hs@denx.de>
* muas3001: added 64MB SDRAM autodetection.Heiko Schocher2008-09-10-5/+11
| | | | Signed-off-by: Heiko Schocher <hs@denx.de>
* Remove support for booting ARTOS imagesKumar Gala2008-09-09-8/+0
| | | | | | | | | | | Pantelis Antoniou stated: AFAIK, it is still used but the products using PPC are long gone. Nuke it plz (from orbit). So remove it since it cleans up a usage of env_get_char outside of the environment code. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* Moved conditional compile into MakefileAndreas Engel2008-09-09-3/+3
| | | | Signed-off-by: Andreas Engel <andreas.engel@ericsson.com>
* Update i386 code (sc520_cdp)Graeme Russ2008-09-09-0/+24
| | | | | | Attempt to bring i386 / sc520 inline with master Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
* 85xx: socrates: Enable Lime support.Anatolij Gustschin2008-09-09-0/+24
| | | | | | | | | This patch adds Lime GDC support together with support for the PWM backlight control through the w83782d chip. The reset pin of the latter is attached to GPIO, so we need to reset it in early_board_init_r. Signed-off-by: Anatolij Gustschin <agust@denx.de>
* 85xx: Socrates: Major code update.Detlev Zundel2008-09-09-43/+67
| | | | | | | | | | | | | | | | | - Update the local bus ranges in the FDT for Linux for the various devices connected to the local bus via chip-select. - Set the LCRR_DBYP bit in the LCRR for local bus frequencies lower than 66 MHz and uses I/O accessor functions consequently. - UPM data update. - Update of default environment and configuration. Use I2C multibus as we do have two I2C buses. Also enable sdram and ext2 commands. Signed-off-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: Sergei Poselenov <sposelenov@emcraft.com> Signed-off-by: Detlev Zundel <dzu@denx.de>
* Update Freescale 85xx boards to sys_eeprom.cTimur Tabi2008-09-09-6/+22
| | | | | | | | | The new sys_eeprom.c supports both the old CCID EEPROM format and the new NXID format, and so it obsoletes board/freescale/common/cds_eeprom.c. Freescale 86xx boards already use sys_eeprom.c, so this patch migrates the remaining Freescale 85xx boards to use it as well. cds_eeprom.c is deleted. Signed-off-by: Timur Tabi <timur@freescale.com>
* stxxtc: remove empty CONFIG_SHOW_ACTIVITY functionsWolfgang Denk2008-09-09-1/+0
| | | | Signed-off-by: Wolfgang Denk <wd@denx.de>
* NETTA2: remove empty CONFIG_SHOW_ACTIVITY functionsWolfgang Denk2008-09-09-1/+0
| | | | Signed-off-by: Wolfgang Denk <wd@denx.de>
* Merge branch 'master' of /home/stefan/git/u-boot/u-bootStefan Roese2008-09-08-2/+3
|\
| * ap325rxa/favr-32-ezkit: Use CONFIG_FLASH_CFI_DRIVERJean-Christophe PLAGNIOL-VILLARD2008-09-07-2/+2
| | | | | | | | Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
| * USB EHCI: reset root hubYuri Tikhonov2008-09-06-0/+1
| | | | | | | | | | | | | | | | | | | | | | Some of multi-function USB controllers (e.g. ISP1562) allow root hub resetting only via EHCI registers. So, this patch adds the corresponding kind of reset to OHCI's hc_reset() if the newly introduced CONFIG_PCI_EHCI_DEVNO option is set (e.g. for Socrates board). Signed-off-by: Yuri Tikhonov <yur@emcraft.com> Acked-by: Markus Klotzbuecher <mk@denx.de>
* | ppc4xx: Update CPCI405(AB) configurationMatthias Fuchs2008-09-08-0/+12
| | | | | | | | | | | | | | | | This patch add FDT support and command line editing capabilities for CPCI405 and CPCI405AB boards. Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com> Signed-off-by: Stefan Roese <sr@denx.de>
* | ppc4xx: Remove CONFIG_CS8952_PHY defineStefan Roese2008-09-08-1/+0
| | | | | | | | | | | | | | | | Since this define is only used on one board that was never really in production, removing this compile time option doesn't hurt and makes the code more readable. Signed-off-by: Stefan Roese <sr@denx.de>
