diff options
Diffstat (limited to 'drivers')
-rw-r--r-- | drivers/spi/mxc_spi.c | 9 | ||||
-rw-r--r-- | drivers/usb/host/ehci-mx5.c | 146 | ||||
-rw-r--r-- | drivers/usb/host/ehci-mx6.c | 5 | ||||
-rw-r--r-- | drivers/usb/host/ehci-mxc.c | 225 |
4 files changed, 302 insertions, 83 deletions
diff --git a/drivers/spi/mxc_spi.c b/drivers/spi/mxc_spi.c index 13bebe8..859c43f 100644 --- a/drivers/spi/mxc_spi.c +++ b/drivers/spi/mxc_spi.c @@ -140,8 +140,8 @@ static s32 spi_cfg_mxc(struct mxc_spi_slave *mxcs, unsigned int cs, reg_ctrl = reg_read(®s->ctrl); /* Reset spi */ - reg_write(®s->ctrl, 0); - reg_write(®s->ctrl, (reg_ctrl | 0x1)); + reg_write(®s->ctrl, (reg_ctrl & ~MXC_CSPICTRL_EN)); + reg_write(®s->ctrl, (reg_ctrl | MXC_CSPICTRL_EN)); /* * The following computation is taken directly from Freescale's code. @@ -387,7 +387,7 @@ static int decode_cs(struct mxc_spi_slave *mxcs, unsigned int cs) if (cs > 3) { mxcs->gpio = cs >> 8; cs &= 3; - ret = gpio_direction_output(mxcs->gpio, 0); + ret = gpio_direction_output(mxcs->gpio, !(mxcs->ss_pol)); if (ret) { printf("mxc_spi: cannot setup gpio %d\n", mxcs->gpio); return -EINVAL; @@ -414,6 +414,8 @@ struct spi_slave *spi_setup_slave(unsigned int bus, unsigned int cs, return NULL; } + mxcs->ss_pol = (mode & SPI_CS_HIGH) ? 1 : 0; + ret = decode_cs(mxcs, cs); if (ret < 0) { free(mxcs); @@ -425,7 +427,6 @@ struct spi_slave *spi_setup_slave(unsigned int bus, unsigned int cs, mxcs->slave.bus = bus; mxcs->slave.cs = cs; mxcs->base = spi_bases[bus]; - mxcs->ss_pol = (mode & SPI_CS_HIGH) ? 1 : 0; ret = spi_cfg_mxc(mxcs, cs, max_hz, mode); if (ret) { diff --git a/drivers/usb/host/ehci-mx5.c b/drivers/usb/host/ehci-mx5.c index 9a2c295..adbed5c 100644 --- a/drivers/usb/host/ehci-mx5.c +++ b/drivers/usb/host/ehci-mx5.c @@ -29,34 +29,63 @@ #define MX5_USBOTHER_REGS_OFFSET 0x800 -#define MXC_OTG_OFFSET 0 -#define MXC_H1_OFFSET 0x200 -#define MXC_H2_OFFSET 0x400 +#define MXC_OTG_OFFSET 0 +#define MXC_H1_OFFSET 0x200 +#define MXC_H2_OFFSET 0x400 +#define MXC_H3_OFFSET 0x600 #define MXC_USBCTRL_OFFSET 0 #define MXC_USB_PHY_CTR_FUNC_OFFSET 0x8 #define MXC_USB_PHY_CTR_FUNC2_OFFSET 0xc #define MXC_USB_CTRL_1_OFFSET 0x10 #define MXC_USBH2CTRL_OFFSET 0x14 +#define MXC_USBH3CTRL_OFFSET 0x18 /* USB_CTRL */ -#define MXC_OTG_UCTRL_OWIE_BIT (1 << 27) /* OTG wakeup intr