diff options
Diffstat (limited to 'include')
| -rw-r--r-- | include/commproc.h | 32 | ||||
| -rw-r--r-- | include/configs/GTH.h | 389 |
2 files changed, 0 insertions, 421 deletions
diff --git a/include/commproc.h b/include/commproc.h index 9d28abc..762238e 100644 --- a/include/commproc.h +++ b/include/commproc.h @@ -828,38 +828,6 @@ typedef struct scc_enet { #endif /* CONFIG_GENIETV */ -/*** GTH ******************************************************/ - -#ifdef CONFIG_GTH -#ifdef CONFIG_FEC_ENET -#define FEC_ENET /* use FEC for EThernet */ -#endif /* CONFIG_FEC_ETHERNET */ - -/* This ENET stuff is for GTH 10 Mbit ( SCC ) */ -#define PROFF_ENET PROFF_SCC1 -#define CPM_CR_ENET CPM_CR_CH_SCC1 -#define SCC_ENET 0 - -#define PA_ENET_RXD ((ushort)0x0001) /* PA15 */ -#define PA_ENET_TXD ((ushort)0x0002) /* PA14 */ -#define PA_ENET_TCLK ((ushort)0x0800) /* PA4 */ -#define PA_ENET_RCLK ((ushort)0x0400) /* PA5 */ - -#define PB_ENET_TENA ((uint)0x00001000) /* PB19 */ - -#define PC_ENET_CLSN ((ushort)0x0010) /* PC11 */ -#define PC_ENET_RENA ((ushort)0x0020) /* PC10 */ - -/* NOTE. This is reset for 10Mbit port only */ -#define PC_ENET_RESET ((ushort)0x0100) /* PC 7 */ - -#define SICR_ENET_MASK ((uint)0x000000ff) - -/* TCLK PA4 -->CLK4, RCLK PA5 -->CLK3 */ -#define SICR_ENET_CLKRT ((uint)0x00000037) - -#endif /* CONFIG_GTH */ - /*** HERMES-PRO ******************************************************/ /* The HERMES-PRO uses the FEC on a MPC860T for Ethernet */ diff --git a/include/configs/GTH.h b/include/configs/GTH.h deleted file mode 100644 index c2cf852..0000000 --- a/include/configs/GTH.h +++ /dev/null @@ -1,389 +0,0 @@ -/* - * Parameters for GTH board - * Based on FADS860T - * by thomas.lange@corelatus.com - - * A collection of structures, addresses, and values associated with - * the Motorola 860T FADS board. Copied from the MBX stuff. - * Magnus Damm added defines for 8xxrom and extended bd_info. - * Helmut Buchsbaum added bitvalues for BCSRx - * - * Copyright (c) 1998 Dan Malek (dmalek@jlc.net) - */ - -/* - * ff000000 -> ff00ffff : IMAP internal in the cpu - * e0000000 -> ennnnnnn : pcmcia - * 98000000 -> 983nnnnn : FPGA 4MB - * 90000000 -> 903nnnnn : FPGA 4MB - * 80000000 -> 80nnnnnn : flash connected to CS0, final ( real ) location - * 00000000 -> nnnnnnnn : sdram - */ - -/* ------------------------------------------------------------------------- */ - -/* - * board/config.h - configuration options, board specific - */ - -#ifndef __CONFIG_H -#define __CONFIG_H - -/* - * High Level Configuration Options - * (easy to change) - */ -#include <mpc8xx_irq.h> - -#define CONFIG_MPC860 1 -#define CONFIG_MPC860T 1 -#define CONFIG_GTH 1 - -#define CONFIG_MISC_INIT_R 1 - -#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */ -#undef CONFIG_8xx_CONS_SMC2 -#undef CONFIG_8xx_CONS_NONE -#define CONFIG_BAUDRATE 9600 -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ - -#define MPC8XX_FACT 3 /* Multiply by 3 */ -#define MPC8XX_XIN 16384000 /* 16.384 MHz */ -#define MPC8XX_HZ ((MPC8XX_XIN) * (MPC8XX_FACT)) - -#define CONFIG_BOOTDELAY 1 /* autoboot after 0 seconds */ - -#define CONFIG_ENV_OVERWRITE 1 /* Allow change of ethernet address */ - -#define CONFIG_BOOT_RETRY_TIME 5 /* Retry boot in 5 secs */ - -#define CONFIG_RESET_TO_RETRY 1 /* If timeout waiting for command, perform a reset */ - -/* Only interrupt boot if space is pressed */ -/* If a long serial cable is connected but */ -/* other end is dead, garbage will be read */ -#define CONFIG_AUTOBOOT_KEYED 1 -#define CONFIG_AUTOBOOT_PROMPT \ - "Press space to abort autoboot in %d second\n", bootdelay -#define CONFIG_AUTOBOOT_DELAY_STR "d" -#define