summaryrefslogtreecommitdiff
path: root/arch/arm/cpu/arm926ejs/mxs
Commit message (Collapse)AuthorAgeLines
* arm: remove unneeded symbol offsets and _TEXT_BASEAlbert ARIBAUD2014-02-26-27/+0
| | | | | | | | Remove the last uses of symbol offsets in ARM U-Boot. Remove some needless uses of _TEXT_BASE. Remove all _TEXT_BASE definitions. Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
* arm: make _end compiler-generatedAlbert ARIBAUD2014-02-26-2/+7
| | | | | | | | | This prevents references to _end from generating absolute relocation records. This change is binary invariant for ARM targets. Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
* arm: keep all sections in ELF fileAlbert ARIBAUD2013-12-07-7/+9
| | | | | | | | | | Current LDS files /DISCARD/ a lot of sections when linking ELF files, causing diagnostic tools such as readelf or objdump to produce partial output. Keep all section at link stage, filter only at objcopy time so that .bin remains minimal. Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net> Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
* Merge branch 'iu-boot/master' into 'u-boot-arm/master'Albert ARIBAUD2013-11-09-9/+20
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Conflicts: arch/arm/cpu/arm926ejs/mxs/Makefile board/compulab/cm_t35/Makefile board/corscience/tricorder/Makefile board/ppcag/bg0900/Makefile drivers/bootcount/Makefile include/configs/omap4_common.h include/configs/pdnb3.h Makefile conflicts are due to additions/removals of object files on the ARM branch vs KBuild introduction on the main branch. Resolution consists in adjusting the list of object files in the main branch version. This also applies to two files which are not listed as conflicting but had to be modified: board/compulab/common/Makefile board/udoo/Makefile include/configs/omap4_common.h conflicts are due to the OMAP4 conversion to ti_armv7_common.h on the ARM side, and CONFIG_SYS_HZ removal on the main side. Resolution is to convert as this icludes removal of CONFIG_SYS_HZ. include/configs/pdnb3.h is due to a removal on ARM side. Trivial resolution is to remove the file. Note: 'git show' will also list two files just because they are new: include/configs/am335x_igep0033.h include/configs/omap3_igep00x0.h
| * ARM: mxs: Enable DCDC converter for battery bootMarek Vasut2013-10-31-0/+2
| | | | | | | | | | | | | | | | | | | | In case the board detected sufficient voltage for battery boot, make sure the DCDC converter is ON and the board is not running only from linregs, otherwise an instability will be observed. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com>
| * ARM: mxs: Setup stack in JTAG modeMarek Vasut2013-10-17-0/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | In case the MX23/MX28 is switched into JTAG mode via the BootMode select switches, the BootROM bypasses the CPU core registers initialization. This in turn means that the Stack Pointer (SP) register is not set as it is in every other mode of operation, but instead is only zeroed out. To prevent U-Boot SPL from crashing in this obscure JTAG mode, configure the SP to point at the CONFIG_SYS_INIT_SP_ADDR if the SP is zeroed out. Note that in case the SP is already configured, we must preserve that exact SP value and must not modify it. This is important since in every other mode but the JTAG mode, the SPL returns into the BootROM and BootROM in turn loads U-Boot itself. If the SP were to be corrupted, the BootROM won't be able to continue it's operation after returned from SPL and the system would crash. Finally, add the JTAG mode switch identifier, so it's not recognised as Unknown mode. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Stefano Babic <sbabic@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Otavio Salvador <otavio@ossystems.com.br>
| * ARM: mxs: tools: Use mkimage for BootStream generationMarek Vasut2013-10-17-9/+10
