summaryrefslogtreecommitdiff
Commit message (Collapse)AuthorAgeLines
* tsec: fix link detection for the RTL8211B PHYAnton Vorontsov2008-03-25-2/+3
| | | | | | | | | | | RTL8211B sets link state register after autonegotiation complete, so with bootdelay=0 RTL8211B will report lack of the link. To fix this, we should wait for aneg to complete, even if the link is currently down. Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* mpc83xx: add "fsl,soc" and "fsl,immr" compatible fixupsAnton Vorontsov2008-03-25-0/+8
| | | | | | | | | | device_type = "soc" is being deprecated, newer device trees will use "fsl,soc" and/or "fsl,immr" for the soc nodes. This patch also adds clock-frequency property for soc nodes (the same value as bus-frequency). Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
* Modified the DDR SDRAM clock control register to delay MCK/MCK_B 3/4 clockJoe D'Abbraccio2008-03-25-1/+1
| | | | | | | | | With the original value of 1/2 clock cycle delay, the system ran relatively stable except when we run benchmarks that are intensive users of memory. When I run samba connected disk with a HDBENCH test, the system locks-up or reboots sporadically. Signed-off by: Joe D'Abbraccio <Joe.D'abbraccio@freescale.com>
* mpc83xx: Set PCI I/O bus-address base to zero.Scott Wood2008-03-25-5/+5
| | | | | | | | | | The device trees for these boards describe PCI I/O as starting from address zero from the device's perspective. Placing I/O elsewhere may cause problems with certain PCI boards, and may cause problems with Linux. Signed-off-by: Scott Wood <scottwood@freescale.com>
* mpc83xx: MPC8360E-RDK: use 33.3(3)MHz CLKIN/SYS_CLKAnton Vorontsov2008-03-25-2/+2
| | | | | | | At least on the "33MHz Pilot" board crystal is actually 33.3MHz. This patch fixes "system time drifting" problem. Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
* mpc83xx: MPC8360E-RDK: define CONFIG_OF_STDOUT_VIA_ALIASAnton Vorontsov2008-03-25-0/+1
| | | | | | This is needed to update /choosen/linux,stdout-path properly. Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
* mpc83xx: MPC8360E-RDK: add dhcp commandAnton Vorontsov2008-03-25-4/+3
| | | | | | | Plus modify environment to use it and remove bootfile env variable, it is internal and CONFIG_BOOTFILE is used for these purposes. Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
* mpc83xx: MPC8360E-RDK: rework ddr setup, enable eccAnton Vorontsov2008-03-25-13/+38
| | | | | | | | Current DDR setup easily causes memory corruption, this patch fixes it. Also fix TIMING_CFG0_MRS_CYC definition. Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
* mpc83xx: MPC8360E-RDK: configure pario pins for AD7843 and FHCIAnton Vorontsov2008-03-25-0/+17
| | | | | | | This patch adds qe pario pins configuration for AD7843 ADC/Touchscreen controller and FHCI (QE USB). Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
* mpc83xx: MPC8360E-RDK: add support for NANDAnton Vorontsov2008-03-25-1/+99
| | | | Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
* mpc83xx: MPC8360E-RDK: use RGMII_RXID interface modeAnton Vorontsov2008-03-25-2/+2
| | | | | | This is needed for BCM PHYs to work on this board. Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
* uec: add support for Broadcom BCM5481 Gigabit PHYAnton Vorontsov2008-03-25-0/+41
| | | | | | | | | This patch adds basic support for Broadcom BCM5481 PHY. RXD-RXC delay quirk comes from MPC8360E-RDK BSP source, author is Peter Barada <peterb@logicpd.com>. Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
* uec: add support for RGMII_RXID interface modeAnton Vorontsov2008-03-25-0/+2
| | | | | | | PHY drivers will use it to setup software delay between RXD and RXC signals. Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
* uec: add support for gbit mii status readingsAnton Vorontsov2008-03-25-9/+24
| | | | Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
* 83xx: define CONFIG_OF_STDOUT_VIA_ALIAS for the MPC837XERDB boardsAnton Vorontsov2008-03-25-0/+1
| | | | | | This is primarily for the early console support. Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
