diff options
Diffstat (limited to 'board')
34 files changed, 2516 insertions, 40 deletions
diff --git a/board/LaCie/common/common.c b/board/LaCie/common/common.c index 78d0edc..a62bf9f 100644 --- a/board/LaCie/common/common.c +++ b/board/LaCie/common/common.c @@ -13,10 +13,11 @@ #if defined(CONFIG_CMD_NET) && defined(CONFIG_RESET_PHY_R) +#define MII_MARVELL_PHY_PAGE 22 + #define MV88E1116_LED_FCTRL_REG 10 #define MV88E1116_CPRSP_CR3_REG 21 #define MV88E1116_MAC_CTRL_REG 21 -#define MV88E1116_PGADR_REG 22 #define MV88E1116_RGMII_TXTM_CTRL (1 << 4) #define MV88E1116_RGMII_RXTM_CTRL (1 << 5) @@ -31,15 +32,44 @@ void mv_phy_88e1116_init(const char *name, u16 phyaddr) * Enable RGMII delay on Tx and Rx for CPU port * Ref: sec 4.7.2 of chip datasheet */ - miiphy_write(name, phyaddr, MV88E1116_PGADR_REG, 2); + miiphy_write(name, phyaddr, MII_MARVELL_PHY_PAGE, 2); miiphy_read(name, phyaddr, MV88E1116_MAC_CTRL_REG, ®); reg |= (MV88E1116_RGMII_RXTM_CTRL | MV88E1116_RGMII_TXTM_CTRL); miiphy_write(name, phyaddr, MV88E1116_MAC_CTRL_REG, reg); - miiphy_write(name, phyaddr, MV88E1116_PGADR_REG, 0); + miiphy_write(name, phyaddr, MII_MARVELL_PHY_PAGE, 0); if (miiphy_reset(name, phyaddr) == 0) printf("88E1116 Initialized on %s\n", name); } + +void mv_phy_88e1318_init(const char *name, u16 phyaddr) +{ + u16 reg; + + if (miiphy_set_current_dev(name)) + return; + + /* + * Set control mode 4 for LED[0]. + */ + miiphy_write(name, phyaddr, MII_MARVELL_PHY_PAGE, 3); + miiphy_read(name, phyaddr, 16, ®); + reg |= 0xf; + miiphy_write(name, phyaddr, 16, reg); + + /* + * Enable RGMII delay on Tx and Rx for CPU port + * Ref: sec 4.7.2 of chip datasheet + */ + miiphy_write(name, phyaddr, MII_MARVELL_PHY_PAGE, 2); + miiphy_read(name, phyaddr, MV88E1116_MAC_CTRL_REG, ®); + reg |= (MV88E1116_RGMII_TXTM_CTRL | MV88E1116_RGMII_RXTM_CTRL); + miiphy_write(name, phyaddr, MV88E1116_MAC_CTRL_REG, reg); + miiphy_write(name, phyaddr, MII_MARVELL_PHY_PAGE, 0); + + if (miiphy_reset(name, phyaddr) == 0) + printf("88E1318 Initialized on %s\n", name); +} #endif /* CONFIG_CMD_NET && CONFIG_RESET_PHY_R */ #if defined(CONFIG_CMD_I2C) && defined(CONFIG_SYS_I2C_EEPROM_ADDR) diff --git a/board/LaCie/common/common.h b/board/LaCie/common/common.h index 2edd5ab..85e433c 100644 --- a/board/LaCie/common/common.h +++ b/board/LaCie/common/common.h @@ -12,6 +12,7 @@ #if defined(CONFIG_CMD_NET) && defined(CONFIG_RESET_PHY_R) void mv_phy_88e1116_init(const char *name, u16 phyaddr); +void mv_phy_88e1318_init(const char *name, u16 phyaddr); #endif #if defined(CONFIG_CMD_I2C) && defined(CONFIG_SYS_I2C_EEPROM_ADDR) int lacie_read_mac_address(uchar *mac); diff --git a/board/LaCie/netspace_v2/kwbimage-ns2l.cfg b/board/LaCie/netspace_v2/kwbimage-ns2l.cfg new file mode 100644 index 0000000..d008eb0 --- /dev/null +++ b/board/LaCie/netspace_v2/kwbimage-ns2l.cfg @@ -0,0 +1,162 @@ +# +# Copyright (C) 2011 Simon Guinot <sguinot@lacie.com> +# +# Based on Kirkwood support: +# (C) Copyright 2009 +# Marvell Semiconductor <www.marvell.com> +# Written-by: Prafulla Wadaskar <prafulla@marvell.com> +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# Refer docs/README.kwimage for more details about how-to configure +# and create kirkwood boot image +# + +# Boot Media configurations +BOOT_FROM spi # Boot from SPI flash + +# SOC registers configuration using bootrom header extension +# Maximum KWBIMAGE_MAX_CONFIG configurations allowed + +# Configure RGMII-0 interface pad voltage to 1.8V +DATA 0xFFD100e0 0x1B1B1B9B + +#Dram initalization for SINGLE x16 CL=5 @ 400MHz +DATA 0xFFD01400 0x43000618 # DDR Configuration register +# bit13-0: 0xa00 (2560 DDR2 clks refresh rate) +# bit23-14: zero +# bit24: 1= enable exit self refresh mode on DDR access +# bit25: 1 required +# bit29-26: zero +# bit31-30: 01 + +DATA 0xFFD01404 0x34143000 # DDR Controller Control Low +# bit 4: 0=addr/cmd in smame cycle +# bit 5: 0=clk is driven during self refresh, we don't care for APX +# bit 6: 0=use recommended falling edge of clk for addr/cmd +# bit14: 0=input buffer always powered up +# bit18: 1=cpu lock transaction enabled +# bit23-20: 5=recommended value for CL=5 and STARTBURST_DEL disabled bit31=0 +# bit27-24: 8= CL+3, STARTBURST sample stages, for freqs 400MHz, unbuffered DIMM +# bit30-28: 3 required +# bit31: 0=no additional STARTBURST delay + +DATA 0xFFD01408 0x11012228 # DDR Timing (Low) (active cycles value +1) +# bit7-4: TRCD +# bit11- 8: TRP +# bit15-12: TWR +# bit19-16: TWTR +# bit20: TRAS msb +# bit23-21: 0x0 +# bit27-24: TRRD +# bit31-28: TRTP + +DATA 0xFFD0140C 0x00000A19 # DDR Timing (High) +# bit6-0: TRFC +# bit8-7: TR2R +# bit10-9: TR2W +# bit12-11: TW2W +# bit31-13: zero required + +DATA 0xFFD01410 0x0000DDDD # DDR Address Control +# bit1-0: 00, Cs0width=x8 +# bit3-2: 10, Cs0size=512Mb +# bit5-4: 00, Cs2width=nonexistent +# bit7-6: 00, Cs1size =nonexistent +# bit9-8: 00, Cs2width=nonexistent +# bit11-10: 00, Cs2size =nonexistent +# bit13-12: 00, Cs3width=nonexistent +# bit15-14: 00, Cs3size =nonexistent +# bit16: 0, Cs0AddrSel +# bit17: 0, Cs1AddrSel +# bit18: 0, Cs2AddrSel +# bit19: 0, Cs3AddrSel +# bit31-20: 0 required + +DATA 0xFFD01414 0x00000000 # DDR Open Pages Control +# bit0: 0, OpenPage enabled +# bit31-1: 0 required + +DATA 0xFFD01418 0x00000000 # DDR Operation +# bit3-0: 0x0, DDR cmd +# bit31-4: 0 required + +DATA 0xFFD0141C 0x00000632 # DDR Mode +# bit2-0: 2, BurstLen=2 required +# bit3: 0, BurstType=0 required +# bit6-4: 4, CL=5 +# bit7: 0, TestMode=0 normal +# bit8: 0, DLL reset=0 normal +# bit11-9: 6, auto-precharge write recovery ???????????? +# bit12: 0, PD must be zero +# bit31-13: 0 required + +DATA 0xFFD01420 0x00000004 # DDR Extended Mode +# bit0: 0, DDR DLL enabled +# bit1: 1, DDR drive strenght reduced +# bit2: 1, DDR ODT control lsd enabled +# bit5-3: 000, required +# bit6: 1, DDR ODT control msb, enabled +# bit9-7: 000, required +# bit10: 0, differential DQS enabled +# bit11: 0, required +# bit12: 0, DDR output buffer enabled +# bit31-13: 0 required + +DATA 0xFFD01424 0x0000F07F # DDR Controller Control High +# bit2-0: 111, required +# bit3 : 1 , MBUS Burst Chop disabled +# bit6-4: 111, required +# bit7 : 1 , D2P Latency enabled +# bit8 : 1 , add writepath sample stage, must be 1 for DDR freq >= 300MHz +# bit9 : 0 , no half clock cycle addition to dataout +# bit10 : 0 , 1/4 clock cycle skew enabled for addr/ctl signals +# bit11 : 0 , 1/4 clock cycle skew disabled for write mesh +# bit15-12: 1111 required +# bit31-16: 0 required + +DATA 0xFFD01428 0x00085520 # DDR2 ODT Read Timing (default values) +DATA 0xFFD0147C 0x00008552 # DDR2 ODT Write Timing (default values) + +DATA 0xFFD01500 0x00000000 # CS[0]n Base address to 0x0 +DATA 0xFFD01504 0x07FFFFF1 # CS[0]n Size +# bit0: 1, Window enabled +# bit1: 0, Write Protect disabled +# bit3-2: 00, CS0 hit selected +# bit23-4: ones, required +# bit31-24: 0x07, Size (i.e. 128MB) + +DATA 0xFFD0150C 0x00000000 # CS[1]n Size, window disabled +DATA 0xFFD01514 0x00000000 # CS[2]n Size, window disabled +DATA 0xFFD0151C 0x00000000 # CS[3]n Size, window disabled + +DATA 0xFFD01494 0x00010000 # DDR ODT Control (Low) +# bit3-0: 1, ODT0Rd, MODT[0] asserted during read from DRAM CS0 +# bit19-16:1, ODT0Wr, MODT[0] asserted during write to DRAM CS0 + +DATA 0xFFD01498 0x00000000 # DDR ODT Control (High) +# bit1-0: 00, ODT0 controlled by ODT Control (low) register above +# bit3-2: 01, ODT1 active NEVER! +# bit31-4: zero, required + +DATA 0xFFD0149C 0x0000E40F # CPU ODT Control +# bit3-0: 1, ODT0Rd, Internal ODT asserted during read from DRAM bank0 +# bit7-4: 1, ODT0Wr, Internal ODT asserted during write to DRAM bank0 +# bit11-10:1, DQ_ODTSel. ODT select turned on + +DATA 0xFFD01480 0x00000001 # DDR Initialization Control +#bit0=1, enable DDR init upon this register write + +# End of Header extension +DATA 0x0 0x0 diff --git a/board/LaCie/netspace_v2/netspace_v2.c b/board/LaCie/netspace_v2/netspace_v2.c index 68e8a77..101a80a 100644 --- a/board/LaCie/netspace_v2/netspace_v2.c +++ b/board/LaCie/netspace_v2/netspace_v2.c @@ -107,7 +107,11 @@ int misc_init_r(void) /* Configure and initialize PHY */ void reset_phy(void) { +#if defined(CONFIG_NETSPACE_LITE_V2) || defined(CONFIG_NETSPACE_MINI_V2) + mv_phy_88e1318_init("egiga0", 0); +#else mv_phy_88e1116_init("egiga0", 8); +#endif } #endif diff --git a/board/altera/socfpga_cyclone5/Makefile b/board/altera/socfpga_cyclone5/Makefile new file mode 100644 index 0000000..43bbc37 --- /dev/null +++ b/board/altera/socfpga_cyclone5/Makefile @@ -0,0 +1,50 @@ +# +# (C) Copyright 2001-2006 +# Wolfgang Denk, DENX Software Engineering, wd@denx.de. +# (C) Copyright 2010, Thomas Chou <thomas@wytron.com.tw> +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +include $(TOPDIR)/config.mk + +LIB = $(obj)lib$(BOARD).o + +COBJS := socfpga_cyclone5.o + +SRCS := $(COBJS:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS)) + +$(LIB): $(obj).depend $(OBJS) + $(call cmd_link_o_target, $(OBJS)) + +clean: + rm -f $(OBJS) + +distclean: clean + rm -f $(LIB) core *.bak $(obj).depend + +######################################################################### + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################### diff --git a/board/altera/socfpga_cyclone5/socfpga_cyclone5.c b/board/altera/socfpga_cyclone5/socfpga_cyclone5.c new file mode 100644 index 0000000..7725be1 --- /dev/null +++ b/board/altera/socfpga_cyclone5/socfpga_cyclone5.c @@ -0,0 +1,80 @@ +/* + * Copyright (C) 2012 Altera Corporation <www.altera.