summaryrefslogtreecommitdiff
path: root/arch/powerpc
Commit message (Collapse)AuthorAgeLines
* Handle most LDSCRIPT setting centrallyScott Wood2011-04-30-11/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Currently, some linker scripts are found by common code in config.mk. Some are found using CONFIG_SYS_LDSCRIPT, but the code for that is sometimes in arch config.mk and sometimes in board config.mk. Some are found using an arch-specific rule for looking in CPUDIR, etc. Further, the powerpc config.mk rule relied on CONFIG_NAND_SPL when it really wanted CONFIG_NAND_U_BOOT -- which covered up the fact that not all NAND_U_BOOT builds actually wanted CPUDIR/u-boot-nand.lds. Replace all of this -- except for a handful of boards that are actually selecting a linker script in a unique way -- with centralized ldscript finding. If board code specifies LDSCRIPT, that will be used. Otherwise, if CONFIG_SYS_LDSCRIPT is specified, that will be used. If neither of these are specified, then the central config.mk will check for the existence of the following, in order: $(TOPDIR)/board/$(BOARDDIR)/u-boot-nand.lds (only if CONFIG_NAND_U_BOOT) $(TOPDIR)/$(CPUDIR)/u-boot-nand.lds (only if CONFIG_NAND_U_BOOT) $(TOPDIR)/board/$(BOARDDIR)/u-boot.lds $(TOPDIR)/$(CPUDIR)/u-boot.lds Some boards (sc3, cm5200, munices) provided their own u-boot.lds that were dead code, because they were overridden by a CPUDIR u-boot.lds under the old powerpc rules. These boards' own u-boot.lds have bitrotted and no longer work -- these lds files have been removed. Signed-off-by: Scott Wood <scottwood@freescale.com> Tested-by: Graeme Russ <graeme.russ@gmail.com>
* mpc832x: add support for the mpc8321 based suvd3 boardHeiko Schocher2011-04-30-2/+3
| | | | | | | | | | | | | | | | | | | | - serial console on UART1 - Ethernet RMII over UCC4 - PHY SMSC LAN8700 - 64MB Flash - 128 MB DDR2 RAM - I2C - bootcount This board is similiar to the kmeter1 (8360) board, so common config options are extracted into the include/configs/km83xx-common.h file. Signed-off-by: Heiko Schocher <hs@denx.de> Acked-by: Kim Phillips <kim.phillips@freescale.com> cc: Kim Phillips <kim.phillips@freescale.com> cc: Holger Brunck <holger.brunck@keymile.com> cc: Valentin Longchamp <valentin.longchamp@keymile.com>
* powerpc: use 'video-mode' environment variable to configure DIUTimur Tabi2011-04-28-13/+3
| | | | | | | | | | | | | | | | Use the 'video-mode' environment variable (for Freescale chips that have a DIU display controller) to designate the full video configuration. Previously, the DIU driver used the 'monitor' variable, and it was used only to determine the output video port. The old definition of the "monitor" environment variable only determines which video port to use for output. This variable was set to a number (0, 1, or sometimes 2) to specify a DVI, LVDS, or Dual-LVDS port. The resolution was hard-coded into board-specific code. The Linux command-line arguments needed to be hard-coded to the proper video definition string. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Anatolij Gustschin <agust@denx.de>
* powerpc: fix implementation of out_8 to match the other out_XX functionsTimur Tabi2011-04-28-1/+4
| | | | Signed-off-by: Timur Tabi <timur@freescale.com>
* Merge branch 'master' of git://git.denx.de/u-boot-armWolfgang Denk2011-04-27-0/+4
|\
| * Don't grab memory for LCD if FB address is definedMinkyu Kang2011-04-27-0/+4
