summaryrefslogtreecommitdiff
path: root/arch/powerpc/include
Commit message (Collapse)AuthorAgeLines
...
* powerpc/mpc8xxx: Fix DDR driver handling quad-rank DIMMs and address calculationYork Sun2012-10-22-0/+2
| | | | | | | | | | | | | | | | | | | | | | | Fix handling quad-rank DIMMs in a system with two DIMM slots and first slot supports both dual-rank DIMM and quad-rank DIMM. For systems with quad-rank DIMM and double dual-rank DIMMs, cs_config registers need to be enabled to maintain proper ODT operation. The inactive CS should have bnds registers cleared. Fix the turnaround timing for systems with all chip-selects enabled. This wasn't an issue before because DDR was running lower than 1600MT/s with this interleaving mode. Fix DDR address calculation. It wasn't an issue until we have multiple controllers with each more than 4GB and interleaving is disabled. It also fixes the message of DDR: 2 GiB (DDR3, 64-bit, CL=0.5, ECC off) when debugging DDR and first DDR controller is disabled. With the fix, the first enabled controller information will be displayed. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/mpc8xxx: Update DDR registersYork Sun2012-10-22-0/+32
| | | | | | | | | | | | | | | | | | | | | | | | | | | | DDRC ver 4.7 adds DDR_SLOW bit in sdram_cfg_2 register. This bit needs to be set for speed lower than 1250MT/s. CDR1 and CDR2 are control driver registers. ODT termination valueis for IOs are defined. Starting from DDRC 4.7, the decoding of ODT for IOs is 000 -> Termsel off 001 -> 120 Ohm 010 -> 180 Ohm 011 -> 75 Ohm 100 -> 110 Ohm 101 -> 60 Ohm 110 -> 70 Ohm 111 -> 47 Ohm Add two write leveling registers. Each QDS now has its own write leveling start value. In case of zero value, the value of QDS0 will be used. These values are board-specific and are set in board files. Extend DDR register timing_cfg_1 to have 4 bits for each field. DDR control driver registers and write leveling registers are added to interactive debugging for easy access. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* fm/mEMAC: add mEMAC frame workRoy Zang2012-10-22-0/+290
| | | | | | | | | | | The multirate ethernet media access controller (mEMAC) interfaces to 10Gbps and below Ethernet/IEEE 802.3 networks via either RGMII/RMII interfaces or XAUI/XFI/SGMII/QSGMII using the high-speed SerDes interface. Signed-off-by: Sandeep Singh <Sandeep@freescale.com> Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: Roy Zang <tie-fei.zang@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/mpc85xx: Add B4860 and variant SoCsYork Sun2012-10-22-0/+40
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add support for Freescale B4860 and variant SoCs. Features of B4860 are (incomplete list): Six fully-programmable StarCore SC3900 FVP subsystems, divided into three clusters-each core runs up to 1.2 GHz, with an architecture highly optimized for wireless base station applications Four dual-thread e6500 Power Architecture processors organized in one cluster-each core runs up to 1.8 GHz Two DDR3/3L controllers for high-speed, industry-standard memory interface each runs at up to 1866.67 MHz MAPLE-B3 hardware acceleration-for forward error correction schemes including Turbo or Viterbi decoding, Turbo encoding and rate matching, MIMO MMSE equalization scheme, matrix operations, CRC insertion and check, DFT/iDFT and FFT/iFFT calculations, PUSCH/PDSCH acceleration, and UMTS chip rate acceleration CoreNet fabric that fully supports coherency using MESI protocol between the e6500 cores, SC3900 FVP cores, memories and external interfaces. CoreNet fabric interconnect runs at 667 MHz and supports coherent and non-coherent out of order transactions with prioritization and bandwidth allocation amongst CoreNet endpoints. Data Path Acceleration Architecture, which includes the following: Frame Manager (FMan), which supports in-line packet parsing and general classification to enable policing and QoS-based packet distribution Queue Manager (QMan) and Buffer Manager (BMan), which allow offloading of queue management, task management, load distribution, flow ordering, buffer management, and allocation tasks from the cores Security engine (SEC 