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ + +#include <common.h> +#include <asm/arch/reset_manager.h> +#include <asm/io.h> + +#include <netdev.h> + +DECLARE_GLOBAL_DATA_PTR; + +/* + * Print CPU information + */ +int print_cpuinfo(void) +{ + puts("CPU : Altera SOCFPGA Platform\n"); + return 0; +} + +/* + * Print Board information + */ +int checkboard(void) +{ + puts("BOARD : Altera SOCFPGA Cyclone5 Board\n"); + return 0; +} + +/* + * Initialization function which happen at early stage of c code + */ +int board_early_init_f(void) +{ + return 0; +} + +/* + * Miscellaneous platform dependent initialisations + */ +int board_init(void) +{ + icache_enable(); + return 0; +} + +int misc_init_r(void) +{ + return 0; +} + +#if defined(CONFIG_SYS_CONSOLE_IS_IN_ENV) && defined(CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE) +int overwrite_console(void) +{ + return 0; +} +#endif + +/* + * DesignWare Ethernet initialization + */ +/* We know all the init functions have been run now */ +int board_eth_init(bd_t *bis) +{ + return 0; +} diff --git a/board/atmark-techno/armadillo-800eva/Makefile b/board/atmark-techno/armadillo-800eva/Makefile new file mode 100644 index 0000000..9f9618b --- /dev/null +++ b/board/atmark-techno/armadillo-800eva/Makefile @@ -0,0 +1,46 @@ +# +# Copyright (C) 2012 Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA + +include $(TOPDIR)/config.mk + +LIB = $(obj)lib$(BOARD).o + +COBJS-y += armadillo-800eva.o +COBJS := $(COBJS-y) + +SRCS := $(COBJS:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS)) + +$(LIB): $(obj).depend $(OBJS) + $(call cmd_link_o_target, $(OBJS)) + +clean: + rm -f $(OBJS) + +distclean: clean + rm -f $(LIB) core *.bak $(obj).depend + +######################################################################### + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################### + diff --git a/board/atmark-techno/armadillo-800eva/armadillo-800eva.c b/board/atmark-techno/armadillo-800eva/armadillo-800eva.c new file mode 100644 index 0000000..0e9c222 --- /dev/null +++ b/board/atmark-techno/armadillo-800eva/armadillo-800eva.c @@ -0,0 +1,328 @@ +/* + * Copyright (C) 2012 Renesas Solutions Corp. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <common.h> +#include <malloc.h> +#include <asm/processor.h> +#include <asm/mach-types.h> +#include <asm/io.h> +#include <asm/arch/sys_proto.h> +#include <asm/gpio.h> +#include <asm/arch/rmobile.h> + +#define s_init_wait(cnt) \ + ({ \ + volatile u32 i = 0x10000 * cnt; \ + while (i > 0) \ + i--; \ + }) + +#define USBCR1 0xE605810A + +void s_init(void) +{ + struct r8a7740_rwdt *rwdt0 = (struct r8a7740_rwdt *)RWDT0_BASE; + struct r8a7740_rwdt *rwdt1 = (struct r8a7740_rwdt *)RWDT1_BASE; + struct r8a7740_cpg *cpg = (struct r8a7740_cpg *)CPG_BASE; + struct r8a7740_bsc *bsc = (struct r8a7740_bsc *)BSC_BASE; + struct r8a7740_ddrp *ddrp = (struct r8a7740_ddrp *)DDRP_BASE; + struct r8a7740_dbsc *dbsc = (struct r8a7740_dbsc *)DBSC_BASE; + + /* Watchdog init */ + writew(0xA500, &rwdt0->rwtcsra0); + writew(0xA500, &rwdt1->rwtcsra0); + + /* CPG */ + writel(0xFF800080, &cpg->rmstpcr4); + writel(0xFF800080, &cpg->smstpcr4); + + /* USB clock */ + writel(0x00000080, &cpg->usbckcr); + s_init_wait(1); + + /* USBCR1 */ + writew(0x0710, USBCR1); + + /* FRQCR */ + writel(0x00000000, &cpg->frqcrb); + writel(0x62030533, &cpg->frqcra); + writel(0x208A354E, &cpg->frqcrc); + writel(0x80331050, &cpg->frqcrb); + s_init_wait(1); + + writel(0x00000000, &cpg->frqcrd); + s_init_wait(1); + + /* SUBClk */ + writel(0x0000010B, &cpg->subckcr); + + /* PLL */ + writel(0x00004004, &cpg->pllc01cr); + s_init_wait(1); + + writel(0xa0000000, &cpg->pllc2cr); + s_init_wait(2); + + /* BSC */ + writel(0x0000001B, &bsc->cmncr); + + writel(0x20000000, &dbsc->dbcmd); + writel(0x10009C40, &dbsc->dbcmd); + s_init_wait(1); + + writel(0x00000007, &dbsc->dbkind); + writel(0x0E030A02, &dbsc->dbconf0); + writel(0x00000001, &dbsc->dbphytype); + writel(0x00000000, &dbsc->dbbl); + writel(0x00000006, &dbsc->dbtr0); + writel(0x00000005, &dbsc->dbtr1); + writel(0x00000000, &dbsc->dbtr2); + writel(0x00000006, &dbsc->dbtr3); + writel(0x00080006, &dbsc->dbtr4); + writel(0x00000015, &dbsc->dbtr5); + writel(0x0000000f, &dbsc->dbtr6); + writel(0x00000004, &dbsc->dbtr7); + writel(0x00000018, &dbsc->dbtr8); + writel(0x00000006, &dbsc->dbtr9); + writel(0x00000006, &dbsc->dbtr10); + writel(0x0000000F, &dbsc->dbtr11); + writel(0x0000000D, &dbsc->dbtr12); + writel(0x000000A0, &dbsc->dbtr13); + writel(0x000A0003, &dbsc->dbtr14); + writel(0x00000003, &dbsc->dbtr15); + writel(0x40005005, &dbsc->dbtr16); + writel(0x0C0C0000, &dbsc->dbtr17); + writel(0x00000200, &dbsc->dbtr18); + writel(0x00000040, &dbsc->dbtr19); + writel(0x00000001, &dbsc->dbrnk0); + writel(0x00000110, &dbsc->dbdficnt); + writel(0x00000101, &ddrp->funcctrl); + writel(0x00000001, &ddrp->dllctrl); + writel(0x00000186, &ddrp->zqcalctrl); + writel(0xB3440051, &ddrp->zqodtctrl); + writel(0x94449443, &ddrp->rdctrl); + writel(0x000000C0, &ddrp->rdtmg); + writel(0x00000101, &ddrp->fifoinit); + writel(0x02060506, &ddrp->outctrl); + writel(0x00004646, &ddrp->dqcalofs1); + writel(0x00004646, &ddrp->dqcalofs2); + writel(0x800000aa, &ddrp->dqcalexp); + writel(0x00000000, &ddrp->dllctrl); + writel(0x00000000, DDRPNCNT); + + writel(0x0000000C, &dbsc->dbcmd); + readl(&dbsc->dbwait); + s_init_wait(1); + + writel(0x00000002, DDRPNCNT); + + writel(0x0000000C, &dbsc->dbcmd); + readl(&dbsc->dbwait); + s_init_wait(1); + + writel(0x00000187, &ddrp->zqcalctrl); + + writel(0x00009C40, &dbsc->dbcmd); + readl(&dbsc->dbwait); + s_init_wait(1); + + writel(0x00009C40, &dbsc->dbcmd); + readl(&dbsc->dbwait); + s_init_wait(1); + + writel(0x00000010, &dbsc->dbdficnt); + writel(0x02060507, &ddrp->outctrl); + + writel(0x00009C40, &dbsc->dbcmd); + readl(&dbsc->dbwait); + s_init_wait(1); + + writel(0x21009C40, &dbsc->dbcmd); + readl(&dbsc->dbwait); + s_init_wait(1); + + writel(0x00009C40, &dbsc->dbcmd); + readl(&dbsc->dbwait); + s_init_wait(1); + + writel(0x00009C40, &dbsc->dbcmd); + readl(&dbsc->dbwait); + s_init_wait(1); + + writel(0x00009C40, &dbsc->dbcmd); + readl(&dbsc->dbwait); + s_init_wait(1); + + writel(0x00009C40, &dbsc->dbcmd); + readl(&dbsc->dbwait); + s_init_wait(1); + + writel(0x11000044, &dbsc->dbcmd); + readl(&dbsc->dbwait); + s_init_wait(1); + + writel(0x2A000000, &dbsc->dbcmd); + readl(&dbsc->dbwait); + s_init_wait(1); + + writel(0x2B000000, &dbsc->dbcmd); + readl(&dbsc->dbwait); + + writel(0x29000004, &dbsc->dbcmd); + readl(&dbsc->dbwait); + + writel(0x28001520, &dbsc->dbcmd); + readl(&dbsc->dbwait); + s_init_wait(1); + + writel(0x03000200, &dbsc->dbcmd); + readl(&dbsc->dbwait); + s_init_wait(1); + + writel(0x000001FF, &dbsc->dbrfcnf0); + writel(0x00010C30, &dbsc->dbrfcnf1); + writel(0x00000000, &dbsc->dbrfcnf2); + + writel(0x00000001, &dbsc->dbrfen); + writel(0x00000001, &dbsc->dbacen); + + /* BSC */ + writel(0x00410400, &bsc->cs0bcr); + writel(0x00410400, &bsc->cs2bcr); + writel(0x00410400, &bsc->cs5bbcr); + writel(0x02CB0400, &bsc->cs6abcr); + + writel(0x00000440, &bsc->cs0wcr); + writel(0x00000440, &bsc->cs2wcr); + writel(0x00000240, &bsc->cs5bwcr); + writel(0x00000240, &bsc->cs6awcr); + + writel(0x00000005, &bsc->rbwtcnt); + writel(0x00000002, &bsc->cs0wcr2); + writel(0x00000002, &bsc->cs2wcr2); + writel(0x00000002, &bsc->cs4wcr2); +} + +#define GPIO_ICCR (0xE60581A0) +#define ICCR_15BIT (1 << 15) /* any time 1 */ +#define IIC0_CONTA (1 << 7) +#define IIC0_CONTB (1 << 6) +#define IIC1_CONTA (1 << 5) +#define IIC1_CONTB (1 << 4) +#define IIC0_PS33E (1 << 1) +#define IIC1_PS33E (1 << 0) +#define GPIO_ICCR_DATA \ + (ICCR_15BIT | \ + IIC0_CONTA | IIC0_CONTB | IIC1_CONTA | \ + IIC1_CONTB | IIC0_PS33E | IIC1_PS33E) + +#define MSTPCR1 0xE6150134 +#define TMU0_MSTP125 (1 << 25) +#define I2C0_MSTP116 (1 << 16) + +#define