diff options
Diffstat (limited to 'board/freescale')
-rw-r--r-- | board/freescale/mx6sxsabresd/mx6sxsabresd.c | 152 |
1 files changed, 135 insertions, 17 deletions
diff --git a/board/freescale/mx6sxsabresd/mx6sxsabresd.c b/board/freescale/mx6sxsabresd/mx6sxsabresd.c index 32d4e6d..d242072 100644 --- a/board/freescale/mx6sxsabresd/mx6sxsabresd.c +++ b/board/freescale/mx6sxsabresd/mx6sxsabresd.c @@ -14,6 +14,7 @@ #include <asm/arch/sys_proto.h> #include <asm/gpio.h> #include <asm/imx-common/iomux-v3.h> +#include <asm/imx-common/boot_mode.h> #include <asm/io.h> #include <asm/imx-common/mxc_i2c.h> #include <linux/sizes.h> @@ -63,6 +64,12 @@ DECLARE_GLOBAL_DATA_PTR; #define LCD_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_PUS_100K_UP | PAD_CTL_PUE | \ PAD_CTL_PKE | PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm) +#define BUTTON_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \ + PAD_CTL_PUS_22K_UP | PAD_CTL_DSE_40ohm) + +#define WDOG_PAD_CTRL (PAD_CTL_PUE | PAD_CTL_PKE | PAD_CTL_SPEED_MED | \ + PAD_CTL_DSE_40ohm) + int dram_init(void) { gd->ram_size = imx_ddr_size(); @@ -113,6 +120,23 @@ static iomux_v3_cfg_t const usdhc4_pads[] = { MX6_PAD_SD4_DATA7__GPIO6_IO_21 | MUX_PAD_CTRL(NO_PAD_CTRL), }; +static iomux_v3_cfg_t const usdhc4_emmc_pads[] = { + MX6_PAD_SD4_CLK__USDHC4_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD4_CMD__USDHC4_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD4_DATA0__USDHC4_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD4_DATA1__USDHC4_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD4_DATA2__USDHC4_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD4_DATA3__USDHC4_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD4_DATA4__USDHC4_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD4_DATA5__USDHC4_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD4_DATA6__USDHC4_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD4_DATA7__USDHC4_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD4_RESET_B__USDHC4_RESET_B | MUX_PAD_CTRL(NO_PAD_CTRL), +}; + +static iomux_v3_cfg_t const wdog_b_pad = { + MX6_PAD_GPIO1_IO13__GPIO1_IO_13 | MUX_PAD_CTRL(WDOG_PAD_CTRL), +}; static iomux_v3_cfg_t const fec1_pads[] = { MX6_PAD_ENET1_MDC__ENET1_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL), MX6_PAD_ENET1_MDIO__ENET1_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL), @@ -162,6 +186,20 @@ static iomux_v3_cfg_t const phy_control_pads[] = { MX6_PAD_ENET2_CRS__GPIO2_IO_7 | MUX_PAD_CTRL(NO_PAD_CTRL), }; +#ifdef CONFIG_PCIE_IMX +iomux_v3_cfg_t const pcie_pads[] = { + MX6_PAD_ENET1_COL__GPIO2_IO_0 | MUX_PAD_CTRL(NO_PAD_CTRL), /* POWER */ + MX6_PAD_ENET1_CRS__GPIO2_IO_1 | MUX_PAD_CTRL(NO_PAD_CTRL), /* RESET */ +}; + +static void setup_pcie(void) +{ + imx_iomux_v3_setup_multiple_pads(pcie_pads, ARRAY_SIZE(pcie_pads)); + gpio_request(CONFIG_PCIE_IMX_POWER_GPIO, "PCIE Power Enable"); + gpio_request(CONFIG_PCIE_IMX_PERST_GPIO, "PCIE Reset"); +} +#endif + static void setup_iomux_uart(void) { imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads)); @@ -229,25 +267,64 @@ static struct i2c_pads_info i2c_pad_info1 = { }, }; +/* I2C2 */ +struct i2c_pads_info i2c_pad_info2 = { + .scl = { + .i2c_mode = MX6_PAD_GPIO1_IO02__I2C2_SCL | PC, + .gpio_mode = MX6_PAD_GPIO1_IO02__GPIO1_IO_2 | PC, + .gp = IMX_GPIO_NR(1, 2), + }, + .sda = { + .i2c_mode = MX6_PAD_GPIO1_IO03__I2C2_SDA | PC, + .gpio_mode = MX6_PAD_GPIO1_IO03__GPIO1_IO_3 | PC, + .gp = IMX_GPIO_NR(1, 3), + }, +}; + + int power_init_board(void) { - struct pmic *p; + struct pmic *pfuze; unsigned int reg; int ret; - p = pfuze_common_init(I2C_PMIC); - if (!p) + pfuze = pfuze_common_init(I2C_PMIC); + if (!pfuze) return -ENODEV; - ret = pfuze_mode_init(p, APS_PFM); + ret = pfuze_mode_init(pfuze, APS_PFM); if (ret < 0) return ret; + /* set SW1AB standby volatage 1.10V */ + pmic_reg_read(pfuze, PFUZE100_SW1ABSTBY, ®); + reg &= ~0x3f; + reg |= PFUZE100_SW1ABC_SETP(11000); + pmic_reg_write(pfuze, PFUZE100_SW1ABSTBY, reg); + + /* set SW1AB/VDDARM step ramp up time from 16us to 4us/25mV */ + pmic_reg_read(pfuze, PFUZE100_SW1ABCONF, ®); + reg &= ~0xc0; + reg |= 0x40; + pmic_reg_write(pfuze, PFUZE100_SW1ABCONF, reg); + + /* set SW1C standby volatage 1.10V */ + pmic_reg_read(pfuze, PFUZE100_SW1CSTBY, ®); + reg &= ~0x3f; + reg |= PFUZE100_SW1ABC_SETP(11000); + pmic_reg_write(pfuze, PFUZE100_SW1CSTBY, reg); + + /* set SW1C/VDDSOC step ramp up time to from 16us to 4us/25mV */ + pmic_reg_read(pfuze, PFUZE100_SW1CCONF, ®); + reg &= ~0xc0; + reg |= 0x40; + pmic_reg_write(pfuze, PFUZE100_SW1CCONF, reg); + /* Enable power of VGEN5 3V3, needed for SD3 */ - pmic_reg_read(p, PFUZE100_VGEN5VOL, ®); + pmic_reg_read(pfuze, PFUZE100_VGEN5VOL, ®); reg &= ~LDO_VOL_MASK; reg |= (LDOB_3_30V | (1 << LDO_EN)); - pmic_reg_write(p, PFUZE100_VGEN5VOL, reg); + pmic_reg_write(pfuze, PFUZE100_VGEN5VOL, reg); return 0; } @@ -318,24 +395,17 @@ int board_early_init_f(void) { setup_iomux_uart(); - /* Enable PERI_3V3, which is used by SD2, ENET, LVDS, BT */ - imx_iomux_v3_setup_multiple_pads(peri_3v3_pads, - ARRAY_SIZE(peri_3v3_pads)); - - /* Active high for ncp692 */ - gpio_direction_output(IMX_GPIO_NR(4, 16) , 1); - -#ifdef CONFIG_USB_EHCI_MX6 - setup_usb(); -#endif - return 0; } static struct fsl_esdhc_cfg usdhc_cfg[3] = { {USDHC2_BASE_ADDR, 0, 4}, {USDHC3_BASE_ADDR}, +#ifdef CONFIG_MX6SXSABRESD_EMMC_REWORK + {USDHC4_BASE_ADDR, 0, 8}, +#else {USDHC4_BASE_ADDR}, +#endif }; #define USDHC3_CD_GPIO IMX_GPIO_NR(2, 10) @@ -365,7 +435,11 @@ int board_mmc_getcd(struct mmc *mmc) ret = !gpio_get_value(USDHC3_CD_GPIO); break; case USDHC4_BASE_ADDR: +#ifdef CONFIG_MX6SXSABRESD_EMMC_REWORK + ret = 1; +#else ret = !gpio_get_value(USDHC4_CD_GPIO); +#endif break; } @@ -399,9 +473,14 @@ int board_mmc_init(bd_t *bis) usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK); break; case 2: +#ifdef CONFIG_MX6SXSABRESD_EMMC_REWORK + imx_iomux_v3_setup_multiple_pads( + usdhc4_emmc_pads, ARRAY_SIZE(usdhc4_emmc_pads)); +#else imx_iomux_v3_setup_multiple_pads( usdhc4_pads, ARRAY_SIZE(usdhc4_pads)); gpio_direction_input(USDHC4_CD_GPIO); +#endif usdhc_cfg[2].sdhc_clk = mxc_get_clock(MXC_ESDHC4_CLK); break; default: @@ -497,6 +576,16 @@ int board_qspi_init(void) } #endif +#ifdef CONFIG_CMD_BMODE +static const struct boot_mode board_boot_modes[] = { + /* 4 bit bus width */ + {"sd3", MAKE_CFGVAL(0x42, 0x30, 0x00, 0x00)}, + {"sd4", MAKE_CFGVAL(0x40, 0x38, 0x00, 0x00)}, + {"qspi2", MAKE_CFGVAL(0x18, 0x00, 0x00, 0x00)}, + {NULL, 0}, +}; +#endif + #ifdef CONFIG_VIDEO_MXS static iomux_v3_cfg_t const lvds_ctrl_pads[] = { /* CABC enable */ @@ -635,19 +724,48 @@ int board_init(void) /* Address of boot parameters */ gd->bd->bi_boot_params = PHYS_SDRAM + 0x100; + /* + * Because kernel set WDOG_B mux before pad with the commone pinctrl + * framwork now and wdog reset will be triggered once set WDOG_B mux + * with default pad setting, we set pad setting here to workaround this. + * Since imx_iomux_v3_setup_pad also set mux before pad setting, we set + * as GPIO mux firstly here to workaround it. + */ + imx_iomux_v3_setup_pad(wdog_b_pad); + + /* Enable PERI_3V3, which is used by SD2, ENET, LVDS, BT */ + imx_iomux_v3_setup_multiple_pads(peri_3v3_pads, + ARRAY_SIZE(peri_3v3_pads)); + + /* Active high for ncp692 */ + gpio_direction_output(IMX_GPIO_NR(4, 16) , 1); + #ifdef CONFIG_SYS_I2C_MXC setup_i2c(0, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info1); + setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info2); +#endif + +#ifdef CONFIG_USB_EHCI_MX6 + setup_usb(); #endif #ifdef CONFIG_FSL_QSPI board_qspi_init(); #endif +#ifdef CONFIG_PCIE_IMX + setup_pcie(); +#endif + return 0; } int board_late_init(void) { +#ifdef CONFIG_CMD_BMODE + add_board_boot_modes(board_boot_modes); +#endif + #ifdef CONFIG_ENV_IS_IN_MMC board_late_mmc_env_init(); #endif |