enable */ -#define MXC_OTG_UCTRL_OPM_BIT (1 << 24) /* OTG power mask */ -#define MXC_H1_UCTRL_H1UIE_BIT (1 << 12) /* Host1 ULPI interrupt enable */ -#define MXC_H1_UCTRL_H1WIE_BIT (1 << 11) /* HOST1 wakeup intr enable */ -#define MXC_H1_UCTRL_H1PM_BIT (1 << 8) /* HOST1 power mask */ +/* OTG wakeup intr enable */ +#define MXC_OTG_UCTRL_OWIE_BIT (1 << 27) +/* OTG power mask */ +#define MXC_OTG_UCTRL_OPM_BIT (1 << 24) +/* OTG power pin polarity */ +#define MXC_OTG_UCTRL_O_PWR_POL_BIT (1 << 24) +/* Host1 ULPI interrupt enable */ +#define MXC_H1_UCTRL_H1UIE_BIT (1 << 12) +/* HOST1 wakeup intr enable */ +#define MXC_H1_UCTRL_H1WIE_BIT (1 << 11) +/* HOST1 power mask */ +#define MXC_H1_UCTRL_H1PM_BIT (1 << 8) +/* HOST1 power pin polarity */ +#define MXC_H1_UCTRL_H1_PWR_POL_BIT (1 << 8) /* USB_PHY_CTRL_FUNC */ -#define MXC_OTG_PHYCTRL_OC_DIS_BIT (1 << 8) /* OTG Disable Overcurrent Event */ -#define MXC_H1_OC_DIS_BIT (1 << 5) /* UH1 Disable Overcurrent Event */ +/* OTG Polarity of Overcurrent */ +#define MXC_OTG_PHYCTRL_OC_POL_BIT (1 << 9) +/* OTG Disable Overcurrent Event */ +#define MXC_OTG_PHYCTRL_OC_DIS_BIT (1 << 8) +/* UH1 Polarity of Overcurrent */ +#define MXC_H1_OC_POL_BIT (1 << 6) +/* UH1 Disable Overcurrent Event */ +#define MXC_H1_OC_DIS_BIT (1 << 5) +/* OTG Power Pin Polarity */ +#define MXC_OTG_PHYCTRL_PWR_POL_BIT (1 << 3) /* USBH2CTRL */ -#define MXC_H2_UCTRL_H2UIE_BIT (1 << 8) -#define MXC_H2_UCTRL_H2WIE_BIT (1 << 7) -#define MXC_H2_UCTRL_H2PM_BIT (1 << 4) +#define MXC_H2_UCTRL_H2_OC_POL_BIT (1 << 31) +#define MXC_H2_UCTRL_H2_OC_DIS_BIT (1 << 30) +#define MXC_H2_UCTRL_H2UIE_BIT (1 << 8) +#define MXC_H2_UCTRL_H2WIE_BIT (1 << 7) +#define MXC_H2_UCTRL_H2PM_BIT (1 << 4) +#define MXC_H2_UCTRL_H2_PWR_POL_BIT (1 << 4) + +/* USBH3CTRL */ +#define MXC_H3_UCTRL_H3_OC_POL_BIT (1 << 31) +#define MXC_H3_UCTRL_H3_OC_DIS_BIT (1 << 30) +#define MXC_H3_UCTRL_H3UIE_BIT (1 << 8) +#define MXC_H3_UCTRL_H3WIE_BIT (1 << 7) +#define MXC_H3_UCTRL_H3_PWR_POL_BIT (1 << 4) /* USB_CTRL_1 */ -#define MXC_USB_CTRL_UH1_EXT_CLK_EN (1 << 25) +#define MXC_USB_CTRL_UH1_EXT_CLK_EN (1 << 25) /* USB pin configuration */ #define USB_PAD_CONFIG (PAD_CTL_PKE_ENABLE | PAD_CTL_SRE_FAST | \ @@ -143,24 +172,42 @@ int mxc_set_usbcontrol(int port, unsigned int flags) if (flags & MXC_EHCI_INTERNAL_PHY) { v = __raw_readl(usbother_base + MXC_USB_PHY_CTR_FUNC_OFFSET); + if (flags & MXC_EHCI_OC_PIN_ACTIVE_LOW) + v |= MXC_OTG_PHYCTRL_OC_POL_BIT; + else + v &= ~MXC_OTG_PHYCTRL_OC_POL_BIT; if (flags & MXC_EHCI_POWER_PINS_ENABLED) + /* OC/USBPWR is used */ + v &= ~MXC_OTG_PHYCTRL_OC_DIS_BIT; + else /* OC/USBPWR is not used */ v |= MXC_OTG_PHYCTRL_OC_DIS_BIT; +#ifdef CONFIG_MX51 + if (flags & MXC_EHCI_PWR_PIN_ACTIVE_HIGH) + v |= MXC_OTG_PHYCTRL_PWR_POL_BIT; else - /* OC/USBPWR is used */ - v &= ~MXC_OTG_PHYCTRL_OC_DIS_BIT; + v &= ~MXC_OTG_PHYCTRL_PWR_POL_BIT; +#endif __raw_writel(v, usbother_base + MXC_USB_PHY_CTR_FUNC_OFFSET); v = __raw_readl(usbother_base + MXC_USBCTRL_OFFSET); +#ifdef CONFIG_MX51 if (flags & MXC_EHCI_POWER_PINS_ENABLED) + v &= ~MXC_OTG_UCTRL_OPM_BIT; + else v |= MXC_OTG_UCTRL_OPM_BIT; +#endif +#ifdef CONFIG_MX53 + if (flags & MXC_EHCI_PWR_PIN_ACTIVE_HIGH) + v |= MXC_OTG_UCTRL_O_PWR_POL_BIT; else - v &= ~MXC_OTG_UCTRL_OPM_BIT; + v &= ~MXC_OTG_UCTRL_O_PWR_POL_BIT; +#endif __raw_writel(v, usbother_base + MXC_USBCTRL_OFFSET); } break; - case 1: /* Host 1 Host ULPI */ + case 1: /* Host 1 ULPI */ #ifdef CONFIG_MX51 /* The clock for the USBH1 ULPI port will come externally from the PHY. */ @@ -170,13 +217,25 @@ int mxc_set_usbcontrol(int port, unsigned int flags) #endif v = __raw_readl(usbother_base + MXC_USBCTRL_OFFSET); +#ifdef CONFIG_MX51 if (flags & MXC_EHCI_POWER_PINS_ENABLED) - v &= ~MXC_H1_UCTRL_H1PM_BIT; /* HOST1 power mask used */ + v &= ~MXC_H1_UCTRL_H1PM_BIT; /* H1 power mask unused */ else - v |= MXC_H1_UCTRL_H1PM_BIT; /* HOST1 power mask used */ + v |= MXC_H1_UCTRL_H1PM_BIT; /* H1 power mask used */ +#endif +#ifdef CONFIG_MX53 + if (flags & MXC_EHCI_PWR_PIN_ACTIVE_HIGH) + v |= MXC_H1_UCTRL_H1_PWR_POL_BIT; + else + v &= ~MXC_H1_UCTRL_H1_PWR_POL_BIT; +#endif __raw_writel(v, usbother_base + MXC_USBCTRL_OFFSET); v = __raw_readl(usbother_base + MXC_USB_PHY_CTR_FUNC_OFFSET); + if (flags & MXC_EHCI_OC_PIN_ACTIVE_LOW) + v |= MXC_H1_OC_POL_BIT; + else + v &= ~MXC_H1_OC_POL_BIT; if (flags & MXC_EHCI_POWER_PINS_ENABLED) v &= ~MXC_H1_OC_DIS_BIT; /* OC is used */ else @@ -186,24 +245,59 @@ int mxc_set_usbcontrol(int port, unsigned int flags) break; case 2: /* Host 2 ULPI */ v = __raw_readl(usbother_base + MXC_USBH2CTRL_OFFSET); +#ifdef CONFIG_MX51 if (flags & MXC_EHCI_POWER_PINS_ENABLED) - v &= ~MXC_H2_UCTRL_H2PM_BIT; /* HOST2 power mask used */ + v &= ~MXC_H2_UCTRL_H2PM_BIT; /* H2 power mask unused */ else - v |= MXC_H2_UCTRL_H2PM_BIT; /* HOST2 power mask used */ - + v |= MXC_H2_UCTRL_H2PM_BIT; /* H2 power mask used */ +#endif +#ifdef CONFIG_MX53 + if (flags & MXC_EHCI_OC_PIN_ACTIVE_LOW) + v |= MXC_H2_UCTRL_H2_OC_POL_BIT; + else + v &= ~MXC_H2_UCTRL_H2_OC_POL_BIT; + if (flags & MXC_EHCI_POWER_PINS_ENABLED) + v &= ~MXC_H2_UCTRL_H2_OC_DIS_BIT; /* OC is used */ + else + v |= MXC_H2_UCTRL_H2_OC_DIS_BIT; /* OC is not used */ + if (flags & MXC_EHCI_PWR_PIN_ACTIVE_HIGH) + v |= MXC_H2_UCTRL_H2_PWR_POL_BIT; + else + v &= ~MXC_H2_UCTRL_H2_PWR_POL_BIT; +#endif __raw_writel(v, usbother_base + MXC_USBH2CTRL_OFFSET); break; +#ifdef CONFIG_MX53 + case 3: /* Host 3 ULPI */ + v = __raw_readl(usbother_base + MXC_USBH3CTRL_OFFSET); + if (flags & MXC_EHCI_OC_PIN_ACTIVE_LOW) + v |= MXC_H3_UCTRL_H3_OC_POL_BIT; + else + v &= ~MXC_H3_UCTRL_H3_OC_POL_BIT; + if (flags & MXC_EHCI_POWER_PINS_ENABLED) + v &= ~MXC_H3_UCTRL_H3_OC_DIS_BIT; /* OC is used */ + else + v |= MXC_H3_UCTRL_H3_OC_DIS_BIT; /* OC is not used */ + if (flags & MXC_EHCI_PWR_PIN_ACTIVE_HIGH) + v |= MXC_H3_UCTRL_H3_PWR_POL_BIT; + else + v &= ~MXC_H3_UCTRL_H3_PWR_POL_BIT; + __raw_writel(v, usbother_base + MXC_USBH3CTRL_OFFSET); + break; +#endif } return ret; } -void __board_ehci_hcd_postinit(struct usb_ehci *ehci, int port) +int __weak board_ehci_hcd_init(int port) { + return 0; } -void board_ehci_hcd_postinit(struct usb_ehci *ehci, int port) - __attribute((weak, alias("__board_ehci_hcd_postinit"))); +void __weak board_ehci_hcd_postinit(struct usb_ehci *ehci, int port) +{ +} int ehci_hcd_init(int index, struct ehci_hccr **hccr, struct ehci_hcor **hcor) { diff --git a/drivers/usb/host/ehci-mx6.c b/drivers/usb/host/ehci-mx6.c index 9ce25da..1b20e41 100644 --- a/drivers/usb/host/ehci-mx6.c +++ b/drivers/usb/host/ehci-mx6.c @@ -159,6 +159,11 @@ static void usbh1_oc_config(void) __raw_writel(val, usbother_base + USB_H1_CTRL_OFFSET); } +int __weak board_ehci_hcd_init(int port) +{ + return 0; +} + int ehci_hcd_init(int index, struct ehci_hccr **hccr, struct ehci_hcor **hcor) { struct usb_ehci *ehci; diff --git a/drivers/usb/host/ehci-mxc.c b/drivers/usb/host/ehci-mxc.c index a38bc9c..8633cab 100644 --- a/drivers/usb/host/ehci-mxc.c +++ b/drivers/usb/host/ehci-mxc.c @@ -28,14 +28,22 @@ #define USBCTRL_OTGBASE_OFFSET 0x600 -#ifdef CONFIG_MX25 -#define MX25_USB_CTRL_IP_PUE_DOWN_BIT (1<<6) -#define MX25_USB_CTRL_HSTD_BIT (1<<5) -#define MX25_USB_CTRL_USBTE_BIT (1<<4) -#define MX25_USB_CTRL_OCPOL_OTG_BIT (1<<3) -#endif +#define MX25_OTG_SIC_SHIFT 29 +#define MX25_OTG_SIC_MASK (0x3 << MX25_OTG_SIC_SHIFT) +#define MX25_OTG_PM_BIT (1 << 24) +#define MX25_OTG_PP_BIT (1 << 11) +#define MX25_OTG_OCPOL_BIT (1 << 3) + +#define MX25_H1_SIC_SHIFT 21 +#define MX25_H1_SIC_MASK (0x3 << MX25_H1_SIC_SHIFT) +#define MX25_H1_PP_BIT (1 << 18) +#define MX25_H1_PM_BIT (1 << 16) +#define MX25_H1_IPPUE_UP_BIT (1 << 7) +#define MX25_H1_IPPUE_DOWN_BIT (1 << 6) +#define MX25_H1_TLL_BIT (1 << 5) +#define MX25_H1_USBTE_BIT (1 << 4) +#define MX25_H1_OCPOL_BIT (1 << 2) -#ifdef CONFIG_MX31 #define MX31_OTG_SIC_SHIFT 29 #define MX31_OTG_SIC_MASK (0x3 << MX31_OTG_SIC_SHIFT) #define MX31_OTG_PM_BIT (1 << 24) @@ -49,59 +57,166 @@ #define MX31_H1_SIC_MASK (0x3 << MX31_H1_SIC_SHIFT) #define MX31_H1_PM_BIT (1 << 8) #define MX31_H1_DT_BIT (1 << 4) -#endif + +#define MX35_OTG_SIC_SHIFT 29 +#define MX35_OTG_SIC_MASK (0x3 << MX35_OTG_SIC_SHIFT) +#define MX35_OTG_PM_BIT (1 << 24) +#define MX35_OTG_PP_BIT (1 << 11) +#define MX35_OTG_OCPOL_BIT (1 << 3) + +#define MX35_H1_SIC_SHIFT 21 +#define MX35_H1_SIC_MASK (0x3 << MX35_H1_SIC_SHIFT) +#define MX35_H1_PP_BIT (1 << 18) +#define MX35_H1_PM_BIT (1 << 16) +#define MX35_H1_IPPUE_UP_BIT (1 << 7) +#define MX35_H1_IPPUE_DOWN_BIT (1 << 6) +#define MX35_H1_TLL_BIT (1 << 5) +#define MX35_H1_USBTE_BIT (1 << 4) +#define MX35_H1_OCPOL_BIT (1 << 2) static int mxc_set_usbcontrol(int port, unsigned int flags) { unsigned int v; -#ifdef CONFIG_MX25 - v = MX25_USB_CTRL_IP_PUE_DOWN_BIT | MX25_USB_CTRL_HSTD_BIT | - MX25_USB_CTRL_USBTE_BIT | MX25_USB_CTRL_OCPOL_OTG_BIT; -#endif + v = readl(IMX_USB_BASE + USBCTRL_OTGBASE_OFFSET); +#if defined(CONFIG_MX25) + switch (port) { + case 0: /* OTG port */ + v &= ~(MX25_OTG_SIC_MASK | MX25_OTG_PM_BIT | MX25_OTG_PP_BIT | + MX25_OTG_OCPOL_BIT); + v |= (flags & MXC_EHCI_INTERFACE_MASK) << MX25_OTG_SIC_SHIFT; -#ifdef CONFIG_MX31 - v = readl(IMX_USB_BASE + USBCTRL_OTGBASE_OFFSET); - - switch (port) { - case 0: /* OTG port */ - v &= ~(MX31_OTG_SIC_MASK | MX31_OTG_PM_BIT); - v |= (flags & MXC_EHCI_INTERFACE_MASK) - << MX31_OTG_SIC_SHIFT; - if (!