diff options
Diffstat (limited to 'board')
-rw-r--r-- | board/samsung/common/board.c | 180 | ||||
-rw-r--r-- | board/samsung/origen/origen.c | 112 | ||||
-rw-r--r-- | board/samsung/smdk5250/exynos5-dt.c | 15 | ||||
-rw-r--r-- | board/samsung/smdk5250/smdk5250.c | 125 | ||||
-rw-r--r-- | board/samsung/smdk5420/smdk5420.c | 15 | ||||
-rw-r--r-- | board/samsung/trats/trats.c | 213 | ||||
-rw-r--r-- | board/samsung/trats2/trats2.c | 233 | ||||
-rw-r--r-- | board/samsung/universal_c210/universal.c | 204 |
8 files changed, 265 insertions, 832 deletions
diff --git a/board/samsung/common/board.c b/board/samsung/common/board.c index cd873bc..e95e9c4 100644 --- a/board/samsung/common/board.c +++ b/board/samsung/common/board.c @@ -22,7 +22,8 @@ #include <asm/arch/power.h> #include <power/pmic.h> #include <asm/arch/sromc.h> -#include <power/max77686_pmic.h> +#include <lcd.h> +#include <samsung/misc.h> DECLARE_GLOBAL_DATA_PTR; @@ -33,6 +34,20 @@ struct local_info { static struct local_info local; +int __exynos_early_init_f(void) +{ + return 0; +} +int exynos_early_init_f(void) + __attribute__((weak, alias("__exynos_early_init_f"))); + +int __exynos_power_init(void) +{ + return 0; +} +int exynos_power_init(void) + __attribute__((weak, alias("__exynos_power_init"))); + #if defined CONFIG_EXYNOS_TMU /* Boot Time Thermal Analysis for SoC temperature threshold breach */ static void boot_temp_check(void) @@ -140,7 +155,7 @@ int board_early_init_f(void) board_i2c_init(gd->fdt_blob); #endif - return err; + return exynos_early_init_f(); } #endif @@ -161,134 +176,16 @@ static int board_init_cros_ec_devices(const void *blob) #endif #if defined(CONFIG_POWER) -#ifdef CONFIG_POWER_MAX77686 -static int pmic_reg_update(struct pmic *p, int reg, uint regval) -{ - u32 val; - int ret = 0; - - ret = pmic_reg_read(p, reg, &val); - if (ret) { - debug("%s: PMIC %d register read failed\n", __func__, reg); - return -1; - } - val |= regval; - ret = pmic_reg_write(p, reg, val); - if (ret) { - debug("%s: PMIC %d register write failed\n", __func__, reg); - return -1; - } - return 0; -} - -static int max77686_init(void) -{ - struct pmic *p; - - if (pmic_init(I2C_PMIC)) - return -1; - - p = pmic_get("MAX77686_PMIC"); - if (!p) - return -ENODEV; - - if (pmic_probe(p)) - return -1; - - if (pmic_reg_update(p, MAX77686_REG_PMIC_32KHZ, MAX77686_32KHCP_EN)) - return -1; - - if (pmic_reg_update(p, MAX77686_REG_PMIC_BBAT, - MAX77686_BBCHOSTEN | MAX77686_BBCVS_3_5V)) - return -1; - - /* VDD_MIF */ - if (pmic_reg_write(p, MAX77686_REG_PMIC_BUCK1OUT, - MAX77686_BUCK1OUT_1V)) { - debug("%s: PMIC %d register write failed\n", __func__, - MAX77686_REG_PMIC_BUCK1OUT); - return -1; - } - - if (pmic_reg_update(p, MAX77686_REG_PMIC_BUCK1CRTL, - MAX77686_BUCK1CTRL_EN)) - return -1; - - /* VDD_ARM */ - if (pmic_reg_write(p, MAX77686_REG_PMIC_BUCK2DVS1, - MAX77686_BUCK2DVS1_1_3V)) { - debug("%s: PMIC %d register write failed\n", __func__, - MAX77686_REG_PMIC_BUCK2DVS1); - return -1; - } - - if (pmic_reg_update(p, MAX77686_REG_PMIC_BUCK2CTRL1, - MAX77686_BUCK2CTRL_ON)) - return -1; - - /* VDD_INT */ - if (pmic_reg_write(p, MAX77686_REG_PMIC_BUCK3DVS1, - MAX77686_BUCK3DVS1_1_0125V)) { - debug("%s: PMIC %d register write failed\n", __func__, - MAX77686_REG_PMIC_BUCK3DVS1); - return -1; - } - - if (pmic_reg_update(p, MAX77686_REG_PMIC_BUCK3CTRL, - MAX77686_BUCK3CTRL_ON)) - return -1; - - /* VDD_G3D */ - if (pmic_reg_write(p, MAX77686_REG_PMIC_BUCK4DVS1, - MAX77686_BUCK4DVS1_1_2V)) { - debug("%s: PMIC %d register write failed\n", __func__, - MAX77686_REG_PMIC_BUCK4DVS1); - return -1; - } - - if (pmic_reg_update(p, MAX77686_REG_PMIC_BUCK4CTRL1, - MAX77686_BUCK3CTRL_ON)) - return -1; - - /* VDD_LDO2 */ - if (pmic_reg_update(p, MAX77686_REG_PMIC_LDO2CTRL1, - MAX77686_LD02CTRL1_1_5V | EN_LDO)) - return -1; - - /* VDD_LDO3 */ - if (pmic_reg_update(p, MAX77686_REG_PMIC_LDO3CTRL1, - MAX77686_LD03CTRL1_1_8V | EN_LDO)) - return -1; - - /* VDD_LDO5 */ - if (pmic_reg_update(p, MAX77686_REG_PMIC_LDO5CTRL1, - MAX77686_LD05CTRL1_1_8V | EN_LDO)) - return -1; - - /* VDD_LDO10 */ - if (pmic_reg_update(p, MAX77686_REG_PMIC_LDO10CTRL1, - MAX77686_LD10CTRL1_1_8V | EN_LDO)) - return -1; - - return 0; -} -#endif - int power_init_board(void) { - int ret = 0; - set_ps_hold_ctrl(); -#ifdef CONFIG_POWER_MAX77686 - ret = max77686_init(); -#endif - - return ret; + return exynos_power_init(); } #endif #ifdef CONFIG_OF_CONTROL +#ifdef CONFIG_SMC911X static int decode_sromc(const void *blob, struct fdt_sromc *config) { int err; @@ -312,6 +209,7 @@ static int decode_sromc(const void *blob, struct fdt_sromc *config) } return 0; } +#endif int board_eth_init(bd_t *bis) { @@ -369,15 +267,35 @@ int board_mmc_init(bd_t *bis) { int ret; +#ifdef CONFIG_SDHCI + /* mmc initializattion for available channels */ + ret = exynos_mmc_init(gd->fdt_blob); + if (ret) + debug("mmc init failed\n"); +#endif +#ifdef CONFIG_DWMMC /* dwmmc initializattion for available channels */ ret = exynos_dwmmc_init(gd->fdt_blob); if (ret) debug("dwmmc init failed\n"); +#endif return ret; } #endif + +#ifdef CONFIG_DISPLAY_BOARDINFO +int checkboard(void) +{ + const char *board_name; + + board_name = fdt_getprop(gd->fdt_blob, 0, "model", NULL); + printf("Board: %s\n", board_name ? board_name : "unknown"); + + return 0; +} #endif +#endif /* CONFIG_OF_CONTROL */ #ifdef CONFIG_BOARD_LATE_INIT int board_late_init(void) @@ -409,3 +327,21 @@ int arch_early_init_r(void) return 0; } + +#ifdef CONFIG_MISC_INIT_R +int misc_init_r(void) +{ +#ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG + set_board_info(); +#endif +#ifdef CONFIG_LCD_MENU + keys_init(); + check_boot_mode(); +#endif +#ifdef CONFIG_CMD_BMP + if (panel_info.logo_on) + draw_logo(); +#endif + return 0; +} +#endif diff --git a/board/samsung/origen/origen.c b/board/samsung/origen/origen.c index 15f77ca..d502f02 100644 --- a/board/samsung/origen/origen.c +++ b/board/samsung/origen/origen.c @@ -11,129 +11,35 @@ #include <asm/arch/mmc.h> #include <asm/arch/periph.h> #include <asm/arch/pinmux.h> +#include <usb.h> DECLARE_GLOBAL_DATA_PTR; -struct exynos4_gpio_part1 *gpio1; -struct exynos4_gpio_part2 *gpio2; -int board_init(void) +u32 get_board_rev(void) { - gpio1 = (struct exynos4_gpio_part1 *) EXYNOS4_GPIO_PART1_BASE; - gpio2 = (struct exynos4_gpio_part2 *) EXYNOS4_GPIO_PART2_BASE; - - gd->bd->bi_boot_params = (PHYS_SDRAM_1 + 0x100UL); return 0; } -static int board_uart_init(void) +int exynos_init(void) { - int err; - - err = exynos_pinmux_config(PERIPH_ID_UART0, PINMUX_FLAG_NONE); - if (err) { - debug("UART0 not configured\n"); - return err; - } - - err = exynos_pinmux_config(PERIPH_ID_UART1, PINMUX_FLAG_NONE); - if (err) { - debug("UART1 not configured\n"); - return err; - } - - err = exynos_pinmux_config(PERIPH_ID_UART2, PINMUX_FLAG_NONE); - if (err) { - debug("UART2 not configured\n"); - return err; - } - - err = exynos_pinmux_config(PERIPH_ID_UART3, PINMUX_FLAG_NONE); - if (err) { - debug("UART3 not configured\n"); - return err; - } - return 0; } -#ifdef CONFIG_BOARD_EARLY_INIT_F -int board_early_init_f(void) -{ - int err; - err = board_uart_init(); - if (err) { - debug("UART init failed\n"); - return err; - } - return err; -} -#endif - -int dram_init(void) +int board_usb_init(int index, enum usb_init_type init) { - gd->ram_size = get_ram_size((long *)PHYS_SDRAM_1, PHYS_SDRAM_1_SIZE) - + get_ram_size((long *)PHYS_SDRAM_2, PHYS_SDRAM_2_SIZE) - + get_ram_size((long *)PHYS_SDRAM_3, PHYS_SDRAM_3_SIZE) - + get_ram_size((long *)PHYS_SDRAM_4, PHYS_SDRAM_4_SIZE); - return 0; } -void dram_init_banksize(void) -{ - gd->bd->bi_dram[0].start = PHYS_SDRAM_1; - gd->bd->bi_dram[0].size = get_ram_size((long *)PHYS_SDRAM_1, \ - PHYS_SDRAM_1_SIZE); - gd->bd->bi_dram[1].start = PHYS_SDRAM_2; - gd->bd->bi_dram[1].size = get_ram_size((long *)PHYS_SDRAM_2, \ - PHYS_SDRAM_2_SIZE); - gd->bd->bi_dram[2].start = PHYS_SDRAM_3; - gd->bd->bi_dram[2].size = get_ram_size((long *)PHYS_SDRAM_3, \ - PHYS_SDRAM_3_SIZE); - gd->bd->bi_dram[3].start = PHYS_SDRAM_4; - gd->bd->bi_dram[3].size = get_ram_size((long *)PHYS_SDRAM_4, \ - PHYS_SDRAM_4_SIZE); -} - -#ifdef CONFIG_DISPLAY_BOARDINFO -int checkboard(void) +#ifdef CONFIG_USB_CABLE_CHECK +int usb_cable_connected(void) { - printf("\nBoard: ORIGEN\n"); return 0; } #endif -#ifdef CONFIG_GENERIC_MMC -int board_mmc_init(bd_t *bis) +#ifdef CONFIG_BOARD_EARLY_INIT_F +int exynos_early_init_f(void) { - int i, err; - - /* - * MMC2 SD card GPIO: - * - * GPK2[0] SD_2_CLK(2) - * GPK2[1] SD_2_CMD(2) - * GPK2[2] SD_2_CDn - * GPK2[3:6] SD_2_DATA[0:3](2) - */ - for (i = 0; i < 7; i++) { - /* GPK2[0:6] special function 2 */ - s5p_gpio_cfg_pin(&gpio2->k2, i, GPIO_FUNC(0x2)); - - /* GPK2[0:6] drv 4x */ - s5p_gpio_set_drv(&gpio2->k2, i, GPIO_DRV_4X); - - /* GPK2[0:1] pull disable */ - if (i == 0 || i == 1) { - s5p_gpio_set_pull(&gpio2->k2, i, GPIO_PULL_NONE); - continue; - } - - /* GPK2[2:6] pull up */ - s5p_gpio_set_pull(&gpio2->k2, i, GPIO_PULL_UP); - } - - err = s5p_mmc_init(2, 4); - return err; + return 0; } #endif diff --git a/board/samsung/smdk5250/exynos5-dt.c b/board/samsung/smdk5250/exynos5-dt.c index 5fb8664..b22fba5 100644 --- a/board/samsung/smdk5250/exynos5-dt.c +++ b/board/samsung/smdk5250/exynos5-dt.c @@ -45,21 +45,6 @@ int exynos_init(void) return 0; } -#ifdef CONFIG_DISPLAY_BOARDINFO -int checkboard(void) -{ - const char *board_name; - - board_name = fdt_getprop(gd->fdt_blob, 0, "model", NULL); - if (board_name == NULL) - printf("\nUnknown Board\n"); - else - printf("\nBoard: %s\n", board_name); - - return 0; -} -#endif - #ifdef CONFIG_LCD void exynos_cfg_lcd_gpio(void) { diff --git a/board/samsung/smdk5250/smdk5250.c b/board/samsung/smdk5250/smdk5250.c index a69f73d..28a6d9e 100644 --- a/board/samsung/smdk5250/smdk5250.c +++ b/board/samsung/smdk5250/smdk5250.c @@ -147,6 +147,131 @@ void board_i2c_init(const void *blob) } } +#if defined(CONFIG_POWER) +#ifdef CONFIG_POWER_MAX77686 +static int pmic_reg_update(struct pmic *p, int reg, uint regval) +{ + u32 val; + int ret = 0; + + ret = pmic_reg_read(p, reg, &val); + if (ret) { + debug("%s: PMIC %d register read failed\n", __func__, reg); + return -1; + } + val |= regval; + ret = pmic_reg_write(p, reg, val); + if (ret) { + debug("%s: PMIC %d register write failed\n", __func__, reg); + return -1; + } + return 0; +} + +static int max77686_init(void) +{ + struct pmic *p; + + if (pmic_init(I2C_PMIC)) + return -1; + + p = pmic_get("MAX77686_PMIC"); + if (!p) + return -ENODEV; + + if (pmic_probe(p)) + return -1; + + if (pmic_reg_update(p, MAX77686_REG_PMIC_32KHZ, MAX77686_32KHCP_EN)) + return -1; + + if (pmic_reg_update(p, MAX77686_REG_PMIC_BBAT, + MAX77686_BBCHOSTEN | MAX77686_BBCVS_3_5V)) + return -1; + + /* VDD_MIF */ + if (pmic_reg_write(p, MAX77686_REG_PMIC_BUCK1OUT, + MAX77686_BUCK1OUT_1V)) { + debug("%s: PMIC %d register write failed\n", __func__, + MAX77686_REG_PMIC_BUCK1OUT); + return -1; + } + + if (pmic_reg_update(p, MAX77686_REG_PMIC_BUCK1CRTL, + MAX77686_BUCK1CTRL_EN)) + return -1; + + /* VDD_ARM */ + if (pmic_reg_write(p, MAX77686_REG_PMIC_BUCK2DVS1, + MAX77686_BUCK2DVS1_1_3V)) { + debug("%s: PMIC %d register write failed\n", __func__, + MAX77686_REG_PMIC_BUCK2DVS1); + return -1; + } + + if (pmic_reg_update(p, MAX77686_REG_PMIC_BUCK2CTRL1, + MAX77686_BUCK2CTRL_ON)) + return -1; + + /* VDD_INT */ + if (pmic_reg_write(p, MAX77686_REG_PMIC_BUCK3DVS1, + MAX77686_BUCK3DVS1_1_0125V)) { + debug("%s: PMIC %d register write failed\n", __func__, + MAX77686_REG_PMIC_BUCK3DVS1); + return -1; + } + + if (pmic_reg_update(p, MAX77686_REG_PMIC_BUCK3CTRL, + MAX77686_BUCK3CTRL_ON)) + return -1; + + /* VDD_G3D */ + if (pmic_reg_write(p, MAX77686_REG_PMIC_BUCK4DVS1, + MAX77686_BUCK4DVS1_1_2V)) { + debug("%s: PMIC %d register write failed\n", __func__, + MAX77686_REG_PMIC_BUCK4DVS1); + return -1; + } + + if (pmic_reg_update(p, MAX77686_REG_PMIC_BUCK4CTRL1, + MAX77686_BUCK3CTRL_ON)) + return -1; + + /* VDD_LDO2 */ + if (pmic_reg_update(p, MAX77686_REG_PMIC_LDO2CTRL1, + MAX77686_LD02CTRL1_1_5V | EN_LDO)) + return -1; + + /* VDD_LDO3 */ + if (pmic_reg_update(p, MAX77686_REG_PMIC_LDO3CTRL1, + MAX77686_LD03CTRL1_1_8V | EN_LDO)) + return -1; + + /* VDD_LDO5 */ + if (pmic_reg_update(p, MAX77686_REG_PMIC_LDO5CTRL1, + MAX77686_LD05CTRL1_1_8V | EN_LDO)) + return -1; + + /* VDD_LDO10 */ + if (pmic_reg_update(p, MAX77686_REG_PMIC_LDO10CTRL1, + MAX77686_LD10CTRL1_1_8V | EN_LDO)) + return -1; + + return 0; +} +#endif /* CONFIG_POWER_MAX77686 */ + +int exynos_power_init(void) +{ + int ret = 0; + +#ifdef CONFIG_POWER_MAX77686 + ret = max77686_init(); +#endif + return ret; +} +#endif /* CONFIG_POWER */ + #ifdef CONFIG_LCD void exynos_cfg_lcd_gpio(void) { diff --git a/board/samsung/smdk5420/smdk5420.c b/board/samsung/smdk5420/smdk5420.c index 3ad2ad0..e4606ec 100644 --- a/board/samsung/smdk5420/smdk5420.c +++ b/board/samsung/smdk5420/smdk5420.c @@ -142,18 +142,3 @@ int board_get_revision(void) { return 0; } - -#ifdef CONFIG_DISPLAY_BOARDINFO -int checkboard(void) -{ - const char *board_name; - - board_name = fdt_getprop(gd->fdt_blob, 0, "model", NULL); - if (board_name == NULL) - printf("\nUnknown Board\n"); - else - printf("\nBoard: %s\n", board_name); - - return 0; -} -#endif diff --git a/board/samsung/trats/trats.c b/board/samsung/trats/trats.c index b725505..7c79e7b 100644 --- a/board/samsung/trats/trats.c +++ b/board/samsung/trats/trats.c @@ -12,23 +12,20 @@ #include <asm/io.h> #include <asm/arch/cpu.h> #include <asm/arch/gpio.h> -#include <asm/arch/mmc.h> #include <asm/arch/pinmux.h> #include <asm/arch/clock.h> -#include <asm/arch/clk.h> #include <asm/arch/mipi_dsim.h> #include <asm/arch/watchdog.h> #include <asm/arch/power.h> #include <power/pmic.h> #include <usb/s3c_udc.h> #include <power/max8997_pmic.h> -#include <libtizen.h> #include <power/max8997_muic.h> #include <power/battery.h> #include <power/max17042_fg.h> +#include <libtizen.h> #include <usb.h> #include <usb_mass_storage.h> -#include <samsung/misc.h> #include "setup.h" @@ -46,10 +43,8 @@ u32 get_board_rev(void) static void check_hw_revision(void); struct s3c_plat_otg_data s5pc210_otg_data; -int board_init(void) +int exynos_init(void) { - gd->bd->bi_boot_params = CONFIG_SYS_SPL_ARGS_ADDR; - check_hw_revision(); printf("HW Revision:\t0x%x\n", board_rev); @@ -281,7 +276,7 @@ static int pmic_init_max8997(void) return 0; } -int power_init_board(void) +int exynos_power_init(void) { int chrg, ret; struct power_battery *pb; @@ -350,28 +345,6 @@ int power_init_board(void) return 0; } -int dram_init(void) -{ - gd->ram_size = get_ram_size((long *)PHYS_SDRAM_1, PHYS_SDRAM_1_SIZE) + - get_ram_size((long *)PHYS_SDRAM_2, PHYS_SDRAM_2_SIZE) + - get_ram_size((long *)PHYS_SDRAM_3, PHYS_SDRAM_3_SIZE) + - get_ram_size((long *)PHYS_SDRAM_4, PHYS_SDRAM_4_SIZE); - - return 0; -} - -void dram_init_banksize(void) -{ - gd->bd->bi_dram[0].start = PHYS_SDRAM_1; - gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE; - gd->bd->bi_dram[1].start = PHYS_SDRAM_2; - gd->bd->bi_dram[1].size = PHYS_SDRAM_2_SIZE; - gd->bd->bi_dram[2].start = PHYS_SDRAM_3; - gd->bd->bi_dram[2].size = PHYS_SDRAM_3_SIZE; - gd->bd->bi_dram[3].start = PHYS_SDRAM_4; - gd->bd->bi_dram[3].size = PHYS_SDRAM_4_SIZE; -} - static unsigned int get_hw_revision(void) { struct exynos4_gpio_part1 *gpio = @@ -404,55 +377,6 @@ static void check_hw_revision(void) board_rev |= hwrev; } -#ifdef CONFIG_DISPLAY_BOARDINFO -int checkboard(void) -{ - puts("Board:\tTRATS\n"); - return 0; -} -#endif - -#ifdef CONFIG_GENERIC_MMC -int board_mmc_init(bd_t *bis) -{ - struct exynos4_gpio_part2 *gpio = - (struct exynos4_gpio_part2 *)samsung_get_base_gpio_part2(); - int err; - - /* eMMC_EN: SD_0_CDn: GPK0[2] Output High */ - s5p_gpio_direction_output(&gpio->k0, 2, 1); - s5p_gpio_set_pull(&gpio->k0, 2, GPIO_PULL_NONE); - - /* - * MMC device init - * mmc0 : eMMC (8-bit buswidth) - * mmc2 : SD card (4-bit buswidth) - */ - err = exynos_pinmux_config(PERIPH_ID_SDMMC0, PINMUX_FLAG_8BIT_MODE); - if (err) - debug("SDMMC0 not configured\n"); - else - err = s5p_mmc_init(0, 8); - - /* T-flash detect */ - s5p_gpio_cfg_pin(&gpio->x3, 4, 0xf); - s5p_gpio_set_pull(&gpio->x3, 4, GPIO_PULL_UP); - - /* - * Check the T-flash detect pin - * GPX3[4] T-flash detect pin - */ - if (!s5p_gpio_get_value(&gpio->x3, 4)) { - err = exynos_pinmux_config(PERIPH_ID_SDMMC2, PINMUX_FLAG_NONE); - if (err) - debug("SDMMC2 not configured\n"); - else - err = s5p_mmc_init(2, 4); - } - - return err; -} -#endif #ifdef CONFIG_USB_GADGET static int s5pc210_phy_control(int on) @@ -599,38 +523,22 @@ static void board_power_init(void) writel(0, (unsigned int)&pwr->arm_core1_configuration); } -static void board_uart_init(void) +static void exynos_uart_init(void) { - struct exynos4_gpio_part1 *gpio1 = - (struct exynos4_gpio_part1 *)samsung_get_base_gpio_part1(); struct exynos4_gpio_part2 *gpio2 = (struct exynos4_gpio_part2 *)samsung_get_base_gpio_part2(); - int i; - - /* - * UART2 GPIOs - * GPA1CON[0] = UART_2_RXD(2) - * GPA1CON[1] = UART_2_TXD(2) - * GPA1CON[2] = I2C_3_SDA (3) - * GPA1CON[3] = I2C_3_SCL (3) - */ - - for (i = 0; i < 4; i++) { - s5p_gpio_set_pull(&gpio1->a1, i, GPIO_PULL_NONE); - s5p_gpio_cfg_pin(&gpio1->a1, i, GPIO_FUNC((i > 1) ? 