| | | | | | | | | | | | | | | | | | | | | | | | If FB address is defined specific address then don't grab memory for LCD Signed-off-by: Minkyu Kang <mk7.kang@samsung.com> Cc: Albert Aribaud <albert.aribaud@free.fr> Cc: Wolfgang Denk <wd@denx.de> Cc: Stefan Roese <sr@denx.de> Cc: Kim Phillips <kim.phillips@freescale.com> Cc: Andy Fleming <afleming@gmail.com> Cc: Kumar Gala <kumar.gala@freescale.com>
* | Respect memreserve regions specified in the device treeGrant Likely2011-04-25-0/+4
| | | | | | | | | | | | | | | | If a regions is reserved in the fdt, then it should not be used. Add the memreserve regions to the lmb so that u-boot doesn't use them to store the initrd. Signed-off-by: Grant Likely <grant.likely@linaro.org>
* | Remove device tree booting dependency on CONFIG_SYS_BOOTMAPSZGrant Likely2011-04-25-2/+2
| | | | | | | | | | | | | | | | | | The previous patch makes u-boot use the full accessible size of ram as the default boot mapped size if CONFIG_SYS_BOOTMAPSZ is not defined, which means boot_relocate_fdt() can be changed to depend solely on CONFIG_OF_LIBFDT. Signed-off-by: Grant Likely <grant.likely@linaro.org>
* | Default to bootm_size() when CONFIG_SYS_BOOTMAPSZ is not definedGrant Likely2011-04-25-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds a function getenv_bootm_mapsize() for obtaining the size of the early mapped region accessible by the kernel during early boot. It defaults to CONFIG_SYS_BOOTMAPSZ, or if not defined, defaults to getenv_bootm_size(), which in turn defaults to the size of RAM. getenv_bootm_mapsize() can also be overridden with a "bootm_mapsize" environmental variable. Signed-off-by: Grant Likely <grant.likely@linaro.org>
* | Stop passing around bootmem_base value.Grant Likely2011-04-25-6/+3
|/ | | | | | | | | | For the calls to boot_relocate_fdt(), boot_get_cmdline(), and boot_get_kbd(), the value of bootmem_base is always obtained by calling getenv_bootm_low(). Since the value always comes from the same source, the calling signature for those functions can be simplified by making them call getenv_bootm_low() directly. Signed-off-by: Grant Likely <grant.likely@linaro.org>
* Merge branch 'phylib' of git://git.denx.de/u-boot-mmcWolfgang Denk2011-04-20-35/+24
|\
| * fsl: Change fsl_phy_enet_if to phy_interface_tAndy Fleming2011-04-20-35/+5
| | | | | | | | | | | | | | | | | | | | | | | | The fsl_phy_enet_if enum was, essentially, the phy_interface_t enum. This meant that drivers which used fsl_phy_enet_if to deal with PHY interfaces would have to convert between the two (or we would have to have them mirror each other, and deal with the ensuing maintenance headache). Instead, we switch all clients of fsl_phy_enet_if over to phy_interface_t, which should become the standard, anyway. Signed-off-by: Andy Fleming <afleming@freescale.com> Acked-by: Detlev Zundel <dzu@denx.de>
| * tsec: Convert tsec to use PHY LibAndy Fleming2011-04-20-0/+19
| | | | | | | | | | | | | | | | | | | | | | | | | | This converts tsec to use the new PHY Lib. All of the old PHY support is ripped out. The old MDIO driver is split off, and placed in fsl_mdio.c. The initialization is modified to initialize the MDIO driver as well. The powerpc config file is modified to configure PHYLIB if TSEC_ENET is configured. Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Acked-by: Detlev Zundel <dzu@denx.de>
* | Revert "PowerPC: Add support for -msingle-pic-base"Wolfgang Denk2011-04-20-127/+12
|/ | | | | | | This reverts commit 39768f7715ed637ef02f49fc7de664cc1aaf14b3. Reson: it breaks a number of boards with embedded environment as the code size grows in some places.