* | ppc4xx: Update Kilauea to use PPC4xx DDR autocalibration routinesAdam Graham2008-09-05-0/+19
| | | | | | | | | | Signed-off-by: Adam Graham <agraham@amcc.com> Signed-off-by: Stefan Roese <sr@denx.de>
* | ppc44x: Unification of virtex5 pp440 boardsRicardo Ribalda Delgado2008-09-05-82/+213
|/ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch provides an unificated way of handling xilinx v5 ppc440 boards. It unificates 3 different things: 1) Source code A new board called ppc440-generic has been created. This board includes a generic tlb initialization (Maps the whole memory into virtual) and defines board_pre_init, checkboard, initdram and get_sys_info weakly, so, they can be replaced by specific functions. If a new board needs to redefine any of the previous functions (specific initialization) it can create a new directory with the specific initializations needed. (see the example ml507 board). 2) Configuration file Common configurations are located under configs/xilinx-ppc440.h, this header file interpretes the xparameters file generated by EDK and configurates u-boot in correspondence. Example: if there is a Temac, allows CMD_CONFIG_NET Specific configuration are located under specific configuration file. (see the example ml507 board) 3) Makefile Some work has been done in order to not duplicate work in the Main Makefile. Please see the attached code. In order to support new boards they can be implemented in the next way: a) Simple Generic Board (90% of the time) Using EDK generates a new xparameters.h file, replace ppc440-generic/xparameters.h and run make xilinx-ppc440-generic_config && make b) Simple Boards with special u-boot parameters (9 % of the time) Create a new file under configs for it (use ml507.h as example) and change your paramaters. Create a new Makefile paragraph and compile c) Complex boards (1% of the time) Create a new folder for the board, like the ml507 Finally, it adds support for the Avnet FX30T Evaluation board, following the new generic structure: Cheap board by Avnet for evaluating the Virtex5 FX technology. This patch adds support for: - UartLite - 16MB Flash - 64MB RAM Prior using U-boot in this board, read carefully the ERRATA by Avnet to solve some memory initialization issues. Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@uam.es> Signed-off-by: Stefan Roese <sr@denx.de>
* Merge branch 'master' of git://git.denx.de/u-boot-ppc4xxWolfgang Denk2008-09-03-131/+109
|\ | | | | | | | | | | | | | | Conflicts: board/esd/dasa_sim/dasa_sim.c Signed-off-by: Wolfgang Denk <wd@denx.de>
| * ppc4xx: Update VOM405 board configurationMatthias Fuchs2008-09-03-43/+9
| | | | | | | | | | | | | | | | | | - remove PCI code - add command line editing - minor cleanup Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com> Signed-off-by: Stefan Roese <sr@denx.de>
| * ppc4xx: Add fdt support for VOM405 boardsMatthias Fuchs2008-09-03-0/+2
| | | | | | | | | | Signed-off-by: Matthias Fuchs <mf@esd.eu> Signed-off-by: Stefan Roese <sr@denx.de>
| * ppc4xx: Coding style cleanupMatthias Fuchs2008-09-03-83/+79
| | | | | | | | | | | | | | Wrap long lines etc. Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com> Signed-off-by: Stefan Roese <sr@denx.de>
| * ppc4xx: Enable USB on PLU405 boardsMatthias Fuchs2008-09-03-4/+16
| | | | | | | | | | | | | | | | | | | | This patch enables the PCI-OHCI controller on PLU405 board. Also the default CPU frequency is updated to 266 MHz and command line editing is enabled. Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com> Signed-off-by: Stefan Roese <sr@denx.de>
| * ppc4xx: Add fdt support for PLU405 boardsMatthias Fuchs2008-09-03-0/+2
| | | | | | | | | | Signed-off-by: Matthias Fuchs <mf@esd.eu> Signed-off-by: Stefan Roese <sr@denx.de>
generated by cgit v1.1 at 2024-11-07 20:09:07 +0000