0x3 : 0x2)); - } /* UART_SEL GPY4[7] (part2) at EXYNOS4 */ s5p_gpio_set_pull(&gpio2->y4, 7, GPIO_PULL_UP); s5p_gpio_direction_output(&gpio2->y4, 7, 1); } -int board_early_init_f(void) +int exynos_early_init_f(void) { wdt_stop(); pmic_reset(); board_clock_init(); - board_uart_init(); + exynos_uart_init(); board_power_init(); return 0; @@ -648,7 +556,7 @@ void exynos_reset_lcd(void) s5p_gpio_direction_output(&gpio2->y4, 5, 1); } -static int lcd_power(void) +int lcd_power(void) { int ret = 0; struct pmic *p = pmic_get("MAX8997_PMIC"); @@ -671,46 +579,7 @@ static int lcd_power(void) return 0; } -static struct mipi_dsim_config dsim_config = { - .e_interface = DSIM_VIDEO, - .e_virtual_ch = DSIM_VIRTUAL_CH_0, - .e_pixel_format = DSIM_24BPP_888, - .e_burst_mode = DSIM_BURST_SYNC_EVENT, - .e_no_data_lane = DSIM_DATA_LANE_4, - .e_byte_clk = DSIM_PLL_OUT_DIV8, - .hfp = 1, - - .p = 3, - .m = 120, - .s = 1, - - /* D-PHY PLL stable time spec :min = 200usec ~ max 400usec */ - .pll_stable_time = 500, - - /* escape clk : 10MHz */ - .esc_clk = 20 * 1000000, - - /* stop state holding counter after bta change count 0 ~ 0xfff */ - .stop_holding_cnt = 0x7ff, - /* bta timeout 0 ~ 0xff */ - .bta_timeout = 0xff, - /* lp rx timeout 0 ~ 0xffff */ - .rx_timeout = 0xffff, -}; - -static struct exynos_platform_mipi_dsim s6e8ax0_platform_data = { - .lcd_panel_info = NULL, - .dsim_config = &dsim_config, -}; - -static struct mipi_dsim_lcd_device mipi_lcd_device = { - .name = "s6e8ax0", - .id = -1, - .bus_id = 0, - .platform_data = (void *)&s6e8ax0_platform_data, -}; - -static int mipi_power(void) +int mipi_power(void) { int ret = 0; struct pmic *p = pmic_get("MAX8997_PMIC"); @@ -733,75 +602,13 @@ static int mipi_power(void) return 0; } -vidinfo_t panel_info = { - .vl_freq = 60, - .vl_col = 720, - .vl_row = 1280, - .vl_width = 720, - .vl_height = 1280, - .vl_clkp = CONFIG_SYS_HIGH, - .vl_hsp = CONFIG_SYS_LOW, - .vl_vsp = CONFIG_SYS_LOW, - .vl_dp = CONFIG_SYS_LOW, - .vl_bpix = 4, /* Bits per pixel, 2^4 = 16 */ - - /* s6e8ax0 Panel infomation */ - .vl_hspw = 5, - .vl_hbpd = 10, - .vl_hfpd = 10, - - .vl_vspw = 2, - .vl_vbpd = 1, - .vl_vfpd = 13, - .vl_cmd_allow_len = 0xf, - - .win_id = 3, - .dual_lcd_enabled = 0, - - .init_delay = 0, - .power_on_delay = 0, - .reset_delay = 0, - .interface_mode = FIMD_RGB_INTERFACE, - .mipi_enabled = 1, -}; - -void init_panel_info(vidinfo_t *vid) +void exynos_lcd_misc_init(vidinfo_t *vid) { - vid->logo_on = 1, - vid->resolution = HD_RESOLUTION, - vid->rgb_mode = MODE_RGB_P, - #ifdef CONFIG_TIZEN get_tizen_logo_info(vid); #endif - mipi_lcd_device.reverse_panel = 1; - - strcpy(s6e8ax0_platform_data.lcd_panel_name, mipi_lcd_device.name); - s6e8ax0_platform_data.lcd_power = lcd_power; - s6e8ax0_platform_data.mipi_power = mipi_power; - s6e8ax0_platform_data.phy_enable = set_mipi_phy_ctrl; - s6e8ax0_platform_data.lcd_panel_info = (void *)vid; - exynos_mipi_dsi_register_lcd_device(&mipi_lcd_device); +#ifdef CONFIG_S6E8AX0 s6e8ax0_init(); - exynos_set_dsim_platform_data(&s6e8ax0_platform_data); - setenv("lcdinfo", "lcd=s6e8ax0"); -} - -#ifdef CONFIG_MISC_INIT_R -int misc_init_r(void) -{ -#ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG - set_board_info(); -#endif -#ifdef CONFIG_LCD_MENU - keys_init(); - check_boot_mode(); #endif -#ifdef CONFIG_CMD_BMP - if (panel_info.logo_on) - draw_logo(); -#endif - return 0; } -#endif diff --git a/board/samsung/trats2/trats2.c b/board/samsung/trats2/trats2.c index c17c24d..2a6c9f9 100644 --- a/board/samsung/trats2/trats2.c +++ b/board/samsung/trats2/trats2.c @@ -8,15 +8,9 @@ #include <common.h> #include <lcd.h> -#include <asm/io.h> -#include <asm/arch/gpio.h> -#include <asm/arch/mmc.h> -#include <asm/arch/power.h> -#include <asm/arch/clk.h> -#include <asm/arch/clock.h> -#include <asm/arch/mipi_dsim.h> #include <asm/arch/pinmux.h> #include <asm/arch/power.h> +#include <asm/arch/mipi_dsim.h> #include <power/pmic.h> #include <power/max77686_pmic.h> #include <power/battery.h> @@ -28,7 +22,6 @@ #include <usb.h> #include <usb/s3c_udc.h> #include <usb_mass_storage.h> -#include <samsung/misc.h> DECLARE_GLOBAL_DATA_PTR; @@ -69,16 +62,6 @@ static void check_hw_revision(void) board_rev = modelrev << 8; } -#ifdef CONFIG_DISPLAY_BOARDINFO -int checkboard(void) -{ - puts("Board:\tTRATS2\n"); - printf("HW Revision:\t0x%04x\n", board_rev); - - return 0; -} -#endif - u32 get_board_rev(void) { return board_rev; @@ -156,33 +139,24 @@ int get_soft_i2c_sda_pin(void) } #endif -int board_early_init_f(void) +int exynos_early_init_f(void) { - check_hw_revision(); board_external_gpio_init(); - gd->flags |= GD_FLG_DISABLE_CONSOLE; - return 0; } static int pmic_init_max77686(void); -int board_init(void) +int exynos_init(void) { - struct exynos4_power *pwr = - (struct exynos4_power *)samsung_get_base_power(); - - gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100; - - /* workaround: clear INFORM4..5 */ - writel(0, (unsigned int)&pwr->inform4); - writel(0, (unsigned int)&pwr->inform5); + check_hw_revision(); + printf("HW Revision:\t0x%04x\n", board_rev); return 0; } -int power_init_board(void) +int exynos_power_init(void) { int chrg; struct power_battery *pb; @@ -248,90 +222,6 @@ int power_init_board(void) return 0; } -int dram_init(void) -{ - u32 size_mb; - - size_mb = (get_ram_size((long *)PHYS_SDRAM_1, PHYS_SDRAM_1_SIZE) + - get_ram_size((long *)PHYS_SDRAM_2, PHYS_SDRAM_2_SIZE) + - get_ram_size((long *)PHYS_SDRAM_3, PHYS_SDRAM_3_SIZE) + - get_ram_size((long *)PHYS_SDRAM_4, PHYS_SDRAM_4_SIZE)) >> 20; - - gd->ram_size = size_mb << 20; - - return 0; -} - -void dram_init_banksize(void) -{ - gd->bd->bi_dram[0].start = PHYS_SDRAM_1; - gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE; - gd->bd->bi_dram[1].start = PHYS_SDRAM_2; - gd->bd->bi_dram[1].size = PHYS_SDRAM_2_SIZE; - gd->bd->bi_dram[2].start = PHYS_SDRAM_3; - gd->bd->bi_dram[2].size = PHYS_SDRAM_3_SIZE; - gd->bd->bi_dram[3].start = PHYS_SDRAM_4; - gd->bd->bi_dram[3].size = PHYS_SDRAM_4_SIZE; -} - -int board_mmc_init(bd_t *bis) -{ - int err0, err2 = 0; - - gpio2 = (struct exynos4x12_gpio_part2 *)samsung_get_base_gpio_part2(); - - /* eMMC_EN: SD_0_CDn: GPK0[2] Output High */ - s5p_gpio_direction_output(&gpio2->k0, 2, 1); - s5p_gpio_set_pull(&gpio2->k0, 2, GPIO_PULL_NONE); - - /* - * eMMC GPIO: - * SDR 8-bit@48MHz at MMC0 - * GPK0[0] SD_0_CLK(2) - * GPK0[1] SD_0_CMD(2) - * GPK0[2] SD_0_CDn -> Not used - * GPK0[3:6] SD_0_DATA[0:3](2) - * GPK1[3:6] SD_0_DATA[0:3](3) - * - * DDR 4-bit@26MHz at MMC4 - * GPK0[0] SD_4_CLK(3) - * GPK0[1] SD_4_CMD(3) - * GPK0[2] SD_4_CDn -> Not used - * GPK0[3:6] SD_4_DATA[0:3](3) - * GPK1[3:6] SD_4_DATA[4:7](4) - */ - - err0 = exynos_pinmux_config(PERIPH_ID_SDMMC0, PINMUX_FLAG_8BIT_MODE); - - /* - * MMC device init - * mmc0 : eMMC (8-bit buswidth) - * mmc2 : SD card (4-bit buswidth) - */ - if (err0) - debug("SDMMC0 not configured\n"); - else - err0 = s5p_mmc_init(0, 8); - - /* T-flash detect */ - s5p_gpio_cfg_pin(&gpio2->x3, 4, 0xf); - s5p_gpio_set_pull(&gpio2->x3, 4, GPIO_PULL_UP); - - /* - * Check the T-flash detect pin - * GPX3[4] T-flash detect pin - */ - if (!s5p_gpio_get_value(&gpio2->x3, 4)) { - err2 = exynos_pinmux_config(PERIPH_ID_SDMMC2, PINMUX_FLAG_NONE); - if (err2) - debug("SDMMC2 not configured\n"); - else - err2 = s5p_mmc_init(2, 4); - } - - return err0 & err2; -} - #ifdef CONFIG_USB_GADGET static int s5pc210_phy_control(int on) { @@ -479,46 +369,7 @@ static int pmic_init_max77686(void) */ #ifdef CONFIG_LCD -static struct mipi_dsim_config dsim_config = { - .e_interface = DSIM_VIDEO, - .e_virtual_ch = DSIM_VIRTUAL_CH_0, - .e_pixel_format = DSIM_24BPP_888, - .e_burst_mode = DSIM_BURST_SYNC_EVENT, - .e_no_data_lane = DSIM_DATA_LANE_4, - .e_byte_clk = DSIM_PLL_OUT_DIV8, - .hfp = 1, - - .p = 3, - .m = 120, - .s = 1, - - /* D-PHY PLL stable time spec :min = 200usec ~ max 400usec */ - .pll_stable_time = 500, - - /* escape