summaryrefslogtreecommitdiff
path: root/board/freescale
Commit message (Collapse)AuthorAgeLines
* ARMv8/ls1043ardb: Integrate FSL PPAHou Zhiqiang2016-07-19-1/+7
| | | | | | | | | The PPA use PSCI to make secondary cores bootup. So when PPA was enabled, add the CONFIG_ARMV8_PSCI to identify the SMP boot-method between PSCI and spin-table. Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
* armv8: Move secure_ram variable out of generic global dataYork Sun2016-07-15-35/+40
| | | | | | | Secure_ram variable was put in generic global data. But only ARMv8 uses this variable. Move it to ARM specific data structure. Signed-off-by: York Sun <york.sun@nxp.com>
* armv8: ls1043aqds: use configurable clockQianyu Gong2016-06-28-0/+4
| | | | | | | Get the clocks from FPGA through I2C, if IFC is disabled. Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
* armv8: ls1043aqds: fix to get boot device info from FPGAQianyu Gong2016-06-24-5/+3
| | | | | | | | The LBMAP switches on the board will tell which boot device is used. Only QSPI boot is supported if the boot device is IFCCard. Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
* Merge branch 'master' of git://git.denx.de/u-boot-usbTom Rini2016-06-18-0/+4
|\ | | | | | | | | | | | | Signed-off-by: Tom Rini <trini@konsulko.com> Conflicts: arch/arm/include/asm/arch-fsl-layerscape/immap_lsch3.h
| * usb: xhci: fsl: Add workaround for USB erratum A008751Sriram Dash2016-06-13-0/+4
| | | | | | | | | | | | | | | | | | This patch is doing the following: 1. Implementing the errata for LS2080. 2. Adding fixup for fdt for LS2080. Signed-off-by: Sriram Dash <sriram.dash@nxp.com> Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
* | Merge branch 'master' of git://www.denx.de/git/u-boot-imxTom Rini2016-06-18-8/+20
|\ \
| * | imx: mx6ulevk: change QSPI PAD DSE to 120ohmPeng Fan2016-06-18-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The current pad DSE for QSPI is 60ohm. This setting cause too strong drive to clock and data signals. Need to change the DSE to 120ohm for better signal quality. Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <fabio.estevam@nxp.com> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
| * | imx6ulevk: fix LCD_nPWREN settingPeng Fan2016-06-18-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Q901 is PMOS, LCD_nPWREN should be at low voltage then output is 3V3. If LCD_nPWREN is high, output is 2.4V which is not correct. Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <fabio.estevam@nxp.com> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
| * | imx6ulevk: fix 74LV OE usagePeng Fan2016-06-18-3/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Fix 74LV OE gpio index. gpio index is wrong, so gpio output will not have effect, since we use wrong GPIO5_IO18, but not correct GPIO5_IO8. And at the end of the initialization of 74lv init, should keep OE voltage level at LOW to make 74lv output the correct voltage. Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <fabio.estevam@nxp.com> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
| * | mx7dsabresd: Fix LCD_PWR_EN output settingYe Li2016-06-18-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | LCD_PWR_EN controls the G pin of Q13 PMOS which needs low voltage to connect D to S for outputting LCD 3.3V. If LCD_PWR_EN is high, we measured the LCD 3v3 is actually 1.2V. Signed-off-by: Ye Li <ye.li@nxp.com> Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <fabio.estevam@nxp.com> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
| * | mx6sabresd: Allow LVDS backlight to be functional after a kernel rebootMarco Franchi2016-06-18-2/+16
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Currently the LVDS backlight does not work in U-Boot after a “reboot” comand in the kernel. This problem occurs because the kernel uses this pin in PWM mode and U-Boot does not configure the backlight pin as GPIO functionality. So fix the problem by explicitly configuring the backlight pin as GPIO in U-Boot. Signed-off-by: Marco Franchi <marco.franchi@nxp.com> Acked-by: Stefano Babic <sbabic@denx.de> Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
| * | Merge branch 'master' of git://git.denx.de/u-bootStefano Babic2016-06-18-465/+1280
| |\ \ | | |/ | | | | | | Signed-off-by: Stefano Babic <sbabic@denx.de>
* | | armv8: s32v234: Introduce basic support for s32v234evbEddy Petrișor2016-06-13-0/+735
