summaryrefslogtreecommitdiff
path: root/board/freescale/mx7d_12x12_ddr3_arm2
Commit message (Collapse)AuthorAgeLines
* MLK-11675 ARM: imx: change the VDD_SOC normal voltage to 0.975VBai Ping2015-10-13-0/+6
| | | | | | | | | According to the latest datasheet(Rev. C Draft 1, 10/2015) of i.MX7D, change the VDD_SOC voltage to 0.95V in run mode, and add a 25mV margin to cover the IR drop and board tolerance. So setting VDD_SOC voltage to 0.975V. Signed-off-by: Bai Ping <b51503@freescale.com>
* MLK-11299 ARM: imx7d: initialize PMIC standby mode and voltageAnson Huang2015-08-03-0/+10
| | | | | | | Datasheet Rev-B defines standby voltage as 1V for i.MX7D, we add 25mV for board level IR drop. Signed-off-by: Anson Huang <b20788@freescale.com>
* MLK-11238 imx: mx7d fix usdhc pad settingsPeng Fan2015-07-13-5/+3
| | | | | | | | | | | | | | | | | | | To CD/VSELECT/RST, should use same pad settings with USDHC_PAD_CTRL, because default NO_PAD_CTRL's settings is 100K Pull-Down. But, we need pull-up for CD/VSELECT/RST. Also some board provides external pull-down/up, we'd better use internal pull-up for these pad settings. To mx7d_12x12_lpddr3_arm2: If no card plugged in, "mmc dev 1" will show "Card did not respond to voltage select". After apply this patch, it will show "MMC: no card present". To mx7dsabresd: Alougth without this patch, if no card plugged in sd1, still correct msg "MMC: no card present", anyway we'd better use pull-up. Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
* MLK-11216-2 imx: mx7d-ddr3 remove epdc qos settingsPeng Fan2015-07-03-24/+0
| | | | | | Remove epdc qos settings from plugin.S, since set_epdc_qos does same thing. Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
* MLK-11216-1 imx:mx7d_12x12_ddr3_arm2 add missed Kconfig filesPeng Fan2015-07-03-0/+15
| | | | | | Add missed Kconfig files for mx7d_12x12_ddr3_arm2 board. Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
* MLK-11134-2 imx: mx7d_12x12_ddr3_arm2 update spi nor codePeng Fan2015-06-19-0/+5
| | | | | | | We should use board_spi_cs_gpio and remove the GPIO from CONFIG_SF_DEFAULT_CS. Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
* MLK-11059 imx: HAB unable to support Encrypted boot for 4096-bit keysUlises Cardenas2015-06-16-1/+1
| | | | | | | | Abstracted the CSF size in imximage from a hardcoded value to a config setting CONFIG_CSF_SIZE. This configuration is only enabled for secure boot. Increased the size of the CSF default allocation to 0x4000. This size covers the event the worst case of 4906-bits keys.
* MLK-10936 imx: mx7d: Change to use bootrom_sw_info for getting boot deviceimx_3.14.38_6ul_engrYe.Li2015-05-20-8/+5
| | | | | | | | | | | | | | | | | | | | | On MX7D, boot rom can provide some boot information such as boot device, arm freq, axi freq, etc. (see the structure below) Offset Byte4 | Byte3 | Byte2 | Byte1 0x0 Reserved | Boot Device Type | Boot Device Instance | Reserved 0x4 ARM core frequency(in Hz) 0x8 AXI bus frequency(in Hz) 0x0C DDR frequency(in Hz) 0x10 GPT1 input clock frequency(in Hz) 0x14 Reserved 0x18 0x1C The boot information can be accessed by get the pointer at 0x1E8. This patch changes the u-boot to use the new approach. When manufacture boot, the info recorded is the actual SD port, not the failed device. Signed-off-by: Ye.Li <B37916@freescale.com>
* MLK-10873-1 imx:mx7d use pmic frameworkPeng Fan2015-05-11-42/+26
| | | | | | Use pmic framework to simplify code and make code clean. Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
* MLK-10522-3: imx: mx7d_12x12_ddr3_arm2: add target board supportAdrian Alonso2015-04-29-0/+687
* Add mx7d_12x12_ddr3_arm2 target board support * Initial support for mx7d_12x12_ddr3_arm2 target board add support for base hardware eMMC, SD and ECSPI boot. Signed-off-by: Adrian Alonso <aalonso@freescale.com> Signed-off-by: Ye.Li <B37916@freescale.com> (cherry picked from commit 51d69f7996cc6e6da8bb3f0af751549cb2435e44) Conflicts: boards.cfg
generated by cgit v1.1 at 2024-12-06 02:58:52 +0000