| | | | | | | | | | | | | | | | | | | | | | Now that mkimage can generate an BootStream for i.MX23 and i.MX28, use the mkimage as a default tool to generate the BootStreams instead of the elftosb tool. This cuts out another obscure dependency. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Otavio Salvador <otavio@ossystems.com.br> Cc: Stefano Babic <sbabic@denx.de>
* | arm926ejs: convert makefiles to Kbuild styleMasahiro Yamada2013-10-31-23/+3
|/ | | | | | | | | | | | | | | | | Note1: In arch/arm/cpu/arm926ejs/spear/Makefile START := start.o was changed extra-$(CONFIG_SPL_BUILD) := start.o because spear/start.o is only used for SPL. Note2: START := start.o was missing from arch/arm/cpu/arm926ejs/mxs/Makefile. This commit simply adds extra-$(CONFIG_SPL_BUILD) := start.o Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
* Coding Style cleanup: remove trailing white spaceWolfgang Denk2013-10-14-2/+2
| | | | Signed-off-by: Wolfgang Denk <wd@denx.de>
* ARM: mxs: Receive r0 and r1 passed from BootROMMarek Vasut2013-09-10-22/+33
| | | | | | | | | | | | | | | | | Make sure value in register r0 and r1 is preserved and passed to the board_init_ll() and mxs_common_spl_init() where it can be processed further. The value in r0 can be configured during the BootStream generation to arbitary value, r1 contains pointer to return value from CALL'd function. This patch also clears the value in r0 before returning to BootROM to make sure the BootROM is not confused by this value. Finally, this patch cleans up some comments in the start.S file. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Stefano Babic <sbabic@denx.de>
* ARM: mxs: Document the power block initializationMarek Vasut2013-09-10-0/+209
| | | | | | | | | This patch adds documentation for the functions used during the initialization of MXS power block. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Stefano Babic <sbabic@denx.de>
* ARM: mxs: rename function that sets AUTO_RESTART flagHector Palacios2013-08-31-6/+3
| | | | | | | | | | | | | | | | | | The AUTO_RESTART flag of HW_RTC_PERSISTENT0 register will power up the chip automatically 180ms after power down. This bit must be enabled by the boot loader to ensure the target can start upon hardware reset or watchdog reset even when powered from a battery. Currently the function named 'mxs_power_clear_auto_restart()' is setting this flag although the 'clear' in its name suggest the opposite. This patch renames the function to 'mxs_power_set_auto_restart()' and removes the comment about EVK revision A which was confusing because the function indeed was setting the flag. Signed-off-by: Hector Palacios <hector.palacios@digi.com>
* ARM: mxs: tools: Add mkimage support for MXS bootstreamMarek Vasut2013-08-31-0/+14
| | | | | | | | | | | | | | | | | | | | | | | Add mkimage support for generating and verifying MXS bootstream. The implementation here is mostly a glue code between MXSSB v0.4 and mkimage, but the long-term goal is to rectify this and merge MXSSB with mkimage more tightly. Once this code is properly in U-Boot, MXSSB shall be deprecated in favor of mkimage-mxsimage support. Note that the mxsimage generator needs libcrypto from OpenSSL, I therefore enabled the libcrypto/libssl unconditionally. MXSSB: http://git.denx.de/?p=mxssb.git;a=summary The code is based on research presented at: http://www.rockbox.org/wiki/SbFileFormat Signed-off-by: Marek Vasut <marex@denx.de> Cc: Tom Rini <trini@ti.com> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Stefano Babic <sbabic@denx.de> Cc: Otavio Salvador <otavio@ossystems.com.br>
* Add GPL-2.0+ SPDX-License-Identifier to source filesWolfgang Denk2013-07-24-200/+12
| | | | | | Signed-off-by: Wolfgang Denk <wd@denx.de> [trini: Fixup common/cmd_io.c] Signed-off-by: Tom Rini <trini@ti.com>
* remove all references to .dynsymAlbert ARIBAUD2013-06-21-5/+0
| | | | | | | | | | | | | | | | Discard all .dynsym sections from linker scripts Remove all __dynsym_start definitions from linker scripts Remove all __dynsym_start references from the codebase Note: this touches include/asm-generic/sections.h, which is not ARM-specific, but actual uses of __dynsym_start are only in ARM, so this patch can safely go through the ARM repository. Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net> Tested-by: Lubomir Popov <lpopov@mm-sol.com> Tested-by: Jeroen Hofstee <jeroen@myspectrum.nl> Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
