summaryrefslogtreecommitdiff
Commit message (Collapse)AuthorAgeLines
...
* ENGR00315894-19 iMX6 Disable the L2 before chaning the PL310 latencyYe.Li2014-06-17-0/+3
| | | | | | | | | | | The Latency parameters of PL310 Tag RAM latency control register and Data RAM Latency control register are set in L2 cache enable. Setting these registers must have PL310 not enabled. But when using Plugin mode boot, the PL310 is enabled by bootrom. Thus, disable the PL310 before this setting. Signed-off-by: Ye.Li <B37916@freescale.com>
* ENGR00315894-18 i.mx6: increase the console I/O buffer to 1KYe.Li2014-06-17-4/+4
| | | | | | | | Current console buffer is 256 bytes long, it is too small. increase it to 1K. Signed-off-by: Huang Shijie <b32955@freescale.com> Signed-off-by: Ye.Li <B37916@freescale.com>
* ENGR00315894-17 imx6q:sabresd/sabreauto: add SATA supportYe.Li2014-06-17-12/+231
| | | | | | | | This patch adds the SATA support for i.mx6qsabresd and i.mx6qsabreauto board Signed-off-by: Jason Liu <r64343@freescale.com> Signed-off-by: Ye.Li <B37916@freescale.com>
* ENGR00315894-16 env_mmc: add the dynamtic mmc dev supportYe.Li2014-06-17-9/+23
| | | | | | | | This patch add the support to load/save env to the slot which was used as the boot media by dynamic detection. Signed-off-by: Jason Liu <r64343@freescale.com> Signed-off-by: Ye.Li <B37916@freescale.com>
* ENGR00315894-15 i.mx6:sabreauto: Remove duplicated I2C settingsYe.Li2014-06-17-8/+3
| | | | | | | | 1. The i2c2 bus is setup twice, remove the duplication. 2. The i2c settings are duplicated in mx6qsabreauto.h and mx6sabre_common.h, remove it from mx6qsabreauto.h Signed-off-by: Ye.Li <B37916@freescale.com>
* ENGR00315894-14 i.mx6:sabreauto/sabresd/slevk Remove unused CONFIG_SYS_I2C_SLAVEYe.Li2014-06-17-6/+3
| | | | | | | The CONFIG_SYS_I2C is enabled on i.mx6 boards. So the CONFIG_SYS_I2C_SLAVE becomes to unused. Remove this setting. Signed-off-by: Ye.Li <B37916@freescale.com>
* ENGR00315894-13 i.mx6q:sabresd: update the DDR scriptYe.Li2014-06-17-123/+95
| | | | | | | | | This patch update the DDR script to the ddr-scripts-rel.git based on the top of the following commit: 7cd1c3b Removed the duplicate script files Signed-off-by: Jason Liu <r64343@freescale.com> Signed-off-by: Ye.Li <B37916@freescale.com>
* ENGR00315894-12 i.mx6:sabreauto/sabresd: Change the MMC settingsYe.Li2014-06-17-8/+7
| | | | | | | | | | | | | | | | | | | | | | | 1. Change CONFIG_MMCROOT to mmcblk0p2. Kernel always sets the first availiable MMC/SD device to mmcblk0 2. Make the MMC ENV DEV/PART independent of ENV_IS_IN_MMC 3. Add the CONFIG_SYS_MMC_ENV_PART to 0 (user area) for u-boot env saving. CONFIG_SYS_MMC_ENV_PART: was used to tell the u-boot which emmc (boot)partition to be used for the env_mmc.Usually, the emmc card will have 2 boot partitions, boot1 and boot2. 0: means user area 1: means boot partition 1 2: means boot partition 2 If user want to use the boot partition to store the u-boot env, please change the CONFIG_SYS_MMC_ENV_PART to which boot partition you want. 4. Add the CONFIG_SYS_MMC_IMG_LOAD_PART for the partition number where the kernel and DTB will load from. At default, it is the first partition in VFAT format. Signed-off-by: Ye.Li <B37916@freescale.com>
* ENGR00315894-11 i.mx6:shutdown vddpu and pcie phy to save powerYe.Li2014-06-17-0/+31
| | | | | | | | shutdown vddpu and pcie phy to save power Signed-off-by: Anson Huang <b20788@freescale.com> Signed-off-by: Jason Liu <r64343@freescale.com> Signed-off-by: Ye.Li <B37916@freescale.com>
* ENGR00315894-10 i.mx6:sabreauto: Add the GPMI nand supportYe.Li2014-06-17-3/+122
| | | | | | | | | | | Add the GPMI nand support to the iMX6 sabreauto: --Enable the GPMI NAND at default. --Enable the clocks --Set the default environment for nand boot Signed-off-by: Huang Shijie <b32955@freescale.com> Signed-off-by: Jason Liu <r64343@freescale.com> Signed-off-by: Ye.Li <B37916@freescale.com>