MSTPCR3 0xE615013C +#define I2C1_MSTP323 (1 << 23) +#define GETHER_MSTP309 (1 << 9) + +#define GPIO_SCIFA1_TXD (0xE60520C4) +#define GPIO_SCIFA1_RXD (0xE60520C3) + +int board_early_init_f(void) +{ + /* TMU */ + clrbits_le32(MSTPCR1, TMU0_MSTP125); + + /* GETHER */ + clrbits_le32(MSTPCR3, GETHER_MSTP309); + + /* I2C 0/1 */ + clrbits_le32(MSTPCR1, I2C0_MSTP116); + clrbits_le32(MSTPCR3, I2C1_MSTP323); + + /* SCIFA1 */ + writeb(1, GPIO_SCIFA1_TXD); /* SCIFA1_TXD */ + writeb(1, GPIO_SCIFA1_RXD); /* SCIFA1_RXD */ + + /* IICCR */ + writew(GPIO_ICCR_DATA, GPIO_ICCR); + + return 0; +} + +DECLARE_GLOBAL_DATA_PTR; +int board_init(void) +{ + /* board id for linux */ + gd->bd->bi_arch_number = MACH_TYPE_ARMADILLO_800EVA; + /* adress of boot parameters */ + gd->bd->bi_boot_params = ARMADILLO_800EVA_SDRAM_BASE + 0x100; + + /* Init PFC controller */ + r8a7740_pinmux_init(); + + /* GETHER Enable */ + gpio_request(GPIO_FN_ET_CRS, NULL); + gpio_request(GPIO_FN_ET_MDC, NULL); + gpio_request(GPIO_FN_ET_MDIO, NULL); + gpio_request(GPIO_FN_ET_TX_ER, NULL); + gpio_request(GPIO_FN_ET_RX_ER, NULL); + gpio_request(GPIO_FN_ET_ERXD0, NULL); + gpio_request(GPIO_FN_ET_ERXD1, NULL); + gpio_request(GPIO_FN_ET_ERXD2, NULL); + gpio_request(GPIO_FN_ET_ERXD3, NULL); + gpio_request(GPIO_FN_ET_TX_CLK, NULL); + gpio_request(GPIO_FN_ET_TX_EN, NULL); + gpio_request(GPIO_FN_ET_ETXD0, NULL); + gpio_request(GPIO_FN_ET_ETXD1, NULL); + gpio_request(GPIO_FN_ET_ETXD2, NULL); + gpio_request(GPIO_FN_ET_ETXD3, NULL); + gpio_request(GPIO_FN_ET_PHY_INT, NULL); + gpio_request(GPIO_FN_ET_COL, NULL); + gpio_request(GPIO_FN_ET_RX_DV, NULL); + gpio_request(GPIO_FN_ET_RX_CLK, NULL); + + gpio_request(GPIO_PORT18, NULL); /* PHY_RST */ + gpio_direction_output(GPIO_PORT18, 1); + + return 0; +} + +int dram_init(void) +{ + gd->bd->bi_dram[0].start = CONFIG_SYS_SDRAM_BASE; + gd->ram_size = CONFIG_SYS_SDRAM_SIZE; + + return 0; +} + +const struct rmobile_sysinfo sysinfo = { + CONFIG_RMOBILE_BOARD_STRING +}; + +int board_late_init(void) +{ + return 0; +} + +void reset_cpu(ulong addr) +{ +} diff --git a/board/atmel/at91sam9x5ek/at91sam9x5ek.c b/board/atmel/at91sam9x5ek/at91sam9x5ek.c index ae408bc..06028aa 100644 --- a/board/atmel/at91sam9x5ek/at91sam9x5ek.c +++ b/board/atmel/at91sam9x5ek/at91sam9x5ek.c @@ -62,6 +62,10 @@ static void at91sam9x5ek_nand_hw_init(void) csa |= AT91_MATRIX_EBI_CS3A_SMC_SMARTMEDIA; /* NAND flash on D16 */ csa |= AT91_MATRIX_NFD0_ON_D16; + + /* Configure IO drive */ + csa &= ~AT91_MATRIX_EBI_EBI_IOSR_NORMAL; + writel(csa, &matrix->ebicsa); /* Configure SMC CS3 for NAND/SmartMedia */ diff --git a/board/buffalo/lsxl/lsxl.c b/board/buffalo/lsxl/lsxl.c index b3f31d6..57776fb 100644 --- a/board/buffalo/lsxl/lsxl.c +++ b/board/buffalo/lsxl/lsxl.c @@ -195,9 +195,11 @@ int board_init(void) static void check_power_switch(void) { if (kw_gpio_get_value(GPIO_POWER_SWITCH)) { - /* turn off HDD and USB power */ + /* turn off fan, HDD and USB power */ kw_gpio_set_value(GPIO_HDD_POWER, 0); kw_gpio_set_value(GPIO_USB_VBUS, 0); + kw_gpio_set_value(GPIO_FAN_HIGH, 1); + kw_gpio_set_value(GPIO_FAN_LOW, 1); set_led(LED_OFF); /* loop until released */ @@ -207,6 +209,8 @@ static void check_power_switch(void) /* turn power on again */ kw_gpio_set_value(GPIO_HDD_POWER, 1); kw_gpio_set_value(GPIO_USB_VBUS, 1); + kw_gpio_set_value(GPIO_FAN_HIGH, 0); + kw_gpio_set_value(GPIO_FAN_LOW, 0); set_led(LED_POWER_BLINKING); } } diff --git a/board/davinci/ea20/ea20.c b/board/davinci/ea20/ea20.c index 7e00040..0edd910 100644 --- a/board/davinci/ea20/ea20.c +++ b/board/davinci/ea20/ea20.c @@ -176,6 +176,9 @@ int board_early_init_f(void) if (davinci_configure_pin_mux(gpio_pins, ARRAY_SIZE(gpio_pins)) != 0) return 1; + /* Set DISP_ON high to enable LCD output*/ + gpio_direction_output(97, 1); + /* Set the RESETOUTn low */ gpio_direction_output(111, 0); @@ -188,9 +191,6 @@ int board_early_init_f(void) /* Set LCD_B_PWR low to power down LCD Backlight*/ gpio_direction_output(102, 0); - /* Set DISP_ON low to disable LCD output*/ - gpio_direction_output(97, 0); - #ifndef CONFIG_USE_IRQ irq_init(); #endif @@ -250,15 +250,19 @@ int board_early_init_f(void) writel(readl(&davinci_syscfg_regs->mstpri[2]) & 0x0fffffff, &davinci_syscfg_regs->mstpri[2]); - /* Set LCD_B_PWR low to power up LCD Backlight*/ - gpio_set_value(102, 1); - - /* Set DISP_ON low to disable LCD output*/ - gpio_set_value(97, 1); return 0; } +/* + * Do not overwrite the console + * Use always serial for U-Boot console + */ +int overwrite_console(void) +{ + return 1; +} + int board_init(void) { /* arch number of the board */ @@ -276,6 +280,9 @@ int board_init(void) int board_late_init(void) { + unsigned char buf[2]; + int ret; + /* PinMux for HALTEN */ if (davinci_configure_pin_mux(halten_pin, ARRAY_SIZE(halten_pin)) != 0) return 1; @@ -283,8 +290,15 @@ int board_late_init(void) /* Set HALTEN to high */ gpio_direction_output(134, 1); - setenv("stdout", "serial"); + /* Set fixed contrast settings for LCD via I2C potentiometer */ + buf[0] = 0x00; + buf[1] = 0xd7; + ret = i2c_write(0x2e, 6, 1, buf, 2); + if (ret) + puts("\nContrast Settings FAILED\n"); + /* Set LCD_B_PWR high to power up LCD Backlight*/ + gpio_set_value(102, 1); return 0; } #endif /* CONFIG_BOARD_LATE_INIT */ diff --git a/board/freescale/mx28evk/mx28evk.c b/board/freescale/mx28evk/mx28evk.c index d782aea..6e719ff 100644 --- a/board/freescale/mx28evk/mx28evk.c +++ b/board/freescale/mx28evk/mx28evk.c @@ -100,19 +100,6 @@ int board_mmc_init(bd_t *bis) #ifdef CONFIG_CMD_NET -#define MII_OPMODE_STRAP_OVERRIDE 0x16 -#define MII_PHY_CTRL1 0x1e -#define MII_PHY_CTRL2 0x1f - -int fecmxc_mii_postcall(int phy) -{ - miiphy_write("FEC1", phy, MII_BMCR, 0x9000); - miiphy_write("FEC1", phy, MII_OPMODE_STRAP_OVERRIDE, 0x0202); - if (phy == 3) - miiphy_write("FEC1", 3, MII_PHY_CTRL2, 0x8180); - return 0; -} - int board_eth_init(bd_t *bis) { struct mxs_clkctrl_regs *clkctrl_regs = @@ -152,24 +139,12 @@ int board_eth_init(bd_t *bis) return -EINVAL; } - ret = fecmxc_register_mii_postcall(dev, fecmxc_mii_postcall); - if (ret) { - puts("FEC MXS: Unable to register FEC0 mii postcall\n"); - return ret; - } - dev = eth_get_dev_by_name("FEC1"); if (!dev) { puts("FEC MXS: Unable to get FEC1 device entry\n"); return -EINVAL; } - ret = fecmxc_register_mii_postcall(dev, fecmxc_mii_postcall); - if (ret) { - puts("FEC MXS: Unable to register FEC1 mii postcall\n"); - return ret; - } - return ret; } diff --git a/board/freescale/mx51evk/mx51evk.c b/board/freescale/mx51evk/mx51evk.c index 7a0682a..a94701c 100644 --- a/board/freescale/mx51evk/mx51evk.c +++ b/board/freescale/mx51evk/mx51evk.c @@ -60,6 +60,14 @@ int dram_init(void) return 0; } +u32 get_board_rev(void) +{ + u32 rev = get_cpu_rev(); + if (!gpio_get_value(IMX_GPIO_NR(1, 22))) + rev |= BOARD_REV_2_0 << BOARD_VER_OFFSET; + return rev; +} + static void setup_iomux_uart(void) { unsigned int pad = PAD_CTL_HYS_ENABLE | PAD_CTL_PKE_ENABLE | diff --git a/board/friendlyarm/mini2440/Makefile b/board/friendlyarm/mini2440/Makefile new file mode 100644 index 0000000..b88e569 --- /dev/null +++ b/board/friendlyarm/mini2440/Makefile @@ -0,0 +1,44 @@ +# +# (C) Copyright 2012 +# Wolfgang Denk, DENX Software Engineering, wd@denx.de. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +include $(TOPDIR)/config.mk + +LIB = $(obj)lib$(BOARD).o + +COBJS := mini2440.o + +SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS)) +SOBJS := $(addprefix $(obj),$(SOBJS)) + +$(LIB): $(obj).depend $(OBJS) $(SOBJS) + $(call cmd_link_o_target, $(OBJS) $(SOBJS)) + +######################################################################### + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################### diff --git a/board/friendlyarm/mini2440/mini2440.c b/board/friendlyarm/mini2440/mini2440.c new file mode 100644 index 0000000..e97d981 --- /dev/null +++ b/board/friendlyarm/mini2440/mini2440.c @@ -0,0 +1,134 @@ +/* + * (C) Copyright 2002 + * Sysgo Real-Time Solutions, GmbH <www.elinos.com> + * Marius Groeger <mgroeger@sysgo.de> + * + * (C) Copyright 2002 + * David Mueller, ELSOFT AG, <d.mueller@elsoft.ch> + * + * (C) Copyright 2009 + * Michel Pollet <buserror@gmail.com> + * + * (C) Copyright 2012 + * Gabriel Huau <contact@huau-gabriel.fr> + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <common.h> +#include <asm/arch/s3c2440.h> +#include <asm/arch/iomux.h> +#include <asm/arch/gpio.h> +#include <asm/io.h> +#include <asm/gpio.h> +#include <netdev.h> +#include "mini2440.h" + +DECLARE_GLOBAL_DATA_PTR; + +static inline void pll_delay(unsigned long loops) +{ + __asm__ volatile ("1:\n" + "subs %0, %1, #1\n" + "bne 1b" : "=r" (loops) : "0" (loops)); +} + +int