5.3)-crypto-acceleration for protocols such as IPsec, SSL, and 802.16 RapidIO manager (RMAN) - Support SRIO types 8, 9, 10, and 11 (inbound and outbound). Supports types 5, 6 (outbound only) Large internal cache memory with snooping and stashing capabilities for bandwidth saving and high utilization of processor elements. The 9856-Kbyte internal memory space includes the following: 32 Kbyte L1 ICache per e6500/SC3900 core 32 Kbyte L1 DCache per e6500/SC3900 core 2048 Kbyte unified L2 cache for each SC3900 FVP cluster 2048 Kbyte unified L2 cache for the e6500 cluster Two 512 Kbyte shared L3 CoreNet platform caches (CPC) Sixteen 10-GHz SerDes lanes serving: Two Serial RapidIO interfaces. Each supports up to 4 lanes and a total of up to 8 lanes Up to 8-lanes Common Public Radio Interface (CPRI) controller for glue- less antenna connection Two 10-Gbit Ethernet controllers (10GEC) Six 1G/2.5-Gbit Ethernet controllers for network communications PCI Express controller Debug (Aurora) Two OCeaN DMAs Various system peripherals 182 32-bit timers Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Signed-off-by: Roy Zang <tie-fei.zang@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/mpc85xx: Add T4240 SoCYork Sun2012-10-22-2/+115
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add support for Freescale T4240 SoC. Feature of T4240 are (incomplete list): 12 dual-threaded e6500 cores built on Power Architecture® technology Arranged as clusters of four cores sharing a 2 MB L2 cache. Up to 1.8 GHz at 1.0 V with 64-bit ISA support (Power Architecture v2.06-compliant) Three levels of instruction: user, supervisor, and hypervisor 1.5 MB CoreNet Platform Cache (CPC) Hierarchical interconnect fabric CoreNet fabric supporting coherent and non-coherent transactions with prioritization and bandwidth allocation amongst CoreNet end-points 1.6 Tbps coherent read bandwidth Queue Manager (QMan) fabric supporting packet-level queue management and quality of service scheduling Three 64-bit DDR3/3L SDRAM memory controllers with ECC and interleaving support Memory prefetch engine (PMan) Data Path Acceleration Architecture (DPAA) incorporating acceleration for the following functions: Packet parsing, classification, and distribution (Frame Manager 1.1) Queue management for scheduling, packet sequencing, and congestion management (Queue Manager 1.1) Hardware buffer management for buffer allocation and de-allocation (BMan 1.1) Cryptography acceleration (SEC 5.0) at up to 40 Gbps RegEx Pattern Matching Acceleration (PME 2.1) at up to 10 Gbps Decompression/Compression Acceleration (DCE 1.0) at up to 20 Gbps DPAA chip-to-chip interconnect via RapidIO Message Manager (RMAN 1.0) 32 SerDes lanes at up to 10.3125 GHz Ethernet interfaces Up to four 10 Gbps Ethernet MACs Up to sixteen 1 Gbps Ethernet MACs Maximum configuration of 4 x 10 GE + 8 x 1 GE High-speed peripheral interfaces Four PCI Express 2.0/3.0 controllers Two Serial RapidIO 2.0 controllers/ports running at up to 5 GHz with Type 11 messaging and Type 9 data streaming support Interlaken look-aside interface for serial TCAM connection Additional peripheral interfaces Two serial ATA (SATA 2.0) controllers Two high-speed USB 2.0 controllers with integrated PHY Enhanced secure digital host controller (SD/MMC/eMMC) Enhanced serial peripheral interface (eSPI) Four I2C controllers Four 2-pin or two 4-pin UARTs Integrated Flash controller supporting NAND and NOR flash Two eight-channel DMA engines Support for hardware virtualization and partitioning enforcement QorIQ Platform's Trust Architecture 1.1 Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Andy Fleming <afleming@freescale.com> Signed-off-by: Roy Zang <tie-fei.zang@freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/mpc85xx: Add T4 device definitionsAndy Fleming2012-10-22-2/+48
| | | | | | | | | | | | | | | | | | | | The T4 has added devices to previous corenet implementations: * SEC has 3 more DECO units * New PMAN device * New DCE device This doesn't add full support for the new devices. Just some preliminary support. Move PMAN LIODN to upper half of register Despite having only one LIODN, the PMAN LIODN is stored in the upper half of the register. Re-use the 2-LIODN code and just set the LIODN as if the second one is 0. This results in the actual LIODN being written to the upper half of the register. Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/corenet2: Add SerDes for corenet2York Sun2012-10-22-0/+50