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add initial support for NXP's S32V234 SoC and S32V234EVB board. The S32V230 family is designed to support computation-intensive applications for image processing. The S32V234, as part of the S32V230 family, is a high-performance automotive processor designed to support safe computation-intensive applications in the area of vision and sensor fusion. Code originally writen by: Original-signed-off-by: Stoica Cosmin-Stefan <cosminstefan.stoica@freescale.com> Original-signed-off-by: Mihaela Martinas <Mihaela.Martinas@freescale.com> Original-signed-off-by: Eddy Petrișor <eddy.petrisor@gmail.com> Signed-off-by: Eddy Petrișor <eddy.petrisor@nxp.com>
* | | Merge branch 'master' of git://www.denx.de/git/u-boot-imxTom Rini2016-06-12-45/+12
|\ \ \ | |/ /
| * | cosmetic: mx6slevk: Minor coding-style fixSebastien Bourdelin2016-05-31-8/+8
| | | | | | | | | | | | | | | | | | Fix the brace indentation in board_mmc_init(). Signed-off-by: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com>
| * | imx: mx6qsabreauto: drop duplicated net phy configurationPeng Fan2016-05-31-33/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | In 'commit d584c68ce0f5bf2f430ccfb2ba00bd506206fb91', ar8031 is changed to use ar8035_config. ar8035_config actually does the same thing as mx6_rgmii_rework, so drop mx6_rgmii_rework and board_phy_config. Signed-off-by: Peng Fan <van.freenix@gmail.com> Cc: Fabio Estevam <fabio.estevam@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com> Acked-by: Stefano Babic <sbabic@denx.de>
| * | board: mx6sabresd/auto: use simpler runtime cpu dection macrosPeng Fan2016-05-24-4/+4
| | | | | | | | | | | | | | | | | | | | | | | | Use simpler runtime cpu dection macros. Signed-off-by: Peng Fan <van.freenix@gmail.com> Cc: Fabio Estevam <fabio.estevam@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
* | | armv8: ls2080aqds: Enable QSPI boot supportYuan Yao2016-06-10-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds QSPI boot support for LS2080AQDS board. The QSPI boot image need to be programmed into the QSPI flash first. Then we can switch to booting from QSPI memory space. Signed-off-by: Yuan Yao <yao.yuan@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
* | | armv8: ls2080aqds: Config QSPI pin mux via FPGA in NAND bootYuan Yao2016-06-10-0/+9
| | | | | | | | | | | | | | | Signed-off-by: Yuan Yao <yao.yuan@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
* | | armv8: ls2080aqds: disable IFC NOR & QIXIS when QSPI enableYuan Yao2016-06-10-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | When QSPI is enabled, NOR flash and QIXIS can't be accessed through IFC due to pin mux. Enable I2C QIXIS access and I2C early init to read the sysclk and ddrclk. Signed-off-by: Yuan Yao <yao.yuan@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
* | | armv8: ls2080aqds: Select QSPI CLK div via SCFGYuan Yao2016-06-10-0/+5
| | | | | | | | | | | | | | | | | | | | | QSPI module output SCLK divisor value is configured through SCFG. Signed-off-by: Yuan Yao <yao.yuan@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
* | | board: ls2080a: Add "mcinitcmd" env for MC & DPL deploymentPratiyush Mohan Srivastava2016-06-10-0/+10
| |/ |/| | | | | | | | | | | | | | | | | | | | | Environment variable mcinitcmd is defined to initiate MC and DPL deployment from the location where it is stored (NOR, NAND, SD, SATA, USB) during booting. If this variable is not defined then macro MC_BOOT_ENV_VAR will be null and MC will not be booted and DPL will not be applied during U-boot booting. Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@nxp.com> Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
* | Merge branch 'master' of git://git.denx.de/u-boot-mpc85xxTom Rini2016-06-04-93/+77
|\ \
| * | freescale: Tweak various Makefiles to remove redundancy, fix aestheticsRobert P. J. Day2016-06-03-65/+46
| | | | | | | | | | | | | | | | | | | | | | | | No intended functional change, just remove redundancies in some Makefiles, and make whitespace aesthetics uniform. Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca> Reviewed-by: York Sun <york.sun@nxp.com>
| * | board/freescale: Use unified setup_ddr_tlbs for spl boot and non-spl bootShengzhou Liu2016-06-03-28/+19
