diff options
Diffstat (limited to 'include')
| -rw-r--r-- | include/configs/omap1510.h | 756 | ||||
| -rw-r--r-- | include/configs/omap5912osk.h | 174 |
2 files changed, 0 insertions, 930 deletions
diff --git a/include/configs/omap1510.h b/include/configs/omap1510.h deleted file mode 100644 index 5482722..0000000 --- a/include/configs/omap1510.h +++ /dev/null @@ -1,756 +0,0 @@ -/* - * - * BRIEF MODULE DESCRIPTION - * OMAP hardware map - * - * Copyright (C) 2001 RidgeRun, Inc. (http://www.ridgerun.com) - * Author: RidgeRun, Inc. - * Greg Lonnon (glonnon@ridgerun.com) or info@ridgerun.com - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include <linux/sizes.h> - -/* - There are 2 sets of general I/O --> - 1. GPIO (shared between ARM & DSP, configured by ARM) - 2. MPUIO which can be used only by the ARM. - - Base address FFFB:5000 is where the ARM accesses the MPUIO control registers - (see 7.2.2 of the TRM for MPUIO reg definitions). - - Base address E101:5000 is reserved for ARM access of the same MPUIO control - regs, but via the DSP I/O map. This address is unavailable on 1510. - - Base address FFFC:E000 is where the ARM accesses the GPIO config registers - directly via its own peripheral bus. - - Base address E101:E000 is where the ARM can access the same GPIO config - registers, but the access takes place through the ARM port interface (called - API or MPUI) via the DSP's peripheral bus (DSP I/O space). - - Therefore, the ARM should setup the GPIO regs thru the FFFC:E000 addresses - instead of the E101:E000 addresses. The DSP has only read access of the pin - control register, so this may explain the inability to write to E101:E018. - Try accessing pin control reg at FFFC:E018. - */ -#define OMAP1510_GPIO_BASE 0xfffce000 -#define OMAP1510_GPIO_START OMAP1510_GPIO_BASE -#define OMAP1510_GPIO_SIZE SZ_4K - -#define OMAP1510_MCBSP1_BASE 0xE1011000 -#define OMAP1510_MCBSP1_SIZE SZ_4K -#define OMAP1510_MCBSP1_START 0xE1011000 - -#define OMAP1510_MCBSP2_BASE 0xFFFB1000 - -#define OMAP1510_MCBSP3_BASE 0xE1017000 -#define OMAP1510_MCBSP3_SIZE SZ_4K -#define OMAP1510_MCBSP3_START 0xE1017000 - -/* - * Where's the flush address (for flushing D and I cache?) - */ -#define FLUSH_BASE 0xdf000000 -#define FLUSH_BASE_PHYS 0x00000000 - -#ifndef __ASSEMBLER__ - -#define PCIO_BASE 0 - -/* - * RAM definitions - */ -#define MAPTOPHYS(a) ((unsigned long)(a) - PAGE_OFFSET) -#define KERNTOPHYS(a) ((unsigned long)(&a)) -#define KERNEL_BASE (0x10008000) -#endif - -/* macro to get at IO space when running virtually */ -#define IO_ADDRESS(x) ((x)) - -/* ---------------------------------------------------------------------------- - * OMAP1510 system registers - * ---------------------------------------------------------------------------- - */ - -#define OMAP1510_UART1_BASE 0xfffb0000 /* "BLUETOOTH-UART" */ -#define OMAP1510_UART2_BASE 0xfffb0800 /* "MODEM-UART" */ -#define OMAP1510_RTC_BASE 0xfffb4800 /* RTC */ -#define OMAP1510_UART3_BASE 0xfffb9800 /* Shared MPU/DSP UART */ -#define OMAP1510_COM_MCBSP2_BASE 0xffff1000 /* Com McBSP2 */ -#define OMAP1510_AUDIO_MCBSP_BASE 0xffff1800 /* Audio McBSP2 */ -#define OMAP1510_ARMIO_BASE 0xfffb5000 /* keyboard/gpio */ - -/* - * OMAP1510 UART3 Registers - */ - -#define OMAP_MPU_UART3_BASE 0xFFFB9800 /* UART3 through MPU bus */ - -/* UART3 Registers Maping through MPU bus */ - -#define UART3_RHR (OMAP_MPU_UART3_BASE + 0) -#define UART3_THR (OMAP_MPU_UART3_BASE + 0) -#define UART3_DLL (OMAP_MPU_UART3_BASE + 0) -#define UART3_IER (OMAP_MPU_UART3_BASE + 4) -#define UART3_DLH (OMAP_MPU_UART3_BASE + 4) -#define UART3_IIR (OMAP_MPU_UART3_BASE + 8) -#define UART3_FCR (OMAP_MPU_UART3_BASE + 8) -#define UART3_EFR (OMAP_MPU_UART3_BASE + 8) -#define UART3_LCR (OMAP_MPU_UART3_BASE + 0x0C) -#define UART3_MCR (OMAP_MPU_UART3_BASE + 0x10) -#define UART3_XON1_ADDR1 (OMAP_MPU_UART3_BASE + 0x10) -#define UART3_XON2_ADDR2 (OMAP_MPU_UART3_BASE + 0x14) -#define UART3_LSR (OMAP_MPU_UART3_BASE + 0x14) -#define UART3_TCR (OMAP_MPU_UART3_BASE + 0x18) -#define UART3_MSR (OMAP_MPU_UART3_BASE + 0x18) -#define UART3_XOFF1 (OMAP_MPU_UART3_BASE + 0x18) -#define UART3_XOFF2 (OMAP_MPU_UART3_BASE + 0x1C) -#define UART3_SPR (OMAP_MPU_UART3_BASE + 0x1C) -#define UART3_TLR (OMAP_MPU_UART3_BASE + 0x1C) -#define UART3_MDR1 (OMAP_MPU_UART3_BASE + 0x20) -#define UART3_MDR2 (OMAP_MPU_UART3_BASE + 0x24) -#define UART3_SFLSR (OMAP_MPU_UART3_BASE + 0x28) -#define UART3_TXFLL (OMAP_MPU_UART3_BASE + 0x28) -#define UART3_RESUME (OMAP_MPU_UART3_BASE + 0x2C) -#define UART3_TXFLH (OMAP_MPU_UART3_BASE + 0x2C) -#define UART3_SFREGL (OMAP_MPU_UART3_BASE + 0x30) -#define UART3_RXFLL (OMAP_MPU_UART3_BASE + 0x30) -#define UART3_SFREGH (OMAP_MPU_UART3_BASE + 0x34) -#define UART3_RXFLH (OMAP_MPU_UART3_BASE + 0x34) -#define UART3_BLR (OMAP_MPU_UART3_BASE + 0x38) -#define UART3_ACREG (OMAP_MPU_UART3_BASE + 0x3C) -#define UART3_DIV16 (OMAP_MPU_UART3_BASE + 0x3C) -#define UART3_SCR (OMAP_MPU_UART3_BASE + 0x40) -#define UART3_SSR (OMAP_MPU_UART3_BASE + 0x44) -#define UART3_EBLR (OMAP_MPU_UART3_BASE + 0x48) -#define UART3_OSC_12M_SEL (OMAP_MPU_UART3_BASE + 0x4C) -#define UART3_MVR (OMAP_MPU_UART3_BASE + 0x50) - -/* - * Configuration Registers - */ -#define FUNC_MUX_CTRL_0 0xfffe1000 -#define FUNC_MUX_CTRL_1 0xfffe1004 -#define FUNC_MUX_CTRL_2 0xfffe1008 -#define COMP_MODE_CTRL_0 0xfffe100c -#define FUNC_MUX_CTRL_3 0xfffe1010 -#define FUNC_MUX_CTRL_4 0xfffe1014 -#define FUNC_MUX_CTRL_5 0xfffe1018 -#define FUNC_MUX_CTRL_6 0xfffe101C -#define FUNC_MUX_CTRL_7 0xfffe1020 -#define FUNC_MUX_CTRL_8 0xfffe1024 -#define FUNC_MUX_CTRL_9 0xfffe1028 -#define FUNC_MUX_CTRL_A 0xfffe102C -#define FUNC_MUX_CTRL_B 0xfffe1030 -#define FUNC_MUX_CTRL_C 0xfffe1034 -#define FUNC_MUX_CTRL_D 0xfffe1038 -#define PULL_DWN_CTRL_0 0xfffe1040 -#define PULL_DWN_CTRL_1 0xfffe1044 -#define PULL_DWN_CTRL_2 0xfffe1048 -#define PULL_DWN_CTRL_3 0xfffe104c -#define GATE_INH_CTRL_0 0xfffe1050 -#define VOLTAGE_CTRL_0 0xfffe1060 -#define TEST_DBG_CTRL_0 0xfffe1070 - -#define MOD_CONF_CTRL_0 0xfffe1080 - -#ifdef CONFIG_OMAP1610 /* 1610 Configuration Register */ - -#define USB_OTG_CTRL 0xFFFB040C -#define USB_TRANSCEIVER_CTRL 0xFFFE1064 -#define PULL_DWN_CTRL_4 0xFFFE10AC -#define PU_PD_SEL_0 0xFFFE10B4 -#define PU_PD_SEL_1 0xFFFE10B8 -#define PU_PD_SEL_2 0xFFFE10BC -#define PU_PD_SEL_3 0xFFFE10C0 -#define PU_PD_SEL_4 0xFFFE10C4 - -#endif -/* - * Traffic Controller Memory Interface Registers - */ -#define TCMIF_BASE 0xfffecc00 -#define IMIF_PRIO (TCMIF_BASE + 0x00) -#define EMIFS_PRIO_REG (TCMIF_BASE + 0x04) -#define EMIFF_PRIO_REG (TCMIF_BASE + 0x08) -#define EMIFS_CONFIG_REG (TCMIF_BASE + 0x0c) -#define EMIFS_CS0_CONFIG (TCMIF_BASE + 0x10) -#define EMIFS_CS1_CONFIG (TCMIF_BASE + 0x14) -#define EMIFS_CS2_CONFIG (TCMIF_BASE + 0x18) -#define EMIFS_CS3_CONFIG (TCMIF_BASE + 0x1c) -#define EMIFF_SDRAM_CONFIG (TCMIF_BASE + 0x20) -#define EMIFF_MRS (TCMIF_BASE + 0x24) -#define TC_TIMEOUT1 (TCMIF_BASE + 0x28) -#define TC_TIMEOUT2 (TCMIF_BASE + 0x2c) -#define TC_TIMEOUT3 (TCMIF_BASE + 0x30) -#define TC_ENDIANISM (TCMIF_BASE + 0x34) -#define EMIFF_SDRAM_CONFIG_2 (TCMIF_BASE + 0x3c) -#define EMIF_CFG_DYNAMIC_WS (TCMIF_BASE + 0x40) - -/* - * LCD Panel - */ -#define TI925_LCD_BASE 0xFFFEC000 -#define TI925_LCD_CONTROL (TI925_LCD_BASE) -#define TI925_LCD_TIMING0 (TI925_LCD_BASE+0x4) -#define TI925_LCD_TIMING1 (TI925_LCD_BASE+0x8) -#define TI925_LCD_TIMING2 (TI925_LCD_BASE+0xc) -#define TI925_LCD_STATUS (TI925_LCD_BASE+0x10) -#define TI925_LCD_SUBPANEL (TI925_LCD_BASE+0x14) - -#define OMAP_LCD_CONTROL TI925_LCD_CONTROL - -/* I2C Registers */ - -#define I2C_BASE 0xfffb3800 - -#define I2C_REV (I2C_BASE + 0x00) -#define I2C_IE (I2C_BASE + 0x04) -#define I2C_STAT (I2C_BASE + 0x08) -#define I2C_IV (I2C_BASE + 0x0c) -#define I2C_BUF (I2C_BASE + 0x14) -#define I2C_CNT (I2C_BASE + 0x18) -#define I2C_DATA (I2C_BASE + 0x1c) -#define I2C_CON (I2C_BASE + 0x24) -#define I2C_OA (I2C_BASE + 0x28) -#define I2C_SA (I2C_BASE + 0x2c) -#define I2C_PSC (I2C_BASE + 0x30) -#define I2C_SCLL (I2C_BASE + 0x34) -#define I2C_SCLH (I2C_BASE + 0x38) -#define I2C_SYSTEST (I2C_BASE + 0x3c) - -/* I2C masks */ - -/* I2C Interrupt Enable Register (I2C_IE): */ - -#define I2C_IE_XRDY_IE (1 << 4) /* Transmit data ready interrupt enable */ -#define I2C_IE_RRDY_IE (1 << 3) /* Receive data ready interrupt enable */ -#define I2C_IE_ARDY_IE (1 << 2) /* Register access ready interrupt enable */ -#define I2C_IE_NACK_IE (1 << 1) /* No acknowledgment interrupt enable */ -#define I2C_IE_AL_IE (1 << 0) /* Arbitration lost interrupt enable */ - -/* I2C Status Register (I2C_STAT): */ - -#define I2C_STAT_SBD (1 << 15) /* Single byte data */ -#define I2C_STAT_BB (1 << 12) /* Bus busy */ -#define I2C_STAT_ROVR (1 << 11) /* Receive overrun */ -#define I2C_STAT_XUDF (1 << 10) /* Transmit underflow */ -#define I2C_STAT_AAS (1 << 9) /* Address as slave */ -#define I2C_STAT_AD0 (1 << 8) /* Address zero */ -#define I2C_STAT_XRDY (1 << 4) /* Transmit data ready */ -#define I2C_STAT_RRDY (1 << 3) /* Receive data ready */ -#define I2C_STAT_ARDY (1 << 2) /* Register access ready */ -#define I2C_STAT_NACK (1 << 1) /* No acknowledgment interrupt enable */ -#define I2C_STAT_AL (1 << 0) /* Arbitration lost interrupt enable */ - -/* I2C Interrupt Vector Register (I2C_IV): */ - -/* I2C Interrupt Code Register (I2C_INTCODE): */ - -#define I2C_INTCODE_MASK 7 -#define I2C_INTCODE_NONE 0 -#define I2C_INTCODE_AL 1 /* Arbitration lost */ -#define I2C_INTCODE_NAK 2 /* No acknowledgement/general call */ -#define I2C_INTCODE_ARDY 3 /* Register access ready */ -#define I2C_INTCODE_RRDY 4 /* Rcv data ready */ -#define I2C_INTCODE_XRDY 5 /* Xmit data ready */ - -/* I2C Buffer Configuration Register (I2C_BUF): */ - -#define I2C_BUF_RDMA_EN (1 << 15) /* Receive DMA channel enable */ -#define I2C_BUF_XDMA_EN (1 << 7) /* Transmit DMA channel enable */ - -/* I2C Configuration Register (I2C_CON): */ - -#define I2C_CON_EN (1 << 15) /* I2C module enable */ -#define I2C_CON_BE (1 << 14) /* Big endian mode */ -#define I2C_CON_STB (1 << 11) /* Start byte mode (master mode only) */ -#define I2C_CON_MST (1 << 10) /* Master/slave mode */ -#define I2C_CON_TRX (1 << 9) /* Transmitter/receiver mode (master mode only) */ -#define I2C_CON_XA (1 << 8) /* Expand address */ -#define I2C_CON_RM (1 << 2) /* Repeat mode (master mode only) */ -#define I2C_CON_STP (1 << 1) /* Stop condition (master mode only) */ -#define I2C_CON_STT (1 << 0) /* Start condition (master mode only) */ - -/* I2C System Test Register (I2C_SYSTEST): */ - -#define I2C_SYSTEST_ST_EN (1 << 15) /* System test enable */ -#define I2C_SYSTEST_FREE (1 << 14) /* Free running mode (on breakpoint) */ -#define I2C_SYSTEST_TMODE_MASK (3 << 12) /* Test mode select */ -#define I2C_SYSTEST_TMODE_SHIFT (12) /* Test mode select */ -#define I2C_SYSTEST_SCL_I (1 << 3) /* SCL line sense input value */ -#define I2C_SYSTEST_SCL_O (1 << 2) /* SCL line drive output value */ -#define I2C_SYSTEST_SDA_I (1 << 1) /* SDA line sense input value */ -#define I2C_SYSTEST_SDA_O (1 << 0) /* SDA line drive output value */ - -/* - * MMC/SD Host Controller Registers - */ - -#define OMAP_MMC_CMD 0xFFFB7800 /* MMC Command */ -#define OMAP_MMC_ARGL 0xFFFB7804 /* MMC argument low */ -#define OMAP_MMC_ARGH 0xFFFB7808 /* MMC argument high */ -#define OMAP_MMC_CON 0xFFFB780C /* MMC system configuration */ -#define OMAP_MMC_STAT 0xFFFB7810 /* MMC status */ -#define OMAP_MMC_IE 0xFFFB7814 /* MMC system interrupt enable */ -#define OMAP_MMC_CTO 0xFFFB7818 /* MMC command time-out */ -#define OMAP_MMC_DTO 0xFFFB781C /* MMC data time-out */ -#define OMAP_MMC_DATA 0xFFFB7820 /* MMC TX/RX FIFO data */ -#define OMAP_MMC_BLEN 0xFFFB7824 /* MMC block length */ -#define OMAP_MMC_NBLK 0xFFFB7828 /* MMC number of blocks */ -#define OMAP_MMC_BUF 0xFFFB782C /* MMC buffer configuration */ -#define OMAP_MMC_SPI 0xFFFB7830 /* MMC