| | | | | | | | | | | | | | | | | | | | | Create new files to handle 2nd generation Chassis as the registers are organized differently. - Add SerDes protocol parsing and detection - Add support of 4 SerDes - Add CPRI protocol in fsl_serdes.h The Common Public Radio Interface (CPRI) is publicly available specification that standardizes the protocol interface between the radio equipment control (REC) and the radio equipment (RE) in wireless basestations. This allows interoperability of equipment from different vendors,and preserves the software investment made by wireless service providers. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> Signed-off-by: Roy Zang <tie-fei.zang@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/mpc85xx: Add RCW bits and registers for SerDes for corenet2York Sun2012-10-22-5/+93
| | | | | | | | Corenet 2nd generation Chassis has different RCW and registers for SerDes. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/e6500: Move QCSP registers for QMan v3York Sun2012-10-22-1/+12
| | | | | | | | The QCSP registers are expanded and moved from offset 0 to offset 0x1000 for SoCs with QMan v3. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/mpc85xx: expand SERDES reference clock select bitYork Sun2012-10-22-1/+2
| | | | | | | | | | | | | Expand the reference clock select to three bits 000: 100 MHz 001: 125 MHz 010: 156.25MHz 011: 150 MHz 100: 161.1328125 MHz All others reserved Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/mpc85xx: Fix core cluster PLL calculation for Chassis generation 2York Sun2012-10-22-16/+20
| | | | | | | | | | | | | | | | | | Corenet based SoCs have different core clocks starting from Chassis generation 2. Cores are organized into clusters. Each cluster has up to 4 cores sharing same clock, which can be chosen from one of three PLLs in the cluster group with one of the devisors /1, /2 or /4. Two clusters are put together as a cluster group. These two clusters share the PLLs but may have different divisor. For example, core 0~3 are in cluster 1. Core 4~7 are in cluster 2. Core 8~11 are in cluster 3 and so on. Cluster 1 and 2 are cluster group A. Cluster 3 and 4 are in cluster group B. Cluster group A has PLL1, PLL2, PLL3. Cluster group B has PLL4, PLL5. Core 0~3 may have PLL1/2, core 4~7 may have PLL2/2. Core 8~11 may have PLL4/1. PME and FMan blocks can take different PLLs, configured by RCW. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/mpc85xx: change RCW MEM_PLL_PLAT for Chassis generation 2York Sun2012-10-22-0/+7
| | | | | | | | Chassis generation 2 has different mask and shift. Use macro instead of magic numbers. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/mpc85xx: Enable L2 at the beginning of U-boot for E6500York Sun2012-10-22-0/+59
| | | | | | | | | | | | | Using E6500 L1 cache as initram requires L2 cache enabled. Add l2-cache cluster enabling. Setup stash id for L1 cache as (coreID) * 2 + 32 + 0 Setup stash id for L2 cache as (cluster) * 2 + 32 + 1 Stash id for L2 is only set for Chassis 2. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/DPAA: Fix compiling errorYork Sun2012-10-22-2/+0
| | | | | | | | FSL_HW_PORTAL_PME is used even when CONFIG_SYS_DPAA_PME is not defined. Remove the #ifdef. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/85xx: Add P5040 processor supportTimur Tabi2012-10-22-0/+46