| | | | | | | | | | | | | | | | | | | | | | | | We should use unified setup_ddr_tlbs() for spl boot and non-spl boot to make sure 'M' bit is set for DDR TLB to maintain cache coherence. Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
| * | powerpc/board: SPL: Enable malloc flag in global data.Sumit Garg2016-06-03-0/+12
| | | | | | | | | | | | | | | | | | | | | | | | For malloc to work in SPL framework enable GD_FLG_FULL_MALLOC_INIT flag in global data after allocating memory using mem_malloc_init. Signed-off-by: Sumit Garg <sumit.garg@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
* | | Merge git://git.denx.de/u-boot-nand-flashTom Rini2016-06-04-2/+2
|\ \ \
| * | | mtd: nand: Add+use mtd_to/from_nand and nand_get/set_controller_dataScott Wood2016-06-03-2/+2
| |/ / | | | | | | | | | | | | | | | | | | | | | | | | These functions are part of the Linux 4.6 sync. They are being added before the main sync patch in order to make it easier to address the issue across all NAND drivers (many/most of which do not closely track their Linux counterparts) separately from other merge issues. Signed-off-by: Scott Wood <oss@buserror.net>
* | | armv8: ls1012a: Add support of ls1012afrdm boardPrabhakar Kushwaha2016-06-03-0/+278
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | QorIQ LS1012A FREEDOM (LS1012AFRDM) is a high-performance development platform, with a complete debugging environment. The LS1012AFRDM board supports the QorIQ LS1012A processor and is optimized to support the high-bandwidth DDR3L memory and a full complement of high-speed SerDes ports. Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com> Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com> Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@nxp.com> Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
* | | armv8: ls1012a: Add support of ls1012ardb boardPrabhakar Kushwaha2016-06-03-0/+306
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | QorIQ LS1012A Reference Design System (LS1012ARDB) is a high-performance development platform, with a complete debugging environment. The LS1012ARDB board supports the QorIQ LS1012A processor and is optimized to support the high-bandwidth DDR3L memory and a full complement of high-speed SerDes ports. Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com> Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@nxp.com> Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
* | | armv8: ls1012a: Add support of ls1012aqds boardPrabhakar Kushwaha2016-06-03-0/+356
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | QorIQ LS1012A Development System (LS1012AQDS) is a high-performance development platform, with a complete debugging environment. The LS1012AQDS board supports the QorIQ LS1012A processor and is optimized to support the high-bandwidth DDR3L memory and a full complement of high-speed SerDes ports. Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com> Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@nxp.com> Signed-off-by: Abhimanyu Saini <abhimanyu.saini@nxp.com> Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
* | | board: freescale: common: Add flag for LBMAP brdcfg reg offsetAbhimanyu Saini2016-06-03-2/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add QIXIS_LBMAP_BRDCFG_REG to the save offset of LBMAP configuration register instead of hardcoding it in set_lbmap() function. Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com> Signed-off-by: Abhimanyu Saini <abhimanyu.saini@nxp.com> Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
* | | board: freescale: common: Conditionally compile IFC QXIS funcAbhimanyu Saini2016-06-03-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Check if qixis supports memory-mapped read/write before compiling IFC based qixis read/write functions. Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com> Signed-off-by: Abhimanyu Saini <abhimanyu.saini@nxp.com> Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
* | | armv8: fsl-layerscape: Organize SoC overview at common locationPrabhakar Kushwaha2016-06-03-154/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | SoC overviews are getting repeated across board folders. So, Organize SoC overview at common location i.e. fsl-layerscape/doc Also move README.lsch2 and README.lsch3 in same folder. Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
* | | armv8: ls1043aqds: fix usb PWRFAULT settingShaohui Xie2016-06-03-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | SCFG_USBPWRFAULT_DEDICATED instead of SCFG_USBPWRFAULT_SHARED should be used for USB 3 & 2. Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
