summaryrefslogtreecommitdiff
path: root/arch/arm/include
Commit message (Collapse)AuthorAgeLines
* arm: at91: add support for mini-box picosam9g45 boardErik van Luijk2015-08-21-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Bootlog: U-Boot SPL 2015.10-rc1-00452-g96a7ed1 (Aug 17 2015 - 10:32:21) mci: setting clock 258000 Hz, block size 512 mci: setting clock 258000 Hz, block size 512 mci: setting clock 258000 Hz, block size 512 mci: setting clock 33024000 Hz, block size 512 reading u-boot.img reading u-boot.img U-Boot 2015.10-rc1-00452-g96a7ed1 (Aug 17 2015 - 10:32:21 +0000) CPU: AT91SAM9G45 Crystal frequency: 12 MHz CPU clock : 400 MHz Master clock : 133.333 MHz Watchdog enabled DRAM: 256 MiB WARNING: Caches not enabled MMC: mci: 0 mci: setting clock 260416 Hz, block size 512 mci: setting clock 260416 Hz, block size 512 mci: setting clock 260416 Hz, block size 512 mci: setting clock 33333333 Hz, block size 512 reading uboot.env In: serial Out: serial Err: serial Net: macb0 Error: macb0 address not set. Hit any key to stop autoboot: 0 U-Boot> Signed-off-by: Erik van Luijk <evanluijk@interact.nl> [add 'picosam9g45_defconfig' to MAINTAINERS] Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
* Merge git://git.denx.de/u-boot-usbTom Rini2015-08-19-0/+2
|\
| * usb: spear: Add support for both SPEAr600 EHCI controllersStefan Roese2015-08-19-0/+2
| | | | | | | | | | | | | | | | | | | | | | USB EHCI on SPEAr600 has not been tested for a while. The base controller addresses are missing. This patch adds the defines to the header. And adds the missing code. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Viresh Kumar <viresh.kumar@linaro.org> Cc: Vipin Kumar <vk.vipin@gmail.com> Cc: Marek Vasut <marex@denx.de>
* | zynqmp: usb: Add usb dwc3 driver support for zynqmpSiva Durga Prasad Paladugu2015-08-19-0/+3
| | | | | | | | | | | | | | | | | | | | Added usb dwc3 driver support for zynqmp this also supports the DFU and LTHOR to download the linux images on to RAM and cen be booted from those linux images. Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* | zynqmp: Enable U-Boot run in EL3Michal Simek2015-08-19-0/+4
|/ | | | | | | Enable Secure IOU setup to enable U-Boot to run in EL3 without setting from ATF. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* lpc32xx: add common USB OHCI defines for all LPC32xx boardsVladimir Zapolskiy2015-08-18-0/+9
| | | | | | | | The change adds a number of macro definitions used by USB OHCI driver, if CONFIG_USB_OHCI_LPC32XX is selected from a board config file. Signed-off-by: Vladimir Zapolskiy <vz@mleia.com> Tested-by: Sylvain Lemieux <slemieux@tycoint.com>
* usb: lpc32xx: add host USB driverSylvain Lemieux2015-08-18-0/+13
| | | | | | | | | | | | | Incorporate USB driver from legacy LPCLinux NXP BSP. The files taken from the legacy patch are: - lpc32xx USB driver - lpc3250 header file USB registers definition. The legacy driver was updated and clean-up as part of the integration with the latest u-boot. Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com> Acked-by: Marek Vasut <marex@denx.de> Tested-by: Vladimir Zapolskiy <vz@mleia.com>
* lpc32xx: move common SLC NAND defines to arch/config.hVladimir Zapolskiy2015-08-18-0/+29
| | | | | | | | | | | | | | | A number of LPC32xx SLC NAND defines is dictated by controller hardware limits and OOB layout is defined by operating system, the definitions are common for all users. Since those macro are used in out of NAND SLC driver code (simple NAND SPL framework), they can not be placed into the driver, therefore move them from board config files to arch/config.h The change also adds OOB layout details specific to small page NAND devices taken from Linux kernel. Signed-off-by: Vladimir Zapolskiy <vz@mleia.com> Tested-by: Sylvain Lemieux <slemieux@tycoint.com>
* dma: lpc32xx: add DMA driverSylvain Lemieux2015-08-18-0/+71