* ENGR00315894-9 i.mx6q/dl/solo:sabreauto: Add the WEIM-NOR supportYe.Li2014-06-17-9/+143
| | | | | | | Add the WEIM-NOR support Signed-off-by: Jason Liu <r64343@freescale.com> Signed-off-by: Ye.Li <B37916@freescale.com>
* ENGR00315894-8 imximage: Fix imximage bug for EIM-NOR bootYe.Li2014-06-17-0/+7
| | | | | | | | | | | The load region size of EIM-NOR are defined to 0. For this case, the parameter "imximage_init_loadsize" must be calculated. The imximage tool implements the calculation in the "imximage_generate" function, but the following function "imximage_set_header" resets the value and not calculate. This bug cause some fields of IVT head are not correct, for example the boot_data and DCD overlay the application area. Signed-off-by: Ye.Li <B37916@freescale.com>
* ENGR00315894-7 i.mx6q/dl/solo: sabresd/sabreauto: Add the SPI-NOR supportYe.Li2014-06-17-35/+97
| | | | | | | | | | This patch adds the SPI-NOR support for the i.mx6q/dl/solo:sabresd/auto board: - Support the SPI-NOR function with sf command, - Support the enviroment from SPI-NOR when CONFIG_SYS_BOOT_SPINOR Signed-off-by: Jason Liu <r64343@freescale.com> Signed-off-by: Ye.Li <B37916@freescale.com>
* ENGR00315894-6 i.mx6:sabreauto: Add the i.MX6solo sabreauto supportYe.Li2014-06-17-0/+123
| | | | | | | | | | | | | This patch is to add the i.MX6solo sabreauto support, The i.MX6solo sabreauto board configuration has the following difference with i.MX6dl sabreauto: - DDR bus width: 32bit - DDR capacity: 1024M Signed-off-by: Jason Liu <r64343@freescale.com> Signed-off-by: Ye.Li <B37916@freescale.com>
* ENGR00315894-5 i.mx6:sabreauto: Add the i.MX6DL sabreauto board supportYe.Li2014-06-17-1/+148
| | | | | | | | | | | | | This patch is to add the i.MX6DL sabreauto board support. i.MX6DL sabreauto board share the same design with i.MX6Q sabreauto board except the SOC difference. The DDR script has been updated to the v0.2 version from ddr-scripts-rel.git, the commit based on is: bfd157a Updated MX6DL and MX6DQ ARD and SabreSD scripts Signed-off-by: Jason Liu <r64343@freescale.com> Signed-off-by: Ye.Li <B37916@freescale.com>
* ENGR00315894-4 iMX6Q:SABREAUTO: Disable the DTB for MX6QSABREAUTO boardYe.Li2014-06-17-3/+0
| | | | | | | The DTB for mx6qsabreauto is empty. To support more iMX6 sabreauto boards, remove this DTB in building. Signed-off-by: Ye.Li <B37916@freescale.com>
* ENGR00315894-3 iMX6q:SABREAUTO: Rename the imximage.cfg to mx6q.cfgYe.Li2014-06-17-2/+2
| | | | | | | Rename the imximage.cfg to mx6q.cfg. No function change at all. Signed-off-by: Ye.Li <B37916@freescale.com>
* ENGR00315894-2 iMX6:SABRESD: Add the i.MX6solo SABRESD board supportYe.Li2014-06-17-0/+131
| | | | | | | | | | The i.MX6solo sabre-sd board configuration has the following difference with i.MX6dl sabre-sd: - DDR bus width: 32bit - DDR capacity: 512M Signed-off-by: Ye.Li <B37916@freescale.com>
* ENGR00315894-1 iMX6q/dl:SABREAUTO/SABRESD: Refactor configurations for more ↵Ye.Li2014-06-17-15/+161
| | | | | | | | | | | | | iMX6 boards 1. Make the DDR size configurable based on the boards.cfg 2. Make the FDT file configurable based on the boards.cfg 3. Add DDR and boot configuration script for iMX6dl. Change default boot from SD card. The DDR script has been updated to the v1.5 version from ddr-scripts-rel commit: bfd157a Updated MX6DL and MX6DQ ARD and SabreSD scripts. Signed-off-by: Ye.Li <B37916@freescale.com>
* image: add support for Android's boot image formatSebastian Siewior2014-06-13-6/+204