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add support for the Freescale P5040 SOC, which is similar to the P5020. Features of the P5040 are: Four P5040 single-threaded e5500 cores built Up to 2.4 GHz with 64-bit ISA support Three levels of instruction: user, supervisor, hypervisor CoreNet platform cache (CPC) 2.0 MB configures as dual 1 MB blocks hierarchical interconnect fabric Two 64-bit DDR3/3L SDRAM memory controllers with ECC and interleaving support Up to 1600MT/s Memory pre-fetch engine DPAA incorporating acceleration for the following functions Packet parsing, classification, and distribution (FMAN) Queue management for scheduling, packet sequencing and congestion management (QMAN) Hardware buffer management for buffer allocation and de-allocation (BMAN) Cryptography acceleration (SEC 5.2) at up to 40 Gbps SerDes 20 lanes at up to 5 Gbps Supports SGMII, XAUI, PCIe rev1.1/2.0, SATA Ethernet interfaces Two 10 Gbps Ethernet MACs Ten 1 Gbps Ethernet MACs High-speed peripheral interfaces Two PCI Express 2.0/3.0 controllers Additional peripheral interfaces Two serial ATA (SATA 2.0) controllers Two high-speed USB 2.0 controllers with integrated PHY Enhanced secure digital host controller (SD/MMC/eMMC) Enhanced serial peripheral interface (eSPI) Two I2C controllers Four UARTs Integrated flash controller supporting NAND and NOR flash DMA Dual four channel Support for hardware virtualization and partitioning enforcement Extra privileged level for hypervisor support QorIQ Trust Architecture 1.1 Secure boot, secure debug, tamper detection, volatile key storage Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/85xx: define SRIO LIODN functions only if SRIO is definedTimur Tabi2012-10-22-1/+3
| | | | | | | | The P5040 does not have SRIO support, so there are no SRIO LIODNs. Therefore, the functions that set the SRIO LIODNs should not be compiled. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/85xx: introduce SET_PCI_LIODN_BASE, for setting PCI LIODNsLaurentiu Tudor2012-10-22-1/+8
| | | | | | | | | | | | The liodn for the new PCIE controller included in P5040DS is no longer set through a register in the guts register block but with one in the PCIE register block itself. Update the PCIE CCSR structure to add the new liodn register and add a new dedicated SET_PCI_LIODN_BASE macro that puts the liodn in the correct register. Signed-off-by: Laurentiu Tudor <Laurentiu.Tudor@freescale.com> Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc/srio: Workaround for srio erratrm a004034Liu Gang2012-10-22-0/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Erratum: A-004034 Affects: SRIO Description: During port initialization, the SRIO port performs lane synchronization (detecting valid symbols on a lane) and lane alignment (coordinating multiple lanes to receive valid data across lanes). Internal errors in lane synchronization and lane alignment may cause failure to achieve link initialization at the configured port width. An SRIO port configured as a 4x port may see one of these scenarios: 1. One or more lanes fails to achieve lane synchronization. Depending on which lanes fail, this may result in downtraining from 4x to 1x on lane 0, 4x to 1x on lane R (redundant lane). 2. The link may fail to achieve lane alignment as a 4x, even though all 4 lanes achieve lane synchronization, and downtrain to a 1x. An SRIO port configured as a 1x port may fail to complete port initialization (PnESCSR[PU] never deasserts) because of scenario 1. Impact: SRIO port may downtrain to 1x, or may fail to complete link initialization. Once a port completes link initialization successfully, it will operate normally. Signed-off-by: Liu Gang <Gang.Liu@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* P4080/esdhc: make the P4080 ESDHC13 errata workaround conditionalZang Roy-R619112012-10-22-1/+1
| | | | | | | | | | P4080 Rev3.0 fixes ESDHC13 errata, so update the code to make the workaround conditional. In formal release document, the errata number should be ESDHC13 instead of ESDHC136. Signed-off-by: Roy Zang <tie-fei.zang@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* mpc85xx: make gpio_direction_output respect valueChris Packham2012-10-22-1/+4
| | | | | | | | | | | | | | Users of familiar with the Linux gpiolib API expect that value parameter to gpio_direction_output reflects the initial state of the output pin. gpio_direction_output was always driving the output low, now it drives it high or low according to the value provided. Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz> Cc: Kyle Moffett <Kyle.D.Moffett@boeing.com> Cc: Andy Fleming <afleming@gmail.com> Cc: Peter Tyser <ptyser@xes-inc.com> Cc: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Andy Fleming <afleming@freescale.com>