| | | | | | | | | | | | | Incorporate DMA driver from legacy LPCLinux NXP BSP. The files taken from the legacy patch are: - lpc32xx DMA driver - lpc3250 header file DMA registers definition. The legacy driver was updated and clean-up as part of the integration with the latest u-boot. Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com> Acked-by: Marek Vasut <marex@denx.de> Tested-by: Vladimir Zapolskiy <vz@mleia.com>
* Merge branch 'master' of git://git.denx.de/u-boot-spiTom Rini2015-08-18-0/+19
|\
| * ARM: dra7xx_evm: Enable EDMA3 in SPL to support DMA on qspiVignesh R2015-08-17-0/+5
| | | | | | | | | | | | | | | | | | | | | | Enable TI_EDMA3 and SPL_DMA support, so as to reduce boot time. With DMA enabled there is almost 3x improvement in read performance. This helps in reducing boot time in qspiboot mode Also add EDMA3 base address for DRA7XX and AM57XX. Signed-off-by: Vignesh R <vigneshr@ti.com> Reviewed-by: Jagan Teki <jteki@openedev.com>
| * dma: ti-edma3: Add helper function to support edma3 transferVignesh R2015-08-17-0/+2
| | | | | | | | | | Signed-off-by: Vignesh R <vigneshr@ti.com> Reviewed-by: Jagan Teki <jteki@openedev.com>
| * ARM: OMAP5: Add functions to enable and disable EDMA3 clocksVignesh R2015-08-17-0/+7
| | | | | | | | | | | | | | | | | | Adds functions to enable and disable edma3 clocks which can be invoked by drivers using edma3 to control the clocks. Signed-off-by: Vignesh R <vigneshr@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com> Reviewed-by: Jagan Teki <jteki@openedev.com>
| * ARM: OMAP5: Add support for disabling clocks in ubootKishon Vijay Abraham I2015-08-17-0/+4
| | | | | | | | | | | | | | | | | | Add do_disable_clocks() to disable clock domains and module clocks. These clocks are enabled using do_enable_clocks(). Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Vignesh R <vigneshr@ti.com> Reviewed-by: Jagan Teki <jteki@openedev.com>
| * ARM: AM43xx: Add support for disabling clocks in ubootKishon Vijay Abraham I2015-08-17-0/+1
| | | | | | | | | | | | | | | | | | Add do_disable_clocks() to disable clock domains and module clocks. These clocks are enabled using do_enable_clocks(). Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com> Signed-off-by: Vignesh R <vigneshr@ti.com> Reviewed-by: Jagan Teki <jteki@openedev.com>
* | Merge branch 'master' of git://git.denx.de/u-boot-samsungTom Rini2015-08-18-8675/+0
|\ \
| * | ARM: exynos: move SoC sources to mach-exynosThomas Abraham2015-08-17-8675/+0
| |/ | | | | | | | | | | | | | | | | | | | | | | | | | | Move arch/arm/cpu/armv7/exynos/* to arch/arm/mach-exynos/* to allow reuse of existing code for ARMv8 based Exynos platforms. Cc: Minkyu Kang <mk7.kang@samsung.com> Cc: Albert Aribaud <albert.u.boot@aribaud.net> Cc: Masahiro Yamada <yamada.m@jp.panasonic.com> Signed-off-by: Thomas Abraham <thomas.ab@samsung.com> Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com> Tested-by: Przemyslaw Marczak <p.marczak@samsung.com> Acked-by: Przemyslaw Marczak <p.marczak@samsung.com> Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
* | arm: lpc32xx: gpio macro for pin mappingSylvain Lemieux2015-08-17-0/+40
| | | | | | | | | | | | Add LPC32xx GPIO interface macro for pin mapping. Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
* | arm: lpc32xx: mux: add missing registersSylvain Lemieux2015-08-17-1/+18
|/ | | | | | | Add missing registers in struct definition. Update GPIO MUX base register to match GPIO base (refer to "LPC32x0 User manual" Rev. 3 - 22 July 2011). Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
* sun6i: clock: Add support for the mipi pllHans de Goede2015-08-14-0/+15
| | | | | | | | Add support for the mipi pll, this is necessary for getting higher dotclocks with lcd panels. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* sunxi: clock: Add clock_get_pll3() helper functionHans de Goede2015-08-14-0/+8