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the Android boot-image format. The header file is from the Android project and got slightly alterted so the struct + its defines are not generic but have something like a namespace. The header file is from bootloader/legacy/include/boot/bootimg.h. The header parsing has been written from scratch and I looked at bootloader/legacy/usbloader/usbloader.c for some details. The image contains the physical address (load address) of the kernel and ramdisk. This address is considered only for the kernel image. The "second image" defined in the image header is currently not supported. I haven't found anything that is creating this. v3 (Rob Herring): This is based on http://patchwork.ozlabs.org/patch/126797/ with the following changes: - Rebased to current mainline - Moved android image handling to separate functions in common/image-android.c - s/u8/char/ in header to fix string function warnings - Use SPDX identifiers for licenses - Cleaned-up file source information: android_image.h is from file include/boot/bootimg.h in repository: https://android.googlesource.com/platform/bootable/bootloader/legacy The git commit hash is 4205b865141ff2e255fe1d3bd16de18e217ef06a usbloader.c would be from the same commit, but it does not appear to have been used for any actual code. v4: - s/andriod/android/ - Use a separate flag ep_found to track if the entry point has been set rather than using a magic value. Cc: Wolfgang Denk <wd@denx.de> Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Rob Herring <robh@kernel.org> Reviewed-by: Tom Rini <trini@ti.com> Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
* ENGR00315499-22 video: ipu: wait for DP SF end irq when disabling sync BG flowLiu Ying2014-06-13-22/+22
| | | | | | | | | | | Instead of waiting for DC triple buffer to be cleared, this patch changes to wait for a relevant DP sync flow end irq when disabling sync BG flows. In this way, we align the implement to the FSL internal IPUv3 driver. After applying this patch, the uboot hang up issue at the arch_preboot_os stage on the MX6DL platforms is not observed any more. Signed-off-by: Liu Ying <Ying.Liu@freescale.com> Signed-off-by: Nitin Garg <nitin.garg@freescale.com>
* ENGR00315499-21 HDMI: splash screen function enhancementNitin Garg2014-06-13-31/+72
| | | | | | | | | | | | -Change HDMI video mode to VGA. -Add pixel clock fraction part setting in IPU driver, fix video mode timing issue. -Add overflow state clear workaround, fix kernel hang in HDMI driver issue. -Correct IPU clock to 264MHz. Signed-off-by: Sandor Yu <R01008@freescale.com> Signed-off-by: Nitin Garg <nitin.garg@freescale.com>
* ENGR00315499-20 ARM:imx6 Fix USDHC driver bug in PIO modeYe.Li2014-06-13-15/+10
| | | | | | | | | | | | | | | | | When configure the USDHC driver to PIO mode by defining "CONFIG_SYS_FSL_ESDHC_USE_PIO", the SD/MMC read and write will fail. Two bugs in the driver to cause the issue: 1. The read buffer was invalidated after reading from DATAPORT register, which should be only applied to DMA mode. The valid data in cache was overwritten by physical memory. 2. The watermarks are not set in PIO mode, will cause according state not be set. Signed-off-by: Ye.Li <B37916@freescale.com> (cherry picked from commit e2ced39867a3001390bd23069e56b513ed268bb0) Signed-off-by: Nitin Garg <nitin.garg@freescale.com>
* ENGR00315499-19 Fix eMMC fast boot hang issueYe.Li2014-06-13-9/+37
| | | | | | | | | | | | | When booting in eMMC fast boot, the uboot v2013.04 always hangs. The root cause is that MMC host does not exit from boot mode after bootrom loading image. So the first command 'CMD0' sent in uboot will pull down the CMD line to low and cause errors. This patch cleans the MMC boot register in "mmc_init" to put the MMC host back to normal mode. Signed-off-by: Ye Li <b37916@freescale.com> Signed-off-by: Nitin Garg <nitin.garg@freescale.com>
* ENGR00315499-18 driver:MAX7310: Add GPIO expander driver for MAX7310Ye.Li2014-06-13-1/+242