* powerpc: Change bi_baudrate and global data baudrate to intSimon Glass2012-10-19-2/+2
| | | | | | | These don't need to be longs, so change them. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Rini <trini@ti.com>
* ppc4xx: Remove AP1000 board supportStefan Roese2012-10-15-7/+0
| | | | | | | | | As the board seems to be unmaintained for some time, lets remove the support in mainline completely. Signed-off-by: Stefan Roese <sr@denx.de> Cc: James MacAulay <james.macaulay@amirix.com> Acked-by: Marek Vasut <marex@denx.de>
* ppc4xx: Remove ML2 board supportStefan Roese2012-10-15-1/+1
| | | | | | | | | As the board seems to be unmaintained for some time, lets remove the support in mainline completely. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Peter De Schrijver <p2@mind.be> Acked-by: Marek Vasut <marex@denx.de>
* ppc4xx: Remove IOP480 supportStefan Roese2012-10-15-5/+1
| | | | | | | | | | Since the IOP480 (PPC401/3 variant from PLX) is only used on 2 boards that are not actively maintained, lets remove support for it completely. This way the ppc4xx code will get a bit cleaner. Signed-off-by: Stefan Roese <sr@denx.de> Acked-by: Matthias Fuchs <matthias.fuchs@esd.eu> Acked-by: Marek Vasut <marex@denx.de>
* Merge branch 'master' of git://git.denx.de/u-boot-mpc85xxTom Rini2012-09-25-141/+184
|\
| * Revert "powerpc: Fix declaration type for I/O functions"Andy Fleming2012-08-23-10/+10
| | | | | | | | This reverts commit 20959471b5d07fdeb8603b918d80385aa2954711.
| * powerpc/85xx: clear out TLB on bootScott Wood2012-08-23-0/+5
| | | | | | | | | | | | | | | | Instead of just shooting down the entry that covers CCSR, clear out every TLB entry that isn't the one that we're executing out of. Signed-off-by: Scott Wood <scottwood@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
| * powerpc/mpc8xxx: Move HWCONFIG_BUFFER_SIZE into config.hYork Sun2012-08-23-0/+4
| | | | | | | | | | | | | | | | | | | | Before proper environment is setup, we extract hwconfig and put it into a buffer with size HWCONFIG_BUFFER_SIZE. We need to enlarge the buffer to accommodate longer string. Since this macro is used in multiple files, we move it into arch/powerpc/include/asm/config.h. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
| * powerpc/mpc8xxx: Enable 3-way and 4-way DDR interleavingYork Sun2012-08-23-1/+21
| | | | | | | | | | | | | | | | Restructure DDR interleaving option to support 3 and 4 DDR controllers for 2-, 3- and 4-way interleaving. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
| * powerpc/mpc8xxx: Add fine timing support for DDR3York Sun2012-08-23-0/+1
| | | | | | | | | | | | | | | | When the DDR3 speed goes higher, we need to utilize fine offset from SPD. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
| * powerpc/mpc8xxx: fix core id for multicore bootingYork Sun2012-08-23-0/+6
| | | | | | | | | | | | | | | | | | | | For the cores with multiple threads, we need to figure out which physical core a thread belongs. To match the core ids, update PIR registers and spin tables. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Andy Fleming <afleming@freescale.com>
| * Added new ext fields to IFCKumar Gala2012-08-23-6/+12
| | | | | | | | | | | | | | | | | | | | In case more than 32 bit address is used, the EXT bit should be set. Need to fix up address map for IFC #CS for 4, also need to move # of IFC banks into config_mpc85xx.h Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
| * Add IFC offset for DPAA/Corenet platformsKumar Gala2012-08-23-0/+1
| | | | | | | | | | | | Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
| * Add e6500 processor detectionKumar Gala2012-08-23-0/+1
| | | | | | | | | | Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
| * powerpc/mpc8xxx: use topology registers to calculate number of coresYork Sun2012-08-23-0/+1
| | | | | | | | | | | | | | | | | | We have actual topology infomation to find out exactly which core is present. Calculate the number of cores if not specified. Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
| * powerpc/mpc8xxx: Add immap for topology and rcpm registersYork Sun2012-08-23-1/+87