board_early_init_f(void) +{ + struct s3c24x0_clock_power * const clk_power = + s3c24x0_get_base_clock_power(); + + /* to reduce PLL lock time, adjust the LOCKTIME register */ + clk_power->locktime = 0xFFFFFF; /* Max PLL Lock time count */ + clk_power->clkdivn = CLKDIVN_VAL; + + /* configure UPLL */ + clk_power->upllcon = ((U_M_MDIV << 12) + (U_M_PDIV << 4) + U_M_SDIV); + /* some delay between MPLL and UPLL */ + pll_delay(100); + + /* configure MPLL */ + clk_power->mpllcon = ((M_MDIV << 12) + (M_PDIV << 4) + M_SDIV); + + /* some delay between MPLL and UPLL */ + pll_delay(10000); + + return 0; +} + +/* + * Miscellaneous platform dependent initialisations + */ +int board_init(void) +{ + struct s3c24x0_gpio * const gpio = s3c24x0_get_base_gpio(); + + /* IOMUX Port H : UART Configuration */ + gpio->gphcon = IOMUXH_nCTS0 | IOMUXH_nRTS0 | IOMUXH_TXD0 | IOMUXH_RXD0 | + IOMUXH_TXD1 | IOMUXH_RXD1 | IOMUXH_TXD2 | IOMUXH_RXD2; + + gpio_direction_output(GPH8, 0); + gpio_direction_output(GPH9, 0); + gpio_direction_output(GPH10, 0); + + /* adress of boot parameters */ + gd->bd->bi_boot_params = CONFIG_BOOT_PARAM_ADDR; + + return 0; +} + +int dram_init(void) +{ + struct s3c24x0_memctl *memctl = s3c24x0_get_base_memctl(); + + /* + * Configuring bus width and timing + * Initialize clocks for each bank 0..5 + * Bank 3 and 4 are used for DM9000 + */ + writel(BANK_CONF, &memctl->bwscon); + writel(B0_CONF, &memctl->bankcon[0]); + writel(B1_CONF, &memctl->bankcon[1]); + writel(B2_CONF, &memctl->bankcon[2]); + writel(B3_CONF, &memctl->bankcon[3]); + writel(B4_CONF, &memctl->bankcon[4]); + writel(B5_CONF, &memctl->bankcon[5]); + + /* Bank 6 and 7 are used for DRAM */ + writel(SDRAM_64MB, &memctl->bankcon[6]); + writel(SDRAM_64MB, &memctl->bankcon[7]); + + writel(MEM_TIMING, &memctl->refresh); + writel(BANKSIZE_CONF, &memctl->banksize); + writel(B6_MRSR, &memctl->mrsrb6); + writel(B7_MRSR, &memctl->mrsrb7); + + gd->ram_size = get_ram_size((void *) CONFIG_SYS_SDRAM_BASE, + PHYS_SDRAM_SIZE); + return 0; +} + +int board_eth_init(bd_t *bis) +{ +#ifdef CONFIG_DRIVER_DM9000 + return dm9000_initialize(bis); +#else + return 0; +#endif +} diff --git a/board/friendlyarm/mini2440/mini2440.h b/board/friendlyarm/mini2440/mini2440.h new file mode 100644 index 0000000..db386ea --- /dev/null +++ b/board/friendlyarm/mini2440/mini2440.h @@ -0,0 +1,144 @@ +#ifndef __MINI2440_BOARD_CONF_H__ +#define __MINI2440_BOARD_CONF_H__ + +/* PLL Parameters */ +#define CLKDIVN_VAL 7 +#define M_MDIV 0x7f +#define M_PDIV 0x2 +#define M_SDIV 0x1 + +#define U_M_MDIV 0x38 +#define U_M_PDIV 0x2 +#define U_M_SDIV 0x2 + +/* BWSCON */ +#define DW8 0x0 +#define DW16 0x1 +#define DW32 0x2 +#define WAIT (0x1<<2) +#define UBLB (0x1<<3) + +#define B1_BWSCON (DW32) +#define B2_BWSCON (DW16) +#define B3_BWSCON (DW16 + WAIT + UBLB) +#define B4_BWSCON (DW16 + WAIT + UBLB) +#define B5_BWSCON (DW16) +#define B6_BWSCON (DW32) +#define B7_BWSCON (DW32) + +/* + * Bank Configuration + */ +#define B0_Tacs 0x0 /* 0clk */ +#define B0_Tcos 0x0 /* 0clk */ +#define B0_Tacc 0x7 /* 14clk */ +#define B0_Tcoh 0x0 /* 0clk */ +#define B0_Tah 0x0 /* 0clk */ +#define B0_Tacp 0x0 /* 0clk */ +#define B0_PMC 0x0 /* normal */ + +#define B1_Tacs 0x0 +#define B1_Tcos 0x0 +#define B1_Tacc 0x7 +#define B1_Tcoh 0x0 +#define B1_Tah 0x0 +#define B1_Tacp 0x0 +#define B1_PMC 0x0 + +#define B2_Tacs 0x0 +#define B2_Tcos 0x0 +#define B2_Tacc 0x7 +#define B2_Tcoh 0x0 +#define B2_Tah 0x0 +#define B2_Tacp 0x0 +#define B2_PMC 0x0 + +#define B3_Tacs 0x0 +#define B3_Tcos 0x3 /* 4clk */ +#define B3_Tacc 0x7 +#define B3_Tcoh 0x1 /* 1clk */ +#define B3_Tah 0x3 /* 4clk */ +#define B3_Tacp 0x0 +#define B3_PMC 0x0 + +#define B4_Tacs 0x0 +#define B4_Tcos 0x3 +#define B4_Tacc 0x7 +#define B4_Tcoh 0x1 +#define B4_Tah 0x3 +#define B4_Tacp 0x0 +#define B4_PMC 0x0 + +#define B5_Tacs 0x0 +#define B5_Tcos 0x0 +#define B5_Tacc 0x7 +#define B5_Tcoh 0x0 +#define B5_Tah 0x0 +#define B5_Tacp 0x0 +#define B5_PMC 0x0 + +/* + * SDRAM Configuration + */ +#define SDRAM_MT 0x3 /* SDRAM */ +#define SDRAM_Trcd 0x0 /* 2clk */ +#define SDRAM_SCAN_9 0x1 /* 9bit */ +#define SDRAM_SCAN_10 0x2 /* 10bit */ + +#define SDRAM_64MB ((SDRAM_MT<<15) + (SDRAM_Trcd<<2) + (SDRAM_SCAN_9)) + +/* + * Refresh Parameter + */ +#define REFEN 0x1 /* Refresh enable */ +#define TREFMD 0x0 /* CBR(CAS before RAS)/Auto refresh */ +#define Trp 0x1 /* 3clk */ +#define Trc 0x3 /* 7clk */ +#define Tchr 0x0 /* unused */ +#define REFCNT 1012 /* period=10.37us, HCLK=100Mhz, (2048 + 1-10.37*100) */ + +/* + * MRSR Parameter + */ +#define BL 0x0 +#define BT 0x0 +#define CL 0x3 /* 3 clocks */ +#define TM 0x0 +#define WBL 0x0 + +/* + * BankSize Parameter + */ +#define BK76MAP 0x2 /* 128MB/128MB */ +#define SCLK_EN 0x1 /* SCLK active */ +#define SCKE_EN 0x1 /* SDRAM power down mode enable */ +#define BURST_EN 0x1 /* Burst enable */ + +/* + * Register values + */ +#define BANK_CONF ((0 + (B1_BWSCON<<4) + (B2_BWSCON<<8) + (B3_BWSCON<<12) + \ + (B4_BWSCON<<16) + (B5_BWSCON<<20) + (B6_BWSCON<<24) + \ + (B7_BWSCON<<28))) + +#define B0_CONF ((B0_Tacs<<13) + (B0_Tcos<<11) + (B0_Tacc<<8) + \ + (B0_Tcoh<<6) + (B0_Tah<<4) + (B0_Tacp<<2) + (B0_PMC)) +#define B1_CONF ((B1_Tacs<<13) + (B1_Tcos<<11) + (B1_Tacc<<8) + \ + (B1_Tcoh<<6) + (B1_Tah<<4) + (B1_Tacp<<2) + (B1_PMC)) +#define B2_CONF ((B2_Tacs<<13) + (B2_Tcos<<11) + (B2_Tacc<<8) + \ + (B2_Tcoh<<6) + (B2_Tah<<4) + (B2_Tacp<<2) + (B2_PMC)) +#define B3_CONF ((B3_Tacs<<13) + (B3_Tcos<<11) + (B3_Tacc<<8) + \ + (B3_Tcoh<<6) + (B3_Tah<<4) + (B3_Tacp<<2) + (B3_PMC)) +#define B4_CONF ((B4_Tacs<<13) + (B4_Tcos<<11) + (B4_Tacc<<8) + \ + (B4_Tcoh<<6) + (B4_Tah<<4) + (B4_Tacp<<2) + (B4_PMC)) +#define B5_CONF ((B5_Tacs<<13) + (B5_Tcos<<11) + (B5_Tacc<<8) + \ + (B5_Tcoh<<6) + (B5_Tah<<4) + (B5_Tacp<<2) + (B5_PMC)) + +#define MEM_TIMING (REFEN<<23) + (TREFMD<<22) + (Trp<<20) + \ + (Trc<<18) + (Tchr<<16) + REFCNT + +#define BANKSIZE_CONF (BK76MAP) + (SCLK_EN<<4) + (SCKE_EN<<5) + (BURST_EN<<7) +#define B6_MRSR (CL<<4) +#define B7_MRSR (CL<<4) + +#endif diff --git a/board/iomega/iconnect/Makefile b/board/iomega/iconnect/Makefile new file mode 100644 index 0000000..f77fcfb --- /dev/null +++ b/board/iomega/iconnect/Makefile @@ -0,0 +1,43 @@ +# +# (C) Copyright 2009 +# Marvell Semiconductor <www.marvell.com> +# Written-by: Prafulla Wadaskar <prafulla@marvell.com> +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program. If not, see <http://www.gnu.org/licenses/>. +# + +include $(TOPDIR)/config.mk + +LIB = $(obj)lib$(BOARD).o + +COBJS := iconnect.o + +SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS)) +SOBJS := $(addprefix $(obj),$(SOBJS)) + +$(LIB): $(obj).depend $(OBJS) $(SOBJS) + $(call cmd_link_o_target, $(OBJS) $(SOBJS)) + +######################################################################### + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################### diff --git a/board/iomega/iconnect/iconnect.c b/board/iomega/iconnect/iconnect.c new file mode 100644 index 0000000..6ee2128 --- /dev/null +++ b/board/iomega/iconnect/iconnect.c @@ -0,0 +1,107 @@ +/* + * Copyright (C) 2009-2012 + * Wojciech Dubowik <wojciech.dubowik@neratec.com> + * Luka Perkov <uboot@lukaperkov.net> + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ + +#include <common.h> +#include <miiphy.h> +#include <asm/arch/cpu.h> +#include <asm/arch/kirkwood.h> +#include <asm/arch/mpp.h> +#include "iconnect.h" + +DECLARE_GLOBAL_DATA_PTR; + +int board_early_init_f(void) +{ + /* + * default gpio configuration + * There are maximum 64 gpios controlled through 2 sets of registers + * the below configuration configures mainly initial LED status + */ + kw_config_gpio(ICONNECT_OE_VAL_LOW, + ICONNECT_OE_VAL_HIGH, + ICONNECT_OE_LOW, ICONNECT_OE_HIGH); + + /* Multi-Purpose Pins Functionality configuration */ + u32 kwmpp_config[] = { + MPP0_NF_IO2, + MPP1_NF_IO3, + MPP2_NF_IO4, + MPP3_NF_IO5, + MPP4_NF_IO6, + MPP5_NF_IO7, + MPP6_SYSRST_OUTn, /* Reset signal */ + MPP7_GPO, + MPP8_TW_SDA, /* I2C */ + MPP9_TW_SCK, /* I2C */ + MPP10_UART0_TXD, + MPP11_UART0_RXD, + MPP12_GPO, /* Reset button */ + MPP13_SD_CMD, + MPP14_SD_D0, + MPP15_SD_D1, + MPP16_SD_D2, + MPP17_SD_D3, + MPP18_NF_IO0, + MPP19_NF_IO1, + MPP20_GE1_0, + MPP21_GE1_1, + MPP22_GE1_2, + MPP23_GE1_3, + MPP24_GE1_4, + MPP25_GE1_5, + MPP26_GE1_6, + MPP27_GE1_7, + MPP28_GPIO, + MPP29_GPIO, + MPP30_GE1_10, + MPP31_GE1_11, + MPP32_GE1_12, + MPP33_GE1_13, + MPP34_GE1_14, + MPP35_GPIO, /* OTB button */ + MPP36_AUDIO_SPDIFI, + MPP37_AUDIO_SPDIFO, + MPP38_GPIO, + MPP39_TDM_SPI_CS0, + MPP40_TDM_SPI_SCK, + MPP41_GPIO, /* LED brightness */ + MPP42_GPIO, /* LED power (blue) */ + MPP43_GPIO, /* LED power (red) */ + MPP44_GPIO, /* LED