summaryrefslogtreecommitdiff
Commit message (Collapse)AuthorAgeLines
* vexpress: Check TC2 firmware support before defaulting to nonsec bootingJon Medhurst \(Tixy\)2016-08-15-5/+44
| | | | | | | | | | The firmware on TC2 needs to be configured appropriately before booting in nonsec mode will work as expected, so test for this and fall back to sec mode if required. Signed-off-by: Jon Medhurst <tixy@linaro.org> Reviewed-by: Ryan Harkin <ryan.harkin@linaro.org> Tested-by: Ryan Harkin <ryan.harkin@linaro.org>
* Merge branch 'master' of git://git.denx.de/u-boot-atmelTom Rini2016-08-15-78/+3686
|\
| * mmc: atmel_sdhci: Convert to the driver model supportWenyou Yang2016-08-15-0/+135
| | | | | | | | | | | | | | | | | | | | | | Convert the driver to the driver model while retaining the existing legacy code. This allows the driver to support boards that have converted to driver model as well as those that have not. Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com> Reviewed-by: Heiko Schocher <hs@denx.de>
| * dm: atmel: Add driver model support for the ehci driverWenyou Yang2016-08-15-0/+123
| | | | | | | | | | | | | | | | | | Add driver model support while retaining the existing legacy code. This allows the driver to support boards that have converted to driver model as well as those that have not. Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Acked-by: Simon Glass <sjg@chromium.org>
| * ARM: at91/dt: Add device tree for SAMA5D2 XplainedWenyou Yang2016-08-15-0/+874
| | | | | | | | | | | | Add device tree for SAMA5D2 Xplained board. Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
| * atmel: Bring in at91 pio4 device tree file and bindingsWenyou Yang2016-08-15-0/+946
| | | | | | | | | | | | | | | | Bring in required device tree file and bindings from Linux. Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Reviewed-by: Andreas Bießmann <andreas@biessmann.org> Reviewed-by: Simon Glass <sjg@chromium.org>
| * pinctrl: at91-pio4: Add pinctrl driverWenyou Yang2016-08-15-0/+190
| | | | | | | | | | | | | | | | | | | | | | | | | | | | AT91 PIO4 controller is a combined gpio-controller, pin-mux and pin-config module. The peripheral's pins are assigned through per-pin based muxing logic. The pin configuration is performed on specific registers which are shared along with the gpio controller. So regard the pinctrl device as a child of atmel_pio4 device. Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
| * gpio: atmel_pio4: Rework to support DM & DTWenyou Yang2016-08-15-23/+117
| | | | | | | | | | | | | | | | | | Rework the driver to support driver model and device tree, and support to regard the pio4 pinctrl device as a child of atmel_pio4 device. Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Reviewed-by: Simon Glass <sjg@chromium.org>
| * gpio: atmel_pio4: Move PIO4 definitions to head fileWenyou Yang2016-08-15-53/+53
| | | | | | | | | | | | | | | | | | In order to make these PIO4 definitions shared with AT91 PIO4 pinctrl driver, move them from the existing gpio driver to the head file, and rephrase them. Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Reviewed-by: Simon Glass <sjg@chromium.org>
| * clk.h: inline clk_get_by_name()Andreas Bießmann2016-08-15-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | Fix compile warning for non OF_CONTROL builds: ---8<--- In file included from /Volumes/devel/u-boot/drivers/gpio/atmel_pio4.c:10:0: /Volumes/devel/u-boot/include/clk.h:107:12: warning: 'clk_get_by_name' defined but not used [-Wunused-function] --->8--- Signed-off-by: Andreas Bießmann <andreas@biessmann.org> Acked-by: Stephen Warren <swarren@nvidia.com>
| * clk: at91: Add clock driverWenyou Yang2016-08-15-3/+784
| | | | | | | | | | | | | | | | The patch is referred to at91 clock driver of Linux, to make the clock node descriptions in DT aligned with the Linux's. Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Reviewed-by: Simon Glass <sjg@chromium.org>
| * tpm: atmel_twi: Make compatible with DM I2C bussesmario.six@gdsys.cc2016-08-15-2/+15
