summaryrefslogtreecommitdiff
path: root/arch/arm/cpu
Commit message (Collapse)AuthorAgeLines
...
| * | ARM: fix ifdef in ARMv8 lowlevel_init() againMasahiro Yamada2016-05-23-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | Commit 116611937faa ("ARM: fix ifdefs in ARMv8 lowlevel_init()") accidentally inverted the logic of CONFIG_ARMV8_MULTIENTRY. Fixes: 116611937faa ("ARM: fix ifdefs in ARMv8 lowlevel_init()") Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Reviewed-by: Stephen Warren <swarren@nvidia.com>
* | | imx: correct speed grading info for i.MX6ULPeng Fan2016-05-18-0/+15
|/ / | | | | | | | | | | | | Correct speed grading info for i.MX6UL Signed-off-by: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
* | imx: imx7d: fix ahb clock mux 1Stefan Agner2016-05-17-1/+1
|/ | | | | | | | | | | | | | The clock parent of the AHB root clock when using mux option 1 is the SYS PLL 270MHz clock. This is specified in Table 5-11 Clock Root Table of the i.MX 7Dual Applications Processor Reference Manual. While it could be a documentation error, the 270MHz parent is also mentioned in the boot ROM configuration in Table 6-28: The clock is by default at 135MHz due to a POST_PODF value of 1 (=> divider of 2). Signed-off-by: Stefan Agner <stefan@agner.ch>
* ARM: am33xx: Fix DDR initialization delaysRuss Dill2016-05-06-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | The current delays in the DDR initialization routines for am33xx architectures are sometimes not running long enough leading to DDR init errors. On am437x, this shows up as an L3 NOC error after the kernel boots. This is due to the timer not being initialized properly, but instead still containing the timer init values from the boot ROM which cause timers to expire in 1/4th the time required. timer_init is typically not called until board_init_r, however on am33xx/am43xx udelay is required in sdram_init which is called from board_init_f, so a call to timer_init is required earlier. Note that this issue introduced in v2015.01 by: b352dde "am33xx: Drop timer_init call from s_init". Although this could instead fixed by reverting said commit, it would cause timer_init to be called twice in both SPL and non-SPL cases. This gives a little more fine grained control and also matches what is being done on omap-command and fsl-layerscape. Signed-off-by: Russ Dill <russ.dill@ti.com>
* ARM: fix ifdefs in ARMv8 lowlevel_init()Stephen Warren2016-05-06-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | Commit 724219a65f55 "ARM: always perform per-CPU GIC init" removed some ifdefs to unify the MULTIENTRY-vs-non-MULTIENTRY paths. However, the wrong endif was removed. This patch adds back that missing endif, and adds a new ifdef to match the endif the now-correctly-terminated block used to match against. Use "git show -U25 724219a65f55" to see enough context to make the original issue clear. In practical terms, this makes no difference to runtime behaviour. The code that was incorrectly compiled into the binary when ifndef MULTIENTRY is a no-op for other cases, since branch_if_master evaluates to a hard- coded jump. The only issues were: - A few extra instructions were added to the binary. - The comment on the endif at the very end of the function, indicating which ifdef it matched, were wrong. An alternative might be to simply fix the comment on that trailing ifdef, but that only addresses the second point above, not the first. Fixes: 724219a65f55 ("ARM: always perform per-CPU GIC init") Cc: Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* Fix various typos, scattered over the code.Robert P. J. Day2016-05-05-1/+1
| | | | | | | | | | | | | Spelling corrections for (among other things): * environment * override * variable * ftd (should be "fdt", for flattened device tree) * embedded * FTDI * emulation * controller