USB 1 */ + MPP45_GPIO, /* LED USB 2 */ + MPP46_GPIO, /* LED USB 3 */ + MPP47_GPIO, /* LED USB 4 */ + MPP48_GPIO, /* LED OTB */ + MPP49_GPIO, + 0 + }; + kirkwood_mpp_conf(kwmpp_config, NULL); + return 0; +} + +int board_init(void) +{ + /* adress of boot parameters */ + gd->bd->bi_boot_params = kw_sdram_bar(0) + 0x100; + + return 0; +} diff --git a/board/iomega/iconnect/iconnect.h b/board/iomega/iconnect/iconnect.h new file mode 100644 index 0000000..2fb3e5e --- /dev/null +++ b/board/iomega/iconnect/iconnect.h @@ -0,0 +1,39 @@ +/* + * Copyright (C) 2009-2012 + * Wojciech Dubowik <wojciech.dubowik@neratec.com> + * Luka Perkov <uboot@lukaperkov.net> + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program. If not, see <http://www.gnu.org/licenses/>. + */ + +#ifndef __ICONNECT_H +#define __ICONNECT_H + +#define ICONNECT_OE_LOW (~(1 << 7)) +#define ICONNECT_OE_HIGH (~(1 << 10)) +#define ICONNECT_OE_VAL_LOW (0) +#define ICONNECT_OE_VAL_HIGH (1 << 10) + +/* PHY related */ +#define MV88E1116_LED_FCTRL_REG 10 +#define MV88E1116_CPRSP_CR3_REG 21 +#define MV88E1116_MAC_CTRL_REG 21 +#define MV88E1116_PGADR_REG 22 +#define MV88E1116_RGMII_TXTM_CTRL (1 << 4) +#define MV88E1116_RGMII_RXTM_CTRL (1 << 5) + +#endif /* __ICONNECT_H */ diff --git a/board/iomega/iconnect/kwbimage.cfg b/board/iomega/iconnect/kwbimage.cfg new file mode 100644 index 0000000..6c9dfe3 --- /dev/null +++ b/board/iomega/iconnect/kwbimage.cfg @@ -0,0 +1,165 @@ +# +# (C) Copyright 2009-2012 +# Wojciech Dubowik <wojciech.dubowik@neratec.com> +# Luka Perkov <uboot@lukaperkov.net> +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program. If not, see <http://www.gnu.org/licenses/>. +# +# Refer docs/README.kwimage for more details about how-to configure +# and create kirkwood boot image +# + +# Boot Media configurations +BOOT_FROM nand +NAND_ECC_MODE default +NAND_PAGE_SIZE 0x0800 + +# SOC registers configuration using bootrom header extension +# Maximum KWBIMAGE_MAX_CONFIG configurations allowed + +# Configure RGMII-0 interface pad voltage to 1.8V +DATA 0xffd100e0 0x1b1b1b9b + +#Dram initalization for SINGLE x16 CL=5 @ 400MHz +DATA 0xffd01400 0x43000c30 # DDR Configuration register +# bit13-0: 0xc30, (3120 DDR2 clks refresh rate) +# bit23-14: 0x0, +# bit24: 0x1, enable exit self refresh mode on DDR access +# bit25: 0x1, required +# bit29-26: 0x0, +# bit31-30: 0x1, + +DATA 0xffd01404 0x37543000 # DDR Controller Control Low +# bit4: 0x0, addr/cmd in smame cycle +# bit5: 0x0, clk is driven during self refresh, we don't care for APX +# bit6: 0x0, use recommended falling edge of clk for addr/cmd +# bit14: 0x0, input buffer always powered up +# bit18: 0x1, cpu lock transaction enabled +# bit23-20: 0x5, recommended value for CL=5 and STARTBURST_DEL disabled bit31=0 +# bit27-24: 0x7, CL+2, STARTBURST sample stages, for freqs 400MHz, unbuffered DIMM +# bit30-28: 0x3, required +# bit31: 0x0, no additional STARTBURST delay + +DATA 0xffd01408 0x22125451 # DDR Timing (Low) (active cycles value +1) +# bit3-0: TRAS lsbs +# bit7-4: TRCD +# bit11-8: TRP +# bit15-12: TWR +# bit19-16: TWTR +# bit20: TRAS msb +# bit23-21: 0x0 +# bit27-24: TRRD +# bit31-28: TRTP + +DATA 0xffd0140c 0x00000a33 # DDR Timing (High) +# bit6-0: TRFC +# bit8-7: TR2R +# bit10-9: TR2W +# bit12-11: TW2W +# bit31-13: 0x0, required + +DATA 0xffd01410 0x000000cc # DDR Address Control +# bit1-0: 00, Cs0width (x8) +# bit3-2: 11, Cs0size (1Gb) +# bit5-4: 00, Cs1width (x8) +# bit7-6: 11, Cs1size (1Gb) +# bit9-8: 00, Cs2width (nonexistent) +# bit11-10: 00, Cs2size (nonexistent) +# bit13-12: 00, Cs3width (nonexistent) +# bit15-14: 00, Cs3size (nonexistent) +# bit16: 0, Cs0AddrSel +# bit17: 0, Cs1AddrSel +# bit18: 0, Cs2AddrSel +# bit19: 0, Cs3AddrSel +# bit31-20: 0x0, required + +DATA 0xffd01414 0x00000000 # DDR Open Pages Control +# bit0: 0, OpenPage enabled +# bit31-1: 0x0, required + +DATA 0xffd01418 0x00000000 # DDR Operation +# bit3-0: 0x0, DDR cmd +# bit31-4: 0x0, required + +DATA 0xffd0141c 0x00000c52 # DDR Mode +# bit2-0: 0x2, BurstLen=2 required +# bit3: 0x0, BurstType=0 required +# bit6-4: 0x4, CL=5 +# bit7: 0x0, TestMode=0 normal +# bit8: 0x0, DLL reset=0 normal +# bit11-9: 0x6, auto-precharge write recovery ???????????? +# bit12: 0x0, PD must be zero +# bit31-13: 0x0, required + +DATA 0xffd01420 0x00000040 # DDR Extended Mode +# bit0: 0, DDR DLL enabled +# bit1: 0, DDR drive strenght normal +# bit2: 0, DDR ODT control lsd (disabled) +# bit5-3: 0x0, required +# bit6: 1, DDR ODT control msb, (disabled) +# bit9-7: 0x0, required +# bit10: 0, differential DQS enabled +# bit11: 0, required +# bit12: 0, DDR output buffer enabled +# bit31-13: 0x0, required + +DATA 0xffd01424 0x0000f17f # DDR Controller Control High +# bit2-0: 0x7, required +# bit3: 0x1, MBUS Burst Chop disabled +# bit6-4: 0x7, required +# bit7: 0x0, +# bit8: 0x1, add writepath sample stage, must be 1 for DDR freq >= 300MHz +# bit9: 0x0, no half clock cycle addition to dataout +# bit10: 0x0, 1/4 clock cycle skew enabled for addr/ctl signals +# bit11: 0x0, 1/4 clock cycle skew disabled for write mesh +# bit15-12: 0xf, required +# bit31-16: 0x0, required + +DATA 0xffd01428 0x00085520 # DDR2 ODT Read Timing (default values) +DATA 0xffd0147c 0x00008552 # DDR2 ODT Write Timing (default values) + +DATA 0xffd01500 0x00000000 # CS[0]n Base address to 0x0 +DATA 0xffd01504 0x0ffffff1 # CS[0]n Size +# bit0: 0x1, Window enabled +# bit1: 0x0, Write Protect disabled +# bit3-2: 0x0, CS0 hit selected +# bit23-4: 0xfffff, required +# bit31-24: 0x0f, Size (i.e. 256MB) + +DATA 0xffd01508 0x00000000 # CS[1]n Base address to 256Mb +DATA 0xffd0150c 0x00000000 # CS[1]n Size, window disabled + +DATA 0xffd01514 0x00000000 # CS[2]n Size, window disabled +DATA 0xffd0151c 0x00000000 # CS[3]n Size, window disabled + +DATA 0xffd01494 0x00030000 # DDR ODT Control (Low) +# bit3-0: ODT0Rd, MODT[0] asserted during read from DRAM CS1 +# bit7-4: ODT0Rd, MODT[0] asserted during read from DRAM CS0 +# bit19-16:2, ODT0Wr, MODT[0] asserted during write to DRAM CS1 +# bit23-20:1, ODT0Wr, MODT[0] asserted during write to DRAM CS0 + +DATA 0xffd01498 0x00000000 # DDR ODT Control (High) +# bit1-0: 0x0, ODT0 controlled by ODT Control (low) register above +# bit3-2: 0x1, ODT1 active NEVER! +# bit31-4: 0x0, required + +DATA 0xffd0149c 0x0000e803 # CPU ODT Control +DATA 0xffd01480 0x00000001 # DDR Initialization Control +# bit0: 0x1, enable DDR init upon this register write + +# End of Header extension +DATA 0x0 0x0 diff --git a/board/karo/tx25/lowlevel_init.S b/board/karo/tx25/lowlevel_init.S index 823df10..eb3f187 100644 --- a/board/karo/tx25/lowlevel_init.S +++ b/board/karo/tx25/lowlevel_init.S @@ -67,6 +67,14 @@ write32 0x53f80008, 0x20034000 /* + * PCDR2: NFC = 33.25 MHz + * This is required for the NAND Flash of this board, which is a Samsung + * K9F1G08U0B with 25-ns R/W cycle times, in order to make it work with + * the NFC driver in symmetric (i.e. one-cycle) mode. + */ + write32 0x53f80020, 0x01010103 + + /* * enable all implemented clocks in all three * clock control registers */ diff --git a/board/keymile/km_arm/km_arm.c b/board/keymile/km_arm/km_arm.c index be8f51c..0c4dddc 100644 --- a/board/keymile/km_arm/km_arm.c +++ b/board/keymile/km_arm/km_arm.c @@ -250,7 +250,8 @@ int board_early_init_f(void) tmp = readl(KW_GPIO0_BASE + 4); writel(tmp & (~KM_KIRKWOOD_SOFT_I2C_GPIOS) , KW_GPIO0_BASE + 4); #endif - + /* adjust SDRAM size for bank 0 */ + kw_sdram_size_adjust(0); kirkwood_mpp_conf(kwmpp_config, NULL); return 0; } @@ -365,6 +366,71 @@ void reset_phy(void) /* reset the phy */ miiphy_reset(name, CONFIG_PHY_BASE_ADR); } +#elif defined(CONFIG_KM_PIGGY4_88E6352) + +#include <mv88e6352.h> + +#if defined(CONFIG_KM_NUSA) +struct mv88e_sw_reg extsw_conf[] = { + /* + * port 0, PIGGY4, autoneg + * first the fix for the 1000Mbits Autoneg, this is from + * a Marvell errata, the regs are undocumented + */ + { PHY(0), PHY_PAGE, AN1000FIX_PAGE }, + { PHY(0), PHY_STATUS, AN1000FIX }, + { PHY(0), PHY_PAGE, 0 }, + /* now the real port and phy configuration */ + { PORT(0), PORT_PHY, NO_SPEED_FOR }, + { PORT(0), PORT_CTRL, FORWARDING | EGRS_FLD_ALL }, + { PHY(0), PHY_1000_CTRL, NO_ADV }, + { PHY(0), PHY_SPEC_CTRL, AUTO_MDIX_EN }, + { PHY(0), PHY_CTRL, PHY_100_MBPS | AUTONEG_EN | AUTONEG_RST | + FULL_DUPLEX }, + /* port 1, unused */ + { PORT(1), PORT_CTRL, PORT_DIS }, + { PHY(1), PHY_CTRL, PHY_PWR_DOWN }, + { PHY(1), PHY_SPEC_CTRL, SPEC_PWR_DOWN }, + /* port 2, unused */ + { PORT(2), PORT_CTRL, PORT_DIS }, + { PHY(2), PHY_CTRL, PHY_PWR_DOWN }, + { PHY(2), PHY_SPEC_CTRL, SPEC_PWR_DOWN }, + /* port 3, unused */ + { PORT(3), PORT_CTRL, PORT_DIS }, + { PHY(3), PHY_CTRL, PHY_PWR_DOWN }, + { PHY(3), PHY_SPEC_CTRL, SPEC_PWR_DOWN }, + /* port 4, ICNEV, SerDes, SGMII */ + { PORT(4), PORT_STATUS, NO_PHY_DETECT }, + { PORT(4), PORT_PHY, SPEED_1000_FOR }, + { PORT(4), PORT_CTRL, FORWARDING | EGRS_FLD_ALL }, + { PHY(4), PHY_CTRL, PHY_PWR_DOWN }, + { PHY(4), PHY_SPEC_CTRL, SPEC_PWR_DOWN }, + /* port 5, CPU_RGMII */ + { PORT(5), PORT_PHY, RX_RGMII_TIM | TX_RGMII_TIM | FLOW_CTRL_EN | + FLOW_CTRL_FOR | LINK_VAL | LINK_FOR | FULL_DPX | + FULL_DPX_FOR | SPEED_1000_FOR }, + { PORT(5), PORT_CTRL, FORWARDING | EGRS_FLD_ALL }, + /* port 6, unused, this port has no phy */ + { PORT(6), PORT_CTRL, PORT_DIS }, +}; +#else +struct mv88e_sw_reg extsw_conf[] = {}; +#endif + +void reset_phy(void) +{ +#if defined(CONFIG_KM_MVEXTSW_ADDR) + char *name = "egiga0"; + + if (miiphy_set_current_dev(name)) + return; + + mv88e_sw_program(name, CONFIG_KM_MVEXTSW_ADDR, extsw_conf, + ARRAY_SIZE(extsw_conf)); + mv88e_sw_reset(name, CONFIG_KM_MVEXTSW_ADDR); +#endif +} + #else /* Configure and enable MV88E1118 PHY on the piggy*/ void reset_phy(void) diff --git a/board/kmc/kzm9g/Makefile b/board/kmc/kzm9g/Makefile new file mode 100644 index 0000000..bae79f5 --- /dev/null +++ b/board/kmc/kzm9g/Makefile @@ -0,0 +1,50 @@ +# +# (C) Copyright 2012 Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> +# (C) Copyright 2012 Renesas Solutions Corp. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +include $(TOPDIR)/config.mk + +LIB = $(obj)lib$(BOARD).o + +COBJS := kzm9g.o + +SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS)) +SOBJS := $(addprefix $(obj),$(SOBJS)) + +$(LIB): $(obj).depend $(OBJS) $(SOBJS) + $(call cmd_link_o_target, $(OBJS) $(SOBJS)) + +clean: + rm -f $(SOBJS) $(OBJS) + +distclean: clean + rm -f $(LIB) core *.bak $(obj) .depend + +######################################################################### + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################### diff --git a/board/kmc/kzm9g/kzm9g.c b/board/kmc/kzm9g/kzm9g.c new file mode 100644 index 0000000..525c97a --- /dev/null +++ b/board/kmc/kzm9g/kzm9g.c @@ -0,0 +1,377 @@ +/* + * (C) Copyright 2012 Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> + * (C) Copyright 2012 Renesas Solutions Corp. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <common.h> +#include <asm/io.h> +#include <asm/arch/sys_proto.h> +#include <asm/gpio.h> +#include <netdev.h> +#include <i2c.h> + +DECLARE_GLOBAL_DATA_PTR; + +#define CS0BCR_D (0x06C00400) +#define CS4BCR_D (0x16c90400) +#define CS0WCR_D (0x55062C42) +#define CS4WCR_D (0x1e071dc3) + +#define CMNCR_BROMMD0 (1 << 21) +#define CMNCR_BROMMD1 (1 << 22) +#define CMNCR_BROMMD (CMNCR_BROMMD0|CMNCR_BROMMD1) +#define VCLKCR1_D (0x27) + +#define SMSTPCR1_CMT0 (1 << 24) +#define SMSTPCR1_I2C0 (1 << 16) +#define SMSTPCR3_USB (1 << 22) + +#define PORT32CR (0xE6051020) +#define PORT33CR (0xE6051021) +#define PORT34CR (0xE6051022) +#define PORT35CR (0xE6051023) + +static int cmp_loop(u32 *addr, u32 data, u32 cmp) +{ + int err = -1; + int timeout = 100; + u32 value; + + while (timeout > 0) { + value = readl(addr); + if ((value & data) == cmp) { + err = 0; + break; + } + timeout--; + } + + return err; +} + +/* SBSC Init function */ +static void sbsc_init(struct sh73a0_sbsc *sbsc) +{ + writel(readl(&sbsc->dllcnt0)|0x2, &sbsc->dllcnt0); + writel(0x5, &sbsc->sdgencnt); + cmp_loop(&sbsc->sdgencnt, 0xffffffff, 0x0); + + writel(0xacc90159, &sbsc->sdcr0); + writel(0x00010059, &sbsc->sdcr1); + writel(0x50874114, &sbsc->sdwcrc0); + writel(0x33199b37, &sbsc->sdwcrc1); + writel(0x008f2313, &sbsc->sdwcrc2); + writel(0x31020707, &sbsc->sdwcr00); + writel(0x0017040a, &sbsc->sdwcr01); + writel(0x31020707, &sbsc->sdwcr10); + writel(0x0017040a, &sbsc->sdwcr11); + writel(0x05555555, &sbsc->sddrvcr0); + writel(0x30000000, &sbsc->sdwcr2); + + writel(readl(&sbsc->sdpcr) | 0x80, &sbsc->sdpcr); + cmp_loop(&sbsc->sdpcr, 0x80, 0x80); + + writel(0x00002710, &sbsc->sdgencnt); + cmp_loop(&sbsc->sdgencnt, 0xffffffff, 0x0); + + writel(0x0000003f, &sbsc->sdmracr0); + writel(0x0, SDMRA1A); + writel(0x000001f4, &sbsc->sdgencnt); + cmp_loop(&sbsc->sdgencnt, 0xffffffff, 0x0); + + writel(0x0000ff0a, &sbsc->sdmracr0); + if (sbsc == (struct sh73a0_sbsc *)SBSC1_BASE) + writel(0x0, SDMRA3A); + else + writel(0x0, SDMRA3B); + + writel(0x00000032, &sbsc->sdgencnt); + cmp_loop(&sbsc->sdgencnt, 0xffffffff, 0x0); + + if (sbsc == (struct sh73a0_sbsc *)SBSC1_BASE) { + writel(0x00002201, &sbsc->sdmracr0); + writel(0x0, SDMRA1A); + writel(0x00000402, &sbsc->sdmracr0); + writel(0x0, SDMRA1A); + writel(0x00000403, &sbsc->sdmracr0); + writel(0x0, SDMRA1A); + writel(0x0, SDMRA2A); + } else { + writel(0x00002201, &sbsc->sdmracr0); + writel(0x0, SDMRA1B); + writel(0x00000402, &sbsc->sdmracr0); + writel(0x0, SDMRA1B); + writel(0x00000403, &sbsc->sdmracr0); + writel(0x0, SDMRA1B); + writel(0x0, SDMRA2B); + } + + writel(0x88800004, &sbsc->sdmrtmpcr); + writel(0x00000004, &sbsc->sdmrtmpmsk); + writel(0xa55a0032, &sbsc->rtcor); + writel(0xa55a000c, &sbsc->rtcorh); + writel(0xa55a2048, &sbsc->rtcsr); + writel(readl(&sbsc->sdcr0)|0x800, &sbsc->sdcr0); + writel(readl(&sbsc->sdcr1)|0x400, &sbsc->sdcr1); + writel(0xfff20000, &sbsc->zqccr); + + /* SCBS2 only */ + if (sbsc == (struct sh73a0_sbsc *)SBSC2_BASE) { + writel(readl(&sbsc->sdpdcr0)|0x00030000, &sbsc->sdpdcr0); + writel(0xa5390000, &sbsc->dphycnt1); + writel(0x00001200, &sbsc->dphycnt0); + writel(0x07ce0000, &sbsc->dphycnt1); + writel(0x00001247, &sbsc->dphycnt0); + cmp_loop(&sbsc->dphycnt2, 0xffffffff, 0x07ce0000); + writel(readl(&sbsc->sdpdcr0) & 0xfffcffff, &sbsc->sdpdcr0); + } +} + +void s_init(void) +{ + struct sh73a0_rwdt *rwdt = (struct sh73a0_rwdt *)RWDT_BASE; + struct sh73a0_sbsc_cpg *cpg = (struct sh73a0_sbsc_cpg *)CPG_BASE; + struct sh73a0_sbsc_cpg_srcr *cpg_srcr = + (struct sh73a0_sbsc_cpg_srcr *)CPG_SRCR_BASE; + struct sh73a0_sbsc *sbsc1 = (struct sh73a0_sbsc *)SBSC1_BASE; + struct sh73a0_sbsc *sbsc2 = (struct sh73a0_sbsc *)SBSC2_BASE; + struct sh73a0_hpb *hpb = (struct sh73a0_hpb *)HPB_BASE; + struct sh73a0_hpb_bscr *hpb_bscr = + (struct sh73a0_hpb_bscr *)HPBSCR_BASE; + + /* Watchdog init */ + writew(0xA507, &rwdt->rwtcsra0); + + /* Secure control register Init */ + #define LIFEC_SEC_SRC_BIT (1 << 15) + writel(readl(LIFEC_SEC_SRC) & ~LIFEC_SEC_SRC_BIT, LIFEC_SEC_SRC); + + clrbits_le32(&cpg->smstpcr3, (1 << 15)); + clrbits_le32(&cpg_srcr->srcr3, (1 << 15)); + clrbits_le32(&cpg->smstpcr2, (1 << 18)); + clrbits_le32(&cpg_srcr->srcr2, (1 << 18)); + writel(0x0, &cpg->pllecr); + + cmp_loop(&cpg->pllecr, 0x00000F00, 0x0); + cmp_loop(&cpg->frqcrb, 0x80000000, 0x0); + + writel(0x2D000000, &cpg->pll0cr); + writel(0x17100000, &cpg->pll1cr); + writel(0x96235880, &cpg->frqcrb); + cmp_loop(&cpg->frqcrb, 0x80000000, 0x0); + + writel(0xB, &cpg->flckcr); + clrbits_le32(&cpg->smstpcr0, (1 << 1)); + + clrbits_le32(&cpg_srcr->srcr0, (1 << 1)); + writel(0x0514, &hpb_bscr->smgpiotime); + writel(0x0514, &hpb_bscr->smcmt2time); + writel(0x0514, &hpb_bscr->smcpgtime); + writel(0x0514, &hpb_bscr->smsysctime); + + writel(0x00092000, &cpg->dvfscr4); + writel(0x000000DC, &cpg->dvfscr5); + writel(0x0, &cpg->pllecr); + cmp_loop(&cpg->pllecr, 0x00000F00, 0x0); + + /* FRQCR Init */ + writel(0x0012453C, &cpg->frqcra); + writel(0x80331350, &cpg->frqcrb); + cmp_loop(&cpg->frqcrb, 0x80000000, 0x0); + writel(0x00000B0B, &cpg->frqcrd); + cmp_loop(&cpg->frqcrd, 0x80000000, 0x0); + + /* Clock Init */ + writel(0x00000003, PCLKCR); + writel(0x0000012F, &cpg->vclkcr1); + writel(0x00000119, &cpg->vclkcr2); + writel(0x00000119, &cpg->vclkcr3); + writel(0x00000002, &cpg->zbckcr); + writel(0x00000005, &cpg->flckcr); + writel(0x00000080, &cpg->sd0ckcr); + writel(0x00000080, &cpg->sd1ckcr); + writel(0x00000080, &cpg->sd2ckcr); + writel(0x0000003F, &cpg->fsiackcr); + writel(0x0000003F, &cpg->fsibckcr); + writel(0x00000080, &cpg->subckcr); + writel(0x0000000B, &cpg->spuackcr); + writel(0x0000000B, &cpg->spuvckcr); + writel(0x0000013F, &cpg->msuckcr); + writel(0x00000080, &cpg->hsickcr); + writel(0x0000003F, &cpg->mfck1cr); + writel(0x0000003F, &cpg->mfck2cr); + writel(0x00000107, &cpg->dsitckcr); + writel(0x00000313, &cpg->dsi0pckcr); + writel(0x0000130D, &cpg->dsi1pckcr); + writel(0x2A800E0E, &cpg->dsi0phycr); + writel(0x1E000000, &cpg->pll0cr); + writel(0x2D000000, &cpg->pll0cr); + writel(0x17100000, &cpg->pll1cr); + writel(0x27000080, &cpg->pll2cr); + writel(0x1D000000, &cpg->pll3cr); + writel(0x00080000, &cpg->pll0stpcr); + writel(0x000120C0, &cpg->pll1stpcr); + writel(0x00012000, &cpg->pll2stpcr); + writel(0x00000030, &cpg->pll3stpcr); + + writel(0x0000000B, &cpg->pllecr); + cmp_loop(&cpg->pllecr, 0x00000B00, 