| | | | | | | Add a helper function to get the pll3 clock rate. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* sunxi: display: Fix composite video out on sun5iHans de Goede2015-08-14-1/+16
| | | | | | | | The tv-encoder on sun5i is slightly different compared to the one on sun4i/sun7i. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* ARM: tegra: Make pinmux.h standalone includibleThierry Reding2015-08-13-0/+2
| | | | | | | | | | | This header file uses type definitions (u8, u32) from linux/types.h but doesn't include it. If includes aren't carefully ordered this can cause build failures. Cc: Tom Warren <twarren@nvidia.com> Signed-off-by: Thierry Reding <treding@nvidia.com> Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
* ARM: tegra: allow reading recovery mode boot typeMarcel Ziswiler2015-08-13-0/+2
| | | | | | | | | | Add defines to allow reading recovery mode (RCM) boot type from the boot information table (BIT) written by the boot ROM (BR) to the IRAM. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Simon Glass <sjg@chromium.org> Acked-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
* gpio: omap: Drop 'method' parameterTom Rini2015-08-12-6/+1
| | | | | | | | | | The "method" parameter was part of the original port of the driver from the kernel. At some point this may have been added to allow for future differentiation (as omap1 and omap2 have different GPIO IP blocks, so this wasn't an unreasonable thing to do). At this point however it's just extra overhead, so drop. Signed-off-by: Tom Rini <trini@konsulko.com>
* gpio: am43xx: expand gpio supportNikita Kiryanov2015-08-12-0/+4
| | | | | | | | | AM43XX SoCs support up to 192 GPIO signals. Make this amount available to the driver. Cc: Albert Aribaud <albert.u.boot@aribaud.net> Cc: Igor Grinberg <grinberg@compulab.co.il> Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
* mmc: hi6220_dw_mmc: Add hi6220 glue code for dw_mmc controller.Peter Griffin2015-08-12-0/+8
| | | | | | | | | This patch adds the glue code for hi6220 SoC which has 2x synopsis dw_mmc controllers. This will be used by the hikey board support in subsequent patches. Signed-off-by: Peter Griffin <peter.griffin@linaro.org> Reviewed-by: Simon Glass <sjg@chromium.org>
* hisilicon: hi6220: Add a hi6220 pinmux driver.Peter Griffin2015-08-12-0/+112
| | | | | | | This patch adds basic pinmux support for the hi6220 SoC, which is found on the hikey board. Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
* ARM: hi6220: Add register and bitfield definition header files.Peter Griffin2015-08-12-0/+807
| | | | | | | This patch adds the header files which will be used in the subsquent board / drivers to enable support for hi6220 hikey board. Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
* dm: gpio: hi6220: Add a hi6220 GPIO driver model driver.Peter Griffin2015-08-12-0/+29
| | | | | | | This patch adds support for the GPIO perif found on hi6220 SoC. Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
* ARM: DRA7/ OMAP5: implement Auxiliary Control Register configurationNishanth Menon2015-08-12-0/+1
| | | | | | | | | | Implement logic for ACR(Auxiliary Control Register) configuration using ROM Code smc service. Suggested-by: Richard Woodruff <r-woodruff2@ti.com> Suggested-by: Brad Griffis <bgriffis@ti.com> Reviewed-by: Brad Griffis <bgriffis@ti.com> Signed-off-by: Nishanth Menon <nm@ti.com>
* Correct License and Copyright information on few filesRuchika Gupta2015-08-12-0/+2
| | | | | | | | | gpio.h - Added missing copyright in few files. rsa-mod-exp.h - Corrected copyright in the file. fsl_sec.h - Added missing license in files drivers/crypto/fsl/Makefile - Removed the incomplete GPLv2 license and replaced it with GPLv2+ license Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
* omap3: Reboot mode supportPaul Kocialkowski2015-08-12-0/+7