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Commit 302c5db ("dm: tpm: Add Driver Model support for tpm_atmel_twi driver") converted the Atmel TWI TPM driver itself to driver model, but kept the legacy-style i2c_write/i2c_read calls. Commit 3e7d940 ("dm: tpm: Every TPM drivers should depends on DM_TPM") then made DM_I2C a dependency of the driver, effectively forcing users to turn on CONFIG_DM_I2C_COMPAT to get it to work. This patch adds the necessary dm_i2c_write/dm_i2c_read calls to make the driver compatible with DM, but also keeps the legacy calls in ifdefs, so that the driver is now compatible with both DM and non-DM setups. Signed-off-by: Mario Six <mario.six@gdsys.cc> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
| * i2c: atmel: DT binding for i2c driverSongjun Wu2016-08-15-0/+26
| | | | | | | | | | | | | | | | DT binding documentation for atmel i2c driver. Signed-off-by: Songjun Wu <songjun.wu@atmel.com> Reviewed-by: Heiko Schocher <hs@denx.de> Acked-by: Heiko Schocher <hs@denx.de>
| * i2c: atmel: add i2c driverSongjun Wu2016-08-15-0/+426
| | | | | | | | | | | | | | | | Add i2c driver. Signed-off-by: Songjun Wu <songjun.wu@atmel.com> Reviewed-by: Heiko Schocher <hs@denx.de> Acked-by: Heiko Schocher <hs@denx.de>
* | Merge branch 'master' of git://git.denx.de/u-boot-netTom Rini2016-08-15-516/+1326
|\ \
| * | net: mii: Clean up legacy glue that is not usedJoe Hershberger2016-08-15-86/+0
| | | | | | | | | | | | | | | | | | | | | | | | The cleanup of the legacy mii registration API that's no longer used now that the drivers have been converted to use the (more) modern API. Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
| * | net: mii: Changes not made by spatchJoe Hershberger2016-08-15-65/+52
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | If the functions passed to the registration function are not in the same C file (extern) then spatch will not handle the dependent changes. Make those changes manually. Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> For the 4xx related files: Acked-by: Stefan Roese <sr@denx.de> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
| * | net: mii: Fix changes made by spatchJoe Hershberger2016-08-15-41/+30
| | | | | | | | | | | | | | | | | | | | | Some of the changes were a bit too complex. Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
| * | net: mii: Use spatch to update miiphy_registerJoe Hershberger2016-08-15-188/+543
| | | | | | | | | | | | | | | | | | | | | Run scripts/coccinelle/net/mdio_register.cocci on the U-Boot code base. Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
| * | scripts: Add a cocci patch for miiphy_registerJoe Hershberger2016-08-15-0/+142
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Many Ethernet drivers still use the legacy miiphy API to register their mdio interface for access to the mdio commands. This semantic patch will convert the drivers from the legacy adapter API to the more modern alloc/register API. Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
| * | net/ethoc: implement MDIO bus and support phylibMax Filippov2016-08-15-6/+150
| | | | | | | | | | | | | | | | | | | | | | | | | | | Implement MDIO bus read/write functions, initialize the bus and scan for the PHY when phylib is enabled. Limit PHY speeds to 10/100 Mbps. Cc: Michal Simek <monstr@monstr.eu> Signed-off-by: Max Filippov <jcmvbkbc@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
| * | net/ethoc: support private memory configurationsMax Filippov2016-08-15-5/+42
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The ethoc device can be configured to have a private memory region instead of having access to the main memory. In that case egress packets must be copied into that memory for transmission and pointers to that memory need to be passed to net_process_received_packet or returned from the recv callback. Signed-off-by: Max Filippov <jcmvbkbc@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
| * | net/ethoc: don't mix virtual and physical addressesMax Filippov2016-08-15-10/+13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Addresses used in buffer descriptors and passed in platform data or device tree are physical. Addresses used by CPU to access packet data and registers are virtual. Don't mix these addresses and use virt_to_phys for translation. Signed-off-by: Max Filippov <jcmvbkbc@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