* 83xx: initialize serdes for MPC837XRDB boardsAnton Vorontsov2008-03-25-0/+43
| | | | | | | | On the MPC8377ERDB: 2 SATA and 2 PCI-E. On the MPC8378ERDB: 2 PCI-E On the MPC8379ERDB: 4 SATA Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
* 83xx: serdes setup routinesAnton Vorontsov2008-03-25-0/+167
| | | | | | This patch adds few routines to configure serdes on 837x targets. Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
* 83xx: split COBJS onto separate linesAnton Vorontsov2008-03-25-11/+12
| | | | | | ..plus get rid of some #ifdefs in the .c files. Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
* 83xx: nand support for MPC837XRDB boardsAnton Vorontsov2008-03-25-0/+19
| | | | Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
* Enable CONFIG_FLASH_SHOW_PROGRESS on the MPC8360EMDS.Jerry Van Baren2008-03-25-0/+1
| | | | | Signed-off-by: Gerald Van Baren <vanbaren@cideas.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* mpc8323erdb: remove RTC and add EEPROMMichael Barkowski2008-03-25-3/+4
| | | | | | | There's no on-board RTC on the MPC8323ERDB, but there is an EEPROM. Signed-off-by: Michael Barkowski <michael.barkowski@freescale.com> Acked-by: Kim Phillips <kim.phillips@freescale.com>
* mpc8323erdb: Improve the system performanceMichael Barkowski2008-03-25-14/+28
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The following changes are based on kernel UCC ethernet performance: 1. Make the CSB bus pipeline depth as 4, and enable the repeat mode 2. Optimize transactions between QE and CSB. Added CFG_SPCR_OPT switch to enable this setting. The following changes are based on the App Note AN3369 and verified to improve memory latency using LMbench: 3. CS0_CONFIG[AP_n_EN] is changed from 1 to 0 4. CS0_CONFIG[ODT_WR_CONFIG] set to 1. Was a reserved setting previously. 5. TIMING_CFG_1[WRREC] is changed from 3clks to 2clks (based on Twr=15ns, and this was already the setting in DDR_MODE) 6. TIMING_CFG_1[PRETOACT] is changed from 3clks to 2clks. (based on Trp=15ns) 7. TIMING_CFG_1[ACTTOPRE] is changed from 9clks to 6clks. (based on Tras=40ns) 8. TIMING_CFG_1[ACTTORW] is changed from 3clks to 2clks. (based on Trcd=15ns) 9. TIMING_CFG_1[REFREC] changed from 21 clks to 11clks. (based on Trfc=75ns) 10. TIMING_CFG_2[FOUR_ACT] is changed from 10 clks to 7clks. (based on Tfaw=50ns) 11. TIMING_CFG_2[ADD_LAT] and DDR_MODE[AL] changed from 0 to 1 (based on CL=3 and WL=2). Signed-off-by: Michael Barkowski <michael.barkowski@freescale.com> Acked-by: Kim Phillips <kim.phillips@freescale.com>
* mpc8323erdb: use readable DDR config macrosMichael Barkowski2008-03-25-8/+42
| | | | | | | Use available shift/mask macros to define DDR configuration. Signed-off-by: Michael Barkowski <michael.barkowski@freescale.com> Acked-by: Kim Phillips <kim.phillips@freescale.com>
* 83xx: Add Vitesse VSC7385 firmware uploadingTimur Tabi2008-03-25-71/+196
| | | | | | | | | | Update the MPC8349E-mITX, MPC8313E-RDB, and MPC837XE-RDB board files to upload the Vitesse VSC7385 firmware. Changed CONFIG_VSC7385 to CONFIG_VSC7385_ENET. Cleaned up the board header files to make selecting the VSC7385 easier to control. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* NET: Add Vitesse VSC7385 firmware uploadingTimur Tabi2008-03-25-0/+115
| | | | | | | | | | | | | | | The Vitesse VSC7385 is a 5-port switch found on the Freescale MPC8349E-mITX and other boards. A small firwmare must be uploaded to its on-board memory before it can be enabled. This patch adds the code which uploads firmware (but not the firmware itself). Previously, this feature was provided by a U-Boot application that was made available only on Freescale BSPs. The VSC7385 firmware must still be obtained separately, but at least there is no longer a need for a separate application. Signed-off-by: Timur Tabi <timur@freescale.com> Acked-by: Ben Warren <biggerbadderben@gmail.com>
* Coding Style cleanyp; update CHANGELOGWolfgang Denk2008-03-26-56/+832
| | | | Signed-off-by: Wolfgang Denk <wd@denx.de>
* Merge branch 'master' of git://www.denx.de/git/u-boot-mipsWolfgang Denk2008-03-26-455/+1058