* Revert "omap3: Use raw SPL by default for mmc1"Tom Rini2016-05-02-0/+2
| | | | | | | | | | | | | Unfortunately with this change we now are unable to do FS mode boots from MMC1 as with the way the code works today we will always load and assume that the hard-coded raw location contains U-Boot. Further, we cannot fix this by just changing other logic to try FS-then-RAW as it would also make us have to ignore what order the ROM is telling us to try. This reverts commit 22d90d560a2b01c47f180e196e6c6485eb8e65db. Signed-off-by: Tom Rini <trini@konsulko.com>
* ARM: DRA7: Add ABB setup for all domainsNishanth Menon2016-04-25-0/+40
| | | | | | | | | | | | | ABB should be initialized for all required domains voltage domain for DRA7: IVA, GPU, EVE in addition to the existing MPU domain. If we do not do this, kernel configuring just the frequency using the default boot loader configured voltage can fail on many corner lot units and has been hard to debug. This specifically is a concern with DRA7 generation of SoCs since other than VDD_MPU, all other domains are only permitted to setup the voltages to required OPP only at boot. Reported-by: Richard Woodruff <r-woodruff2@ti.com> Signed-off-by: Nishanth Menon <nm@ti.com>
* ARM: OMAP5: Enable ABB configuration for MM voltage domainNishanth Menon2016-04-25-0/+14
| | | | | | | | | | Since we setup the voltage and frequency for the MM domain, we *must* setup the ABB configuration needed for the domain as well. If we do not do this, kernel configuring just the frequency using the default boot loader configured voltage can fail on many corner lot units. Reported-by: Richard Woodruff <r-woodruff2@ti.com> Signed-off-by: Nishanth Menon <nm@ti.com>
* ARM: OMAP5/DRA7: Move ABB TXDONE mask to voltage structureNishanth Menon2016-04-25-2/+5
| | | | | | | | | | | ABB TX_DONE mask will vary depending on ABB module. For example, 3630 never had ABB on IVA domain, while OMAP5 does use ABB on MM domain, DRA7 has it on all domains with the exception of CORE, RTC. Hence, move the txdone mask definition over to structure describing voltage domain. Signed-off-by: Nishanth Menon <nm@ti.com>
* ARM: OMAP5/DRA7: Get rid of control_std_fuse_opp_vdd_mpu_2Nishanth Menon2016-04-25-4/+2
| | | | | | | | | | | | | This information is already available under vcores->volts.efuse.reg. There is no reason for duplicating the information since AVS Class 0 definitions are common for OMAP5 and DRA7 and defined with STD_FUSE_OPP_* macros. This allows a central location of defining the ABB and voltage definitions especially since they are reused. This also makes it simpler to prevent mistakes involved when changing the boot OPP for the device. Signed-off-by: Nishanth Menon <nm@ti.com>
* Merge branch 'master' of git://www.denx.de/git/u-boot-imxTom Rini2016-04-25-0/+156
|\
| * Add initial support for Technexion's PICO-IMX6UL-EMMC boardFabio Estevam2016-04-19-0/+5
| | | | | | | | | | | | | | | | | | | | Add support for Technexion's PICO-IMX6UL-EMMC board. For information about this board, please visit: http://www.technexion.com/products/pico/pico-som/pico-imx6-emmc Signed-off-by: Richard Hu <richard.hu@technexion.com> Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
| * imx: mx6: Fix procedure to switch the parent of LDB_DI_CLKAkshay Bhat2016-04-19-0/+151
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Due to incorrect placement of the clock gate cell in the ldb_di[x]_clk tree, the glitchy parent mux of ldb_di[x]_clk can cause a glitch to enter the ldb_di_ipu_div divider. If the divider gets locked up, no ldb_di[x]_clk is generated, and the LVDS display will hang when the ipu_di_clk is sourced from ldb_di_clk. To fix the problem, both the new and current parent of the ldb_di_clk should be disabled before the switch. This patch ensures that correct steps are followed when ldb_di_clk parent is switched in the beginning of boot. This patch was ported from the 3.10.17 NXP kernel http://git.freescale.com/git/cgit.cgi/imx/linux-2.6-imx.git/commit/?h=imx_3.10.17_1.0.1_ga&id=eecbe9a52587cf9eec30132fb9b8a6761f3a1e6d NXP errata number: ERR009219, EB821 Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <fabio.estevam@nxp.com>