* arm: mxs: Fix vectoring table craftingMarek Vasut2013-06-03-3/+22
| | | | | | | | | | | | The vectoring table has to be placed at 0x0, but U-Boot on MX23/MX28 starts from RAM, so the vectoring table at 0x0 is not present. Craft code that will be placed at 0x0 and will redirect interrupt vectoring to proper location of the U-Boot in RAM. Signed-off-by: Marek Vasut <marex@denx.de> CC: Stefano Babic <sbabic@denx.de> CC: Fabio Estevam <fabio.estevam@freescale.com> Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
* Merge branch 'u-boot-imx/master' into 'u-boot-arm/master'Albert ARIBAUD2013-05-11-96/+176
|\ | | | | | | | | | | Conflicts: drivers/mtd/nand/mxc_nand_spl.c include/configs/m28evk.h
| * arm: mxs: Add LCDIF clock configuration functionMarek Vasut2013-05-06-0/+93
| | | | | | | | | | | | | | | | | | | | | | This function turns on the LCDIF clock and configures it's frequency. The dividers settings are calculated within the function and the current implementation should be fast and accurate. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Otavio Salvador <otavio@ossystems.com.br> Cc: Stefano Babic <sbabic@denx.de>
| * arm: mxs: Preprocess u-boot.bd so they contain full pathMarek Vasut2013-05-06-4/+14
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The u-boot-imx23.bd and u-boot-imx28.bd need to be preprocessed, otherwise they have issues with out-of-tree build where elftosb tool couldn't sometimes find the u-boot.bin and spl/u-boot-spl.bin . Preprocess these .bd files with sed and insert full path to u-boot.bin and spl/u-boot-spl.bin to prevent this issue. Moreover, to avoid adding more churn into main Makefile, move all this preprocessing and u-boot.sb generation into CPU directory instead. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Stefano Babic <sbabic@denx.de> Acked-by: Otavio Salvador <otavio@ossystems.com.br>
| * arm: mx23: Fix VDDMEM misconfigurationMarek Vasut2013-05-06-20/+42
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The VDDMEM ramped up in very weird way as it was horribly misconfigured. Instead of setting up VDDMEM in one swipe, let it rise slowly the same way as VDDD and VDDA in spl_power_init.c and then only clear ILIMIT before memory gets inited. This makes sure the VDDMEM rises sanely, not jumps up and down as it did till now. The VDDMEM prior to this change did this: 2V0____ .--------2V5 | `--' 0V____| The VDDMEM now does this: 2V0_____,-----------2V5 / 0V__| Moreover, VDDIO on MX23 uses 25mV steps while MX28 uses 50mV steps, fix this difference too. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Otavio Salvador <otavio@ossystems.com.br> Cc: Stefano Babic <sbabic@denx.de>
| * mxs: Explain why some mx23 DDR registers are not configuredFabio Estevam2013-05-06-0/+9
| | | | | | | | | | | | | | Put an explanation in the source code as to why some DDR registers do not need to be configured. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
| * mx23: Operate DDR voltage supply at 2.5VFabio Estevam2013-05-06-2/+2
| | | | | | | | | | | | | | After the recent fixes in the mx23 DDR setup, it is safe to operate DDR voltage at the recommended 2.5V voltage level again. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
| * mxs: spl_mem_init: Change EMI port priorityFabio Estevam2013-05-05-1/+1
| | | | | | | | | | | | | | | | | | FSL bootlets code set the PORT_PRIORITY_ORDER field of register HW_EMI_CTRL as 0x2, which means: PORT0231 = 0x02 Priority Order: AXI0, AHB2, AHB3, AHB1 Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
| * mxs: spl_mem_init: Skip the initialization of some DRAM_CTL registersFabio Estevam2013-05-05-2/+15
| | | | | | | | | | | | | | | | | | | | | | | | | | HW_DRAM_CTL27, HW_DRAM_CTL28 and HW_DRAM_CTL35 are not initialized as per FSL bootlets code. mx23 Reference Manual mark HW_DRAM_CTL27 and HW_DRAM_CTL28 as "reserved". HW_DRAM_CTL8 is setup as the last element. So skip the initialization of these DRAM_CTL registers. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