|\
| * [MIPS] Move gth2_config from ARM section to MIPSShinya Kuribayashi2008-03-25-5/+5
| | | | | | | | Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
| * [MIPS] Extend MIPS_MAX_CACHE_SIZE upto 64kBShinya Kuribayashi2008-03-25-5/+9
| | | | | | | | Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
| * [MIPS] Fix dcache_status()Shinya Kuribayashi2008-03-25-3/+7
| | | | | | | | | | | | You can't judge UNCACHED by Config.K0 LSB. Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
| * [MIPS] Introduce _machine_restartShinya Kuribayashi2008-03-25-8/+42
| | | | | | | | | | | | Handles machine specific functions by using weak functions. Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
| * [MIPS] Cleanup CP0 Status initializationShinya Kuribayashi2008-03-25-9/+25
| | | | | | | | | | | | | | | | Add setup_c0_status from Linux. For the moment we disable interrupts, set CU0, mark the kernel mode, and clear ERL and EXL. This is good enough for reset-time configuration and will work well across most processors. Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
| * [MIPS] Initialize CP0 Cause before setting up CP0 Status registerShinya Kuribayashi2008-03-25-3/+3
| | | | | | | | | | | | | | Without this change, we'll be suffering from deffered WATCH exception once Status.EXL is cleared. Make sure Cause.WP is cleared. Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
| * [MIPS] INCA-IP: Move watchdog init code from start.S to lowlevel_init()Shinya Kuribayashi2008-03-25-8/+6
| | | | | | | | | | | | Move things to appropriate place. Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
| * [MIPS] Implement flush_cache()Shinya Kuribayashi2008-03-25-0/+22
| | | | | | | | | | | | | | | | | | We do Hit_Writeback_Inv_D and Hit_Invalidate_I. You might think that you don't need to do Hit_Invalidate_I, but flush_cache() needs it since this function is used not only in U-Boot specfic programs but also at loading target binaries. Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
| * [MIPS] Fix I-/D-cache initialization loopsShinya Kuribayashi2008-03-25-39/+76
| | | | | | | | | | | | | | | | | | | | | | | | | | Currently we do 1) Index_Store_Tag_I, 2) Fill and 3) Index_Store_Tag_I again per a loop for I-cache initialization. But according to 'See MIPS Run', we're encouraged to use three separate loops rather than combining them *for both I- and D-cache*. This patch tries to fix this. In accordance with fixing above, mips_init_[id]cache are separated from mips_cache_reset(), and rewrite cache loops are completely rewritten with useful macros. Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
| * [MIPS] Replace memory clearance code with f_fill64Shinya Kuribayashi2008-03-25-15/+28
| | | | | | | | | | | | This routine fills memory with zero by 64 bytes, and is 64-bit capable. Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
| * [MIPS] cpu/mips/cache.S: Introduce NESTED/LEAF/END macrosShinya Kuribayashi2008-03-25-18/+416
| | | | | | | | | | | | | | | | | | | | This patch replaces the current function definitions with NESTED, LEAF and END macro. They specify some more additional information about the function; an alignment of symbol, type of symbol, stack frame usage, etc. These information explicitly tells the assembler and the debugger about the types of code we want to generate. Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
| * [MIPS] asm headers' updatesShinya Kuribayashi2008-03-25-343/+416
| | | | | | | | | | | | Make some asm headers adjusted to the latest Linux kernel. Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