0x00000B00); + + writel(0x000120F0, &cpg->dvfscr3); + writel(0x00000020, &cpg->mpmode); + writel(0x0000028A, &cpg->vrefcr); + writel(0xE4628087, &cpg->rmstpcr0); + writel(0xFFFFFFFF, &cpg->rmstpcr1); + writel(0x53FFFFFF, &cpg->rmstpcr2); + writel(0xFFFFFFFF, &cpg->rmstpcr3); + writel(0x00800D3D, &cpg->rmstpcr4); + writel(0xFFFFF3FF, &cpg->rmstpcr5); + writel(0x00000000, &cpg->smstpcr2); + writel(0x00040000, &cpg_srcr->srcr2); + + clrbits_le32(&cpg->pllecr, (1 << 3)); + cmp_loop(&cpg->pllecr, 0x00000800, 0x0); + + writel(0x00000001, &hpb->hpbctrl6); + cmp_loop(&hpb->hpbctrl6, 0x1, 0x1); + + writel(0x00001414, &cpg->frqcrd); + cmp_loop(&cpg->frqcrd, 0x80000000, 0x0); + + writel(0x1d000000, &cpg->pll3cr); + setbits_le32(&cpg->pllecr, (1 << 3)); + cmp_loop(&cpg->pllecr, 0x800, 0x800); + + /* SBSC1 Init*/ + sbsc_init(sbsc1); + + /* SBSC2 Init*/ + sbsc_init(sbsc2); + + writel(0x00000b0b, &cpg->frqcrd); + cmp_loop(&cpg->frqcrd, 0x80000000, 0x0); + writel(0xfffffffc, &cpg->cpgxxcs4); +} + +int board_early_init_f(void) +{ + struct sh73a0_sbsc_cpg *cpg = (struct sh73a0_sbsc_cpg *)CPG_BASE; + struct sh73a0_bsc *bsc = (struct sh73a0_bsc *)BSC_BASE; + struct sh73a0_sbsc_cpg_srcr *cpg_srcr = + (struct sh73a0_sbsc_cpg_srcr *)CPG_SRCR_BASE; + + writel(CS0BCR_D, &bsc->cs0bcr); + writel(CS4BCR_D, &bsc->cs4bcr); + writel(CS0WCR_D, &bsc->cs0wcr); + writel(CS4WCR_D, &bsc->cs4wcr); + + clrsetbits_le32(&bsc->cmncr, ~CMNCR_BROMMD, CMNCR_BROMMD); + + clrbits_le32(&cpg->smstpcr1, (SMSTPCR1_CMT0|SMSTPCR1_I2C0)); + clrbits_le32(&cpg_srcr->srcr1, (SMSTPCR1_CMT0|SMSTPCR1_I2C0)); + clrbits_le32(&cpg->smstpcr3, SMSTPCR3_USB); + clrbits_le32(&cpg_srcr->srcr3, SMSTPCR3_USB); + writel(VCLKCR1_D, &cpg->vclkcr1); + + /* Setup SCIF4 / workaround */ + writeb(0x12, PORT32CR); + writeb(0x22, PORT33CR); + writeb(0x12, PORT34CR); + writeb(0x22, PORT35CR); + + return 0; +} + +int board_init(void) +{ + sh73a0_pinmux_init(); + + /* SCIFA 4 */ + gpio_request(GPIO_FN_SCIFA4_TXD, NULL); + gpio_request(GPIO_FN_SCIFA4_RXD, NULL); + gpio_request(GPIO_FN_SCIFA4_RTS_, NULL); + gpio_request(GPIO_FN_SCIFA4_CTS_, NULL); + + /* Ethernet/SMSC */ + gpio_request(GPIO_PORT224, NULL); + gpio_direction_input(GPIO_PORT224); + + /* SMSC/USB */ + gpio_request(GPIO_FN_CS4_, NULL); + + /* MMCIF */ + gpio_request(GPIO_FN_MMCCLK0, NULL); + gpio_request(GPIO_FN_MMCCMD0_PU, NULL); + gpio_request(GPIO_FN_MMCD0_0_PU, NULL); + gpio_request(GPIO_FN_MMCD0_1_PU, NULL); + gpio_request(GPIO_FN_MMCD0_2_PU, NULL); + gpio_request(GPIO_FN_MMCD0_3_PU, NULL); + gpio_request(GPIO_FN_MMCD0_4_PU, NULL); + gpio_request(GPIO_FN_MMCD0_5_PU, NULL); + gpio_request(GPIO_FN_MMCD0_6_PU, NULL); + gpio_request(GPIO_FN_MMCD0_7_PU, NULL); + + /* SDHI */ + gpio_request(GPIO_FN_SDHIWP0, NULL); + gpio_request(GPIO_FN_SDHICD0, NULL); + gpio_request(GPIO_FN_SDHICMD0, NULL); + gpio_request(GPIO_FN_SDHICLK0, NULL); + gpio_request(GPIO_FN_SDHID0_3, NULL); + gpio_request(GPIO_FN_SDHID0_2, NULL); + gpio_request(GPIO_FN_SDHID0_1, NULL); + gpio_request(GPIO_FN_SDHID0_0, NULL); + gpio_request(GPIO_FN_SDHI0_VCCQ_MC0_ON, NULL); + gpio_request(GPIO_PORT15, NULL); + gpio_direction_output(GPIO_PORT15, 1); + + /* I2C */ + gpio_request(GPIO_FN_PORT27_I2C_SCL3, NULL); + gpio_request(GPIO_FN_PORT28_I2C_SDA3, NULL); + + gd->bd->bi_boot_params = (CONFIG_SYS_SDRAM_BASE + 0x100); + + return 0; +} + +const struct rmobile_sysinfo sysinfo = { + CONFIG_RMOBILE_BOARD_STRING +}; + +int dram_init(void) +{ + gd->ram_size = CONFIG_SYS_SDRAM_SIZE; + return 0; +} + +int board_eth_init(bd_t *bis) +{ + int ret = 0; +#ifdef CONFIG_SMC911X + ret = smc911x_initialize(0, CONFIG_SMC911X_BASE); +#endif + return ret; +} + +void reset_cpu(ulong addr) +{ + /* Soft Power On Reset */ + writel((1 << 31), RESCNT2); +} diff --git a/board/raidsonic/ib62x0/ib62x0.c b/board/raidsonic/ib62x0/ib62x0.c index 1164d6b..b7e6e41 100644 --- a/board/raidsonic/ib62x0/ib62x0.c +++ b/board/raidsonic/ib62x0/ib62x0.c @@ -23,6 +23,7 @@ #include <common.h> #include <miiphy.h> +#include <asm/io.h> #include <asm/arch/cpu.h> #include <asm/arch/kirkwood.h> #include <asm/arch/mpp.h> @@ -41,6 +42,8 @@ int board_early_init_f(void) IB62x0_OE_VAL_HIGH, IB62x0_OE_LOW, IB62x0_OE_HIGH); + /* Set SATA activity LEDs to default off */ + writel(MVSATAHC_LED_POLARITY_CTRL, MVSATAHC_LED_CONF_REG); /* Multi-Purpose Pins Functionality configuration */ u32 kwmpp_config[] = { MPP0_NF_IO2, diff --git a/board/raidsonic/ib62x0/ib62x0.h b/board/raidsonic/ib62x0/ib62x0.h index 0c30690..0118c2b 100644 --- a/board/raidsonic/ib62x0/ib62x0.h +++ b/board/raidsonic/ib62x0/ib62x0.h @@ -37,4 +37,8 @@ #define MV88E1116_RGMII_TXTM_CTRL (1 << 4) #define MV88E1116_RGMII_RXTM_CTRL (1 << 5) +/* SATAHC related */ +#define MVSATAHC_LED_CONF_REG (MV_SATA_BASE + 0x2C) +#define MVSATAHC_LED_POLARITY_CTRL (1 << 3) + #endif /* __IB62x0_H */ diff --git a/board/spear/x600/Makefile b/board/spear/x600/Makefile new file mode 100644 index 0000000..8c4e7e2 --- /dev/null +++ b/board/spear/x600/Makefile @@ -0,0 +1,47 @@ +# +# (C) Copyright 2000-2004 +# Wolfgang Denk, DENX Software Engineering, wd@denx.de. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +include $(TOPDIR)/config.mk + +LIB = $(obj)lib$(BOARD).o + +ifndef CONFIG_SPL_BUILD +COBJS := fpga.o $(BOARD).o +endif +SOBJS := + +SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS)) +SOBJS := $(addprefix $(obj),$(SOBJS)) + +$(LIB): $(obj).depend $(OBJS) $(SOBJS) + $(call cmd_link_o_target, $(OBJS) $(SOBJS)) + +######################################################################### + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################### diff --git a/board/spear/x600/fpga.c b/board/spear/x600/fpga.c new file mode 100644 index 0000000..85eb31b --- /dev/null +++ b/board/spear/x600/fpga.c @@ -0,0 +1,280 @@ +/* + * Copyright (C) 2012 Stefan Roese <sr@denx.de> + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <common.h> +#include <spartan3.h> +#include <command.h> +#include <asm/gpio.h> +#include <asm/io.h> +#include <asm/arch/hardware.h> +#include <asm/arch/spr_misc.h> +#include <asm/arch/spr_ssp.h> + +/* + * FPGA program pin configuration on X600: + * + * Only PROG and DONE are connected to GPIOs. INIT is not connected to the + * SoC at all. And CLOCK and DATA are connected to the SSP2 port. We use + * 16bit serial writes via this SSP port to write the data bits into the + * FPGA. + */ +#define CONFIG_SYS_FPGA_PROG 2 +#define CONFIG_SYS_FPGA_DONE 3 + +/* + * Set the active-low FPGA reset signal. + */ +static void fpga_reset(int assert) +{ + /* + * On x600 we have no means to toggle the FPGA reset signal + */ + debug("%s:%d: RESET (%d)\n", __func__, __LINE__, assert); +} + +/* + * Set the FPGA's active-low SelectMap program line to the specified level + */ +static int fpga_pgm_fn(int assert, int flush, int cookie) +{ + debug("%s:%d: FPGA PROG (%d)\n", __func__, __LINE__, assert); + + gpio_set_value(CONFIG_SYS_FPGA_PROG, assert); + + return assert; +} + +/* + * Test the state of the active-low FPGA INIT line. Return 1 on INIT + * asserted (low). + */ +static int fpga_init_fn(int cookie) +{ + static int state; + + debug("%s:%d: init (state=%d)\n", __func__, __LINE__, state); + + /* + * On x600, the FPGA INIT signal is not connected to the SoC. + * We can't read the INIT status. Let's return the "correct" + * INIT signal state generated via a local state-machine. + */ + if (++state == 1) { + return 1; + } else { + state = 0; + return 0; + } +} + +/* + * Test the state of the active-high FPGA DONE pin + */ +static int fpga_done_fn(int cookie) +{ + struct ssp_regs *ssp = (struct ssp_regs *)CONFIG_SSP2_BASE; + + /* + * Wait for Tx-FIFO to become empty before looking for DONE + */ + while (!(readl(&ssp->sspsr) & SSPSR_TFE)) + ; + + if (gpio_get_value(CONFIG_SYS_FPGA_DONE)) + return 1; + else + return 0; +} + +/* + * FPGA pre-configuration function. Just make sure that + * FPGA reset is asserted to keep the FPGA from starting up after + * configuration. + */ +static int fpga_pre_config_fn(int cookie) +{ + debug("%s:%d: FPGA pre-configuration\n", __func__, __LINE__); + fpga_reset(TRUE); + + return 0; +} + +/* + * FPGA post configuration function. Blip the FPGA reset line and then see if + * the FPGA appears to be running. + */ +static int fpga_post_config_fn(int cookie) +{ + int rc = 0; + + debug("%s:%d: FPGA post configuration\n", __func__, __LINE__); + + fpga_reset(TRUE); + udelay(100); + fpga_reset(FALSE); + udelay(100); + + return rc; +} + +static int fpga_clk_fn(int assert_clk, int flush, int cookie) +{ + /* + * No dedicated clock signal on x600 (data & clock generated) + * in SSP interface. So we don't have to do anything here. + */ + return assert_clk; +} + +static int fpga_wr_fn(int assert_write, int flush, int cookie) +{ + struct ssp_regs *ssp = (struct ssp_regs *)CONFIG_SSP2_BASE; + static int count; + static u16 data; + + /* + * First collect 16 bits of data + */ + data = data << 1; + if (assert_write) + data |= 1; + + /* + * If 16 bits are not available, return for more bits + */ + count++; + if (count != 16) + return assert_write; + + count = 0; + + /* + * Wait for Tx-FIFO to become ready + */ + while (!