* | ARM: always perform per-CPU GIC initStephen Warren2016-04-18-10/+0
|/ | | | | | | | | | | | | | | | | | The current code in ARMv8's lowlevel_init() skips the per-CPU GIC initialization ifndef CONFIG_ARMV8_MULTIENTRY. However, the per-CPU init should always occur; it's just the one-time init that should only happen on the master. Once this consideration is taken into account, the only difference between the paths when CONFIG_ARMV8_MULTIENTRY is undefined/defined is the use of branch_if_slave. Naively, any unified code would need to invoke this conditionally upon ifdef CONFIG_ARMV8_MULTIENTRY. However, branch_if_slave already checks CONFIG_ARMV8_MULTIENTRY and does nothing if it isn't defined, so we don't even need that ifdef at the call site. Reported-by: Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* Merge branch 'master' of git://www.denx.de/git/u-boot-imxTom Rini2016-04-13-45/+93
|\
| * imx: mx7d: move MX7D to Kconfig entryPeng Fan2016-03-26-0/+1
| | | | | | | | | | | | | | | | | | | | | | If including MX7D in CONFIG_SYS_EXTRA_OPTIONS, CONFIG_ROM_UNIFIED_SECTIONS will not effect.So move MX7D to Kconfig entry from CONFIG_SYS_EXTRA_OPTIONS to "select MX7D" to boards using i.MX7 Dual. Signed-off-by: Peng Fan <van.freenix@gmail.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <fabio.estevam@nxp.com> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
| * imx: mx6sx: move MX6SX to Kconfig entryPeng Fan2016-03-26-0/+2
| | | | | | | | | | | | | | | | | | | | | | If including MX6SX in CONFIG_SYS_EXTRA_OPTIONS, CONFIG_ROM_UNIFIED_SECTIONS will not effect.So move MX6SX to Kconfig entry from CONFIG_SYS_EXTRA_OPTIONS to "select MX6SX" to boards using i.MX6 SoloX. Signed-off-by: Peng Fan <van.freenix@gmail.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <fabio.estevam@nxp.com> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
| * arm: mx6: Add CCV xPress board supportStefan Roese2016-03-26-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch add support for the CCV xPress board which is equipped with the i.MX6UL. And provides the following interfaces: - 128MiB DDR - UART - I2C - eMMC (with booting) - Ethernet - USB This patch adds two build targets. One with and one without SPL. The non-SPL version is used for loading U-Boot via USB (imx_usb_loader). Signed-off-by: Stefan Roese <sr@denx.de> Cc: Fabio Estevam <fabio.estevam@nxp.com> Cc: Stefano Babic <sbabic@denx.de>
| * warp7: Add initial supportFabio Estevam2016-03-26-0/+7
| | | | | | | | | | | | | | | | | | | | | | Add the basic support for Warp7 board. For more information about this reference design, please visit: https://www.element14.com/community/docs/DOC-79058/l/warp-7-the-next-generation-wearable-reference-platform Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> Reviewed-by: Peng Fan <peng.fan@nxp.com>
| * mx27: 16-bit wide watchdog registersLeonid Iziumtsev2016-03-25-4/+4
| | | | | | | | | | | | | | Make the watchdog registers 16-bit wide, as they are according to TRM. Signed-off-by: Leonid Iziumtsev <leonid.iziumtsev@se.atlascopco.com> Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
| * arm: imx6: Switch DDR3 calibration to wait_for_bit()Marek Vasut2016-03-25-32/+12
| | | | | | | | | | | | | | | | | | Switch the DDR3 calibration from ad-hoc implementation of wait_for_bit() to generic implementation of wait_for_bit(). Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de> Reviewed-by: Stefano Babic <sbabic@denx.de>