| * [MIPS] Request for the 'mips_cache_lock()' removalShinya Kuribayashi2008-03-25-0/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The initial intension of having mips_cache_lock() was to use the cache as memory for temporary stack use so that a C environment can be set up as early as possible. But now mips_cache_lock() follow lowlevel_init(). We've already have the real memory initilaized at this point, therefore we could/should use it. No reason to lock at all. Other problems: Cache locking is not consistent across MIPS implementaions. Some imple- mentations don't support locking at all. The style of locking varies - some support per line locking, others per way, etc. Some parts use bits in status registers instead of cache ops. Current mips_cache_lock() is not necessarily general-purpose. And this is worthy of special mention; once U-Boot/MIPS locks the lines, they are never get unlocked, so the code relies on whatever gets loaded after U-Boot to re-initialize the cache and clear the locks. We're sup- posed to have CFG_INIT_RAM_LOCK and unlock_ram_in_cache() implemented, but leave the situation as it is for a long time. For these reasons, I proposed the removal of mips_cache_lock() from the global start-up code. This patch adds CFG_INIT_RAM_LOCK_MIPS to make existing users aware that *things have changed*. If he wants the same behavior as before, he needs to have CFG_INIT_RAM_LOCK_MIPS in his config file. If we don't have any regression report through several releases, then we'll remove codes entirely. Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp> Acked-by: Andrew Dyer <amdyer@gmail.com>
* | Merge branch 'master' of git://www.denx.de/git/u-boot-mpc86xxWolfgang Denk2008-03-26-0/+0
|\ \
| * | FSL: Move board/mpc7448hpc2 under board/freescaleJon Loeliger2008-03-25-1/+1
| | | | | | | | | | | | Signed-off-by: Jon Loeliger <jdl@freescale.com>
| * | FSL: Move board/mpc8266ads under board/freescaleJon Loeliger2008-03-25-1/+1
| | | | | | | | | | | | Signed-off-by: Jon Loeliger <jdl@freescale.com>
| * | FSL: Move board/mpc8260ads under board/freescaleJon Loeliger2008-03-25-3/+3
| |/ | | | | | | Signed-off-by: Jon Loeliger <jdl@freescale.com>
* | Remove deprecated CONFIG_OF_HAS_UBOOT_ENV and CONFIG_OF_HAS_BD_TJerry Van Baren2008-03-26-234/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | These defines embedded the u-boot env variables and/or the bd_t structure in the fdt blob. The conclusion of discussion on the u-boot email list was that embedding these in the fdt blob is not useful: there are better ways of passing the data (in fact, the fdt blob itself replaces the bd_t struct). The only board that enables these is the stxxtc and they don't appear to be used by linux. Signed-off-by: Gerald Van Baren <vanbaren@cideas.com> Acked-by: Kim Phillips <kim.phillips@freescale.com>
* | rtc: Remove 2nd reference to max6900.o in drivers/rtc/MakefileStefan Roese2008-03-26-1/+0
| | | | | | | | Signed-off-by: Stefan Roese <sr@denx.de>
* | Add Flex-OneNAND booting supportKyungmin Park2008-03-26-17/+36
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Flex-OneNAND is a monolithic integrated circuit with a NAND Flash array using a NOR Flash interface. This on-chip integration enables system designers to reduce external system logic and use high-density NAND Flash in applications that would otherwise have to use more NOR components. Flex-OneNAND enables users to configure to partition it into SLC and MLC areas in more flexible way. While MLC area of Flex-OneNAND can be used to store data that require low reliability and high density, SLC area of Flex-OneNAND to store data that need high reliability and high performance. Flex-OneNAND can let users take advantage of storing these two different types of data into one chip, which is making Flex-OneNAND more cost- and space-effective. Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
* | MPC5200: support setup without FECAndré Schwarz2008-03-25-0/+4
| | | | | | | | | | | | | | | | Include FEC specific nodes in ft_cpu_setup only if CONFIG_MPC5xxx_FEC is defined. Systems without FEC, i.e. no FEC node in DTB, should be possible. Signed-off-by: Andre Schwarz <andre.schwarz@matrix-vision.de> Acked-by: Grant Likely <grant.likely@secretlab.ca>
* | FSL: Move board/mpc8266ads under board/freescaleJon Loeliger2008-03-25-1/+1
| | | | | | | | Signed-off-by: Jon Loeliger <jdl@freescale.com>
* | FSL: Move board/mpc7448hpc2 under board/freescaleJon Loeliger2008-03-25-1/+1
| | | | | | | | Signed-off-by: Jon Loeliger <jdl@freescale.com>
generated by cgit v1.1 at 2024-12-25 20:00:26 +0000