| * mxs: spl_mem_init: Remove erroneous DDR settingFabio Estevam2013-05-05-4/+0
| | | | | | | | | | | | | | | | On mx23 there is no 'DRAM init complete' in register HW_DRAM_CTL18. Remove this erroneous setting. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
| * mxs: spl_mem_init: Fix comment about start bitFabio Estevam2013-05-05-1/+1
| | | | | | | | | | | | Start bit is part of HW_DRAM_CTL8 register, so fix the comment. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
| * mx23: Put back RAM voltage level to its original valueFabio Estevam2013-04-28-2/+2
| | | | | | | | | | | | | | | | | | | | commit 5c2f444c9 (mxs: Reset the EMI block on mx23) changed the DDR voltage level, which causes mx23evk to fail to load a kernel. Put back the original values, so that mx23evk can boot a kernel again. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Tested-by: Robert Nelson <robertcnelson@gmail.com>
| * imx: Move some i.MX common functions into the imx-common directoryStefan Roese2013-04-22-63/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch moves the following functions into the imx-common directory: - mxs_wait_mask_set() - mxs_wait_mask_clr() - mxs_reset_block() These are currently used by i.MX28. But the upcoming GPMI NAND port for i.MX6 will also use these functions. So lets move them to a common location to re-use them. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Stefano Babic <sbabic@denx.de> Cc: Marek Vasut <marex@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com>
| * imx: Move some header files from arch-mxs to imx-commonStefan Roese2013-04-22-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The following headers are moved to a i.MX common location: - regs-common.h - regs-apbh.h - regs-bch.h - regs-gpmi.h - dma.h This way this header can be re-used also by other i.MX platforms. For example the i.MX6 which will need it for the upcoming NAND support. Signed-off-by: Stefan Roese <sr@denx.de> Cc: Stefano Babic <sbabic@denx.de> Cc: Marek Vasut <marex@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com>
* | lib: consolidate hang()Andreas Bießmann2013-05-01-7/+0
|/ | | | | | | | | Delete all occurrences of hang() and provide a generic function. Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com> Acked-by: Albert ARIBAUD <albert.u.boot@aribaud.net> [trini: Modify check around puts() in hang.c slightly] Signed-off-by: Tom Rini <trini@ti.com>
* arm: Make all linker scripts compatible with per-symbol sectionsBenoît Thébaudeau2013-04-12-3/+3
| | | | | | | | Let all ARM linker scripts handle properly -ffunction-sections and -fdata-sections. This will be useful for future changes in order to create symbol-specific sections in common .S files. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
* arm: start.S: Fix _TEXT_BASE for SPLBenoît Thébaudeau2013-04-12-0/+4
| | | | | | | | _TEXT_BASE must be set to CONFIG_SPL_TEXT_BASE for generic SPL, and to CONFIG_SYS_TEXT_BASE for non-SPL builds. Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com> Reviewed-by: Tom Rini <trini@ti.com>
* Merge branch 'u-boot-imx/master' into 'u-boot-arm/master'Albert ARIBAUD2013-04-04-9/+9
|\
| * mxs: spl_mem_init: Align DDR2 init with FSL bootlets sourceFabio Estevam2013-03-20-9/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Currently the following kernel hang happens when loading a 2.6.35 kernel from Freeescale on a mx28evk board: RPC: Registered tcp transport module. RPC: Registered tcp NFSv4.1 backchannel transport module. Bus freq driver module loaded IMX usb wakeup probe usb h1 wakeup device is registered mxs_cpu_init: cpufreq init finished ... Loading the same kernel using the bootlets from the imx-bootlets-src-10.12.01 package, the hang does not occur. Comparing the DDR2 initialization from the bootlets code against the U-boot one, we can notice some mismatches, and after applying the same initialization into U-boot the 2.6.35 kernel can boot normally. Also tested with 'mtest' command, which runs succesfully. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Otavio Salvador <otavio@ossystems.com.br> Tested-by: Marek Vasut <marex@denx.de>