| * imx: print ARM clock for clocks commandPeng Fan2016-03-25-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Default print ARM clock for clocks command. Test on i.MX6UL 14x14 evk board: " => clocks PLL_SYS 792 MHz PLL_BUS 528 MHz PLL_OTG 480 MHz PLL_NET 50 MHz ARM 396000 kHz " Signed-off-by: Peng Fan <van.freenix@gmail.com> Cc: Stefano Babic <sbabic@denx.de>
| * imx: mx6ul configure the PMIC_STBY_REQ pin as open drainPeng Fan2016-03-25-1/+11
| | | | | | | | | | | | | | | | | | Configure the PMIC_STBY_REQ pin as open drain 100K according to the design team's requirement for the PMIC_STBY_REQ pin for i.MX 6UltraLite TO1.0. Signed-off-by: Peng Fan <van.freenix@gmail.com> Cc: Stefano Babic <sbabic@denx.de>
| * imx: mx6ul: skip setting ahb ratePeng Fan2016-03-25-7/+12
| | | | | | | | | | | | | | | | To i.MX6UL, default ARM rate and AHB rate is 396M and 198M, no need to set them. Signed-off-by: Peng Fan <van.freenix@gmail.com> Cc: Stefano Babic <sbabic@denx.de>
| * imx: mx6: Fix incorrect clear mmdc_ch0 handshake maskYe Li2016-03-25-1/+4
| | | | | | | | | | | | | | | | | | | | | | Since the MX6UL/SL/SX only has one DDR channel, in CCM_CCDR register the bit[17] for mmdc_ch0 is reserved and its proper state should be 1. When clear this bit, the periph_clk_sel cannot be set and that CDHIPR[periph_clk_sel_busy] handshake never clears. Signed-off-by: Ye Li <ye.li@nxp.com> Signed-off-by: Peng Fan <van.freenix@gmail.com> Acked-by: Stefano Babic <sbabic@denx.de>
| * Merge branch 'next'Stefano Babic2016-03-20-0/+31
| |\
| | * mx7: Distinguish between dual and solo versionsFabio Estevam2016-03-09-0/+18
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Read the number of cores in the fuses to distinguish between the dual and solo versions. Tested on a mx7d sabresd and on a mx7solo warp7. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> Reviewed-by: Peng Fan <peng.fan@nxp.com>
| | * arm: imx: Add support for GE Bx50v3 boardsAkshay Bhat2016-03-09-0/+13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add support for GE B450v3, B650v3 and B850v3 boards. The boards are based on Advantech BA16 module which has a i.MX6D processor. The boards support: - FEC Ethernet - USB Ports - SDHC and MMC boot - SPI NOR - LVDS and HDMI display Basic information about the module: - Module manufacturer: Advantech - CPU: Freescale ARM Cortex-A9 i.MX6D - SPECS: Up to 2GB Onboard DDR3 Memory; Up to 16GB Onboard eMMC NAND Flash Supports OpenGL ES 2.0 and OpenVG 1.1 HDMI, 24-bit LVDS 1x UART, 2x I2C, 8x GPIO, 4x Host USB 2.0 port, 1x USB OTG port, 1x micro SD (SDHC),1x SDIO, 1x SATA II, 1x 10/100/1000 Mbps Ethernet, 1x PCIe X1 Gen2 Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com> Reviewed-by: Peng Fan <peng.fan@nxp.com>
* | | arm: Replace v7_maint_dcache_all(ARMV7_DCACHE_INVAL_ALL) with asm codeHans de Goede2016-04-11-96/+74
| | | | | | | | | | | | | | | | | | | | | Lets be consistent and also replace v7_maint_dcache_all() with asm code for the invalidate case. Signed-off-by: Hans de Goede <hdegoede@redhat.com>
* | | arm: Replace v7_maint_dcache_all(ARMV7_DCACHE_CLEAN_INVAL_ALL) with asm codeHans de Goede2016-04-11-36/+91
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | v7_maint_dcache_all() does not work reliable when build with gcc6, see: https://bugzilla.redhat.com/show_bug.cgi?id=1318788 While debugging this I learned that v7_maint_dcache_all() is unreliable when build with gcc5 too when it is marked as noinline. This commit fixes the reliability issues by replacing the C-code with the ready to use asm implementation from the kernel. Given that this code when written as C-code clearly is quite fragile (also see the existing comments about the C-code being the way it is to get optimal assembly) and that we have a proven asm alternative, I believe that this is the best solution. Note that we actually already had a copy of the kernel's v7_flush_dcache_all() before this commit in arch/arm/mach-uniphier/arm32/lowlevel_init.S. This commit moves that code arch/arm/cpu/armv7/cache_v7_asm.S, renames it to __v7_flush_dcache_all(), and adds a v7_flush_dcache_all() wrapper which saves / restores the clobbered registers for use from C-code. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