CONFIG_AUTOBOOT_STOP_STR " " - -#if 0 -/* Net boot */ -/* Loads a tftp image and starts it */ -#define CONFIG_BOOTCOMMAND "bootp;bootm 100000" /* autoboot command */ -#define CONFIG_BOOTARGS "panic=1" -#else -/* Compact flash boot */ -#define CONFIG_BOOTARGS "panic=1 root=/dev/hda7" -#define CONFIG_BOOTCOMMAND "disk 100000 0:5;bootm 100000" -#endif - -/* Enable watchdog */ -#define CONFIG_WATCHDOG 1 - -/* choose SCC1 ethernet (10BASET on motherboard) - * or FEC ethernet (10/100 on daughterboard) - */ -#if 1 -#define CONFIG_SCC1_ENET 1 /* use SCC1 ethernet */ -#undef CONFIG_FEC_ENET /* disable FEC ethernet */ -#define CONFIG_SYS_DISCOVER_PHY -#else -#undef CONFIG_SCC1_ENET /* disable SCC1 ethernet */ -#define CONFIG_FEC_ENET 1 /* use FEC ethernet */ -#define CONFIG_SYS_DISCOVER_PHY -#endif -#if defined(CONFIG_SCC1_ENET) && defined(CONFIG_FEC_ENET) -#error Both CONFIG_SCC1_ENET and CONFIG_FEC_ENET configured -#endif - - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - - -/* - * Command line configuration. - */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_IDE - - -#define CONFIG_MAC_PARTITION -#define CONFIG_DOS_PARTITION - -/* - * Miscellaneous configurable options - */ -#define CONFIG_SYS_PROMPT "=>" /* Monitor Command Prompt */ -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ -#define CONFIG_SYS_MAXARGS 16 /* max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ - -#define CONFIG_SYS_MEMTEST_START 0x0100000 /* memtest works on */ -#define CONFIG_SYS_MEMTEST_END 0x0400000 /* 1 ... 4 MB in DRAM */ - -/* Default location to load data from net */ -#define CONFIG_SYS_LOAD_ADDR 0x100000 - -#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */ - -#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400 } - -/* - * Low Level Configuration Settings - * (address mappings, register initial values, etc.) - * You should know what you are doing if you make changes here. - */ -/*----------------------------------------------------------------------- - * Internal Memory Mapped Register - */ -#define CONFIG_SYS_IMMR 0xFF000000 -#define CONFIG_SYS_IMMR_SIZE ((uint)(64 * 1024)) - -/*----------------------------------------------------------------------- - * Definitions for initial stack pointer and data area (in DPRAM) - */ -#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR -#define CONFIG_SYS_INIT_RAM_END 0x2F00 /* End of used area in DPRAM */ -#define CONFIG_SYS_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */ -#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE) -#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET - -/*----------------------------------------------------------------------- - * Start addresses for the final memory configuration - * (Set up by the startup code) - * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 - */ -#define CONFIG_SYS_SDRAM_BASE 0x00000000 - -#define CONFIG_SYS_FLASH_BASE 0x80000000 - -#define CONFIG_SYS_FLASH_SIZE ((uint)(8 * 1024 * 1024)) /* max 8Mbyte */ - -#define CONFIG_SYS_MONITOR_LEN (384 << 10) /* Reserve 384 kB for Monitor */ - -#define CONFIG_SYS_MONITOR_BASE TEXT_BASE - -#define CONFIG_SYS_MALLOC_LEN (384 << 10) /* Reserve 384 kB for malloc() */ - -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ -/*----------------------------------------------------------------------- - * FLASH organization - */ -#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ -#define CONFIG_SYS_MAX_FLASH_SECT 8 /* max number of sectors on one chip */ - -#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ -#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ - -#define CONFIG_ENV_IS_IN_FLASH 1 -#undef CONFIG_ENV_IS_IN_EEPROM -#define