| * | net/ethoc: support device treeMax Filippov2016-08-15-0/+15
| | | | | | | | | | | | | | | | | | | | | | | | Add .of_match table and .ofdata_to_platdata callback to allow for ethoc device configuration from the device tree. Signed-off-by: Max Filippov <jcmvbkbc@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
| * | net/ethoc: add CONFIG_DM_ETH supportMax Filippov2016-08-15-47/+194
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Extract reusable parts from ethoc_init, ethoc_set_mac_address, ethoc_send and ethoc_receive, move the rest under #ifdef CONFIG_DM_ETH. Add U_BOOT_DRIVER, eth_ops structure and implement required methods. Signed-off-by: Max Filippov <jcmvbkbc@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
| * | net/ethoc: use priv instead of dev internallyMax Filippov2016-08-15-55/+56
| | | | | | | | | | | | | | | | | | | | | | | | | | | Don't use physical base address of registers directly, ioremap it first. Save pointer in private struct ethoc and use that struct in all internal functions. Signed-off-by: Max Filippov <jcmvbkbc@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
| * | net/ethoc: add Kconfig entry for the driverMax Filippov2016-08-15-1/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add Kconfig entry for the driver, remove #define CONFIG_ETHOC from the only board configuration that uses it and put it into that board's defconfig. Cc: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi> Signed-off-by: Max Filippov <jcmvbkbc@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
| * | net: e1000: Fix the build with driver model and SPI EEPROMAlban Bedel2016-08-15-30/+35
| | | | | | | | | | | | | | | | | | | | | | | | | | | When adding support for the driver model the SPI EEPROM feature had been ignored. Fix the build with both CONFIG_DM_ETH and CONFIG_E1000_SPI enabled. Signed-off-by: Alban Bedel <alban.bedel@avionic-design.de> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
| * | net: smsc95xx: Use correct get_unaligned functionsChris Packham2016-08-15-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | The __get_unaligned_le* functions may not be declared on all platforms. Instead, get_unaligned_le* should be used. On many platforms both of these are the same function. Signed-off-by: Chris Packham <judge.packham@gmail.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
| * | net: macb: Fix build error for CONFIG_DM_ETH enabledWenyou Yang2016-08-15-8/+73
| |/ | | | | | | | | | | | | | | Use the right phy_connect() prototype for CONFIGF_DM_ETH. Support to get the phy interface from dt and set GMAC_UR. Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
* | ARM: tegra: set vdd_core for Jetson TK1Bibek Basu2016-08-15-2/+15
| | | | | | | | | | | | | | | | | | | | | | | | Program vdd_core for Jetson TK1 to 1V, which is the max safe voltage for ultra low temperature operations. vdd_cpu and vdd_gpu are already at 1V. Signed-off-by: Bibek Basu <bbasu@nvidia.com> (swarren: fixed comments to better match the code) (swarren: moved board ifdef around data in header, made code generic) (swarren: fixed typos in commit description) Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
* | ARM: tegra: reduce CSITE clock from 204M to 136MBryan Wu2016-08-15-1/+1
| | | | | | | | | | | | | | | | | | | | | | The L4T kernel complains about a CSITE clock rate above 144MHz, presumably because the HW is only characterized for a clock less than that. Adjust the rate to 136MHz to avoid the warning and stay in spec. Signed-off-by: Bryan Wu <pengw@nvidia.com> (swarren, re-wrote commit description) Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
