summaryrefslogtreecommitdiff
path: root/board/esd/meesc
diff options
context:
space:
mode:
Diffstat (limited to 'board/esd/meesc')
-rw-r--r--board/esd/meesc/meesc.c65
1 files changed, 58 insertions, 7 deletions
diff --git a/board/esd/meesc/meesc.c b/board/esd/meesc/meesc.c
index 636d0ed..efba60d 100644
--- a/board/esd/meesc/meesc.c
+++ b/board/esd/meesc/meesc.c
@@ -126,8 +126,10 @@ static void meesc_ethercat_hw_init(void)
AT91_SMC_NRDPULSE_(4) | AT91_SMC_NCS_RDPULSE_(9));
at91_sys_write(AT91_SMC1_CYCLE(0),
AT91_SMC_NWECYCLE_(10) | AT91_SMC_NRDCYCLE_(5));
- /* Configure behavior at external wait signal, byte-select mode, 16 bit
- data bus width, none data float wait states and TDF optimization */
+ /*
+ * Configure behavior at external wait signal, byte-select mode, 16 bit
+ * data bus width, none data float wait states and TDF optimization
+ */
at91_sys_write(AT91_SMC1_MODE(0),
AT91_SMC_READMODE | AT91_SMC_EXNWMODE_READY |
AT91_SMC_BAT_SELECT | AT91_SMC_DBW_16 | AT91_SMC_TDF_(0) |
@@ -156,8 +158,32 @@ int board_eth_init(bd_t *bis)
int checkboard(void)
{
char str[32];
-
- puts("Board: esd CAN-EtherCAT Gateway");
+ u_char hw_type; /* hardware type */
+
+ /* read the "Type" register of the ET1100 controller */
+ hw_type = readb(CONFIG_ET1100_BASE);
+
+ switch (hw_type) {
+ case 0x11:
+ case 0x3F:
+ /* ET1100 present, arch number of MEESC-Board */
+ gd->bd->bi_arch_number = MACH_TYPE_MEESC;
+ puts("Board: CAN-EtherCAT Gateway");
+ break;
+ case 0xFF:
+ /* no ET1100 present, arch number of EtherCAN/2-Board */
+ gd->bd->bi_arch_number = MACH_TYPE_ETHERCAN2;
+ puts("Board: EtherCAN/2 Gateway");
+ /* switch on LED1D */
+ at91_set_gpio_output(AT91_PIN_PB12, 1);
+ break;
+ default:
+ /* assume, no ET1100 present, arch number of EtherCAN/2-Board */
+ gd->bd->bi_arch_number = MACH_TYPE_ETHERCAN2;
+ printf("ERROR! Read invalid hw_type: %02X\n", hw_type);
+ puts("Board: EtherCAN/2 Gateway");
+ break;
+ }
if (getenv_r("serial#", str, sizeof(str)) > 0) {
puts(", serial# ");
puts(str);
@@ -167,6 +193,32 @@ int checkboard(void)
return 0;
}
+#ifdef CONFIG_SERIAL_TAG
+void get_board_serial(struct tag_serialnr *serialnr)
+{
+ char *str;
+
+ char *serial = getenv("serial#");
+ if (serial) {
+ str = strchr(serial, '_');
+ if (str && (strlen(str) >= 4)) {
+ serialnr->high = (*(str + 1) << 8) | *(str + 2);
+ serialnr->low = simple_strtoul(str + 3, NULL, 16);
+ }
+ } else {
+ serialnr->high = 0;
+ serialnr->low = 0;
+ }
+}
+#endif
+
+#ifdef CONFIG_REVISION_TAG
+u32 get_board_rev(void)
+{
+ return hw_rev | 0x100;
+}
+#endif
+
int board_init(void)
{
/* Peripheral Clock Enable Register */
@@ -174,8 +226,8 @@ int board_init(void)
1 << AT91SAM9263_ID_PIOB |
1 << AT91SAM9263_ID_PIOCDE);
- /* arch number of MEESC-Board */
- gd->bd->bi_arch_number = MACH_TYPE_MEESC;
+ /* initialize ET1100 Controller */
+ meesc_ethercat_hw_init();
/* adress of boot parameters */
gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
@@ -184,7 +236,6 @@ int board_init(void)
#ifdef CONFIG_CMD_NAND
meesc_nand_hw_init();
#endif
- meesc_ethercat_hw_init();
#ifdef CONFIG_HAS_DATAFLASH
at91_spi0_hw_init(1 << 0);
#endif