diff options
Diffstat (limited to 'include/configs/taishan.h')
| -rw-r--r-- | include/configs/taishan.h | 161 |
1 files changed, 15 insertions, 146 deletions
diff --git a/include/configs/taishan.h b/include/configs/taishan.h index 1879d38..ba42192 100644 --- a/include/configs/taishan.h +++ b/include/configs/taishan.h @@ -32,9 +32,15 @@ #define CONFIG_440GX 1 /* Specifc GX support */ #define CONFIG_440 1 /* ... PPC440 family */ #define CONFIG_4xx 1 /* ... PPC4xx family */ -#undef CFG_DRAM_TEST /* Disable-takes long time! */ #define CONFIG_SYS_CLK_FREQ 33333333 /* external freq to pll */ +/* + * Include common defines/options for all AMCC eval boards + */ +#define CONFIG_HOSTNAME taishan +#define CONFIG_USE_TTY ttyS1 +#include "amcc-common.h" + #define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */ #define CONFIG_MISC_INIT_R 1 /* Call misc_init_r */ @@ -42,9 +48,7 @@ * Base addresses -- Note these are effective addresses where the * actual resources get mapped (not physical addresses) *----------------------------------------------------------------------*/ -#define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */ #define CFG_FLASH_BASE 0xfc000000 /* start of FLASH */ -#define CFG_MONITOR_BASE 0xfffc0000 /* start of monitor */ #define CFG_PCI_MEMBASE 0x80000000 /* mapped pci memory */ #define CFG_PERIPHERAL_BASE 0xe0000000 /* internal peripherals */ #define CFG_ISRAM_BASE 0xc0000000 /* internal SRAM */ @@ -70,19 +74,11 @@ #define CFG_POST_WORD_ADDR (CFG_GBL_DATA_OFFSET - 0x4) #define CFG_INIT_SP_OFFSET CFG_POST_WORD_ADDR -#define CFG_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon*/ -#define CFG_MALLOC_LEN (1024 * 1024) /* Reserve 1024 kB for malloc*/ - /*----------------------------------------------------------------------- * Serial Port *----------------------------------------------------------------------*/ #define CONFIG_UART1_CONSOLE 1 /* use of UART1 as console */ -#define CONFIG_SERIAL_MULTI 1 /* enable serial multi support */ #define CFG_EXT_SERIAL_CLOCK (1843200 * 6) /* Ext clk @ 11.059 MHz */ -#define CONFIG_BAUDRATE 115200 - -#define CFG_BAUDRATE_TABLE \ - {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} /*----------------------------------------------------------------------- * Environment @@ -138,10 +134,7 @@ /*----------------------------------------------------------------------- * I2C *----------------------------------------------------------------------*/ -#define CONFIG_HARD_I2C 1 /* I2C with hardware support */ -#undef CONFIG_SOFT_I2C /* I2C bit-banged */ #define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ -#define CFG_I2C_SLAVE 0x7F #undef CFG_I2C_MULTI_EEPROMS #define CFG_I2C_EEPROM_ADDR 0x50 @@ -159,65 +152,23 @@ #define CFG_DTT_LOW_TEMP -30 #define CFG_DTT_HYSTERESIS 3 -/*----------------------------------------------------------------------- - * Environment - *----------------------------------------------------------------------*/ - -#define CONFIG_PREBOOT "echo;" \ - "echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \ - "echo" - -#undef CONFIG_BOOTARGS - +/* + * Default environment variables + */ #define CONFIG_EXTRA_ENV_SETTINGS \ - "netdev=eth0\0" \ - "hostname=taishan\0" \ - "nfsargs=setenv bootargs root=/dev/nfs rw " \ - "nfsroot=${serverip}:${rootpath}\0" \ - "ramargs=setenv bootargs root=/dev/ram rw\0" \ - "addip=setenv bootargs ${bootargs} " \ - "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ - ":${hostname}:${netdev}:off panic=1\0" \ - "addtty=setenv bootargs ${bootargs} console=ttyS1,${baudrate}\0"\ - "flash_nfs=run nfsargs addip addtty;" \ - "bootm ${kernel_addr}\0" \ - "flash_self=run ramargs addip addtty;" \ - "bootm ${kernel_addr} ${ramdisk_addr}\0" \ - "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \ - "bootm\0" \ - "rootpath=/opt/eldk/ppc_4xx\0" \ - "bootfile=/tftpboot/taishan/uImage\0" \ + CONFIG_AMCC_DEF_ENV \ + CONFIG_AMCC_DEF_ENV_POWERPC \ + CONFIG_AMCC_DEF_ENV_PPC_OLD \ + CONFIG_AMCC_DEF_ENV_NOR_UPD \ "kernel_addr=fc000000\0" \ "ramdisk_addr=fc180000\0" \ - "initrd_high=30000000\0" \ - "load=tftp 100000 /tftpboot/taishan/u-boot.bin\0" \ - "update=protect off fffc0000 ffffffff;era fffc0000 ffffffff;" \ - "cp.b 100000 