serial port interface */ -#define OMAP_MMC_SDIO 0xFFFB7834 /* MMC SDIO mode configuration */ -#define OMAP_MMC_SYST 0xFFFB7838 /* MMC system test */ -#define OMAP_MMC_REV 0xFFFB783C /* MMC module version */ -#define OMAP_MMC_RSP0 0xFFFB7840 /* MMC command response 0 */ -#define OMAP_MMC_RSP1 0xFFFB7844 /* MMC command response 1 */ -#define OMAP_MMC_RSP2 0xFFFB7848 /* MMC command response 2 */ -#define OMAP_MMC_RSP3 0xFFFB784C /* MMC command response 3 */ -#define OMAP_MMC_RSP4 0xFFFB7850 /* MMC command response 4 */ -#define OMAP_MMC_RSP5 0xFFFB7854 /* MMC command response 5 */ -#define OMAP_MMC_RSP6 0xFFFB7858 /* MMC command response 6 */ -#define OMAP_MMC_RSP7 0xFFFB785C /* MMC command response 4 */ - -/* MMC masks */ - -#define OMAP_MMC_END_OF_CMD (1 << 0) /* End of command phase */ -#define OMAP_MMC_CARD_BUSY (1 << 2) /* Card enter busy state */ -#define OMAP_MMC_BLOCK_RS (1 << 3) /* Block received/sent */ -#define OMAP_MMC_EOF_BUSY (1 << 4) /* Card exit busy state */ -#define OMAP_MMC_DATA_TIMEOUT (1 << 5) /* Data response time-out */ -#define OMAP_MMC_DATA_CRC (1 << 6) /* Date CRC error */ -#define OMAP_MMC_CMD_TIMEOUT (1 << 7) /* Command response time-out */ -#define OMAP_MMC_CMD_CRC (1 << 8) /* Command CRC error */ -#define OMAP_MMC_A_FULL (1 << 10) /* Buffer almost full */ -#define OMAP_MMC_A_EMPTY (1 << 11) /* Buffer almost empty */ -#define OMAP_MMC_OCR_BUSY (1 << 12) /* OCR busy */ -#define OMAP_MMC_CARD_IRQ (1 << 13) /* Card IRQ received */ -#define OMAP_MMC_CARD_ERR (1 << 14) /* Card status error in response */ - -/* 2.9.2 MPUI Interface Registers FFFE:C900 */ - -#define MPUI_CTRL_REG (volatile __u32 *)(0xfffec900) -#define MPUI_DEBUG_ADDR (volatile __u32 *)(0xfffec904) -#define MPUI_DEBUG_DATA (volatile __u32 *)(0xfffec908) -#define MPUI_DEBUG_FLAG (volatile __u16 *)(0xfffec90c) -#define MPUI_STATUS_REG (volatile __u16 *)(0xfffec910) -#define MPUI_DSP_STATUS_REG (volatile __u16 *)(0xfffec914) -#define MPUI_DSP_BOOT_CONFIG (volatile __u16 *)(0xfffec918) -#define MPUI_DSP_API_CONFIG (volatile __u16 *)(0xfffec91c) - -/* 2.9.6 Traffic Controller Memory Interface Registers: */ -#define OMAP_IMIF_PRIO_REG 0xfffecc00 -#define OMAP_EMIFS_PRIO_REG 0xfffecc04 -#define OMAP_EMIFF_PRIO_REG 0xfffecc08 -#define OMAP_EMIFS_CONFIG_REG 0xfffecc0c -#define OMAP_EMIFS_CS0_CONFIG 0xfffecc10 -#define OMAP_EMIFS_CS1_CONFIG 0xfffecc14 -#define OMAP_EMIFS_CS2_CONFIG 0xfffecc18 -#define OMAP_EMIFS_CS3_CONFIG 0xfffecc1c -#define OMAP_EMIFF_SDRAM_CONFIG 0xfffecc20 -#define OMAP_EMIFF_MRS 0xfffecc24 -#define OMAP_TIMEOUT1 0xfffecc28 -#define OMAP_TIMEOUT2 0xfffecc2c -#define OMAP_TIMEOUT3 0xfffecc30 -#define OMAP_ENDIANISM 0xfffecc34 - -/* 2.9.10 EMIF Slow Interface Configuration Register (EMIFS_CONFIG_REG): */ -#define OMAP_EMIFS_CONFIG_FR (1 << 4) -#define OMAP_EMIFS_CONFIG_PDE (1 << 3) -#define OMAP_EMIFS_CONFIG_PWD_EN (1 << 2) -#define OMAP_EMIFS_CONFIG_BM (1 << 1) -#define OMAP_EMIFS_CONFIG_WP (1 << 0) - -/* - * Memory chunk set aside for the Framebuffer in SRAM - */ -#define SRAM_FRAMEBUFFER_MEMORY OMAP1510_SRAM_BASE - - -/* - * DMA - */ - -#define OMAP1510_DMA_BASE 0xFFFED800 -#define OMAP_DMA_BASE OMAP1510_DMA_BASE - -/* Global Register selection */ -#define NO_GLOBAL_DMA_ACCESS 0 - -/* Channel select field - * NOTE: all other channels are linear, chan0 is 0, chan1 is 1, etc... - */ -#define LCD_CHANNEL 0xc - -/* Register Select Field (LCD) */ -#define DMA_LCD_CTRL 0 -#define DMA_LCD_TOP_F1_L 1 -#define DMA_LCD_TOP_F1_U 2 -#define DMA_LCD_BOT_F1_L 3 -#define DMA_LCD_BOT_F1_U 4 - -#define LCD_FRAME_MODE (1<<0) -#define LCD_FRAME_IT_IE (1<<1) -#define LCD_BUS_ERROR_IT_IE (1<<2) -#define LCD_FRAME_1_IT_COND (1<<3) -#define LCD_FRAME_2_IT_COND (1<<4) -#define LCD_BUS_ERROR_IT_COND (1<<5) -#define LCD_SOURCE_IMIF (1<<6) - -/* - * Real-Time Clock - */ - -#define RTC_SECONDS (volatile __u8 *)(OMAP1510_RTC_BASE + 0x00) -#define RTC_MINUTES (volatile __u8 *)(OMAP1510_RTC_BASE + 0x04) -#define RTC_HOURS (volatile __u8 *)(OMAP1510_RTC_BASE + 0x08) -#define RTC_DAYS (volatile __u8 *)(OMAP1510_RTC_BASE + 0x0C) -#define RTC_MONTHS (volatile __u8 *)(OMAP1510_RTC_BASE + 0x10) -#define RTC_YEARS (volatile __u8 *)(OMAP1510_RTC_BASE + 0x14) -#define RTC_CTRL (volatile __u8 *)(OMAP1510_RTC_BASE + 0x40) - - -/* --------------------------------------------------------------------------- - * OMAP1510 Interrupt Handlers - * --------------------------------------------------------------------------- - * - */ -#define OMAP_IH1_BASE 0xfffecb00 -#define OMAP_IH2_BASE 0xfffe0000 -#define OMAP1510_ITR 0x0 -#define OMAP1510_MASK 0x4 - -#define INTERRUPT_HANDLER_BASE OMAP_IH1_BASE -#define INTERRUPT_INPUT_REGISTER OMAP1510_ITR -#define INTERRUPT_MASK_REGISTER OMAP1510_MASK - - -/* --------------------------------------------------------------------------- - * OMAP1510 TIMERS - * --------------------------------------------------------------------------- - * - */ - -#define OMAP1510_32kHz_TIMER_BASE 0xfffb9000 - -/* 32k Timer Registers */ -#define TIMER32k_CR 0x08 -#define TIMER32k_TVR 0x00 -#define TIMER32k_TCR 0x04 - -/* 32k Timer Control Register definition */ -#define TIMER32k_TSS (1<<0) -#define TIMER32k_TRB (1<<1) -#define TIMER32k_INT (1<<2) -#define TIMER32k_ARL (1<<3) - -/* MPU Timer base addresses */ -#define OMAP1510_MPUTIMER_BASE 0xfffec500 -#define OMAP1510_MPUTIMER_OFF 0x00000100 - -#define OMAP1510_TIMER1_BASE 0xfffec500 -#define OMAP1510_TIMER2_BASE 0xfffec600 -#define OMAP1510_TIMER3_BASE 0xfffec700 - -/* MPU Timer Registers */ -#define CNTL_TIMER 0 -#define LOAD_TIM 4 -#define READ_TIM 8 - -/* CNTL_TIMER register bits */ -#define MPUTIM_FREE (1<<6) -#define MPUTIM_CLOCK_ENABLE (1<<5) -#define MPUTIM_PTV_MASK (0x7<<MPUTIM_PTV_BIT) -#define MPUTIM_PTV_BIT 2 -#define MPUTIM_AR (1<<1) -#define MPUTIM_ST (1<<0) - -/* --------------------------------------------------------------------------- - * OMAP1510 GPIO (SHARED) - * --------------------------------------------------------------------------- - * - */ -#define GPIO_DATA_INPUT_REG (OMAP1510_GPIO_BASE + 0x0) -#define GPIO_DATA_OUTPUT_REG (OMAP1510_GPIO_BASE + 0x4) -#define GPIO_DIR_CONTROL_REG (OMAP1510_GPIO_BASE + 0x8) -#define GPIO_INT_CONTROL_REG (OMAP1510_GPIO_BASE + 0xc) -#define GPIO_INT_MASK_REG (OMAP1510_GPIO_BASE + 0x10) -#define GPIO_INT_STATUS_REG (OMAP1510_GPIO_BASE + 0x14) -#define GPIO_PIN_CONTROL_REG (OMAP1510_GPIO_BASE + 0x18) - - -/* --------------------------- - * OMAP1510 MPUIO (ARM only) - *---------------------------- - */ -#define OMAP1510_MPUIO_BASE 0xFFFB5000 -#define MPUIO_DATA_INPUT_REG (OMAP1510_MPUIO_BASE + 0x0) -#define MPUIO_DATA_OUTPUT_REG (OMAP1510_MPUIO_BASE + 0x4) -#define MPUIO_DIR_CONTROL_REG (OMAP1510_MPUIO_BASE + 0x8) - -/* --------------------------------------------------------------------------- - * OMAP1510 TIPB (only) - * --------------------------------------------------------------------------- - * - */ -#define TIPB_PUBLIC_CNTL_BASE 0xfffed300 -#define MPU_PUBLIC_TIPB_CNTL_REG (TIPB_PUBLIC_CNTL_BASE + 0x8) -#define TIPB_PRIVATE_CNTL_BASE 0xfffeca00 -#define MPU_PRIVATE_TIPB_CNTL_REG (TIPB_PRIVATE_CNTL_BASE + 0x8) - -/* - * --------------------------------------------------------------------------- - * OMAP1510 Camera Interface - * --------------------------------------------------------------------------- - */ -#define CAMERA_BASE (IO_BASE + 0x6800) -#define CAM_CTRLCLOCK_REG (CAMERA_BASE + 0x00) -#define CAM_IT_STATUS_REG (CAMERA_BASE + 0x04) -#define CAM_MODE_REG (CAMERA_BASE + 0x08) -#define CAM_STATUS_REG (CAMERA_BASE + 0x0C) -#define CAM_CAMDATA_REG (CAMERA_BASE + 0x10) -#define CAM_GPIO_REG (CAMERA_BASE + 0x14) -#define CAM_PEAK_CTR_REG (CAMERA_BASE + 0x18) - -#if 0 -#ifndef __ASSEMBLY__ -typedef struct { - __u32 ctrlclock; - __u32 it_status; - __u32 mode; - __u32 status; - __u32 camdata; - __u32 gpio; - __u32 peak_counter; -} camera_regs_t; -#endif -#endif - -/* CTRLCLOCK bit shifts */ -#define FOSCMOD_BIT 0 -#define FOSCMOD_MASK (0x7 << FOSCMOD_BIT) -#define FOSCMOD_12MHz 0x0 -#define FOSCMOD_6MHz 0x2 -#define FOSCMOD_9_6MHz 0x4 -#define FOSCMOD_24MHz 0x5 -#define FOSCMOD_8MHz 0x6 -#define POLCLK (1<<3) -#define CAMEXCLK_EN (1<<4) -#define MCLK_EN (1<<5) -#define DPLL_EN (1<<6) -#define LCLK_EN (1<<7) - -/* IT_STATUS bit shifts */ -#define V_UP (1<<0) -#define V_DOWN (1<<1) -#define H_UP (1<<2) -#define H_DOWN (1<<3) -#define FIFO_FULL (1<<4) -#define DATA_XFER (1<<5) - -/* MODE bit shifts */ -#define CAMOSC (1<<0) -#define IMGSIZE_BIT 1 -#define IMGSIZE_MASK (0x3 << IMGSIZE_BIT) -#define IMGSIZE_CIF (0x0 << IMGSIZE_BIT) /* 352x288 */ -#define IMGSIZE_QCIF (0x1 << IMGSIZE_BIT) /* 176x144 */ -#define IMGSIZE_VGA (0x2 << IMGSIZE_BIT) /* 640x480 */ -#define IMGSIZE_QVGA (0x3 << IMGSIZE_BIT) /* 320x240 */ -#define ORDERCAMD (1<<3) -#define EN_V_UP (1<<4) -#define EN_V_DOWN (1<<5) -#define EN_H_UP (1<<6) -#define EN_H_DOWN (1<<7) -#define EN_DMA (1<<8) -#define THRESHOLD (1<<9) -#define THRESHOLD_BIT 9 -#define THRESHOLD_MASK (0x7f<<9) -#define EN_NIRQ (1<<16) -#define EN_FIFO_FULL (1<<17) -#define RAZ_FIFO (1<<18) - -/* STATUS bit shifts */ -#define VSTATUS (1<<0) -#define HSTATUS (1<<1) - -/* GPIO bit shifts */ -#define CAM_RST (1<<0) - - -/********************* - * Watchdog timer. - *********************/ -#define WDTIM_BASE 0xfffec800 -#define WDTIM_CONTROL (WDTIM_BASE+0x00) -#define WDTIM_LOAD (WDTIM_BASE+0x04) -#define WDTIM_READ (WDTIM_BASE+0x04) -#define WDTIM_MODE (WDTIM_BASE+0x08) - -/* Values to write to mode register to disable the watchdog function. */ -#define DISABLE_SEQ1 0xF5 -#define DISABLE_SEQ2 0xA0 - -/* WDTIM_CONTROL bit definitions. */ -#define WDTIM_CONTROL_ST BIT7 - - -/* --------------------------------------------------------------------------- - * Differentiating processor versions for those who care. - * --------------------------------------------------------------------------- - * - */ -#define OMAP1509 0 -#define OMAP1510 1 - -#define OMAP1510_ID_CODE_REG 0xfffed404 - -#ifndef __ASSEMBLY__ -int cpu_type(void); -#endif - -/*****************************************************************************/ - -#define CLKGEN_RESET_BASE (0xfffece00) -#define ARM_CKCTL (volatile __u16 *)(CLKGEN_RESET_BASE + 0x0) -#define ARM_IDLECT1 (volatile __u16 *)(CLKGEN_RESET_BASE + 0x4) -#define ARM_IDLECT2 (volatile __u16 *)(CLKGEN_RESET_BASE + 0x8) -#define ARM_EWUPCT (volatile __u16 *)(CLKGEN_RESET_BASE + 0xC) -#define ARM_RSTCT1 (volatile __u16 *)(CLKGEN_RESET_BASE + 0x10) -#define ARM_RSTCT2 (volatile __u16 *)(CLKGEN_RESET_BASE + 0x14) -#define ARM_SYSST (volatile __u16 *)(CLKGEN_RESET_BASE + 0x18) - - -#define CK_CLKIN 12 /* MHz */ -#define CK_RATEF 1 -#define CK_IDLEF 2 -#define CK_ENABLEF 4 -#define CK_SELECTF 8 -#ifndef __ASSEMBLER__ -#define CK_DPLL1 ((volatile __u16 *)0xfffecf00) -#else -#define CK_DPLL1 (0xfffecf00) -#endif -#define SETARM_IDLE_SHIFT - -/* ARM_CKCTL bit shifts */ -#define PERDIV 0 -#define LCDDIV 2 -#define ARMDIV 4 -#define DSPDIV 6 -#define TCDIV 8 -#define DSPMMUDIV 10 -#define ARM_TIMXO 12 -#define EN_DSPCK 13 -#define ARM_INTHCK_SEL 14 /* REVISIT -- where is this used? */ - -#define ARM_CKCTL_RSRVD_BIT15 (1 << 15) -#define ARM_CKCTL_ARM_INTHCK_SEL (1 << 14) -#define ARM_CKCTL_EN_DSPCK (1 << 13) -#define ARM_CKCTL_ARM_TIMXO (1 << 12) -#define ARM_CKCTL_DSPMMU_DIV1 (1 << 11) -#define ARM_CKCTL_DSPMMU_DIV2 (1 << 10) -#define ARM_CKCTL_TCDIV1 (1 << 9) -#define ARM_CKCTL_TCDIV2 (1 << 8) -#define ARM_CKCTL_DSPDIV1 (1 << 7) -#define ARM_CKCTL_DSPDIV0 (1 << 6) -#define ARM_CKCTL_ARMDIV1 (1 << 5) -#define ARM_CKCTL_ARMDIV0 (1 << 4) -#define ARM_CKCTL_LCDDIV1 (1 << 3) -#define ARM_CKCTL_LCDDIV0 (1 << 2) -#define ARM_CKCTL_PERDIV1 (1 << 1) -#define ARM_CKCTL_PERDIV0 (1 << 0) - -/* ARM_IDLECT1 bit shifts */ -#define IDLWDT_ARM 0 -#define IDLXORP_ARM 1 -#define IDLPER_ARM 2 -#define IDLLCD_ARM 3 -#define IDLLB_ARM 4 -#define IDLHSAB_ARM 