* | ARM: tegra: fix trimslice environment locationStephen Warren2016-08-15-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Trimslice currently stores its environment at 512KiB into the SPI flash chip. The U-Boot binary has grown such that the size of the boot image (which includes the Tegra BCT, padding, and the U-Boot binary) is slightly larger than 512K now. Consequently, writing the boot image to flash corrupts the saved environment, and equally, writing to or erasing the environment will corrupt the bootloader, which in turn will cause the Tegra boot ROM to enter recovery mode during boot, making it look as if the system is non-operational. Note that tegra-uboot-flasher writes to the environment during the flashing process. Solve this by moving the environment as high as possible in flash. This will allow the U-Boot binary to roughly double in size before this problem is hit again, at which point there's nothing we can do anyway since the binary won't fit into flash. 99% of other Tegra boards store the environment in eMMC and use a negative value for CONFIG_ENV_OFFSET, which already automatically places the environment as near the end of boot flash as possible. The 1 remaining board hard-codes CONFIG_ENV_OFFSET to 2MiB, which allows for plenty more bloat. Reported-by: Stephen L Arnold <nerdboy@gentoo.org> Signed-off-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
* | ARM: tegra: move ft_system_setup()Stephen Warren2016-08-15-31/+35
| | | | | | | | | | | | | | | | | | | | | | Currently, ft_system_setup() is implemented by board*.c, which are a bit of a dumping ground for a bunch of unrelated functionality, and separate versions exist for pre-Tegra186 and Tegra186. Move the implementation into a separate file to separate functionality, and allow sharing. Signed-off-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
* | ARM: tegra: enable PCIe controller on p2771-0000Stephen Warren2016-08-15-0/+75
| | | | | | | | | | | | | | | | | | | | | | p2771-0000 has a couple of PCIe ports; one physically x4 desktop PCI connector (which may run at x2 electrically, depending on the board version and configuration) and a x1 connection to the M.2 slot (which may not be active, depending on the board version and configuration). This change enables those. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
* | ARM: tegra: enable SD card on p2771-0000Stephen Warren2016-08-15-0/+52
| | | | | | | | | | | | | | | | | | | | Now that clock and reset drivers exist for Tegra186, we can enable the SD card controller. Now that a BPMP I2C driver exists for Tegra186, we can communicate with the PMIC to enable power to the SD card. Hook up the DT content and board code required to make the SD card work. Signed-off-by: Stephen Warren <swarren@nvidia.com> Signed-off-by: Tom Warren <twarren@nvidia.com>
* | ARM: tegra: enable I2C buses for P2771-0000Bryan Wu2016-08-15-0/+38
| | | | | | | | | | | | | | | | | | | | Enable I2C devices in DT and enable building tegra_i2c.c driver. Signed-off-by: Bryan Wu <pengw@nvidia.com> (swarren, commit msg rework, fixed DT node sort order) Signed-off-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
* | i2c: tegra: add standardized clk/reset API supportBryan Wu2016-08-15-4/+85
| | | | | | | | | | | | | | | | | | | | | | | | | | clk/reset API was tested on T186 platform and previous chip like T210/T124 will still use the old APIs. Signed-off-by: Bryan Wu <pengw@nvidia.com> (swarren, simplified some ifdefs, removed indent level inside an ifdef) (swarren, added comment about the ifdefs) Signed-off-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Heiko Schocher <hs@denx.de> Signed-off-by: Tom Warren <twarren@nvidia.com>
* | pci: tegra: port to standard clock/reset/pwr domain APIsStephen Warren2016-08-15-5/+159
| | | | | | | | | | | | | | | | | | | | | | | | | | Tegra186 supports the new standard clock, reset, and power domain APIs. Older Tegra SoCs still use custom APIs. Enhance the Tegra PCIe driver so that it can operate with either set of APIs. On Tegra186, the BPMP handles all aspects of PCIe PHY (UPHY) programming. Consequently, this logic is disabled too. Signed-off-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
* | mmc: tegra: port to standard clock/reset APIsStephen Warren2016-08-15-10/+62
| | | | | | | | | | | | | | | | | | | | Tegra186 supports the new standard clock and reset APIs. Older Tegra SoCs still use custom APIs. Enhance the Tegra MMC driver so that it can operate with either set of APIs. Signed-off-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
* | i2c: add Tegra186 BPMP driverStephen Warren2016-08-15-0/+140