fffc0000 40000;" \ - "setenv filesize;saveenv\0" \ - "upd=run load update\0" \ - "fixedip=setenv bootargs $(bootargs) ip=$(ipaddr):$(serverip):" \ - "$(gatewayip):$(netmask):$(hostname):$(netdev):off panic=1\0" \ - "dhcp=setenv bootargs $(bootargs) ip=dhcp\0" \ "kozio=bootm 0xffe00000\0" \ "" -#define CONFIG_BOOTCOMMAND "run flash_self" - -#if 0 -#define CONFIG_BOOTDELAY -1 /* autoboot disabled */ -#else -#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ -#endif - -#define CONFIG_BAUDRATE 115200 -#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */ -#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */ /*----------------------------------------------------------------------- * Networking *----------------------------------------------------------------------*/ #define CONFIG_EMAC_NR_START 2 /* start with EMAC 2 (skip 0&1) */ -#define CONFIG_MII 1 /* MII PHY management */ -#define CONFIG_NET_MULTI 1 #define CONFIG_PHY_ADDR 0xff /* no phy on EMAC0 */ #define CONFIG_PHY1_ADDR 0xff /* no phy on EMAC1 */ #define CONFIG_PHY2_ADDR 0x1 @@ -230,70 +181,12 @@ #define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */ #define CONFIG_PHY_RESET 1 /* reset phy upon startup */ #define CONFIG_PHY_RESET_DELAY 1000 -#define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */ - -#define CONFIG_NETCONSOLE /* include NetConsole support */ - - -/* - * BOOTP options - */ -#define CONFIG_BOOTP_BOOTFILESIZE -#define CONFIG_BOOTP_BOOTPATH -#define CONFIG_BOOTP_GATEWAY -#define CONFIG_BOOTP_HOSTNAME - /* - * Command line configuration. + * Commands additional to the ones defined in amcc-common.h */ -#include <config_cmd_default.h> - -#define CONFIG_CMD_ASKENV -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_DIAG #define CONFIG_CMD_DTT -#define CONFIG_CMD_ELF -#define CONFIG_CMD_EEPROM -#define CONFIG_CMD_I2C -#define CONFIG_CMD_IRQ -#define CONFIG_CMD_MII -#define CONFIG_CMD_NET -#define CONFIG_CMD_NFS #define CONFIG_CMD_PCI -#define CONFIG_CMD_PING -#define CONFIG_CMD_REGINFO - - -#undef CONFIG_WATCHDOG /* watchdog disabled */ - -/*----------------------------------------------------------------------- - * Miscellaneous configurable options - *----------------------------------------------------------------------*/ -#define CFG_LONGHELP /* undef to save memory */ -#define CFG_PROMPT "=> " /* Monitor Command Prompt */ -#if defined(CONFIG_CMD_KGDB) -#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */ -#else -#define CFG_CBSIZE 256 /* Console I/O Buffer Size */ -#endif -#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */ -#define CFG_MAXARGS 16 /* max number of command args */ -#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */ - -#define CFG_MEMTEST_START 0x0400000 /* memtest works on */ -#define CFG_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ - -#define CFG_LOAD_ADDR 0x100000 /* default load address */ -#define CFG_EXTBDINFO 1 /* To use extended board_into (bd_t) */ - -#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */ - -#define CONFIG_CMDLINE_EDITING 1 /* add command line history */ -#define CONFIG_LOOPW 1 /* enable loopw command */ -#define CONFIG_MX_CYCLIC 1 /* enable mdc/mwc commands */ -#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ -#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */ /*----------------------------------------------------------------------- * PCI stuff @@ -312,28 +205,4 @@ #define CFG_PCI_SUBSYS_VENDORID 0x10e8 /* AMCC */ #define CFG_PCI_SUBSYS_DEVICEID 0xcafe /* Whatever */ -/* - * For booting Linux, the board info and command line data - * have to be in the first 8 MB of memory, since this is - * the maximum mapped by the Linux kernel during initialization. - */ -#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ - -/* - * Internal Definitions - * - * Boot Flags - */ -#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */ -#define BOOTFLAG_WARM 0x02 /* Software reboot */ - -#if defined(CONFIG_CMD_KGDB) -#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ -#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ -#endif - -/* pass open firmware flat tree */ -#define CONFIG_OF_LIBFDT 1 -#define CONFIG_OF_BOARD_SETUP 1 - #endif /* __CONFIG_H */ |