clk : 10MHz */ - .esc_clk = 20 * 1000000, - - /* stop state holding counter after bta change count 0 ~ 0xfff */ - .stop_holding_cnt = 0x7ff, - /* bta timeout 0 ~ 0xff */ - .bta_timeout = 0xff, - /* lp rx timeout 0 ~ 0xffff */ - .rx_timeout = 0xffff, -}; - -static struct exynos_platform_mipi_dsim dsim_platform_data = { - .lcd_panel_info = NULL, - .dsim_config = &dsim_config, -}; - -static struct mipi_dsim_lcd_device mipi_lcd_device = { - .name = "s6e8ax0", - .id = -1, - .bus_id = 0, - .platform_data = (void *)&dsim_platform_data, -}; - -static int mipi_power(void) +int mipi_power(void) { struct pmic *p = pmic_get("MAX77686_PMIC"); @@ -556,77 +407,13 @@ void exynos_reset_lcd(void) s5p_gpio_set_value(&gpio1->f2, 1, 1); } -vidinfo_t panel_info = { - .vl_freq = 60, - .vl_col = 720, - .vl_row = 1280, - .vl_width = 720, - .vl_height = 1280, - .vl_clkp = CONFIG_SYS_HIGH, - .vl_hsp = CONFIG_SYS_LOW, - .vl_vsp = CONFIG_SYS_LOW, - .vl_dp = CONFIG_SYS_LOW, - .vl_bpix = 4, /* Bits per pixel, 2^4 = 16 */ - - /* s6e8ax0 Panel infomation */ - .vl_hspw = 5, - .vl_hbpd = 10, - .vl_hfpd = 10, - - .vl_vspw = 2, - .vl_vbpd = 1, - .vl_vfpd = 13, - .vl_cmd_allow_len = 0xf, - .mipi_enabled = 1, - - .dual_lcd_enabled = 0, - - .init_delay = 0, - .power_on_delay = 25, - .reset_delay = 0, - .interface_mode = FIMD_RGB_INTERFACE, -}; - -void init_panel_info(vidinfo_t *vid) +void exynos_lcd_misc_init(vidinfo_t *vid) { - vid->logo_on = 1; - vid->resolution = HD_RESOLUTION; - vid->rgb_mode = MODE_RGB_P; - - vid->power_on_delay = 30; - - mipi_lcd_device.reverse_panel = 1; - #ifdef CONFIG_TIZEN get_tizen_logo_info(vid); #endif - - strcpy(dsim_platform_data.lcd_panel_name, mipi_lcd_device.name); - dsim_platform_data.mipi_power = mipi_power; - dsim_platform_data.phy_enable = set_mipi_phy_ctrl; - dsim_platform_data.lcd_panel_info = (void *)vid; - exynos_mipi_dsi_register_lcd_device(&mipi_lcd_device); - +#ifdef CONFIG_S6E8AX0 s6e8ax0_init(); - - exynos_set_dsim_platform_data(&dsim_platform_data); -} -#endif /* LCD */ - -#ifdef CONFIG_MISC_INIT_R -int misc_init_r(void) -{ -#ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG - set_board_info(); -#endif -#ifdef CONFIG_LCD_MENU - keys_init(); - check_boot_mode(); #endif -#ifdef CONFIG_CMD_BMP - if (panel_info.logo_on) - draw_logo(); -#endif - return 0; } -#endif +#endif /* LCD */ diff --git a/board/samsung/universal_c210/universal.c b/board/samsung/universal_c210/universal.c index 96da7e0..f9d71b6 100644 --- a/board/samsung/universal_c210/universal.c +++ b/board/samsung/universal_c210/universal.c @@ -13,16 +13,17 @@ #include <asm/gpio.h> #include <asm/arch/adc.h> #include <asm/arch/gpio.h> -#include <asm/arch/mmc.h> #include <asm/arch/pinmux.h> #include <asm/arch/watchdog.h> -#include <libtizen.h> #include <ld9040.h> #include <power/pmic.h> +#include <usb.h> #include <usb/s3c_udc.h> #include <asm/arch/cpu.h> #include <power/max8998_pmic.h> +#include <libtizen.h> #include <samsung/misc.h> +#include <usb_mass_storage.h> DECLARE_GLOBAL_DATA_PTR; @@ -42,7 +43,7 @@ static int get_hwrev(void) static void init_pmic_lcd(void); -int power_init_board(void) +int exynos_power_init(void) { int ret; @@ -59,22 +60,6 @@ int power_init_board(void) return 0; } -int dram_init(void) -{ - gd->ram_size = get_ram_size((long *)PHYS_SDRAM_1, PHYS_SDRAM_1_SIZE) + - get_ram_size((long *)PHYS_SDRAM_2, PHYS_SDRAM_2_SIZE); - - return 0; -} - -void dram_init_banksize(void) -{ - gd->bd->bi_dram[0].start = PHYS_SDRAM_1; - gd->bd->bi_dram[0].size = PHYS_SDRAM_1_SIZE; - gd->bd->bi_dram[1].start = PHYS_SDRAM_2; - gd->bd->bi_dram[1].size = PHYS_SDRAM_2_SIZE; -} - static unsigned short get_adc_value(int channel) { struct s5p_adc *adc = (struct s5p_adc *)samsung_get_base_adc(); @@ -159,71 +144,6 @@ static void check_hw_revision(void) board_rev |= hwrev; } -#ifdef CONFIG_DISPLAY_BOARDINFO -int checkboard(void) -{ - puts("Board:\tUniversal C210\n"); - return 0; -} -#endif - -#ifdef CONFIG_GENERIC_MMC -int board_mmc_init(bd_t *bis) -{ - int err; - - switch (get_hwrev()) { - case 0: - /* - * Set the low to enable LDO_EN - * But when you use the test board for eMMC booting - * you should set it HIGH since it removes