summaryrefslogtreecommitdiff
path: root/board/amcc/sequoia
diff options
context:
space:
mode:
Diffstat (limited to 'board/amcc/sequoia')
-rw-r--r--board/amcc/sequoia/config.mk4
-rw-r--r--board/amcc/sequoia/sequoia.c173
-rw-r--r--board/amcc/sequoia/u-boot.lds142
3 files changed, 5 insertions, 314 deletions
diff --git a/board/amcc/sequoia/config.mk b/board/amcc/sequoia/config.mk
index 6c748c9..b57e473 100644
--- a/board/amcc/sequoia/config.mk
+++ b/board/amcc/sequoia/config.mk
@@ -43,3 +43,7 @@ endif
ifeq ($(dbcr),1)
PLATFORM_CPPFLAGS += -DCONFIG_SYS_INIT_DBCR=0x8cff0000
endif
+
+ifdef CONFIG_NAND_U_BOOT
+LDSCRIPT := $(TOPDIR)/board/$(BOARDDIR)/u-boot-nand.lds
+endif
diff --git a/board/amcc/sequoia/sequoia.c b/board/amcc/sequoia/sequoia.c
index 00f6408..6756a27 100644
--- a/board/amcc/sequoia/sequoia.c
+++ b/board/amcc/sequoia/sequoia.c
@@ -364,183 +364,12 @@ int checkboard(void)
/*
* Assign interrupts to PCI devices.
*/
-void sequoia_pci_fixup_irq(struct pci_controller *hose, pci_dev_t dev)
+void board_pci_fixup_irq(struct pci_controller *hose, pci_dev_t dev)
{
pci_hose_write_config_byte(hose, dev, PCI_INTERRUPT_LINE, VECNUM_EIRQ2);
}
#endif
-/*
- * pci_pre_init
- *
- * This routine is called just prior to registering the hose and gives
- * the board the opportunity to check things. Returning a value of zero
- * indicates that things are bad & PCI initialization should be aborted.
- *
- * Different boards may wish to customize the pci controller structure
- * (add regions, override default access routines, etc) or perform
- * certain pre-initialization actions.
- */
-#if defined(CONFIG_PCI)
-int pci_pre_init(struct pci_controller *hose)
-{
- unsigned long addr;
-
- /*
- * Set priority for all PLB3 devices to 0.
- * Set PLB3 arbiter to fair mode.
- */
- mfsdr(SD0_AMP1, addr);
- mtsdr(SD0_AMP1, (addr & 0x000000FF) | 0x0000FF00);
- addr = mfdcr(PLB3_ACR);
- mtdcr(PLB3_ACR, addr | 0x80000000);
-
- /*
- * Set priority for all PLB4 devices to 0.
- */
- mfsdr(SD0_AMP0, addr);
- mtsdr(SD0_AMP0, (addr & 0x000000FF) | 0x0000FF00);
- addr = mfdcr(PLB4_ACR) | 0xa0000000; /* Was 0x8---- */
- mtdcr(PLB4_ACR, addr);
-
- /*
- * Set Nebula PLB4 arbiter to fair mode.
- */
- /* Segment0 */
- addr = (mfdcr(PLB0_ACR) & ~PLB0_ACR_PPM_MASK) | PLB0_ACR_PPM_FAIR;
- addr = (addr & ~PLB0_ACR_HBU_MASK) | PLB0_ACR_HBU_ENABLED;
- addr = (addr & ~PLB0_ACR_RDP_MASK) | PLB0_ACR_RDP_4DEEP;
- addr = (addr & ~PLB0_ACR_WRP_MASK) | PLB0_ACR_WRP_2DEEP;
- mtdcr(PLB0_ACR, addr);
-
- /* Segment1 */
- addr = (mfdcr(PLB1_ACR) & ~PLB1_ACR_PPM_MASK) | PLB1_ACR_PPM_FAIR;
- addr = (addr & ~PLB1_ACR_HBU_MASK) | PLB1_ACR_HBU_ENABLED;
- addr = (addr & ~PLB1_ACR_RDP_MASK) | PLB1_ACR_RDP_4DEEP;
- addr = (addr & ~PLB1_ACR_WRP_MASK) | PLB1_ACR_WRP_2DEEP;
- mtdcr(PLB1_ACR, addr);
-
-#ifdef CONFIG_PCI_PNP
- hose->fixup_irq = sequoia_pci_fixup_irq;
-#endif
- return 1;
-}
-#endif /* defined(CONFIG_PCI) */
-
-/*
- * pci_target_init
- *
- * The bootstrap configuration provides default settings for the pci
- * inbound map (PIM). But the bootstrap config choices are limited and
- * may not be sufficient for a given board.