* | Merge branch 'master' of git://git.denx.de/u-boot-armTom Rini2013-03-18-21/+47
|\ \ | |/ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Albert's rework of the linker scripts conflicted with Simon's making everyone use __bss_end. We also had a minor conflict over README.scrapyard being added to in mainline and enhanced in u-boot-arm/master with proper formatting. Conflicts: arch/arm/cpu/ixp/u-boot.lds arch/arm/cpu/u-boot.lds arch/arm/lib/Makefile board/actux1/u-boot.lds board/actux2/u-boot.lds board/actux3/u-boot.lds board/dvlhost/u-boot.lds board/freescale/mx31ads/u-boot.lds doc/README.scrapyard include/configs/tegra-common.h Build tested for all of ARM and run-time tested on am335x_evm. Signed-off-by: Tom Rini <trini@ti.com>
| * Merge branch 'u-boot-imx/master' into 'u-boot-arm/master'Albert ARIBAUD2013-03-15-15/+47
| |\
| | * mxs: timrot: Rename local macrosFadil Berisha2013-03-07-8/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Local macros apply to both iMX23 and iMX28. This patch renames local macros with attribute MX28 to MXS. Signed-off-by: Fadil Berisha <f.koliqi@gmail.com> Cc: Marek Vasut <marex@denx.de> Cc: Otavio Salvador <otavio@ossystems.com.br> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Stefano Babic <sbabic@denx.de>
| | * mxs: timrot: Add support to i.MX23Fadil Berisha2013-03-07-2/+21
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch add timer support to i.MX23 and complete bit fields and values on regs-timrot.h. Testet on imx23-olinuxino board. Signed-off-by: Fadil Berisha <f.koliqi@gmail.com> Acked-by: Marek Vasut <marex@denx.de> Cc: Marek Vasut <marex@denx.de> Cc: Otavio Salvador <otavio@ossystems.com.br> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Stefano Babic <sbabic@denx.de> Acked-by: Otavio Salvador <otavio@ossystems.com.br>
| | * mx23: Document the tRAS lockout setting in memory initializationOtavio Salvador2013-03-07-0/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | Add a comment about the tRAS lockout setting of HW_DRAM_CTL08 to enable the 'Fast Auto Pre-Charge' found in the memory chip. The setting is applied after memory initialization and it is worth document it. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
| | * mxs: Rename CONFIG_SPL_MX28_PSWITCH_WAIT to CONFIG_SPL_MXS_PSWITCH_WAITOtavio Salvador2013-03-07-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | The power switch option is compatible with i.MX23 and i.MX28 so the configration option needs to reflect it. We choose 'CONFIG_SPL_MXS_PSWITCH_WAIT' for the option name. Signed-off-by: Otavio Salvador <otavio@ossystems.com.br> Acked-by: Marek Vasut <marex@denx.de>
| | * mxs: mmc: spi: dma: Better wrap the MXS differencesMarek Vasut2013-03-07-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch streamlines the differences between the MX23 and MX28 by implementing a few helper functions to handle different DMA channel mapping, different clock domain for SSP block and fixes a few minor bugs. First of all, the DMA channel mapping is now fixed in dma.h by defining the actual channel map for both MX23 and MX28. Thus, MX23 now does no longer use MX28 channel map which was wrong. Also, there is a fix for MX28 DMA channel map, where the last four channels were incorrect. Next, because correct DMA channel map is in place, the mxs_dma_init_channel() call now bases the channel ID starting from SSP port #0. This removes the need for DMA channel offset being added and cleans up the code. For the same reason, the SSP0 offset can now be used in mxs_dma_desc_append(), thus no need to adjust dma channel number in the driver either. Lastly, the SSP clock ID is now retrieved by calling mxs_ssp_clock_by_bus() which handles the fact that MX23 has shared SSP clock for both ports, while MX28 has per-port SSP clock. Finally, the mxs_ssp_bus_id_valid() pulls out two implementations of the same functionality from MMC and SPI driver into common code. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Otavio Salvador <otavio@ossystems.com.br> Cc: Stefano Babic <sbabic@denx.de>