* | | board: ls2080ardb: qds: Fix compiling issue when FSL_MC_ENET not definedYork Sun2016-06-03-0/+8
| | | | | | | | | | | | | | | | | | | | | U-Boot should continue to work without management complex (MC). Fix compiling errors and warnings. Signed-off-by: York Sun <york.sun@nxp.com>
* | | board: ls102xa: Fix ICID setupVincent Siles2016-06-03-2/+5
| | | | | | | | | | | | | | | | | | | | | LS102A ref manual dictates that ICID have to be written to the MSB of the ICID register, not to the LSB. Signed-off-by: Vincent Siles <vincent.siles@provenrun.com>
* | | board/freescale: Update ddr clk_adjustShengzhou Liu2016-06-03-172/+172
|/ / | | | | | | | | | | | | | | | | This patch updates clk_adjust to actual value for boards with T-series and LS-series SoCs to match the setting of clk_adjust in latest ddr driver. Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
* | Delete tests of CONFIG_OF_LIBFDT when testing CONFIG_OF_BOARD_SETUPRobert P. J. Day2016-05-27-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Since CONFIG_OF_BOARD_SETUP depends on CONFIG_OF_LIBFDT: config OF_BOARD_SETUP bool "Set up board-specific details in device tree before boot" depends on OF_LIBFDT ... remove superfluous tests of CONFIG_OF_LIBFDT when testing for CONFIG_OF_BOARD_SETUP. Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca> [trini: Typo fix: s/ifdefi/ifdef/] Signed-off-by: Tom Rini <trini@konsulko.com>
* | Merge branch 'master' of git://git.denx.de/u-boot-mpc85xxTom Rini2016-05-25-2/+7
|\ \
| * | powerpc:t4240rdb: Disable the non-existent ethernet ports on T4240RDBYing Zhang2016-05-24-0/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | Disable the non-existent ethernet ports on T4240RDB:FM1_DTSEC5, FM1_DTSEC6, FM2_DTSEC5 and FM2_DTSEC6. Signed-off-by: Ying Zhang <ying.zhang22455@nxp.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: York Sun <york.sun@nxp.com>
| * | powerpc/t208xrdb: Update MAINTAINERS fileYork Sun2016-05-19-1/+1
| | | | | | | | | | | | | | | Signed-off-by: York Sun <york.sun@nxp.com> CC: Shengzhou Liu <Shengzhou.Liu@nxp.com>
| * | powerpc/t208xqds: Update MAINTAINERS fileYork Sun2016-05-19-1/+1
| |/ | | | | | | | | Signed-off-by: York Sun <york.sun@nxp.com> CC: Shengzhou Liu <Shengzhou.Liu@nxp.com>
* | armv8: ls1043ardb: invert irq pin polarity for AQR105 PHYShaohui Xie2016-05-18-0/+4
| | | | | | | | | | | | | | | | | | To use AQR105 PHY's interrupt, we need to invert the IRQ pin polarity by setting relative bit in SCFG_INTPCR register, because AQR105 interrupt is low active but GIC accepts high active. Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
* | arch/arm, arch/powerpc: add # of SEC engines on the SOCAlex Porosanu2016-05-18-1/+1
| | | | | | | | | | | | | | | | | | | | Some SOCs, specifically the ones in the C29x familiy can have multiple security engines. This patch adds a system configuration define which indicates the maximum number of SEC engines that can be found on a SoC. Signed-off-by: Alex Porosanu <alexandru.porosanu@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
* | armv8: ls1043ardb: fix types of variablesQianyu Gong2016-05-18-3/+3
| | | | | | | | | | | | | | Using u16 for cfg_rcw_src and u8 for sd1refclk_sel is enough. Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
* | armv8: ls1043a: remove redundant code in board filesQianyu Gong2016-05-18-9/+0
| | | | | | | | | | | | | | | | | | gd->env_addr will be initialized in env_init() in common/env_nowhere.c if CONFIG_ENV_IS_NOWHERE is defined. So no need to do it again. Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
* | armv8/ls1043ardb: fix the limitation of using 'cpld reset'Qianyu Gong2016-05-18-2/+25
| | | | | | | | | | | | | | | | | | | | The current 'cpld reset' will just write global_rst register but couldn't switch to NOR boot if the board's switches are for NAND/SD boot. So need to write rcw source registers for NOR boot as well. Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
* | arm: uniform usage of u32 in ls102x caam configVincent Siles2016-05-18-1/+1
| | | | | | | | | | | | | | Mix usage of uint32_t and u32 fixed in favor of u32. Signed-off-by: Vincent Siles <vincent.siles@provenrun.com> Reviewed-by: York Sun <york.sun@nxp.com>
generated by cgit v1.1 at 2024-11-20 09:38:16 +0000