| | | | | | | | | | | | Implement simple functionalities for MAX7310 GPIO input and output. Because MAX7310 is a off-chip device and need to co-exist with on-chip GPIO, new APIs are added specifically for expander device. CONFIG_MAX7310_IOEXP is used to enable the MAX7310 driver. The I2C related configurations also need to set together. Signed-off-by: Ye.Li <B37916@freescale.com> Signed-off-by: Nitin Garg <nitin.garg@freescale.com>
* ENGR00315499-17 ARM:imx6sl:evk Add SPI NOR flash boot and access supportNitin Garg2014-06-13-3/+63
| | | | | | | | | | | Add BSP codes to support SPI NOR flash read, write and erase by using "sf" command. In addition, add a new configuration "mx6slevk_spinor" for building the uboot that can be booted from SPI NOR flash and stored the environments variables in it. Signed-off-by: Ye.Li <B37916@freescale.com> Signed-off-by: Nitin Garg <nitin.garg@freescale.com>
* ENGR00315499-16 I2C: add I2C support on Sabre- boardNitin Garg2014-06-13-1/+206
| | | | | | | | - add I2C support on Sabresd ,Sabreauto board. - add pfuze init code based on I2C transfer in Sabre* board file. Signed-off-by: Robin Gong <b38343@freescale.com> Signed-off-by: Nitin Garg <nitin.garg@freescale.com>
* ENGR00315499-15 ARM:imx6sl:evk Add USB HOST supportNitin Garg2014-06-13-1/+45
| | | | | | | | Enable the USB EHCI for the imx6slevk board. Add VBUS control pin settings and related BSP codes. Signed-off-by: Ye.Li <B37916@freescale.com> Signed-off-by: Nitin Garg <nitin.garg@freescale.com>
* ENGR00315499-14 ARM:imx6:sabresd/arm2 Add USB HOST BSP supportNitin Garg2014-06-13-2/+99
| | | | | | | | | Enable the USB EHCI on sabresd and arm2 boards to support USB mass storage device. Pins are configured in board_ehci_hcd_init for VBUS control. Signed-off-by: Ye.Li <B37916@freescale.com> Signed-off-by: Nitin Garg <nitin.garg@freescale.com>
* ENGR00315499-13 ARM:imx6:EHCI Update OTG support for imx6slNitin Garg2014-06-13-5/+11
| | | | | | | | | Set Power polarity in CTRL register to active-high to control the off-chip power switch. Update USB base address to support imx6sl. Signed-off-by: Nitin Garg <nitin.garg@freescale.com>
* ENGR00315499-12: ARM: MSL: add i2c0 support for imx6sl evkNitin Garg2014-06-13-0/+106
| | | | | | | | - Add i2c0 support for imx6sl evk platform. - Read pmic device ID and revsion ID. Signed-off-by: Fugang Duan <B38611@freescale.com> Signed-off-by: Nitin Garg <nitin.garg@freescale.com>
* ENGR00315499-11 ARM:imx6 Change static environment SD/MMC storage to dynamicNitin Garg2014-06-13-16/+411
| | | | | | | | | | | | | | | | | | | imx6 boards (sabresd, sabreauto, arm2 and slevk) have multiple SD/MMC ports to boot. But current uboot hard code the SD/MMC port for environment variables storage. So if customer changes a port without modifying the configuration "CONFIG_SYS_MMC_ENV_DEV", error will issue at saving and loading environment. Implement a mechanism to detect SD/MMC port from SRC SMBR register, and override the default "mmc_get_env_devno". The "board_late_mmc_env_init" is used to set "mmcdev" when booting from SD/MMC port. Finally after booting from SD/MMC, the environment storage device and "mmcdev" are both set to current SD/MMC port. Customers don't need to re-build the image if booting from different SD/MMC port. This patch also adds SD1 and SD3 support to imx6slevk BSP, and adds support for sabreauto SD1 slot on base board. Signed-off-by: Ye.Li <B37916@freescale.com> Signed-off-by: Nitin Garg <nitin.garg@freescale.com>
* ENGR00315499-10 ARM:imx6:sabresd/sabreauto Add android fastboot supportingNitin Garg2014-06-13-0/+3872