| | * mxs: Reset the EMI block on mx23Marek Vasut2013-03-07-2/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The real reason for memory instability was the fact that the EMI block was gated and not reset throughout the boards' operation. This patch resets the EMI block properly while also reverts the memory voltage bump. The memory stability issues were caused by the EMI not being reset properly and thus there is no longer need to run the memory at higher voltage than it ought to run at. This partly reverts 8303ed128a55519f19c5f11087032d4bc4e0537a . Signed-off-by: Marek Vasut <marex@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Otavio Salvador <otavio@ossystems.com.br> Cc: Stefano Babic <sbabic@denx.de>
| * | Remove linker lists (LGAs) from SPL linker scriptsAlbert ARIBAUD2013-03-12-6/+0
| |/ | | | | | | | | | | | | | | | | | | | | | | Many SPL linker scripts needlessly include linker lists (aka LGAs). Remove them whenever possible; keep it only in the seven am335x_evm variants (am335x_evm, am335x_evm_uart[1-5], am335x_evm_spiboot), where there is actual content in output section .u_boot_list. This commit keeps all u-boot.bin and u-boot-spl.bin in ARM targets byte-identical. Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
* | Replace __bss_end__ with __bss_endSimon Glass2013-03-15-2/+2
|/ | | | | | | | | | | | | Note this is a tree-wide change affecting multiple architectures. At present we use __bss_start, but mostly __bss_end__. This seems inconsistent and in a number of places __bss_end is used instead. Change to use __bss_end for the BSS end symbol throughout U-Boot. This makes it possible to use the asm-generic/sections.h file on all archs. Signed-off-by: Simon Glass <sjg@chromium.org>
* Merge branch 'master' of git://git.denx.de/u-boot-armTom Rini2013-02-12-56/+225
|\
| * mxs: Use __weak annotation to simplify codeFabio Estevam2013-01-28-7/+4
| | | | | | | | | | | | | | Using the __weak annotation can make the code cleaner. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Acked-by: Marek Vasut <marex@denx.de>
| * mxs: Boost the memory power supplyMarek Vasut2013-01-28-2/+2
| | | | | | | | | | | | | | | | | | | | | | The memory power supply on MX23 didn't pump out enough juice into the DRAM chip, thus caused occasional memory corruption. Fix this. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Otavio Salvador <otavio@ossystems.com.br> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Stefano Babic <sbabic@denx.de> Acked-by: Otavio Salvador <otavio@ossystems.com.br>
| * mxs: Add MX23 quirks into the clock codeOtavio Salvador2013-01-21-9/+26
| | | | | | | | | | | | | | | | | | | | The MX23 has different handling of the SSP clock and GPMI NAND clock sources, add necessary quirks into the clock code to properly handle these. Signed-off-by: Marek Vasut <marex@denx.de> Signed-off-by: Otavio Salvador <otavio@ossystems.com.br> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Stefano Babic <sbabic@denx.de>
| * mxs: Fix the memory init for MX23Otavio Salvador2013-01-21-15/+78
| | | | | | | | | | | | | | | | | | | | The memory init is slightly different on MX23, thus split the memory init for mx23 and mx28 into different functions. Signed-off-by: Marek Vasut <marex@denx.de> Signed-off-by: Otavio Salvador <otavio@ossystems.com.br> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Stefano Babic <sbabic@denx.de>
| * mxs: Add function to ungate the power block on MX23Marek Vasut2013-01-21-0/+12
| | | | | | | | | | | | | | | | | | | | The power block on MX23 must first be ungated before it can be operated. Add function to MXS power init that ungates it. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Fabio Estevam <fabio.estevam@freescale.com> Cc: Otavio Salvador <otavio@ossystems.com.br> Cc: Stefano Babic <sbabic@denx.de>
generated by cgit v1.1 at 2024-12-28 20:41:57 +0000