| | | | | | | | | | | | | | Reboot mode is written in scratchpad memory before reboot in the form of a single char, that is the first letter of the reboot mode string as passed to the reboot function. This mechanism is supported on OMAP3 both my the upstream kernel and by various TI kernels. It is up to each board to make use of this mechanism or not. Signed-off-by: Paul Kocialkowski <contact@paulk.fr> Reviewed-by: Tom Rini <trini@konsulko.com>
* nand: lpc32xx: add SLC NAND controller supportVladimir Zapolskiy2015-08-12-0/+3
| | | | | | | | | | | | | | | | | | | | | The change adds support of LPC32xx SLC NAND controller. LPC32xx SoC has two different mutually exclusive NAND controllers to communicate with single and multiple layer chips. This simple driver allows to specify NAND chip timings and defines custom read_buf()/write_buf() operations, because access to 8-bit data register must be 32-bit aligned. Support of hardware ECC calculation is not implemented (data correction is always done by software), since it requires a working DMA engine. The driver can be included to an SPL image. Signed-off-by: Vladimir Zapolskiy <vz@mleia.com> Acked-by: Scott Wood <scottwood@freescale.com> Tested-by: Sylvain Lemieux <slemieux@tycoint.com>
* arm: bcmcygnus: Enable Ethernet supportJiandong Zheng2015-08-12-0/+11
| | | | | | | | Enable BCM SF2 ethernet and PHY for BCM Cygnus SoC Signed-off-by: Jiandong Zheng <jdzheng@broadcom.com> Signed-off-by: Steve Rae <srae@broadcom.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
* arm, at91: support for sam9260 based smartweb boardHeiko Schocher2015-08-12-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | add support for the at91sam9260 based board smartweb from siemens. SPL is used without serial support, as this SoC has only 4k sram for running SPL. Here a U-Boot bootlog: RomBOOT > U-Boot 2015.07-rc2-00109-g4ae828c (Jun 15 2015 - 09:31:16 +0200) CPU: AT91SAM9260 Crystal frequency: 18.432 MHz CPU clock : 198.656 MHz Master clock : 99.328 MHz Watchdog enabled DRAM: 64 MiB WARNING: Caches not enabled NAND: 256 MiB In: serial Out: serial Err: serial Net: macb0 Hit any key to stop autoboot: 0 U-Boot> Signed-off-by: Heiko Schocher <hs@denx.de>
* sunxi: display: Add a few extra register and constant definesHans de Goede2015-08-08-6/+42
| | | | | | | | | | | | | Add a few extra sunxi display registers and constant defines. Also rename some existing defines (e.g. dropping _GCTRL) and make some more generic (e.g. dropping the 2x scaling from SUNXI_LCDC_TCON1_TIMING_V_TOTAL). This is a preparation patch for adding composite video out support. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* sunxi: usb-phy: Never power off the usb portsHans de Goede2015-08-08-0/+1
| | | | | | | | | | | | | | | | | | | | | USB devices are not really designed to get the power bounced off and on at them. Esp. USB powered harddisks do not like this. Currently we power off the USB ports both on a "usb reset" and when booting the kernel, causing the usb-power to bounce off and then back on again. This patch removes the powering off calls, fixing the undesirable power bouncing. Note this requires some special handling for the OTG port: 1) We must skip the external vbus check if we've already enabled our own vbus to avoid false positives 2) If on an usb reset we no longer detect that the id-pin is grounded, turn off vbus as that means an external vbus may be present now Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* sunxi: nand: Add pinmux and clock settings for NAND supportKarol Gugala2015-08-08-0/+3
| | | | | | | | | | To enable NAND flash in sunxi SPL, pins 0-6, 8-22 and 24 on port C are configured. Signed-off-by: Karol Gugala <kgugala@antmicro.com> Signed-off-by: Piotr Zierhoffer <pzierhoffer@antmicro.com> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
* Merge git://git.denx.de/u-boot-dmTom Rini2015-08-06-2/+1
|\
| * exynos: video: Remove non-device-tree codeSimon Glass2015-08-05-2/+0
| | | | | | | | | | | | We always use device tree on exynos, so remove the unused code. Signed-off-by: Simon Glass <sjg@chromium.org>