* | | ARM: allow CONFIG_GICV* not to be definedStephen Warren2016-04-11-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | There are ARM SoCs (such as the BCM2837) do not contain an ARM GIC. Fix the ARMv8 CPU startup code to compile in this case. Signed-off-by: Stephen Warren <swarren@wwwdotorg.org> Reviewed-by: Tom Rini <trini@konsulko.com>
* | | armv8: LS2080A: Consolidate LS2080A and LS2085AYork Sun2016-04-06-12/+39
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | LS2080A is the primary SoC, and LS2085A is a personality with AIOP and DPAA DDR. The RDB and QDS boards support both personality. By detecting the SVR at runtime, a single image per board can support both SoCs. It gives users flexibility to swtich SoC without the need to reprogram the board. Signed-off-by: York Sun <york.sun@nxp.com> CC: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com> Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
* | | ARM64: zynqmp: Select SYS_CONFIG_NAME via KconfigMichal Simek2016-04-04-9/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | This option enable adding new platform suport just by adding defconfig and DTS file which will target generic configuration for SoC. Make no sense to extend Kconfig just create a pointer between DTS and configuration file. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
* | | sniper: Change vendor name from lge to lg, matching devicetree vendor prefixPaul Kocialkowski2016-04-01-1/+1
| | | | | | | | | | | | | | | | | | | | | This moves the sniper board from the lge to lg, in order to match the devicetree vendor prefix already defined in the kernel. Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
* | | sunxi: Move cpu independent code to mach directoryAlexander Graf2016-04-01-4960/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Some of the code in arch/arm/cpu/armv7/sunxi is actually armv7 specific, while most of it is just generic code that could as well be used on an AArch64 SoC. Move all files that are not really tied to armv7 into a new mach-sunxi directory. Signed-off-by: Alexander Graf <agraf@suse.de> Acked-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
* | | sunxi: usb_phy: Add support for A83T USB PHYsChen-Yu Tsai2016-03-31-2/+46
| | | | | | | | | | | | | | | | | | | | | | | | | | | The A83T has 3 USB PHYs: 1 for USB OTG, 1 for standard USB 1.1/2.0 host, 1 for USB HSIC. Signed-off-by: Chen-Yu Tsai <wens@csie.org> Reviewed-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
* | | sunxi: Print soc-id from sram controller for sun8i boardsHans de Goede2016-03-31-5/+19
| | | | | | | | | | | | | | | | | | | | | | | | | | | As the need for various magic sram pokes has shown this maybe useful info to have. e.g. this shows one of my a23 tablets having an id of 1661 rather then the usual 1650 for the a23. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* | | sunxi: Add conditional magic sram poke for A33Hans de Goede2016-03-31-4/+16
| | | | | | | | | | | | | | | | | | | | | | | | | | | I noticed that for certain SoC versions boot0 does a magic poke when build for A33. I'm not aware of this actually being necessary anywhere, but better safe then sorry. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Acked-by: Ian Campbell <ijc@hellion.org.uk>
* | | Merge branch 'master' of git://git.denx.de/u-boot-fsl-qoriqTom Rini2016-03-29-2/+18
|\ \ \
| * | | armv8: fsl-lsch3: Disable SMMU during secure bootSaksham Jain2016-03-29-1/+17
