diff options
Diffstat (limited to 'include/configs/lwmon5.h')
| -rw-r--r-- | include/configs/lwmon5.h | 106 |
1 files changed, 78 insertions, 28 deletions
diff --git a/include/configs/lwmon5.h b/include/configs/lwmon5.h index ef9ab22..00c34d5 100644 --- a/include/configs/lwmon5.h +++ b/include/configs/lwmon5.h @@ -34,8 +34,8 @@ #define CONFIG_SYS_CLK_FREQ 33300000 /* external freq to pll */ #define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */ +#define CONFIG_BOARD_POSTCLK_INIT 1 /* Call board_postclk_init */ #define CONFIG_MISC_INIT_R 1 /* Call misc_init_r */ -#define CONFIG_ADD_RAM_INFO 1 /* Print additional info */ /*----------------------------------------------------------------------- * Base addresses -- Note these are effective addresses where the @@ -46,7 +46,7 @@ #define CFG_BOOT_BASE_ADDR 0xf0000000 #define CFG_SDRAM_BASE 0x00000000 /* _must_ be 0 */ -#define CFG_FLASH_BASE 0xfc000000 /* start of FLASH */ +#define CFG_FLASH_BASE 0xf8000000 /* start of FLASH */ #define CFG_MONITOR_BASE TEXT_BASE #define CFG_LIME_BASE_0 0xc0000000 #define CFG_LIME_BASE_1 0xc1000000 @@ -72,13 +72,14 @@ * Initial RAM & stack pointer *----------------------------------------------------------------------*/ /* 440EPx/440GRx have 16KB of internal SRAM, so no need for D-Cache */ -#define CFG_INIT_RAM_OCM 1 /* OCM as init ram */ #define CFG_INIT_RAM_ADDR CFG_OCM_BASE /* OCM */ +#define CFG_OCM_DATA_ADDR CFG_OCM_BASE #define CFG_INIT_RAM_END (4 << 10) #define CFG_GBL_DATA_SIZE 256 /* num bytes initial data */ #define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) -#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET +#define CFG_POST_WORD_ADDR (CFG_GBL_DATA_OFFSET - 0x4) +#define CFG_INIT_SP_OFFSET CFG_POST_WORD_ADDR /*----------------------------------------------------------------------- * Serial Port @@ -103,9 +104,11 @@ #define CFG_FLASH_CFI /* The flash is CFI compatible */ #define CFG_FLASH_CFI_DRIVER /* Use common CFI driver */ -#define CFG_FLASH_BANKS_LIST { CFG_FLASH_BASE } +#define CFG_FLASH0 0xFC000000 +#define CFG_FLASH1 0xF8000000 +#define CFG_FLASH_BANKS_LIST { CFG_FLASH1, CFG_FLASH0 } -#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */ +#define CFG_MAX_FLASH_BANKS 2 /* max number of memory banks */ #define CFG_MAX_FLASH_SECT 512 /* max number of sectors on one chip */ #define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ @@ -133,35 +136,63 @@ #define CONFIG_DDR_DATA_EYE 1 /* use DDR2 optimization */ #if 0 /* test-only: disable ECC for now */ #define CONFIG_DDR_ECC 1 /* enable ECC */ +#define CFG_POST_ECC_ON CFG_POST_ECC +#else +#define CFG_POST_ECC_ON 0 #endif +/* POST support */ +#define CONFIG_POST (CFG_POST_CACHE | \ + CFG_POST_CPU | \ + CFG_POST_ECC_ON | \ + CFG_POST_ETHER | \ + CFG_POST_FPU | \ + CFG_POST_I2C | \ + CFG_POST_MEMORY | \ + CFG_POST_RTC | \ + CFG_POST_SPR | \ + CFG_POST_UART) + +#define CFG_POST_CACHE_ADDR 0x10000000 /* free virtual address */ +#define CONFIG_LOGBUFFER +#define CFG_CONSOLE_IS_IN_ENV /* Otherwise it catches logbuffer as output */ + /*----------------------------------------------------------------------- * I2C *----------------------------------------------------------------------*/ #define