* Make STANDALONE_LOAD_ADDR configurable per boardWolfgang Denk2011-04-12-1/+1
| | | | | | | | | | | | | Rename STANDALONE_LOAD_ADDR into CONFIG_STANDALONE_LOAD_ADDR and allow that the architecture-specific default value gets overwritten by defining the value in the board header file. Signed-off-by: Wolfgang Denk <wd@denx.de> Cc: Mike Frysinger <vapier@gentoo.org> Cc: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp> Cc: Daniel Hellstrom <daniel@gaisler.com> Cc: Tsi Chung Liew <tsi-chung.liew@freescale.com> Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
* PowerPC: Add support for -msingle-pic-baseJoakim Tjernlund2011-04-11-12/+127
| | | | | | | | | | | | | -msingle-pic-base is a new gcc option for ppc and it reduces the size of my u-boot with 6-8 KB. While at it, add -fno-jump-tables too to save a few more bytes. -msingle-pic-base will be in gcc 4.6, however backported patches are available at http://bugs.gentoo.org/show_bug.cgi?id=347281 Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
* PowerPC: Move -fPIC flag to common placeJoakim Tjernlund2011-04-11-13/+13
| | | | | | | | | | | | | | | | | | | | | | | | | | | The -fPIC flag belongs with -mrelocatable, move it there. Also change -fPIC to -fpic as this produces smaller binaries. However, currently -mrelocatable promotes -fpic to -fPIC, a fix for this is in upcoming gcc 4.6 or you can apply this small patch to gcc: diff --git a/gcc/config/rs6000/sysv4.h b/gcc/config/rs6000/sysv4.h index 8da8410..e4b8280 100644 --- a/gcc/config/rs6000/sysv4.h +++ b/gcc/config/rs6000/sysv4.h @@ -227,7 +227,8 @@ do { \ } \ \ else if (TARGET_RELOCATABLE) \ - flag_pic = 2; \ + if (!flag_pic) \ + flag_pic = 2; \ } while (0) #ifndef RS6000_BI_ARCH -- Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
* powerpc/85xx: Removed clearing of L2-as-SRAMFabian Cenedese2011-04-10-7/+0
| | | | | | | | Removed clearing of L2 cache as SRAM as it is not necessary without ECC. This also speeds up the booting process. Signed-off-by: Fabian Cenedese <cenedese@indel.ch> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* fsl_esdhc: Deal with watermark level register related changesPriyanka Jain2011-04-10-0/+2
| | | | | | | | | | | | | P1010 and P1014 has v2.3 version of FSL eSDHC controller in which watermark level register description has been changed: 9-15 bits represent WR_WML[0:6], Max value = 128 represented by 0x00 25-31 bits represent RD_WML[0:6], Max value = 128 represented by 0x00 Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com> Signed-off-by: Poonam Aggrwal <Poonam.Aggrwal@freescale.com> Tested-by: Stefano Babic <sbabic@denx.de> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/85xx: Add PBL boot from SPI flash support on P4080DSShaohui Xie2011-04-10-0/+19
| | | | | | | | | | | | | PBL(pre-boot loader): SPI flash used as RCW(Reset Configuration Word) and PBI(pre-boot initialization) source, CPC(CoreNet Platform Cache) used as 1M SRAM where PBL will copy whole U-BOOT image to, U-boot can boot from CPC after PBL completes RCW and PBI phases. Signed-off-by: Chunhe Lan <b25806@freescale.com> Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com> Signed-off-by: Shaohui Xie <b21989@freescale.com> Signed-off-by: Roy Zang <tie-fei.zang@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/85xx: Add support usb2/etsec and tdm/audio pin multiplex on P1022DSJiang Yutang2011-04-10-0/+10
| | | | | | | | | | | For soc which have pin multiplex relation, some of them can't enable simultaneously. This patch add environment var 'hwconfig' content defination for them. you can enable some one function by setting environment var 'hwconfig' content and reset board. Detail setting please refer doc/README.p1022ds Signed-off-by: Jiang Yutang <b14898@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* p4080ds: remove rev1-specific code for the SERDES8 erratumTimur Tabi2011-04-10-59/+47
| | | | | | | | Remove the SERDES8 erratum work-around code that only applied to P4080 rev1, which is not supported by this version of U-Boot. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/85xx: rename NAND prefixes to CONFIG_SYSMatthew McClintock2011-04-08-4/+4