(readl(&ssp->sspsr) & SSPSR_TNF)) + ; + + /* Send 16 bits to FPGA via SSP bus */ + writel(data, &ssp->sspdr); + + return assert_write; +} + +static Xilinx_Spartan3_Slave_Serial_fns x600_fpga_fns = { + fpga_pre_config_fn, + fpga_pgm_fn, + fpga_clk_fn, + fpga_init_fn, + fpga_done_fn, + fpga_wr_fn, + fpga_post_config_fn, +}; + +static Xilinx_desc fpga[CONFIG_FPGA_COUNT] = { + XILINX_XC3S1200E_DESC(slave_serial, &x600_fpga_fns, 0) +}; + +/* + * Initialize the SelectMap interface. We assume that the mode and the + * initial state of all of the port pins have already been set! + */ +static void fpga_serialslave_init(void) +{ + debug("%s:%d: Initialize serial slave interface\n", __func__, __LINE__); + fpga_pgm_fn(FALSE, FALSE, 0); /* make sure program pin is inactive */ +} + +static int expi_setup(int freq) +{ + struct misc_regs *misc = (struct misc_regs *)CONFIG_SPEAR_MISCBASE; + int pll2_m, pll2_n, pll2_p, expi_x, expi_y; + + pll2_m = (freq * 2) / 1000; + pll2_n = 15; + pll2_p = 1; + expi_x = 1; + expi_y = 2; + + /* + * Disable reset, Low compression, Disable retiming, Enable Expi, + * Enable soft reset, DMA, PLL2, Internal + */ + writel(EXPI_CLK_CFG_LOW_COMPR | EXPI_CLK_CFG_CLK_EN | EXPI_CLK_CFG_RST | + EXPI_CLK_SYNT_EN | EXPI_CLK_CFG_SEL_PLL2 | + EXPI_CLK_CFG_INT_CLK_EN | (expi_y << 16) | (expi_x << 24), + &misc->expi_clk_cfg); + + /* + * 6 uA, Internal feedback, 1st order, Non-dithered, Sample Parameters, + * Enable PLL2, Disable reset + */ + writel((pll2_m << 24) | (pll2_p << 8) | (pll2_n), &misc->pll2_frq); + writel(PLL2_CNTL_6UA | PLL2_CNTL_SAMPLE | PLL2_CNTL_ENABLE | + PLL2_CNTL_RESETN | PLL2_CNTL_LOCK, &misc->pll2_cntl); + + /* + * Disable soft reset + */ + clrbits_le32(&misc->expi_clk_cfg, EXPI_CLK_CFG_RST); + + return 0; +} + +/* + * Initialize the fpga + */ +int x600_init_fpga(void) +{ + struct ssp_regs *ssp = (struct ssp_regs *)CONFIG_SSP2_BASE; + struct misc_regs *misc = (struct misc_regs *)CONFIG_SPEAR_MISCBASE; + + /* Enable SSP2 clock */ + writel(readl(&misc->periph1_clken) | MISC_SSP2ENB | MISC_GPIO4ENB, + &misc->periph1_clken); + + /* Set EXPI clock to 45 MHz */ + expi_setup(45000); + + /* Configure GPIO directions */ + gpio_direction_output(CONFIG_SYS_FPGA_PROG, 0); + gpio_direction_input(CONFIG_SYS_FPGA_DONE); + + writel(SSPCR0_DSS_16BITS, &ssp->sspcr0); + writel(SSPCR1_SSE, &ssp->sspcr1); + + /* + * Set lowest prescale divisor value (CPSDVSR) of 2 for max download + * speed. + * + * Actual data clock rate is: 80MHz / (CPSDVSR * (SCR + 1)) + * With CPSDVSR at 2 and SCR at 0, the maximume clock rate is 40MHz. + */ + writel(2, &ssp->sspcpsr); + + fpga_init(); + fpga_serialslave_init(); + + debug("%s:%d: Adding fpga 0\n", __func__, __LINE__); + fpga_add(fpga_xilinx, &fpga[0]); + + return 0; +} diff --git a/board/spear/x600/fpga.h b/board/spear/x600/fpga.h new file mode 100644 index 0000000..2b18557 --- /dev/null +++ b/board/spear/x600/fpga.h @@ -0,0 +1,23 @@ +/* + * Copyright (C) 2012 Stefan Roese <sr@denx.de> + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +int x600_init_fpga(void); diff --git a/board/spear/x600/x600.c b/board/spear/x600/x600.c new file mode 100644 index 0000000..96ec0ad --- /dev/null +++ b/board/spear/x600/x600.c @@ -0,0 +1,124 @@ +/* + * (C) Copyright 2009 + * Vipin Kumar, ST Micoelectronics, vipin.kumar@st.com. + * + * Copyright (C) 2012 Stefan Roese <sr@denx.de> + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <common.h> +#include <nand.h> +#include <netdev.h> +#include <phy.h> +#include <rtc.h> +#include <asm/io.h> +#include <asm/arch/hardware.h> +#include <asm/arch/spr_defs.h> +#include <asm/arch/spr_misc.h> +#include <linux/mtd/fsmc_nand.h> +#include "fpga.h" + +static struct nand_chip nand_chip[CONFIG_SYS_MAX_NAND_DEVICE]; + +int board_init(void) +{ + /* + * X600 is equipped with an M41T82 RTC. This RTC has the + * HT bit (Halt Update), which needs to be cleared upon + * power-up. Otherwise the RTC is halted. + */ + rtc_reset(); + + return spear_board_init(MACH_TYPE_SPEAR600); +} + +int board_late_init(void) +{ + /* + * Monitor and env protection on by default + */ + flash_protect(FLAG_PROTECT_SET, + CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE + + CONFIG_SYS_SPL_LEN + CONFIG_SYS_MONITOR_LEN + + 2 * CONFIG_ENV_SECT_SIZE - 1, + &flash_info[0]); + + /* Init FPGA subsystem */ + x600_init_fpga(); + + return 0; +} + +/* + * board_nand_init - Board specific NAND initialization + * @nand: mtd private chip structure + * + * Called by nand_init_chip to initialize the board specific functions + */ + +void board_nand_init(void) +{ + struct misc_regs *const misc_regs_p = + (struct misc_regs *)CONFIG_SPEAR_MISCBASE; + struct nand_chip *nand = &nand_chip[0]; + + if (!(readl(&misc_regs_p->auto_cfg_reg) & MISC_NANDDIS)) + fsmc_nand_init(nand); +} + +int designware_board_phy_init(struct eth_device *dev, int phy_addr, + int (*mii_write)(struct eth_device *, u8, u8, u16), + int dw_reset_phy(struct eth_device *)) +{ + /* Extended PHY control 1, select GMII */ + mii_write(dev, phy_addr, 23, 0x0020); + + /* Software reset necessary after GMII mode selction */ + dw_reset_phy(dev); + + /* Enable extended page register access */ + mii_write(dev, phy_addr, 31, 0x0001); + + /* 17e: Enhanced LED behavior, needs to be written twice */ + mii_write(dev, phy_addr, 17, 0x09ff); + mii_write(dev, phy_addr, 17, 0x09ff); + + /* 16e: Enhanced LED method select */ + mii_write(dev, phy_addr, 16, 0xe0ea); + + /* Disable extended page register access */ + mii_write(dev, phy_addr, 31, 0x0000); + + /* Enable clock output pin */ + mii_write(dev, phy_addr, 18, 0x0049); + + return 0; +} + +int board_eth_init(bd_t *bis) +{ + int ret = 0; + + if (designware_initialize(0, CONFIG_SPEAR_ETHBASE, CONFIG_PHY_ADDR, + PHY_INTERFACE_MODE_GMII) >= 0) + ret++; + + return ret; +} diff --git a/board/st-ericsson/snowball/snowball.c b/board/st-ericsson/snowball/snowball.c index 8c743c0..e750df1 100644 --- a/board/st-ericsson/snowball/snowball.c +++ b/board/st-ericsson/snowball/snowball.c @@ -253,6 +253,10 @@ int board_late_init(void) if ((raise_ab8500_gpio16() < 0)) printf("error: cant' raise GPIO16\n"); + /* empty UART RX FIFO */ + while (tstc()) + (void) getc(); + return 0; } diff --git a/board/ti/beagle/beagle.c b/board/ti/beagle/beagle.c index 99f833f..4954475 100644 --- a/board/ti/beagle/beagle.c +++ b/board/ti/beagle/beagle.c @@ -488,7 +488,7 @@ int board_mmc_init(bd_t *bis) } #endif -#ifdef CONFIG_USB_EHCI +#if defined(CONFIG_USB_EHCI) && !defined(CONFIG_SPL_BUILD) /* Call usb_stop() before starting the kernel */ void show_boot_progress(int val) { diff --git a/board/xilinx/zynq/Makefile b/board/xilinx/zynq/Makefile new file mode 100644 index 0000000..ef4faa1 --- /dev/null +++ b/board/xilinx/zynq/Makefile @@ -0,0 +1,54 @@ +# +# (C) Copyright 2000-2006 +# Wolfgang Denk, DENX Software Engineering, wd@denx.de. +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +include $(TOPDIR)/config.mk +ifneq ($(OBJTREE),$(SRCTREE)) +$(shell mkdir -p $(obj)../common) +endif + +LIB = $(obj)lib$(BOARD).o + +COBJS-y := board.o + +COBJS := $(sort $(COBJS-y)) + +SRCS := $(COBJS:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS)) + +$(LIB): $(obj).depend $(OBJS) + $(call cmd_link_o_target, $(OBJS)) + +clean: + rm -f $(OBJS) + +distclean: clean + rm -f $(LIB) core *.bak $(obj).depend + +######################################################################### + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################### diff --git a/board/xilinx/zynq/board.c b/board/xilinx/zynq/board.c new file mode 100644 index 0000000..8ed75c3 --- /dev/null +++ b/board/xilinx/zynq/board.c @@ -0,0 +1,54 @@ +/* + * (C) Copyright 2012 Michal Simek <monstr@monstr.eu> + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <common.h> +#include <netdev.h> + +DECLARE_GLOBAL_DATA_PTR; + +int board_init(void) +{ + icache_enable(); + + return 0; +} + + +#ifdef CONFIG_CMD_NET +int board_eth_init(bd_t *bis) +{ + u32 ret = 0; + +#if defined(CONFIG_ZYNQ_GEM) && defined(CONFIG_ZYNQ_GEM_BASEADDR0) + ret = zynq_gem_initialize(bis, CONFIG_ZYNQ_GEM_BASEADDR0); +#endif + + return ret; +} +#endif + +int dram_init(void) +{ + gd->ram_size = CONFIG_SYS_SDRAM_SIZE; + + return 0; +} |