| | | | | | | | | | | | | | | | | | Support android features: fastboot, booti command and recovery for sabresd SD, sabresd eMMC, sabreauto SD, sabreauto NAND. For all booting media (SD, eMMC, NAND), inherits the partitions layout from v2009.08. Fastboot will detect the booting media to replace hardcoding fastboot device. SATA is not supported. FDT is supported to use the "unused" fields in bootimg header which requires the FDT to be combined into the boot.img. For non-FDT boot.img, the "unused" fields should left to NULL and is compatible to boot. Signed-off-by: Ye.Li <B37916@freescale.com> Signed-off-by: Nitin Garg <nitin.garg@freescale.com>
* ENGR00315499-9: ARM:iMX6SL EVK: Add keyboard supportNitin Garg2014-05-27-0/+867
| | | | | | | i.MX6sl evk has keyboards on the board, so add mxc_keyb driver to support key press checking. Signed-off-by: Nitin Garg <nitin.garg@freescale.com>
* ENGR00315499-8 Auto check if boot from usbNitin Garg2014-05-27-0/+47
| | | | | | | | If boot from usb, reset environment to default value. Auto apply mfgtools setting and boot mfgtools kernel. Signed-off-by: Frank Li <Frank.li@freescale.com> Signed-off-by: Nitin Garg <nitin.garg@freescale.com>
* ENGR00315499-7 Add EPDC splash screen for MX 6DL SabreSD and 6SL EVKNitin Garg2014-05-27-0/+1712
| | | | | | | | | | | | | | | | | Add EPDC splash screen feature for MX6SL EVK, and MX6DL SABRESD board. - Currently, splash screen consists of a simple black border around a white screen. Done this way to save in memory footprint. - EPDC splash screen is disabled by default in the config file for MX6DL_SABRESD and MX6SL_EVK. If left enabled, the U-Boot image will not boot correctly (hang), since some additional content on the boot device (waveform file) is required for EPDC splash to work correctly. Please refer to Linux Reference Manual for how to flash WAVEFORM file. Signed-off-by: Robby Cai <R63905@freescale.com> Signed-off-by: Nitin Garg <nitin.garg@freescale.com>
* ENGR00315499-6 ARM:imx6: Add USB gadget driver imx_udc to support Android ↵Nitin Garg2014-05-27-0/+2365
| | | | | | | | | | | | | | fastboot Android fastboot leans on the USB gadget driver to communicate with host. Porting the imx_udc driver from v2009.08 with two changes: adding resource/memory release APIs and replacing the uncached memory with cache flush&invalidate operations. Pins and Clocks initialization are added to support boards: mx6qdlsabresd, mx6qdlsabreauto, mx6slevk Signed-off-by: Ye.Li <B37916@freescale.com> Signed-off-by: Nitin Garg <nitin.garg@freescale.com>
* ENGR00315499-5: Support i.MX6 1.2GHz via LDO bypassNitin Garg2014-05-27-7/+257
| | | | | | | | Add check for 1.2GHz core speed. If Speed grading fuse is for 1.2GHz, enable LDO bypass and setup PMIC voltages. LDO bypass is dependent on the flatten device tree file. Signed-off-by: Nitin Garg <nitin.garg@freescale.com>
* ENGR00315499-4: Add support for i.MX6 Plugin imagesNitin Garg2014-05-27-52/+853
| | | | | | | Support generating plugin images. Make sure not to effect the size of DCD images. Signed-off-by: Nitin Garg <nitin.garg@freescale.com>
* ENGR00315499-3: Support i.MX6 HAB authentication of kernel imageNitin Garg2014-05-27-13/+319
| | | | | | | Support HAB authentication of kernel or secondary images via bootm or hab_auth_img u-boot command. Signed-off-by: Nitin Garg <nitin.garg@freescale.com>
* ENGR00315499-2: Enabled CONFIG_SYS_GENERIC_BOARD for i.MX6 sabresdNitin Garg2014-05-27-0/+1
| | | | | | Enabled CONFIG_SYS_GENERIC_BOARD for i.MX6 sabresd boards. Signed-off-by: Nitin Garg <nitin.garg@freescale.com>
* ENGR00315499-1: Add i.MX6 CPU temperature sensor supportNitin Garg2014-05-27-4/+693
| | | | | | Support CPU temperature sensors on i.MX6 SoC. Signed-off-by: Nitin Garg <nitin.garg@freescale.com>
* Prepare v2014.04Tom Rini2014-04-14-1/+1
| | | | Signed-off-by: Tom Rini <trini@ti.com>
* arm: kzm9g: Add CONFIG_SYS_GENERIC_BOARDTetsuyuki Kobayashi2014-04-14-0/+1
| | | | | | | | Add CONFIG_SYS_GENERIC_BOARD to use common/board_[fr].c for kzm9g. Signed-off-by: Tetsuyuki Kobayashi <koba@kmckk.co.jp> Acked-by: Heiko Schocher <hs@denx.de> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