the inverter - */ - /* MASSMEMORY_EN: XMDMDATA_6: GPE3[6] */ - s5p_gpio_direction_output(&gpio1->e3, 6, 0); - break; - default: - /* - * Default reset state is High and there's no inverter - * But set it as HIGH to ensure - */ - /* MASSMEMORY_EN: XMDMADDR_3: GPE1[3] */ - s5p_gpio_direction_output(&gpio1->e1, 3, 1); - break; - } - - /* - * MMC device init - * mmc0 : eMMC (8-bit buswidth) - * mmc2 : SD card (4-bit buswidth) - */ - err = exynos_pinmux_config(PERIPH_ID_SDMMC0, PINMUX_FLAG_8BIT_MODE); - if (err) - debug("SDMMC0 not configured\n"); - else - err = s5p_mmc_init(0, 8); - - /* T-flash detect */ - s5p_gpio_cfg_pin(&gpio2->x3, 4, 0xf); - s5p_gpio_set_pull(&gpio2->x3, 4, GPIO_PULL_UP); - - /* - * Check the T-flash detect pin - * GPX3[4] T-flash detect pin - */ - if (!s5p_gpio_get_value(&gpio2->x3, 4)) { - err = exynos_pinmux_config(PERIPH_ID_SDMMC2, PINMUX_FLAG_NONE); - if (err) - debug("SDMMC2 not configured\n"); - else - err = s5p_mmc_init(2, 4); - } - - return err; - -} -#endif - #ifdef CONFIG_USB_GADGET static int s5pc210_phy_control(int on) { @@ -271,7 +191,20 @@ struct s3c_plat_otg_data s5pc210_otg_data = { }; #endif -int board_early_init_f(void) +int board_usb_init(int index, enum usb_init_type init) +{ + debug("USB_udc_probe\n"); + return s3c_udc_probe(&s5pc210_otg_data); +} + +#ifdef CONFIG_USB_CABLE_CHECK +int usb_cable_connected(void) +{ + return 0; +} +#endif + +int exynos_early_init_f(void) { wdt_stop(); @@ -412,6 +345,11 @@ void exynos_cfg_lcd_gpio(void) spi_init(); } +int mipi_power(void) +{ + return 0; +} + void exynos_reset_lcd(void) { s5p_gpio_set_value(&gpio2->y4, 5, 1); @@ -436,39 +374,6 @@ void exynos_lcd_power_on(void) pmic_set_output(p, MAX8998_REG_ONOFF2, MAX8998_LDO7, LDO_ON); } -vidinfo_t panel_info = { - .vl_freq = 60, - .vl_col = 480, - .vl_row = 800, - .vl_width = 480, - .vl_height = 800, - .vl_clkp = CONFIG_SYS_HIGH, - .vl_hsp = CONFIG_SYS_HIGH, - .vl_vsp = CONFIG_SYS_HIGH, - .vl_dp = CONFIG_SYS_HIGH, - - .vl_bpix = 4, /* Bits per pixel */ - - /* LD9040 LCD Panel */ - .vl_hspw = 2, - .vl_hbpd = 16, - .vl_hfpd = 16, - - .vl_vspw = 2, - .vl_vbpd = 8, - .vl_vfpd = 8, - .vl_cmd_allow_len = 0xf, - - .win_id = 0, - .dual_lcd_enabled = 0, - - .init_delay = 0, - .power_on_delay = 10000, - .reset_delay = 10000, - .interface_mode = FIMD_RGB_INTERFACE, - .mipi_enabled = 0, -}; - void exynos_cfg_ldo(void) { ld9040_cfg_ldo(); @@ -479,30 +384,32 @@ void exynos_enable_ldo(unsigned int onoff) ld9040_enable_ldo(onoff); } -void init_panel_info(vidinfo_t *vid) -{ - vid->logo_on = 1; - vid->resolution = HD_RESOLUTION; - vid->rgb_mode = MODE_RGB_P; - -#ifdef CONFIG_TIZEN - get_tizen_logo_info(vid); -#endif - - /* for LD9040. */ - vid->pclk_name = 1; /* MPLL */ - vid->sclk_div = 1; - - setenv("lcdinfo", "lcd=ld9040"); -} - -int board_init(void) +int exynos_init(void) { gpio1 = (struct exynos4_gpio_part1 *) EXYNOS4_GPIO_PART1_BASE; gpio2 = (struct exynos4_gpio_part2 *) EXYNOS4_GPIO_PART2_BASE; gd->bd->bi_arch_number = MACH_TYPE_UNIVERSAL_C210; - gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100; + + switch (get_hwrev()) { + case 0: + /* + * Set the low to enable LDO_EN + * But when you use the test board for eMMC booting + * you should set it HIGH since it removes the inverter + */ + /* MASSMEMORY_EN: XMDMDATA_6: GPE3[6] */ + s5p_gpio_direction_output(&gpio1->e3, 6, 0); + break; + default: + /* + * Default reset state is High and there's no inverter + * But set it as HIGH to ensure + */ + /* MASSMEMORY_EN: XMDMADDR_3: GPE1[3] */ + s5p_gpio_direction_output(&gpio1->e1, 3, 1); + break; + } #ifdef CONFIG_SOFT_SPI soft_spi_init(); @@ -513,20 +420,15 @@ int board_init(void) return 0; } -#ifdef CONFIG_MISC_INIT_R -int misc_init_r(void) +void exynos_lcd_misc_init(vidinfo_t *vid) { -#ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG - set_board_info(); -#endif -#ifdef CONFIG_LCD_MENU - keys_init(); - check_boot_mode(); -#endif -#ifdef CONFIG_CMD_BMP - if (panel_info.logo_on) - draw_logo(); +#ifdef CONFIG_TIZEN + get_tizen_logo_info(vid); #endif - return 0; + + /* for LD9040. */ + vid->pclk_name = 1; /* MPLL */ + vid->sclk_div = 1; + + setenv("lcdinfo", "lcd=ld9040"); } -#endif |