- */
-#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT)
-void pci_target_init(struct pci_controller *hose)
-{
- /*
- * Set up Direct MMIO registers
- */
- /*
- * PowerPC440EPX PCI Master configuration.
- * Map one 1Gig range of PLB/processor addresses to PCI memory space.
- * PLB address 0xA0000000-0xDFFFFFFF
- * ==> PCI address 0xA0000000-0xDFFFFFFF
- * Use byte reversed out routines to handle endianess.
- * Make this region non-prefetchable.
- */
- out32r(PCIL0_PMM0MA, 0x00000000); /* PMM0 Mask/Attribute */
- /* - disabled b4 setting */
- out32r(PCIL0_PMM0LA, CONFIG_SYS_PCI_MEMBASE); /* PMM0 Local Address */
- out32r(PCIL0_PMM0PCILA, CONFIG_SYS_PCI_MEMBASE); /* PMM0 PCI Low Address */
- out32r(PCIL0_PMM0PCIHA, 0x00000000); /* PMM0 PCI High Address */
- out32r(PCIL0_PMM0MA, 0xE0000001); /* 512M + No prefetching, */
- /* and enable region */
-
- out32r(PCIL0_PMM1MA, 0x00000000); /* PMM0 Mask/Attribute */
- /* - disabled b4 setting */
- out32r(PCIL0_PMM1LA, CONFIG_SYS_PCI_MEMBASE2); /* PMM0 Local Address */
- out32r(PCIL0_PMM1PCILA, CONFIG_SYS_PCI_MEMBASE2); /* PMM0 PCI Low Address */
- out32r(PCIL0_PMM1PCIHA, 0x00000000); /* PMM0 PCI High Address */
- out32r(PCIL0_PMM1MA, 0xE0000001); /* 512M + No prefetching, */
- /* and enable region */
-
- out32r(PCIL0_PTM1MS, 0x00000001); /* Memory Size/Attribute */
- out32r(PCIL0_PTM1LA, 0); /* Local Addr. Reg */
- out32r(PCIL0_PTM2MS, 0); /* Memory Size/Attribute */
- out32r(PCIL0_PTM2LA, 0); /* Local Addr. Reg */
-
- /*
- * Set up Configuration registers
- */
-
- /* Program the board's subsystem id/vendor id */
- pci_write_config_word(0, PCI_SUBSYSTEM_VENDOR_ID,
- CONFIG_SYS_PCI_SUBSYS_VENDORID);
- pci_write_config_word(0, PCI_SUBSYSTEM_ID, CONFIG_SYS_PCI_SUBSYS_ID);
-
- /* Configure command register as bus master */
- pci_write_config_word(0, PCI_COMMAND, PCI_COMMAND_MASTER);
-
- /* 240nS PCI clock */
- pci_write_config_word(0, PCI_LATENCY_TIMER, 1);
-
- /* No error reporting */
- pci_write_config_word(0, PCI_ERREN, 0);
-
- pci_write_config_dword(0, PCI_BRDGOPT2, 0x00000101);
-
-}
-#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) */
-
-#if defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_MASTER_INIT)
-void pci_master_init(struct pci_controller *hose)
-{
- unsigned short temp_short;
-
- /*
- * Write the PowerPC440 EP PCI Configuration regs.
- * Enable PowerPC440 EP to be a master on the PCI bus (PMM).
- * Enable PowerPC440 EP to act as a PCI memory target (PTM).
- */
- pci_read_config_word(0, PCI_COMMAND, &temp_short);
- pci_write_config_word(0, PCI_COMMAND,
- temp_short | PCI_COMMAND_MASTER |
- PCI_COMMAND_MEMORY);
-}
-#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_MASTER_INIT) */
-
-/*
- * is_pci_host
- *
- * This routine is called to determine if a pci scan should be
- * performed. With various hardware environments (especially cPCI and
- * PPMC) it's insufficient to depend on the state of the arbiter enable
- * bit in the strap register, or generic host/adapter assumptions.
- *
- * Rather than hard-code a bad assumption in the general 440 code, the
- * 440 pci code requires the board to decide at runtime.
- *
- * Return 0 for adapter mode, non-zero for host (monarch) mode.
- */
-#if defined(CONFIG_PCI)
-int is_pci_host(struct pci_controller *hose)
-{
- /* Cactus is always configured as host. */
- return (1);
-}
-#endif /* defined(CONFIG_PCI) */
-
-#if defined(CONFIG_POST)
-/*
- * Returns 1 if keys pressed to start the power-on long-running tests
- * Called from board_init_f().