| * exynos: Add support for the DisplayPort hotplug detectSimon Glass2015-08-05-0/+1
| | | | | | | | | | | | Allow this function to be selected using the pinmux API. Signed-off-by: Simon Glass <sjg@chromium.org>
* | ARM: tegra: enable GPU DT node when appropriateAlexandre Courbot2015-08-06-0/+15
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | T124/210 requires some specific configuration (VPR setup) to be performed by the bootloader before the GPU can be used. For this reason, the GPU node in the device tree is disabled by default. This patch enables the node if U-boot has performed VPR configuration. Boards enabled by this patch are T124's Jetson TK1 and Venice2 and T210's P2571. Signed-off-by: Alexandre Courbot <acourbot@nvidia.com> Cc: Stephen Warren <swarren@nvidia.com> Cc: Tom Warren <twarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
* | ARM: tegra: move VPR configuration to a later stageAlexandre Courbot2015-08-06-9/+27
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | U-boot is responsible for enabling the GPU DT node after all necessary configuration (VPR setup for T124) is performed. In order to be able to check whether this configuration has been performed right before booting the kernel, make it happen during board_init(). Also move VPR configuration into the more generic gpu.c file, which will also host other GPU-related functions, and let boards specify individually whether they need VPR setup or not. Signed-off-by: Alexandre Courbot <acourbot@nvidia.com> Cc: Stephen Warren <swarren@nvidia.com> Cc: Tom Warren <twarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
* | Tegra: PLL: use per-SoC pllinfo table instead of PLL_DIVM/N/P, etc.Tom Warren2015-08-05-29/+25
| | | | | | | | | | | | | | | | | | | | | | | | | | Added PLL variables (dividers mask/shift, lock enable/detect, etc.) to new pllinfo struct for each Soc/PLL. PLLA/C/D/E/M/P/U/X. Used pllinfo struct in all clock functions, validated on T210. Should be equivalent to prior code on T124/114/30/20. Thanks to Marcel Ziswiler for corrections to the T20/T30 values. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
* | Tegra: clocks: Add 38.4MHz OSC support for T210 useTom Warren2015-08-05-0/+2
|/ | | | | | | | | | | | | | | Added 38.4MHz/48MHz entries to pll_x_table for CPU PLL. Needs to be measured - should be close to 700MHz (1.4G/2). Note that some freqs aren't in the PLLU table in T210 TRM (13, 26MHz), so I used the 12MHz table entry for them. They shouldn't be selected since they're not viable T210 OSC freqs. Since there are now 2 new OSC defines, all tables (pll_x_table, PLLU) had to increase by two entries, but since 38.4/48MHz are not viable osc freqs on T20/30/114, etc, they're just set to 0. Signed-off-by: Tom Warren <twarren@nvidia.com>
* usb: musb-new: CONFIG_MUSB prefix replacement with CONFIG_USB_MUSBPaul Kocialkowski2015-08-05-1/+1
| | | | | | | | | USB-related options are usually prefixed with CONFIG_USB and platform-specific adaptation for the MUSB controller already have a CONFIG_USB_MUSB prefix, so this switches all MUSB-related options to a CONFIG_USB_MUSB prefix, for consistency. Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
* armv8/lsch3/config: Define USB XHCI controller base address for LS2085ANikhil Badola2015-08-03-0/+3
| | | | | | | | Define base address of both usb xhci controllers in lsch3 config in the format (IMMR + offset) for LS2085A Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* armv8/lsch3/config: Define CONFIG_SYS_CACHELINE_SIZE for LS2085ANikhil Badola2015-08-03-0/+1
| | | | | | | | Define CONFIG_SYS_CACHELINE_SIZE for LS2085A which is required by USB XHCI stack for alignment Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
* Merge branch 'master' of git://www.denx.de/git/u-boot-imxTom Rini2015-08-02-97/+1381
|\
generated by cgit v1.1 at 2024-11-12 01:15:37 +0000