| | | | | | | | | | | | | | | | | | | | | | On Tegra186, some I2C controllers are directly controlled by the main CPU, whereas others are controlled by the BPMP, and can only be accessed by the main CPU via IPC requests to the BPMP. This driver covers the latter case. Signed-off-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Simon Glass <sjg@chromium.org> Reviewed-by: Heiko Schocher <hs@denx.de> Signed-off-by: Tom Warren <twarren@nvidia.com>
* | power domain: add Tegra186 driverStephen Warren2016-08-15-0/+100
| | | | | | | | | | | | | | | | | | | | In Tegra186, SoC power domains are manipulated using IPC requests to the BPMP (Boot and Power Management Processor). This change implements a driver that does that. Signed-off-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
* | reset: add Tegra186 reset driverStephen Warren2016-08-15-0/+91
| | | | | | | | | | | | | | | | | | | | | | In Tegra186, on-SoC reset signals are manipulated using IPC requests to the BPMP (Boot and Power Management Processor). This change implements a driver that does that. It is unconditionally selected by CONFIG_TEGRA186 since virtually any Tegra186 build of U-Boot will need the feature. Signed-off-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
* | clock: add Tegra186 clock driverStephen Warren2016-08-15-0/+120
| | | | | | | | | | | | | | | | | | | | | | | | In Tegra186, on-SoC clocks are manipulated using IPC requests to the BPMP (Boot and Power Management Processor). This change implements a driver that does that. A tegra/ sub-directory is created to follow the existing pattern. It is unconditionally selected by CONFIG_TEGRA186 since virtually any Tegra186 build of U-Boot will need the feature. Signed-off-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
* | misc: add Tegra BPMP driverStephen Warren2016-08-15-0/+1863
|/ | | | | | | | | | | | | | | The Tegra BPMP (Boot and Power Management Processor) is a separate auxiliary CPU embedded into Tegra to perform power management work, and controls related features such as clocks, resets, power domains, PMIC I2C bus, etc. This driver provides the core low-level communication path by which feature-specific drivers (such as clock) can make requests to the BPMP. This driver is similar to an MFD driver in the Linux kernel. It is unconditionally selected by CONFIG_TEGRA186 since virtually any Tegra186 build of U-Boot will need the feature. Signed-off-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Warren <twarren@nvidia.com>
* Merge git://git.denx.de/u-boot-dmTom Rini2016-08-12-33/+100
|\
| * misc: add "call" uclass opStephen Warren2016-08-12-0/+46
| | | | | | | | | | | | | | | | | | | | The call op requests that the callee pass a message to the underlying HW or device, wait for a response, and then pass back the response error code and message to the callee. It is useful for drivers that represent some kind of messaging or IPC channel to a remote device. Signed-off-by: Stephen Warren <swarren@nvidia.com> Acked-by: Simon Glass <sjg@chromium.org>
| * power: pmic: act8846: add missing newline to debug statementsJohn Keeping2016-08-12-2/+2
| | | | | | | | | | Signed-off-by: John Keeping <john@metanate.com> Acked-by: Simon Glass <sjg@chromium.org>
| * power: regulator: act8846: fix reading valuesJohn Keeping2016-08-12-2/+2
| | | | | | | | | | | | | | | | | | The voltage and control registers need to be looked up from the value in driver_data. Adjust the get_value and get_enable functions to match the corresponding set_* functions. Signed-off-by: John Keeping <john@metanate.com> Acked-by: Simon Glass <sjg@chromium.org>
| * fdt: allow fdtdec_get_addr_size_*() to translate addressesStephen Warren2016-08-12-17/+36
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Some code may want to read reg values from DT, but from nodes that aren't associated with DM devices, so using dev_get_addr_index() isn't appropriate. In this case, fdtdec_get_addr_size_*() are the functions to use. However, "translation" (via the chain of ranges properties in parent nodes) may still be desirable. Add a function parameter to request that, and implement it. Update all call sites to default to the original behaviour. Signed-off-by: Stephen Warren <swarren@nvidia.com> Reviewed-by: Simon Glass <sjg@chromium.org> Squashed in build fix from Stephen: Signed-off-by: Simon Glass <sjg@chromium.org>
generated by cgit v1.1 at 2024-11-08 08:18:46 +0000