CONFIG_HARD_I2C 1 /* I2C with hardware support */ #undef CONFIG_SOFT_I2C /* I2C bit-banged */ -#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */ +#define CFG_I2C_SPEED 100000 /* I2C speed and slave address */ #define CFG_I2C_SLAVE 0x7F -#define CFG_I2C_MULTI_EEPROMS -#define CFG_I2C_EEPROM_ADDR (0xa8>>1) -#define CFG_I2C_EEPROM_ADDR_LEN 1 +#define CFG_I2C_EEPROM_ADDR 0x53 /* EEPROM AT24C128 */ +#define CFG_I2C_EEPROM_ADDR_LEN 2 /* Bytes of address */ +#define CFG_EEPROM_PAGE_WRITE_BITS 6 /* The Atmel AT24C128 has */ + /* 64 byte page write mode using*/ + /* last 6 bits of the address */ +#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */ #define CFG_EEPROM_PAGE_WRITE_ENABLE -#define CFG_EEPROM_PAGE_WRITE_BITS 3 -#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10 #define CONFIG_RTC_PCF8563 1 /* enable Philips PCF8563 RTC */ #define CFG_I2C_RTC_ADDR 0x51 /* Philips PCF8563 RTC address */ +#define CFG_I2C_KEYBD_ADDR 0x56 /* PIC LWE keyboard */ + +#define CONFIG_POST_KEY_MAGIC "3C+3E" /* press F3 + F5 keys to force POST */ +#if 0 +#define CONFIG_AUTOBOOT_KEYED /* Enable "password" protection */ +#define CONFIG_AUTOBOOT_PROMPT "\nEnter password - autoboot in %d sec...\n" +#define CONFIG_AUTOBOOT_DELAY_STR " " /* "password" */ +#endif -#define CONFIG_PREBOOT "echo;" \ - "echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \ - "echo" +#define CONFIG_PREBOOT "setenv bootdelay 15" #undef CONFIG_BOOTARGS #define CONFIG_EXTRA_ENV_SETTINGS \ "hostname=lwmon5\0" \ "netdev=eth0\0" \ + "unlock=yes\0" \ + "logversion=2\0" \ "nfsargs=setenv bootargs root=/dev/nfs rw " \ "nfsroot=${serverip}:${rootpath}\0" \ "ramargs=setenv bootargs root=/dev/ram rw\0" \ @@ -169,12 +200,13 @@ "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ ":${hostname}:${netdev}:off panic=1\0" \ "addtty=setenv bootargs ${bootargs} console=ttyS1,${baudrate}\0"\ - "flash_nfs=run nfsargs addip addtty;" \ + "addmisc=setenv bootargs ${bootargs} rtc-pcf8563.probe=0,0x51\0"\ + "flash_nfs=run nfsargs addip addtty addmisc;" \ "bootm ${kernel_addr}\0" \ - "flash_self=run ramargs addip addtty;" \ + "flash_self=run ramargs addip addtty addmisc;" \ "bootm ${kernel_addr} ${ramdisk_addr}\0" \ - "net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \ - "bootm\0" \ + "net_nfs=tftp 200000 ${bootfile};" \ + "run nfsargs addip addtty addmisc;bootm\0" \ "rootpath=/opt/eldk/ppc_4xxFP\0" \ "bootfile=/tftpboot/lwmon5/uImage\0" \ "kernel_addr=FC000000\0" \ @@ -183,6 +215,8 @@ "update=protect off FFF80000 FFFFFFFF;era FFF80000 FFFFFFFF;" \ "cp.b 200000 FFF80000 80000\0" \ "upd=run load;run update\0" \ + "lwe_env=tftp 200000 /tftpboot.dev/lwmon5/env_uboot.bin;" \ + "autoscr 200000\0" \ "" #define CONFIG_BOOTCOMMAND "run flash_self" @@ -200,6 +234,7 @@ #define CONFIG_PHY_ADDR 3 /* PHY address, See schematics */ #define CONFIG_PHY_RESET 1 /* reset phy upon startup */ +#define CONFIG_PHY_RESET_DELAY 300 #define CONFIG_HAS_ETH0 #define CFG_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */ @@ -223,7 +258,6 @@ #define CONFIG_DOS_PARTITION #define CONFIG_ISO_PARTITION - /* * BOOTP options */ @@ -232,7 +266,6 @@ #define CONFIG_BOOTP_GATEWAY #define CONFIG_BOOTP_HOSTNAME - /* * Command line configuration. */ @@ -247,6 +280,7 @@ #define CONFIG_CMD_FAT #define CONFIG_CMD_I2C #define CONFIG_CMD_IRQ +#define CONFIG_CMD_LOG #define CONFIG_CMD_MII #define CONFIG_CMD_NET #define CONFIG_CMD_NFS @@ -259,7 +293,6 @@ #define CONFIG_CMD_USB #endif - /*----------------------------------------------------------------------- * Miscellaneous configurable options *----------------------------------------------------------------------*/ @@ -306,7 +339,12 @@ #define CFG_PCI_SUBSYS_VENDORID 0x10e8 /* AMCC */ #define CFG_PCI_SUBSYS_ID 0xcafe /* Whatever */ +#if 0 +/* + * ToDo: Watchdog is not test fully, so exclude it for now + */ #define CONFIG_HW_WATCHDOG 1 /* Use external HW-Watchdog */ +#endif /* * For booting Linux, the board info and command line data @@ -322,7 +360,7 @@ /* Memory Bank 0 (NOR-FLASH) initialization */ #define CFG_EBC_PB0AP 0x03050200 -#define CFG_EBC_PB0CR (CFG_FLASH | 0xdc000) +#define CFG_EBC_PB0CR (CFG_FLASH | 0xfc000) /* Memory Bank 1 (Lime) initialization */ #define CFG_EBC_PB1AP 0x01004380 @@ -342,14 +380,24 @@ * Graphics (Fujitsu Lime) *----------------------------------------------------------------------*/ /* SDRAM Clock frequency adjustment register */ -#define CFG_LIME_SDRAM_CLOCK 0xC1FC0000 -/* Lime Clock frequency is to set 133MHz */ +#define CFG_LIME_SDRAM_CLOCK 0xC1FC0038 +/* Lime Clock frequency is to set 100MHz */ +#define CFG_LIME_CLOCK_100MHZ 0x00000 +#if 0 +/* Lime Clock frequency for 133MHz */ #define CFG_LIME_CLOCK_133MHZ 0x10000 +#endif /* SDRAM Parameter register */ #define CFG_LIME_MMR 0xC1FCFFFC -/* SDRAM parameter value */ +/* SDRAM parameter value; was 0x414FB7F2, caused several vertical bars + and pixel flare on display when 133MHz was configured. According to + SDRAM chip datasheet CAS Latency is 3 for 133MHz and -75 Speed Grade */ +#ifdef CFG_LIME_CLOCK_133MHZ +#define CFG_LIME_MMR_VALUE 0x414FB7F3 +#else #define CFG_LIME_MMR_VALUE 0x414FB7F2 +#endif /*----------------------------------------------------------------------- * GPIO Setup @@ -357,9 +405,11 @@ #define CFG_GPIO_PHY1_RST 12 #define CFG_GPIO_FLASH_WP 14 #define CFG_GPIO_PHY0_RST 22 -#define CFG_GPIO_WATCHDOG 58 +#define CFG_GPIO_EEPROM_EXT_WP 55 +#define CFG_GPIO_EEPROM_INT_WP 57 #define CFG_GPIO_LIME_S 59 #define CFG_GPIO_LIME_RST 60 +#define CFG_GPIO_WATCHDOG 63 /*----------------------------------------------------------------------- * PPC440 GPIO Configuration @@ -428,7 +478,7 @@ {GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_1}, /* GPIO55 Unselect via TraceSelect Bit */ \ {GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_0}, /* GPIO56 Unselect via TraceSelect Bit */ \ {GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_1}, /* GPIO57 Unselect via TraceSelect Bit */ \ -{GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_1}, /* GPIO58 Unselect via TraceSelect Bit */ \ +{GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_0}, /* GPIO58 Unselect via TraceSelect Bit */ \ {GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_0}, /* GPIO59 Unselect via TraceSelect Bit */ \ {GPIO1_BASE, GPIO_OUT, GPIO_SEL , GPIO_OUT_0}, /* GPIO60 Unselect via TraceSelect Bit */ \ {GPIO1_BASE, GPIO_IN , GPIO_SEL , GPIO_OUT_0}, /* GPIO61 Unselect via TraceSelect Bit */ \ |