CONFIG_ENV_OFFSET 0x000E0000 -#define CONFIG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */ - -#define CONFIG_ENV_SECT_SIZE 0x50000 /* see README - env sector total size */ - -/*----------------------------------------------------------------------- - * Cache Configuration - */ -#define CONFIG_SYS_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */ -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_SYS_CACHELINE_SHIFT 4 /* log base 2 of the above value */ -#endif - -/*----------------------------------------------------------------------- - * SYPCR - System Protection Control 11-9 - * SYPCR can only be written once after reset! - *----------------------------------------------------------------------- - * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze - */ -#if defined(CONFIG_WATCHDOG) -#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \ - SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP) -#else -#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP) -#endif - -/*----------------------------------------------------------------------- - * SIUMCR - SIU Module Configuration 11-6 - *----------------------------------------------------------------------- - * PCMCIA config., multi-function pin tri-state - */ -#define CONFIG_SYS_SIUMCR (SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01) - -/*----------------------------------------------------------------------- - * TBSCR - Time Base Status and Control 11-26 - *----------------------------------------------------------------------- - * Clear Reference Interrupt Status, Timebase freezing enabled - */ -#define CONFIG_SYS_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF) - -/*---------------------------------------------------------------------- - * RTCSC - Real-Time Clock Status and Control Register 11-27 - *----------------------------------------------------------------------- - */ - -/*FIXME dont use for now */ -/*#define CONFIG_SYS_RTCSC (RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE) */ -/*#define CONFIG_SYS_RTCSC (RTCSC_RTF) */ - -/*----------------------------------------------------------------------- - * PISCR - Periodic Interrupt Status and Control 11-31 - *----------------------------------------------------------------------- - * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled - */ -#define CONFIG_SYS_PISCR (PISCR_PS | PISCR_PITF) -/* PITE */ -/*----------------------------------------------------------------------- - * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30 - *----------------------------------------------------------------------- - * set the PLL, the low-power modes and the reset control (15-29) - */ -#define CONFIG_SYS_PLPRCR (((MPC8XX_FACT-1) << PLPRCR_MF_SHIFT) | \ - PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST) - -/*----------------------------------------------------------------------- - * SCCR - System Clock and reset Control Register 15-27 - *----------------------------------------------------------------------- - * Set clock output, timebase and RTC source and divider, - * power management and some other internal clocks - */ - -/* FIXME check values */ -#define SCCR_MASK SCCR_EBDF11 -#define CONFIG_SYS_SCCR (SCCR_TBS|SCCR_RTSEL|SCCR_COM00|SCCR_DFSYNC00|SCCR_DFBRG00|SCCR_DFNL000|SCCR_DFNH000|SCCR_DFLCD000|SCCR_DFALCD00) - - /*----------------------------------------------------------------------- - * - *----------------------------------------------------------------------- - * - */ -#define CONFIG_SYS_DER 0 - -/* Because of the way the 860 starts up and assigns CS0 the -* entire address space, we have to set the memory controller -* differently. Normally, you write the option register -* first, and then enable the chip select by writing the -* base register. For CS0, you must write the base register -* first, followed by the option register. -*/ - -/* - * Init Memory Controller: - * - * BR0/1 and OR0/1 (FLASH) - */ -/* the other CS:s are determined by looking at parameters in BCSRx */ - -#define FLASH_BASE0_PRELIM CONFIG_SYS_FLASH_BASE /* FLASH bank #0 */ - -#define CONFIG_SYS_REMAP_OR_AM 0xFF800000 /* 4 MB OR addr mask */ -#define CONFIG_SYS_PRELIM_OR_AM 0xFF800000 /* OR addr mask */ - -#define FPGA_2_BASE 0x90000000 -#define FPGA_3_BASE 0x98000000 - -/* FLASH timing: ACS = 10, TRLX = 1, CSNT = 1, SCY = 3, EHTR = 0 */ -#define CONFIG_SYS_OR_TIMING_FLASH (OR_CSNT_SAM | OR_ACS_DIV4 | OR_BI | OR_SCY_3_CLK | OR_TRLX) - -#define CONFIG_SYS_OR0_REMAP (CONFIG_SYS_REMAP_OR_AM | CONFIG_SYS_OR_TIMING_FLASH) - - -#define CONFIG_SYS_OR0_PRELIM (CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH) /* 1 Mbyte until detected and only 1 Mbyte is needed*/ -#define CONFIG_SYS_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_V | BR_PS_16 ) - -/* - * Internal Definitions - * - * Boot Flags - */ -#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ -#define BOOTFLAG_WARM 0x02 /* Software reboot */ - -#define CONFIG_ETHADDR DE:AD:BE:EF:00:01 /* Ethernet address */ - -#ifdef CONFIG_MPC860T - -/* Interrupt level assignments. -*/ -#define FEC_INTERRUPT SIU_LEVEL1 /* FEC interrupt */ - -#endif /* CONFIG_MPC860T */ - -/* We don't use the 8259. -*/ -#define NR_8259_INTS 0 - -/* Machine type -*/ -#define _MACH_8xx (_MACH_gth) - -#ifdef CONFIG_MPC860 -#define PCMCIA_SLOT_A 1 -#define CONFIG_PCMCIA_SLOT_A 1 -#endif - -#define CONFIG_SYS_PCMCIA_MEM_ADDR (0xE0000000) -#define CONFIG_SYS_PCMCIA_MEM_SIZE ( 64 << 20 ) -#define CONFIG_SYS_PCMCIA_DMA_ADDR (0xE4000000) -#define CONFIG_SYS_PCMCIA_DMA_SIZE ( 64 << 20 ) -#define CONFIG_SYS_PCMCIA_ATTRB_ADDR (0xE8000000) -#define CONFIG_SYS_PCMCIA_ATTRB_SIZE ( 64 << 20 ) -#define CONFIG_SYS_PCMCIA_IO_ADDR (0xEC000000) -#define CONFIG_SYS_PCMCIA_IO_SIZE ( 64 << 20 ) - -#define CONFIG_IDE_8xx_PCCARD 1 /* Use IDE with PC Card Adapter */ -#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */ -#undef CONFIG_IDE_LED /* LED for ide not supported */ -#undef CONFIG_IDE_RESET /* reset for ide not supported */ - -#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */ -#define CONFIG_SYS_IDE_MAXDEVICE 1 /* max. 1 drive per IDE bus */ - -#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000 -#define CONFIG_SYS_ATA_BASE_ADDR CONFIG_SYS_PCMCIA_MEM_ADDR -/* Offset for data I/O */ -#define CONFIG_SYS_ATA_DATA_OFFSET (CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320) -/* Offset for normal register accesses */ -#define CONFIG_SYS_ATA_REG_OFFSET (2 * CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320) -/* Offset for alternate registers */ -#define CONFIG_SYS_ATA_ALT_OFFSET 0x0100 - -#define CONFIG_8xx_GCLK_FREQ MPC8XX_HZ /* Force it - dont measure it */ - -#define PA_FRONT_LED ((u16)0x4) /* PA 13 */ -#define PA_FL_CONFIG ((u16)0x20) /* PA 10 */ -#define PA_FL_CE ((u16)0x1000) /* PA 3 */ - -#define PB_ID_GND ((u32)1) /* PB 31 */ -#define PB_REV_1 ((u32)2) /* PB 30 */ -#define PB_REV_0 ((u32)4) /* PB 29 */ -#define PB_BLUE_LED ((u32)0x400) /* PB 21 */ -#define PB_EEPROM ((u32)0x800) /* PB 20 */ -#define PB_ID_3 ((u32)0x2000) /* PB 18 */ -#define PB_ID_2 ((u32)0x4000) /* PB 17 */ -#define PB_ID_1 ((u32)0x8000) /* PB 16 */ -#define PB_ID_0 ((u32)0x10000) /* PB 15 */ - -/* NOTE. This is reset for 100Mbit port only */ -#define PC_ENET100_RESET ((ushort)0x0080) /* PC 8 */ - -#endif /* __CONFIG_H */ |