| | | | | | | | | | renaming 85xx define CONFIG_NAND_OR_PRELIM to CONFIG_SYS_NAND_OR_PRELIM and CONFIG_NAND_BR_PRELIM to CONFIG_SYS_NAND_BR_PRELIM to use the more appropriate CONFIG_SYS prefix as well as be consistent with 83xx. Signed-off-by: Matthew McClintock <msm@freescale.com> cc: Scott Wood <scottwood@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/85xx: Add some defines & registers in immap_85xx.hZhao Chenhui2011-04-05-1/+6
| | | | | | | | | * Added SDHCDCR register to GUR struct * Added SDHCDCR_CD_INV define related to SDHCDCR * Added Pin Muxing define related to TDM on P102x Signed-off-by: Zhao Chenhui <b35336@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/85xx: Add P1021 specific QE and UEC supportHaiying Wang2011-04-05-10/+48
| | | | | | | | | | | | | | P1021 has some QE pins which need to be set in pmuxcr register before using QE functions. In this patch, pin QE0 and QE3 are set for UCC1 and UCC5 in Eth mode. QE9 and QE12 are set for MII management. QE12 needs to be released after MII access because QE12 pin is muxed with LBCTL signal. Also added relevant QE support defines unique to P1021. The P1021 QE is shared on P1012, P1016, and P1025. Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/85xx: don't init SDRAM when CONFIG_SYS_RAMBOOTZhao Chenhui2011-04-05-0/+12
| | | | | | Signed-off-by: Zhao Chenhui <b35336@freescale.com> Acked-by: Li Yang <leoli@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/8xxx: Fix typo for address hashing messageKumar Gala2011-04-04-1/+1
| | | | Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* mpc8xxx: DDR2/DDR3: Clean up DIMM-type switch statementsKyle Moffett2011-04-04-33/+33
| | | | | | | | | | | | | | | The numeric constants in the switch statements are replaced by #defines added to the common ddr_spd.h header. This dramatically improves the readability of the switch statments. In addition, a few of the longer lines were cleaned up, and the DDR2 type for an SO-RDIMM module was added to the DDR2 switch statement. Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com> Cc: Andy Fleming <afleming@gmail.com> Cc: Kim Phillips <kim.phillips@freescale.com> Acked-by: York Sun <yorksun@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* fsl_ddr: Don't use full 64-bit divides on 32-bit PowerPCKyle Moffett2011-04-04-16/+40
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | The current FreeScale MPC-8xxx DDR SPD interpreter is using full 64-bit integer divide operations to convert between nanoseconds and DDR clock cycles given arbitrary DDR clock frequencies. Since all of the inputs to this are 32-bit (nanoseconds, clock cycles, and DDR frequencies), we can easily restructure the computation to use the "do_div()" function to perform 64-bit/32-bit divide operations. On 64-bit this change is basically a no-op, because do_div is implemented as a literal 64-bit divide operation and the instruction scheduling works out almost the same. On 32-bit PowerPC a fully accurate 64/64 divide (__udivdi3 in libgcc) is over 1.1kB of code and thousands of heavily dependent cycles to compute, all of which is linked from libgcc. Another 1.2kB of code comes in for the function __umoddi3. It should be noted that nothing else in U-Boot or the Linux kernel seems to require a full 64-bit divide on my 32-bit PowerPC. Build-and-boot-tested on the HWW-1U-1A board using DDR2 SPD detection. Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com> Acked-by: York Sun <yorksun@freescale.com> Cc: Andy Fleming <afleming@gmail.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/85xx: Fix setting of LIODN prop in PCIe nodes on P3041/P5020Laurentiu TUDOR2011-04-04-16/+16
| | | | | | | | | | | | | We utilize the compatible string to find the node to add fsl,liodn property to. However P3041 & P5020 don't have "fsl,p4080-pcie" compatible for their PCIe controllers as they aren't backwards compatible. Allow the macro's to specify the PCIe compatible to use to allow SoC uniqueness. On P3041 & P5020 we utilize "fsl,qoriq-pcie-v2.2" for the PCIe controllers. Signed-off-by: Laurentiu TUDOR <Laurentiu.Tudor@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/85xx: Update timer-frequency prop in ptp_timer node of device treebhaskar upadhaya2011-04-04-0/+9