- */
-int post_hotkeys_pressed(void)
-{
- return 0; /* No hotkeys supported */
-}
-#endif /* CONFIG_POST */
-
#if defined(CONFIG_NAND_U_BOOT) || defined(CONFIG_SYS_RAMBOOT)
/*
* On NAND-booting sequoia, we need to patch the chips select numbers
diff --git a/board/amcc/sequoia/u-boot.lds b/board/amcc/sequoia/u-boot.lds
deleted file mode 100644
index b9ec56b..0000000
--- a/board/amcc/sequoia/u-boot.lds
+++ /dev/null
@@ -1,142 +0,0 @@
-/*
- * (C) Copyright 2002
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-OUTPUT_ARCH(powerpc)
-/* Do we need any of these for elf?
- __DYNAMIC = 0; */
-SECTIONS
-{
- .resetvec 0xFFFFFFFC :
- {
- *(.resetvec)
- } = 0xffff
-
- .bootpg 0xFFFFF000 :
- {
- cpu/ppc4xx/start.o (.bootpg)
- } = 0xffff
-
- /* Read-only sections, merged into text segment: */
- . = + SIZEOF_HEADERS;
- .interp : { *(.interp) }
- .hash : { *(.hash) }
- .dynsym : { *(.dynsym) }
- .dynstr : { *(.dynstr) }
- .rel.text : { *(.rel.text) }
- .rela.text : { *(.rela.text) }
- .rel.data : { *(.rel.data) }
- .rela.data : { *(.rela.data) }
- .rel.rodata : { *(.rel.rodata) }
- .rela.rodata : { *(.rela.rodata) }
- .rel.got : { *(.rel.got) }
- .rela.got : { *(.rela.got) }
- .rel.ctors : { *(.rel.ctors) }
- .rela.ctors : { *(.rela.ctors) }
- .rel.dtors : { *(.rel.dtors) }
- .rela.dtors : { *(.rela.dtors) }
- .rel.bss : { *(.rel.bss) }
- .rela.bss : { *(.rela.bss) }
- .rel.plt : { *(.rel.plt) }
- .rela.plt : { *(.rela.plt) }
- .init : { *(.init) }
- .plt : { *(.plt) }
- .text :
- {
- /* WARNING - the following is hand-optimized to fit within */
- /* the sector layout of our flash chips! XXX FIXME XXX */
-
- cpu/ppc4xx/start.o (.text)
-
- *(.text)
- *(.got1)
- }
- _etext = .;
- PROVIDE (etext = .);
- .rodata :
- {
- *(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*)))
- }
- .fini : { *(.fini) } =0
- .ctors : { *(.ctors) }
- .dtors : { *(.dtors) }
-
- /* Read-write section, merged into data segment: */
- . = (. + 0x00FF) & 0xFFFFFF00;
- _erotext = .;
- PROVIDE (erotext = .);
- .reloc :
- {
- *(.got)
- _GOT2_TABLE_ = .;
- *(.got2)
- _FIXUP_TABLE_ = .;
- *(.fixup)
- }
- __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >>2;
- __fixup_entries = (. - _FIXUP_TABLE_)>>2;
-
- .data :
- {
- *(.data)
- *(.data1)
- *(.sdata)
- *(.sdata2)
- *(.dynamic)
- CONSTRUCTORS
- }
- _edata = .;
- PROVIDE (edata = .);
-
- . = .;
- __u_boot_cmd_start = .;
- .u_boot_cmd : { *(.u_boot_cmd) }
- __u_boot_cmd_end = .;
-
-
- . = .;
- __start___ex_table = .;
- __ex_table : { *(__ex_table) }
- __stop___ex_table = .;
-
- . = ALIGN(256);
- __init_begin = .;
- .text.init : { *(.text.init) }
- .data.init : { *(.data.init) }
- . = ALIGN(256);
- __init_end = .;
-
- __bss_start = .;
- .bss (NOLOAD) :
- {
- *(.sbss) *(.scommon)
- *(.dynbss)
- *(.bss)
- *(COMMON)
- . = ALIGN(4);
- }
-
- ppcenv_assert = ASSERT(. < 0xFFFF8000, ".bss section too big, overlaps .ppcenv section. Please update your confguration: CONFIG_SYS_MONITOR_BASE, CONFIG_SYS_MONITOR_LEN and TEXT_BASE may need to be modified.");
-
- _end = . ;
- PROVIDE (end = .);
-}
generated by cgit v1.1 at 2024-12-25 06:41:50 +0000