(flags & MXC_EHCI_POWER_PINS_ENABLED)) - v |= MX31_OTG_PM_BIT; - - break; - case 1: /* H1 port */ - v &= ~(MX31_H1_SIC_MASK | MX31_H1_PM_BIT | - MX31_H1_DT_BIT); - v |= (flags & MXC_EHCI_INTERFACE_MASK) - << MX31_H1_SIC_SHIFT; - if (!(flags & MXC_EHCI_POWER_PINS_ENABLED)) - v |= MX31_H1_PM_BIT; - - if (!(flags & MXC_EHCI_TTL_ENABLED)) - v |= MX31_H1_DT_BIT; - - break; - case 2: /* H2 port */ - v &= ~(MX31_H2_SIC_MASK | MX31_H2_PM_BIT | - MX31_H2_DT_BIT); - v |= (flags & MXC_EHCI_INTERFACE_MASK) - << MX31_H2_SIC_SHIFT; - if (!(flags & MXC_EHCI_POWER_PINS_ENABLED)) - v |= MX31_H2_PM_BIT; - - if (!(flags & MXC_EHCI_TTL_ENABLED)) - v |= MX31_H2_DT_BIT; - - break; - default: - return -EINVAL; - } -#endif + if (!(flags & MXC_EHCI_POWER_PINS_ENABLED)) + v |= MX25_OTG_PM_BIT; + + if (flags & MXC_EHCI_PWR_PIN_ACTIVE_HIGH) + v |= MX25_OTG_PP_BIT; + + if (!(flags & MXC_EHCI_OC_PIN_ACTIVE_LOW)) + v |= MX25_OTG_OCPOL_BIT; + + break; + case 1: /* H1 port */ + v &= ~(MX25_H1_SIC_MASK | MX25_H1_PM_BIT | MX25_H1_PP_BIT | + MX25_H1_OCPOL_BIT | MX25_H1_TLL_BIT | + MX25_H1_USBTE_BIT | MX25_H1_IPPUE_DOWN_BIT | + MX25_H1_IPPUE_UP_BIT); + v |= (flags & MXC_EHCI_INTERFACE_MASK) << MX25_H1_SIC_SHIFT; + + if (!(flags & MXC_EHCI_POWER_PINS_ENABLED)) + v |= MX25_H1_PM_BIT; + + if (flags & MXC_EHCI_PWR_PIN_ACTIVE_HIGH) + v |= MX25_H1_PP_BIT; + + if (!(flags & MXC_EHCI_OC_PIN_ACTIVE_LOW)) + v |= MX25_H1_OCPOL_BIT; + + if (!(flags & MXC_EHCI_TTL_ENABLED)) + v |= MX25_H1_TLL_BIT; + + if (flags & MXC_EHCI_INTERNAL_PHY) + v |= MX25_H1_USBTE_BIT; + + if (flags & MXC_EHCI_IPPUE_DOWN) + v |= MX25_H1_IPPUE_DOWN_BIT; + + if (flags & MXC_EHCI_IPPUE_UP) + v |= MX25_H1_IPPUE_UP_BIT; + + break; + default: + return -EINVAL; + } +#elif defined(CONFIG_MX31) + switch (port) { + case 0: /* OTG port */ + v &= ~(MX31_OTG_SIC_MASK | MX31_OTG_PM_BIT); + v |= (flags & MXC_EHCI_INTERFACE_MASK) << MX31_OTG_SIC_SHIFT; + + if (!(flags & MXC_EHCI_POWER_PINS_ENABLED)) + v |= MX31_OTG_PM_BIT; + break; + case 1: /* H1 port */ + v &= ~(MX31_H1_SIC_MASK | MX31_H1_PM_BIT | MX31_H1_DT_BIT); + v |= (flags & MXC_EHCI_INTERFACE_MASK) << MX31_H1_SIC_SHIFT; + + if (!(flags & MXC_EHCI_POWER_PINS_ENABLED)) + v |= MX31_H1_PM_BIT; + + if (!