5 -#define IDLIF_ARM 6 -#define IDLDPLL_ARM 7 -#define IDLAPI_ARM 8 -#define IDLTIM_ARM 9 -#define SETARM_IDLE 11 - -/* ARM_IDLECT2 bit shifts */ -#define EN_WDTCK 0 -#define EN_XORPCK 1 -#define EN_PERCK 2 -#define EN_LCDCK 3 -#define EN_LBCK 4 -#define EN_HSABCK 5 -#define EN_APICK 6 -#define EN_TIMCK 7 -#define DMACK_REQ 8 -#define EN_GPIOCK 9 -#define EN_LBFREECK 10 - -#define ARM_RSTCT1_SW_RST (1 << 3) -#define ARM_RSTCT1_DSP_RST (1 << 2) -#define ARM_RSTCT1_DSP_EN (1 << 1) -#define ARM_RSTCT1_ARM_RST (1 << 0) - -/* ARM_RSTCT2 bit shifts */ -#define EN_PER 0 - -#define ARM_SYSST_RSRVD_BIT15 (1 << 15) -#define ARM_SYSST_RSRVD_BIT14 (1 << 14) -#define ARM_SYSST_CLOCK_SELECT2 (1 << 13) -#define ARM_SYSST_CLOCK_SELECT1 (1 << 12) -#define ARM_SYSST_CLOCK_SELECT0 (1 << 11) -#define ARM_SYSST_RSRVD_BIT10 (1 << 10) -#define ARM_SYSST_RSRVD_BIT9 (1 << 9) -#define ARM_SYSST_RSRVD_BIT8 (1 << 8) -#define ARM_SYSST_RSRVD_BIT7 (1 << 7) -#define ARM_SYSST_IDLE_DSP (1 << 6) -#define ARM_SYSST_POR (1 << 5) -#define ARM_SYSST_EXT_RST (1 << 4) -#define ARM_SYSST_ARM_MCRST (1 << 3) -#define ARM_SYSST_ARM_WDRST (1 << 2) -#define ARM_SYSST_GLOB_SWRST (1 << 1) -#define ARM_SYSST_DSP_WDRST (1 << 0) - -/* Table 15-23. DPLL Control Registers: */ -#define DPLL_CTL_REG (volatile __u16 *)(0xfffecf00) - -/* Table 15-24. Control Register (CTL_REG): */ - -#define DPLL_CTL_REG_IOB (1 << 13) -#define DPLL_CTL_REG_PLL_MULT Fld(5,0) - -/*****************************************************************************/ - -/* OMAP INTERRUPT REGISTERS */ -#define IRQ_ITR 0x00 -#define IRQ_MIR 0x04 -#define IRQ_SIR_IRQ 0x10 -#define IRQ_SIR_FIQ 0x14 -#define IRQ_CONTROL_REG 0x18 -#define IRQ_ISR 0x9c -#define IRQ_ILR0 0x1c - -#define REG_IHL1_MIR (OMAP_IH1_BASE+IRQ_MIR) -#define REG_IHL2_MIR (OMAP_IH2_BASE+IRQ_MIR) - -/* INTERRUPT LEVEL REGISTER BITS */ -#define ILR_PRIORITY_MASK (0x3c) -#define ILR_PRIORITY_SHIFT (2) -#define ILR_LEVEL_TRIGGER (1<<1) -#define ILR_FIQ (1<<0) - -#define IRQ_LEVEL_INT 1 -#define IRQ_EDGE_INT 0 - -/* Macros to access registers */ -#define outb(v,p) *(volatile u8 *) (p) = v -#define outw(v,p) *(volatile u16 *) (p) = v -#define outl(v,p) *(volatile u32 *) (p) = v - -#define inb(p) *(volatile u8 *) (p) -#define inw(p) *(volatile u16 *) (p) -#define inl(p) *(volatile u32 *) (p) diff --git a/include/configs/omap5912osk.h b/include/configs/omap5912osk.h deleted file mode 100644 index 376dfdb..0000000 --- a/include/configs/omap5912osk.h +++ /dev/null @@ -1,174 +0,0 @@ -/* - * (C) Copyright 2003 - * Texas Instruments. - * Kshitij Gupta <kshitij@ti.com> - * Configuation settings for the TI OMAP Innovator board. - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/* - * High Level Configuration Options - * (easy to change) - */ -#define CONFIG_ARM926EJS 1 /* This is an arm926ejs CPU core */ -#define CONFIG_OMAP 1 /* in a TI OMAP core */ -#define CONFIG_OMAP1610 1 /* 5912 is same as 1610 */ -#define CONFIG_OSK_OMAP5912 1 /* a OSK Board */ - -#define CONFIG_DISPLAY_CPUINFO 1 /* display cpu info (and speed) */ -#define CONFIG_DISPLAY_BOARDINFO 1 /* display board info */ - -/* input clock of PLL */ -/* the OMAP5912 OSK has 12MHz input clock */ -#define CONFIG_SYS_CLK_FREQ 12000000 - -#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */ -#define CONFIG_SETUP_MEMORY_TAGS 1 -#define CONFIG_INITRD_TAG 1 /* Required for ramdisk support */ - -/* - * Size of malloc() pool - */ -#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 128*1024) - -/* - * Hardware drivers - */ -/* -*/ -#define CONFIG_LAN91C96 -#define CONFIG_LAN91C96_BASE 0x04800300 -#define CONFIG_LAN91C96_EXT_PHY - -/* - * NS16550 Configuration - */ -#define CONFIG_SYS_NS16550 -#define CONFIG_SYS_NS16550_SERIAL -#define CONFIG_SYS_NS16550_REG_SIZE (-4) -#define CONFIG_SYS_NS16550_CLK (48000000) /* can be 12M/32Khz or 48Mhz */ -#define CONFIG_SYS_NS16550_COM1 0xfffb0000 /* uart1, bluetooth uart - on helen */ - -/* - * select serial console