| | | | | | | | | | Fix up the device tree property associated with the IEEE 1588 timer source frequency. Currently we only support the IEEE 1588 timer source being the internal eTSEC system clock (for those SoCs with IEEE 1588 support). The eTSEC clock is ccb_clk/2. Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/85xx: Fix determining Fman freq on P1023Kumar Gala2011-04-04-4/+1
| | | | | | | | On the P1023 the Fman freq is equivalent to the system bus freq, not 1/2 of it. Also we only have one Fman so no need for the code to deal with a second. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/85xx: Fixup determining PME, FMan freqKumar Gala2011-04-04-9/+35
| | | | | | | | | | | | | | | | | | | | | | On CoreNet based SoCs (P2040, P3041, P4080, P5020) we have some additional rules to determining the various frequencies that PME & FMan IP blocks run at. We need to take into account: * Reduced number of Core Complex PLL clusters * HWA_ASYNC_DIV (allows for /2 or /4 options) On P2040/P3041/P5020 we only have 2 Core Complex PLLs and in such SoCs the PME & FMan blocks utilize the second Core Complex PLL. On SoCs like p4080 with 4 Core Complex PLLs we utilize the third Core Complex PLL for PME & FMan blocks. On P2040/P3041/P5020 we have the added feature that we can divide the PLL down further by either /2 or /4 based on HWA_ASYNC_DIV. On P4080 this options doesn't exist, however HWA_ASYNC_DIV field in RCW should be set to 0 and this gets a backward compatiable /2 behavior. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/85xx: Specify CONFIG_SYS_FM_MURAM_SIZEKumar Gala2011-04-04-0/+8
| | | | | | | CONFIG_SYS_FM_MURAM_SIZE varies from SoC to SoC to specify it in config_mpc85xx.h for those parts with a Frame Manager. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/85xx: Corrected sdhc clock value for P1010Priyanka Jain2011-04-04-1/+2
| | | | | | | | SDHC clock is equal to CCB on P1010 and P1014 not CCB/2. Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com> Signed-off-by: Poonam Aggrwal <Poonam.Aggrwal@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/85xx: Adds some P1010/P1014 SoC configuration definesPoonam Aggrwal2011-04-04-0/+8
| | | | | | | | Add defines for FSL_SATA_V2, # of DDR controllers, reset value of CCSRBAR and SDHC erratum. Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/85xx: Support for Freescale P1024/P1025 processorKumar Gala2011-04-04-0/+78
| | | | | | | | | | | | | | | | | | | | | Add Support for Freescale P1024/P1025 (dual core) and P1015/P1016 (single core) processors. P1024 is a variant of P1020 processor with a core frequency from 400Mhz to 667Mhz and comes in a 561-pin wirebond power-BGA P1025 is a variant of P1021 processor with a core frequency from 400Mhz to 667Mhz and comes in a 561-pin wirebond power-BGA P1015 is a variant of P1024 processor with single core and P1016 is a variant of P1025 processor with single core. Added comments in config_mpc85xx.h to denote single core versions of processors. Signed-off-by: Jin Qing <b24347@freescale.com> Signed-off-by: Li Yang <leoli@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/85xx: load ucode from nand flash before qe_initHaiying Wang2011-04-04-0/+17
| | | | | | | | In the case the QE's microcode is stored in nand flash, we need to load it from NAND flash to ddr first then the qe_init can get the ucode correctly. Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* fsl_ddr: Adds 16 bit DDR Data width optionPoonam Aggrwal2011-04-04-1/+4
| | | | | | Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Cc: York Sun <yorksun@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/8xxx: Display DIMM modelYork Sun2011-04-04-4/+7
| | | | | | | | Beside displaying RDIMM or UDIMM, this patch adds display of the model numbers embedded in SPD. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* fsl_pci: Add support for FSL PCIe controllers v2.xPrabhakar Kushwaha2011-04-04-4/+16
| | | | | | | | | | | | | | | | | | | | | | | FSL PCIe controller v2.1: - New MSI inbound window - Same Inbound windows address as PCIe controller v1.x Added new pit_t member(pmit) to struct ccsr_pci for MSI inbound window FSL PCIe controller v2.2 and v2.3: - Different addresses for PCIe inbound window 3,2,1 - Exposed PCIe inbound window 0 - New PCIe interrupt status register Added new Interrupt Status register to struct ccsr_pci & updated pit_t array size to reflect the 4 inbound windows. To maintain backward compatiblilty, on V2.2 or greater controllers we start with inbound window 1 and leave inbound 0 with its default value (which maps to CCSRBAR). Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/85xx: Refactor Qman/Portal support to be shared between SoCsHaiying Wang2011-04-04-22/+44