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | During secure boot, SMMU is enabled on POR by SP bootrom. SMMU needs to be put in bypass mode in uboot to enable CAAM transcations to pass through. For non-secure boot, SP BootROM doesn't enable SMMU, which is in bypass mode out of reset. Signed-off-by: Aneesh Bansal <aneesh.bansal@nxp.com> Signed-off-by: Saksham Jain <saksham.jain@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
| * | | armv8: fsl-layerscape: Skip reconfigure QSPI clock when booting from QSPIQianyu Gong2016-03-28-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The qspi_cfg register is set by PBI when booting from QSPI. No need to changing it again. Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
* | | | pxa: add support for D- and I- cachesVasily Khoruzhick2016-03-27-0/+73
| | | | | | | | | | | | | | | | | | | | | | | | Tested with OHCI and pxafb drivers - no issues found Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
* | | | pxa: start.S: enable SRAM clockVasily Khoruzhick2016-03-27-1/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | SRAM is used for early stack, but kernel disables its clock on suspend. Re-enable SRAM clock on startup, otherwise u-boot crashes on resume from suspend. Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
* | | | arm: Add support for HYP mode and LPAE page tablesAlexander Graf2016-03-27-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | We currently always modify the SVC versions of registers and only support the short descriptor PTE format. Some boards however (like the RPi2) run in HYP mode. There, we need to modify the HYP version of system registers and HYP mode only supports the long descriptor PTE format. So this patch introduces support for both long descriptor PTEs and HYP mode registers. Signed-off-by: Alexander Graf <agraf@suse.de>
* | | | ARM: OMAP5/DRA7: Expose do_set_iodelayNishanth Menon2016-03-27-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | do_set_iodelay can now be used from board files based on needs of the platforms variation they have. Signed-off-by: Nishanth Menon <nm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* | | | ARM: OMAP5/DRA7: Split iodelay functionality into sub stepsNishanth Menon2016-03-27-14/+50
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Since many platforms may need different pad configuration required depending on variation of the platform with minor deltas, it is easier to maintain a sub step based approach to allow for pin mux and iodelay configuration which may depend on the platform variations and need to be done in IO isolation. While we retain the older __recalibrate_iodelay function which provides a ready sequencing, __recalibrate_iodelay_start and __recalibrate_iodelay_end may be alternatively used now and the callers will be responsible for the correct sequencing of operations. Signed-off-by: Nishanth Menon <nm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* | | | ARM: DRA72: sdram: Update sdram ext phy configuration for SR2.0Nishanth Menon2016-03-27-1/+43
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Based on data from EMIF configuration tool 1.1.1. Signed-off-by: Nishanth Menon <nm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* | | | ARM: DRA7: hwdata: Update ioreg data for DRA72 SR2.0Nishanth Menon2016-03-27-1/+15
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Based on data from EMIF configuration tool 1.1.1. Expected update for CTRL_WKUP_EMIF1_SDRAM_CONFIG_EXT in the next revision of the tool has been incorporated as well. Signed-off-by: Nishanth Menon <nm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
* | | | ARM: DRA72x: Add support for detection of SR2.0Ravi Babu2016-03-27-0/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add support for detection of SR2.0 version of DRA72x family of processors. Signed-off-by: Ravi Babu <ravibabu@ti.com> Signed-off-by: Nishanth Menon <nm@ti.com> Reviewed-by: Tom Rini <trini@konsulko.com>
generated by cgit v1.1 at 2024-11-08 09:39:17 +0000