configuration - */ -#define CONFIG_SERIAL1 1 /* we use SERIAL 1 on OMAP5912 OSK */ - -/* allow to overwrite serial and ethaddr */ -#define CONFIG_ENV_OVERWRITE -#define CONFIG_CONS_INDEX 1 -#define CONFIG_BAUDRATE 115200 - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_DHCP - - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_SUBNETMASK -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME -#define CONFIG_BOOTP_BOOTPATH - - -#include <configs/omap1510.h> - -#define CONFIG_BOOTDELAY 3 -#define CONFIG_BOOTARGS "mem=32M console=ttyS0,115200n8 noinitrd \ - root=/dev/nfs rw nfsroot=157.87.82.48:\ - /home/mwd/myfs/target ip=dhcp" -#define CONFIG_NETMASK 255.255.254.0 /* talk on MY local net */ -#define CONFIG_IPADDR 156.117.97.156 /* static IP I currently own */ -#define CONFIG_SERVERIP 156.117.97.139 /* current IP of my dev pc */ -#define CONFIG_BOOTFILE "uImage" /* file to load */ - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_KGDB_BAUDRATE 115200 /* speed to run kgdb serial port */ -#endif - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_LONGHELP /* undef to save memory */ -#define CONFIG_SYS_PROMPT "OMAP5912 OSK # " /* Monitor Command Prompt */ -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -/* Print Buffer Size */ -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ - -#define CONFIG_SYS_MEMTEST_START 0x10000000 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END 0x12000000 /* 32 MB in DRAM */ - -#define CONFIG_SYS_LOAD_ADDR 0x10000000 /* default load address */ - -/* The 1610 has 6 timers, they can be driven by the RefClk (12Mhz) or by - * DPLL1. This time is further subdivided by a local divisor. - */ -#define CONFIG_SYS_TIMERBASE 0xFFFEC500 /* use timer 1 */ -#define CONFIG_SYS_PTV 7 /* 2^(PTV+1), divide by 256 */ - -/*----------------------------------------------------------------------- - * Physical Memory Map - */ -#define CONFIG_NR_DRAM_BANKS 1 /* we have 1 bank of DRAM */ -#define PHYS_SDRAM_1 0x10000000 /* SDRAM Bank #1 */ -#define PHYS_SDRAM_1_SIZE 0x02000000 /* 32 MB */ - -#define PHYS_FLASH_1 0x00000000 /* Flash Bank #1 */ -#define PHYS_FLASH_2 0x01000000 /* Flash Bank #2 */ - -#define CONFIG_SYS_FLASH_BASE PHYS_FLASH_1 - -#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE /* Monitor at beginning of flash */ - -#define PHYS_SRAM 0x20000000 - -/*----------------------------------------------------------------------- - * FLASH driver setup - */ -#define CONFIG_SYS_FLASH_CFI 1 /* Flash memory is CFI compliant */ -#define CONFIG_FLASH_CFI_DRIVER 1 /* Use drivers/mtd/cfi_flash.c */ - -#define CONFIG_SYS_FLASH_BANKS_LIST { PHYS_FLASH_1, PHYS_FLASH_2 } - -#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of memory banks */ -#define PHYS_FLASH_SIZE 0x02000000 /* 32MB */ -#define CONFIG_SYS_MAX_FLASH_SECT (259) /* max number of sectors on one chip */ - -#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* Use buffered writes (~10x faster) */ -#define CONFIG_SYS_FLASH_PROTECTION 1 /* Use hardware sector protection */ - -#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */ - -/* timeout values are in ticks */ -#define CONFIG_SYS_FLASH_ERASE_TOUT (20*CONFIG_SYS_HZ) /* Timeout for Flash Erase */ -#define CONFIG_SYS_FLASH_WRITE_TOUT (20*CONFIG_SYS_HZ) /* Timeout for Flash Write */ - -/*----------------------------------------------------------------------- - * FLASH and environment organization - */ -#define CONFIG_ENV_IS_IN_FLASH 1 -/* addr of environment */ -#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + CONFIG_ENV_OFFSET) - -#define CONFIG_ENV_SIZE 0x20000 /* Total Size of Environment Sector */ -#define CONFIG_ENV_OFFSET 0x40000 /* environment starts here */ - -#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1 -#define CONFIG_SYS_INIT_RAM_ADDR PHYS_SRAM -#define CONFIG_SYS_INIT_RAM_SIZE (250 * 1024) -#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + \ - CONFIG_SYS_INIT_RAM_SIZE) - -#endif /* __CONFIG_H */ |