| | | | | | | | | | | | | | There are some differences between CoreNet (P2040, P3041, P5020, P4080) and and non-CoreNet (P1017, P1023) based SoCs in what features exist and the memory maps. * Rename various immap defines to remove _CORENET_ if they are shared * Added P1023/P1017 specific memory offsets * Only setup LIODNs or LIODN related code on CORENET based SoCs (features doesn't exist on P1023/P1017) Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/85xx: Add support for Freescale P1023/P1017 ProcessorsRoy Zang2011-04-04-1/+99
| | | | | | | | | | | | | Add P1023 (dual core) & P1017 (single core) specific information: * SERDES Table * Added P1023/P1017 to cpu_type_list and SVR list (fixed issue with P1013 not being sorted correctly). * Added P1023/P1027 to config_mpc85xx.h * Added new LAW type introduced on P1023/P1017 * Updated a few immap register/defines unique to P1023/P1017 Signed-off-by: Roy Zang <tie-fei.zang@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/85xx: Don't build read_tlbcam_entry for CONFIG_NAND_SPLKumar Gala2011-04-04-2/+2
| | | | | | Slim down NAND SPL build a bit as we don't need read_tlbcam_entry. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc: Add cpu_secondary_init_r to allow for initialization post env setupKumar Gala2011-04-04-6/+23
| | | | | | | | | | | | | We can simplify some cpu/SoC level initialization by moving it to be after the environment and non-volatile storage is setup as there might be dependancies on such things in various boot configurations. For example for FSL SoC's with QE if we boot from NAND we need it setup to extra the ucode image to initialize the QE. If we always do this after environment & non-volatile storage is working we can have the code be the same regardless of NOR, NAND, SPI, MMC boot. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/85xx: Cleanup some QE related definesKumar Gala2011-04-04-67/+37
| | | | | | | | | Move some processor specific QE defines into config_mpc85xx.h and use QE_MURAM_SIZE to cleanup some ifdef mess in the QE immap struct. Also fixed up some comment style issues in immap_qe.h Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/8xxx: Refactor fsl_ddr_get_spd into common code from boardKumar Gala2011-04-04-3/+60
| | | | | | | | | | | | | | Move fsl_ddr_get_spd into common mpc8xxx/ddr/main.c as most boards pretty much do the same thing. The only variations are in how many controllers or DIMMs per controller exist. To make this work we standardize on the names of the SPD_EEPROM_ADDRESS defines based on the use case of the board. We allow boards to override get_spd to either do board specific fixups to the SPD data or deal with any unique behavior of how the SPD eeproms are wired up. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/8xxx: Replace fsl_ddr_get_mem_data_rate with get_ddr_freq()Kumar Gala2011-04-04-6/+3
| | | | | | | | | | Every 85xx board implements fsl_ddr_get_mem_data_rate via get_ddr_freq() and every 86xx board uses get_bus_freq(). If implement get_ddr_freq() as a static inline to call get_bus_freq() we can remove fsl_ddr_get_mem_data_rate altogether and just call get_ddr_freq() directly. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc: Move cpu specific lmb reserve to arch_lmb_reserveKumar Gala2011-04-04-0/+5
| | | | | | | | We've been utilizing board_lmb_reserve to reserve the boot page for MP systems. We can just move this into arch_lmb_reserve for 85xx & 86xx systems rather than duplicating in each board port. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* powerpc/85xx: Add some defines for P2040, P3041, P5010, P5020Kumar Gala2011-04-04-0/+15
| | | | | | | Specify the number of DDR controllers, number of frame managers, number of 1g and 10g ports. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
generated by cgit v1.1 at 2024-11-06 07:13:32 +0000