summaryrefslogtreecommitdiff
path: root/board/idmr/idmr.c
diff options
context:
space:
mode:
Diffstat (limited to 'board/idmr/idmr.c')
-rw-r--r--board/idmr/idmr.c169
1 files changed, 169 insertions, 0 deletions
diff --git a/board/idmr/idmr.c b/board/idmr/idmr.c
new file mode 100644
index 0000000..58cdba1
--- /dev/null
+++ b/board/idmr/idmr.c
@@ -0,0 +1,169 @@
+/*
+ * (C) Copyright 2000-2006
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/m5271.h>
+#include <asm/immap_5271.h>
+
+int checkboard (void) {
+ puts ("Board: iDMR\n");
+ return 0;
+};
+
+long int initdram (int board_type) {
+ int i;
+
+ /*
+ * After reset, CS0 is configured to cover entire address space. We
+ * need to configure it to its proper values, so that writes to
+ * CFG_SDRAM_BASE and vicinity during SDRAM controller setup below do
+ * now fall under CS0 (see 16.3.1 of the MCF5271 Reference Manual).
+ */
+
+ /* Flash chipselect, CS0 */
+ /* ;CSAR0: Flash at 0xFF800000 */
+ mbar_writeShort(0x0080, 0xFF80);
+
+ /* CSCR0: Flash 6 waits, 16bit */
+ mbar_writeShort(0x008A, 0x1980);
+
+ /* CSMR0: Flash 8MB, R/W, valid */
+ mbar_writeLong(0x0084, 0x007F0001);
+
+
+ /*
+ * SDRAM configuration proper
+ */
+
+ /*
+ * Address/Data Pin Assignment Reg.: enable address lines 23-21; do
+ * not enable data pins D[15:0], as we have 16 bit port to SDRAM
+ */
+ mbar_writeByte(MCF_GPIO_PAR_AD,
+ MCF_GPIO_AD_ADDR23 |
+ MCF_GPIO_AD_ADDR22 |
+ MCF_GPIO_AD_ADDR21);
+
+ /* No need to configure BS pins - reset values are OK */
+
+ /* Chip Select Pin Assignment Reg.: set CS[1-7] to GPIO */
+ mbar_writeByte(MCF_GPIO_PAR_CS, 0x00);
+
+ /* SDRAM Control Pin Assignment Reg. */
+ mbar_writeByte(MCF_GPIO_PAR_SDRAM,
+ MCF_GPIO_SDRAM_CSSDCS_00 | /* no matter: PAR_CS=0 */
+ MCF_GPIO_SDRAM_SDWE |
+ MCF_GPIO_SDRAM_SCAS |
+ MCF_GPIO_SDRAM_SRAS |
+ MCF_GPIO_SDRAM_SCKE |
+ MCF_GPIO_SDRAM_SDCS_01);
+
+ /*
+ * Wait 100us. We run the bus at 50Mhz, one cycle is 20ns. So 5
+ * iterations will do, but we do 10 just to be safe.
+ */
+ for (i = 0; i < 10; ++i)
+ asm(" nop");
+
+
+ /* 1. Initialize DRAM Control Register: DCR */
+ mbar_writeShort(MCF_SDRAMC_DCR,
+ MCF_SDRAMC_DCR_RTIM(0x10) | /* 65ns */
+ MCF_SDRAMC_DCR_RC(0x60)); /* 1562 cycles */
+
+
+ /*
+ * 2. Initialize DACR0
+ *
+ * CL: 11 (CL=3: 0x03, 0x02; CL=2: 0x1)
+ * CBM: cmd at A20, bank select bits 21 and up
+ * PS: 16 bit
+ */
+ mbar_writeLong(MCF_SDRAMC_DACR0,
+ MCF_SDRAMC_DACRn_BA(CFG_SDRAM_BASE>>18) |
+ MCF_SDRAMC_DACRn_BA(0x00) |
+ MCF_SDRAMC_DACRn_CASL(0x03) |
+ MCF_SDRAMC_DACRn_CBM(0x03) |
+ MCF_SDRAMC_DACRn_PS(0x03));
+
+ /* Initialize DMR0 */
+ mbar_writeLong(MCF_SDRAMC_DMR0,
+ MCF_SDRAMC_DMRn_BAM_16M |
+ MCF_SDRAMC_DMRn_V);
+
+
+ /* 3. Set IP bit in DACR to initiate PALL command */
+ mbar_writeLong(MCF_SDRAMC_DACR0,
+ mbar_readLong(MCF_SDRAMC_DACR0) |
+ MCF_SDRAMC_DACRn_IP);
+
+ /* Write to this block to initiate precharge */
+ *(volatile u16 *)(CFG_SDRAM_BASE) = 0xa5a5;
+
+ /*
+ * Wait at least 20ns to allow banks to precharge (t_RP = 20ns). We
+ * wait a wee longer, just to be safe.
+ */
+ for (i = 0; i < 5; ++i)
+ asm(" nop");
+
+
+ /* 4. Set RE bit in DACR */
+ mbar_writeLong(MCF_SDRAMC_DACR0,
+ mbar_readLong(MCF_SDRAMC_DACR0) |
+ MCF_SDRAMC_DACRn_RE);
+
+ /*
+ * Wait for at least 8 auto refresh cycles to occur, i.e. at least
+ * 781 bus cycles.
+ */
+ for (i = 0; i < 1000; ++i)
+ asm(" nop");
+
+ /* Finish the configuration by issuing the MRS */
+ mbar_writeLong(MCF_SDRAMC_DACR0,
+ mbar_readLong(MCF_SDRAMC_DACR0) |
+ MCF_SDRAMC_DACRn_MRS);
+
+ /*
+ * Write to the SDRAM Mode Register A0-A11 = 0x400
+ *
+ * Write Burst Mode = Programmed Burst Length
+ * Op Mode = Standard Op
+ * CAS Latency = 3
+ * Burst Type = Sequential
+ * Burst Length = 1
+ */
+ *(volatile u32 *)(CFG_SDRAM_BASE + 0x1800) = 0xa5a5a5a5;
+
+ return CFG_SDRAM_SIZE * 1024 * 1024;
+};
+
+
+int testdram (void) {
+
+ /* TODO: XXX XXX XXX */
+ printf ("DRAM test not implemented!\n");
+
+ return (0);
+}