| | | | | | | | | | | | Signed-off-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
| * powerpc/mpc85xx: Add IFC LAW target ID for FSL High-End SoCPrabhakar Kushwaha2012-08-23-0/+1
| | | | | | | | | | | | | | | | | | | | Freescale's High-End SoC are going to have Integrated Flash controller (IFC)'s support. So add IFC LAW target ID support for High-End SoC or corenet SoC. Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
| * powerpc/mpc85xx:Enable debugger support to missed e500v2 SoCPrabhakar Kushwaha2012-08-23-0/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Freescale's e500v1 and e500v2 cores (used in mpc85xx chips) have some restrictions on external debugging (JTAG). Need to define define CONFIG_SYS_PPC_E500_DEBUG_TLB to enable a temporary TLB entry to be used during boot to work around the limitations. Enable missed e500v2 SoC i.e. MPC8536, MPC8544, MPC8548 and MPC8572 for debug support. Signed-off-by: Radu Lazarescu <radu.lazarescu@freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Cc: Tang Yuantian <Yuantian.Tang@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
| * powerpc/fsl-corenet: work around erratum A004510Scott Wood2012-08-23-0/+16
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Erratum A004510 says that under certain load conditions, modified cache lines can be discarded, causing data corruption. To work around this, several CCSR and DCSR register updates need to be made in a careful manner, so that there is no other transaction in corenet when the update is made. The update is made from a locked cacheline, with a delay before to flush any previous activity, and a delay after to flush the CCSR/DCSR update. We can't use a readback because that would be another corenet transaction, which is not allowed. We lock the subsequent cacheline to prevent it from being fetched while we're executing the previous cacheline. It is filled with nops so that a branch doesn't cause us to fetch another cacheline. Ordinarily we are running in a cache-inhibited mapping at this point, so we temporarily change that. We make it guarded so that we should never see a speculative load, and we never do an explicit load. Thus, only the I-cache should ever fill from this mapping, and we flush/unlock it afterward. Thus we should avoid problems from any potential cache aliasing between inhibited and non-inhibited mappings. NOTE that if PAMU is used with this patch, it will need to use a dedicated LAW as described in the erratum. This is the responsibility of the OS that sets up PAMU. Signed-off-by: Scott Wood <scottwood@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
| * powerpc/fsl-corenet: remove dead variant symbolsScott Wood2012-08-23-66/+4
| | | | | | | | | | | | | | | | | | | | | | These are not supported as individual build targets, but instead are supported by another target. The dead p4040 defines in particular had bitrotted significantly. Signed-off-by: Scott Wood <scottwood@freescale.com> Acked-by: Kumar Gala <galak@kernel.crashing.org> Signed-off-by: Andy Fleming <afleming@freescale.com>
| * powerpc/85xx: remove support for the Freescale P3060Timur Tabi2012-08-23-21/+1
| | | | | | | | | | | | | | | | The P3060 was cancelled before it went into production, so there's no point in supporting it. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
| * powerpc/85xx: add support for FM2 DTSEC5Timur Tabi2012-08-23-0/+2
| | | | | | | | | | | | | | | | Unlike previous SOCs, the Freescale P5040 has a fifth DTSEC on the second Fman, so add the Fman and SerDes macros for that DTSEC. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
| * p1014rdb: set ddr bus width properly depending on SVRMatthew McClintock2012-08-23-0/+1
| | | | | | | | | | | | | | | | | | | | Currently, for NAND boot for the P1010/4RDB we hard code the DDR configuration. We can still dynamically set the DDR bus width in the nand spl so the P1010/4RDB boards can boot from the same u-boot image Signed-off-by: Matthew McClintock <msm@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
| * powerpc/mpc8xxx: Remove P1015 and P1016 from CPU listYork Sun2012-08-23-31/+1