* i2c: sh_i2c: bugfix: i2c probe command does not workTetsuyuki Kobayashi2014-04-14-1/+3
| | | | | | | | | | | | | | | | | | | | This is regression of commit 2035d77d i2c: sh_i2c: Update to new CONFIG_SYS_I2C framework Before commit 2035d77d, i2c probe command works properly on kzm9g board. KZM-A9-GT# i2c probe Valid chip addresses: 0C 12 1D 32 39 3D 40 60 After commit 2035d77d, i2c probe command does not work. KZM-A9-GT# i2c probe Valid chip addresses: 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F 20 21 22 23 24 25 26 27 28 29 2A 2B 2C 2D 2E 2F 30 31 32 33 34 35 36 37 38 39 3A 3B 3C 3D 3E 3F 40 41 42 43 44 45 46 47 48 49 4A 4B 4C 4D 4E 4F 50 51 52 53 54 55 56 57 58 59 5A 5B 5C 5D 5E 5F 60 61 62 63 64 65 66 67 68 69 6A 6B 6C 6D 6E 6F 70 71 72 73 74 75 76 77 78 79 7A 7B 7C 7D 7E 7F sh_i2c_probe() calls sh_i2c_read(), but read length is 0. So acutally it does not read device at all. This patch prepares dummy buffer and read data into it. Signed-off-by: Tetsuyuki Kobayashi <koba@kmckk.co.jp> Acked-by: Heiko Schocher <hs@denx.de> Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
* board:tricorder: fixup SPL OOB layoutAndreas Bießmann2014-04-11-5/+6
| | | | | | | | | | | Commit d016dc42cedbf6102e100fa9ecb58462edfb14f8 changed the layout of BCH8 SW on omap3 boards. We need to adopt the ecc layout for the nand_spl_simle driver to avoid wrong ecc errors. Signed-off-by: Andreas Bießmann <andreas.biessmann@corscience.de> Cc: Thomas Weber <thomas.weber@corscience.de> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
* board:tricorder: enable omap_gpio clocksAndreas Bießmann2014-04-11-0/+3
| | | | | | Signed-off-by: Andreas Bießmann <andreas.biessmann@corscience.de> Cc: Thomas Weber <thomas.weber@corscience.de> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
* board:tricorder: always work with valid eeprom dataAndreas Bießmann2014-04-11-0/+2
| | | | | | | | | | | | | Commit 890880583d84607e36b52a785a96b167728bbf73 introduced EEPROM parsing and board detection but faild to return a valid tricorder_eeprom struct for backup case. When pressing S200 while reading EEPROM we ignore the value. We returned falsely a tricorder_eeprom struct with uninitialized data which is just garbage. Initialize it by zeroing the whole structure. Signed-off-by: Andreas Bießmann <andreas.biessmann@corscience.de> Cc: Thomas Weber <thomas.weber@corscience.de> Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
* arm:board:trats2:FIX: Clear INFORM4 and INFORM5 registers at correct bootŁukasz Majewski2014-04-11-0/+13
| | | | | | | | | | | | | | During switch to device tree, commit 1ecab0f has removed this code. INFORM4 and INFORM5 registers are used by TRATS2 first stage bootloader for providing recovery. For normal operation, those two must be cleared out. This error emerges when one force reset from u-boot's command line for three times. Signed-off-by: Lukasz Majewski <l.majewski@samsung.com> Cc: Minkyu Kang <mk7.kang@samsung.com> Acked-by: Minkyu Kang <mk7.kang@samsung.com>
* kbuild: fix a bug in regeneration of linker scriptsMasahiro Yamada2014-04-11-6/+6
| | | | | | | | | | | | | | | | | | | | | In some use cases, SPL linker script was not updated even when it should be. For instance, $ make tricoder_config all [ build complete ] ... modify include/configs/tricoder.h $ make spl/u-boot-spl.lds should be updated in this case, but it wasn't. To fix this problem, linker scripts generation should be handled by $(call if_changed_dep,...) rather than by $(call if_changed,...). Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com> Reported-by: Andreas Bießmann <andreas.devel@googlemail.com> Tested-by: Andreas Bießmann <andreas.devel@googlemail.com>
generated by cgit v1.1 at 2024-11-06 05:25:17 +0000