(flags & MXC_EHCI_TTL_ENABLED)) + v |= MX31_H1_DT_BIT; + + break; + case 2: /* H2 port */ + v &= ~(MX31_H2_SIC_MASK | MX31_H2_PM_BIT | MX31_H2_DT_BIT); + v |= (flags & MXC_EHCI_INTERFACE_MASK) << MX31_H2_SIC_SHIFT; + + if (!(flags & MXC_EHCI_POWER_PINS_ENABLED)) + v |= MX31_H2_PM_BIT; + + if (!(flags & MXC_EHCI_TTL_ENABLED)) + v |= MX31_H2_DT_BIT; + + break; + default: + return -EINVAL; + } +#elif defined(CONFIG_MX35) + switch (port) { + case 0: /* OTG port */ + v &= ~(MX35_OTG_SIC_MASK | MX35_OTG_PM_BIT | MX35_OTG_PP_BIT | + MX35_OTG_OCPOL_BIT); + v |= (flags & MXC_EHCI_INTERFACE_MASK) << MX35_OTG_SIC_SHIFT; + + if (!(flags & MXC_EHCI_POWER_PINS_ENABLED)) + v |= MX35_OTG_PM_BIT; + + if (flags & MXC_EHCI_PWR_PIN_ACTIVE_HIGH) + v |= MX35_OTG_PP_BIT; + + if (!(flags & MXC_EHCI_OC_PIN_ACTIVE_LOW)) + v |= MX35_OTG_OCPOL_BIT; + + break; + case 1: /* H1 port */ + v &= ~(MX35_H1_SIC_MASK | MX35_H1_PM_BIT | MX35_H1_PP_BIT | + MX35_H1_OCPOL_BIT | MX35_H1_TLL_BIT | + MX35_H1_USBTE_BIT | MX35_H1_IPPUE_DOWN_BIT | + MX35_H1_IPPUE_UP_BIT); + v |= (flags & MXC_EHCI_INTERFACE_MASK) << MX35_H1_SIC_SHIFT; + + if (!(flags & MXC_EHCI_POWER_PINS_ENABLED)) + v |= MX35_H1_PM_BIT; + + if (flags & MXC_EHCI_PWR_PIN_ACTIVE_HIGH) + v |= MX35_H1_PP_BIT; + + if (!(flags & MXC_EHCI_OC_PIN_ACTIVE_LOW)) + v |= MX35_H1_OCPOL_BIT; + + if (!(flags & MXC_EHCI_TTL_ENABLED)) + v |= MX35_H1_TLL_BIT; + + if (flags & MXC_EHCI_INTERNAL_PHY) + v |= MX35_H1_USBTE_BIT; + + if (flags & MXC_EHCI_IPPUE_DOWN) + v |= MX35_H1_IPPUE_DOWN_BIT; + + if (flags & MXC_EHCI_IPPUE_UP) + v |= MX35_H1_IPPUE_UP_BIT; + + break; + default: + return -EINVAL; + } +#else +#error MXC EHCI USB driver not supported on this platform +#endif writel(v, IMX_USB_BASE + USBCTRL_OTGBASE_OFFSET); + return 0; } @@ -119,13 +234,17 @@ int ehci_hcd_init(int index, struct ehci_hccr **hccr, struct ehci_hcor **hcor) udelay(80); ehci = (struct usb_ehci *)(IMX_USB_BASE + - (0x200 * CONFIG_MXC_USB_PORT)); + IMX_USB_PORT_OFFSET * CONFIG_MXC_USB_PORT); *hccr = (struct ehci_hccr *)((uint32_t)&ehci->caplength); *hcor = (struct ehci_hcor *)((uint32_t) *hccr + HC_LENGTH(ehci_readl(&(*hccr)->cr_capbase))); setbits_le32(&ehci->usbmode, CM_HOST); __raw_writel(CONFIG_MXC_USB_PORTSC, &ehci->portsc); mxc_set_usbcontrol(CONFIG_MXC_USB_PORT, CONFIG_MXC_USB_FLAGS); +#ifdef CONFIG_MX35 + /* Workaround for ENGcm11601 */ + __raw_writel(0, &ehci->sbuscfg); +#endif udelay(10000); |