| | | | | | | | | | | | | | | | P1015 is the same as P1011 and P1016 is the same as P1012 from software point of view. They have different packages but share SVRs. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
| * powerpc/corenet_ds: Get rid of the CONFIG_SRIOBOOT_SLAVE_PORTx macroLiu Gang2012-08-23-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When compile the slave image for boot from SRIO, no longer need to specify which SRIO port it will boot from. The code will get this information from RCW and then finishes corresponding configurations. This has the following advantages: 1. No longer need to rebuild an image when change the SRIO port for boot from SRIO, just rewrite the new RCW with selected port, then the code will get the port information by reading new RCW. 2. It will be easier to support other boot location options, for example, boot from PCIE. Signed-off-by: Liu Gang <Gang.Liu@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
| * powerpc/corenet_ds: Get rid of the SRIOBOOT_MASTER build targetLiu Gang2012-08-23-5/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Get rid of the SRIOBOOT_MASTER build target, and to support for serving as a SRIO boot master via environment variable. Set the environment variable "bootmaster" to "SRIO1" or "SRIO2" using the following command: setenv bootmaster SRIO1 saveenv The "bootmaster" will enable the function of the SRIO boot master, and this has the following advantages compared with SRIOBOOT_MASTER build configuration: 1. Reduce a build configuration item in boards.cfg file. No longer need to build a special image for master, just use a normal target image and set the "bootmaster" variable. 2. No longer need to rebuild an image when change the SRIO port for boot from SRIO, just set the corresponding value to "bootmaster" based on the using SRIO port. Signed-off-by: Liu Gang <Gang.Liu@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
| * powerpc/mpc85xx: Make NMG_CPU_A011 workaround conditionalYork Sun2012-08-23-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This erratum applies to the following SoCs: P4080 rev 1.0, 2.0, fixed in rev 3.0 P2041 rev 1.0, 1.1, fixed in rev 2.0 P3041 rev 1.0, 1.1, fixed in rev 2.0. Workaround for erratum NMG_CPU_A011 is enabled by default. This workaround may degrade performance. P4080 erratum CPU22 shares the same workaround. So it is always enabled for P4080. For other SoCs, it can be disabled by hwconfig with syntax: fsl_cpu_a011:disable Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
* | powerpc: re-add bi_ip_addr to bd_t structAnatolij Gustschin2012-09-02-0/+1
|/ | | | | | | | | | | | | | | | | Since commit 50a47d0523e8efebe912bef539a77ffd42116451 (net: punt bd->bi_ip_addr) booting old 2.4.x ppc kernels is broken due to changed offsets of the fields in struct bd_t. Offsets of the fields after removed bi_ip_addr are wrong, causing wrong bus clocks and console baudrate configurations and various other issues. Re-add the bi_ip_addr field to preserve backward compatibility with older ppc kernels. Setting bi_ip_addr in board.c is not really needed, grepping in the 2.4 linux tree shows that bi_ip_addr is not accessed there. Adding bi_ip_addr to struct bd_t for other arches isn't needed it seems. bd_t is not used by other arches in the 2.4 linux tree. Signed-off-by: Anatolij Gustschin <agust@denx.de> Acked-by: Wolfgang Denk <wd@denx.de>
* powerpc: Fix declaration type for I/O functionsPrabhakar Kushwaha2012-08-09-10/+10
| | | | | | | | | Prototype declaration of I/O operation functions are not correct. as both 'extern' and function definition are at same place. Chage protoype declaration as static. Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
* powerpc:Fix return type & parameter passed for I/O functionsPrabhakar Kushwaha2012-08-09-15/+15
| | | | | | | | | | | | Return type of in_8, in_be16 and in_le16 should not be'int'. Update it to type u8/u16/u32. Although 'unsigned' for in_be32 and in_le32 is correct. But to make return type uniform across the file changed to u32 Similarly, parameter passed to out_8, out_be16, out_le16 ,out_be32 & out_le32 should not be 'int'.Change it to type u8/u16/u32. Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
generated by cgit v1.1 at 2024-10-24 00:23:52 +0000