diff options
Diffstat (limited to 'board/Marvell/rd6281a/rd6281a.c')
| -rw-r--r-- | board/Marvell/rd6281a/rd6281a.c | 157 |
1 files changed, 0 insertions, 157 deletions
diff --git a/board/Marvell/rd6281a/rd6281a.c b/board/Marvell/rd6281a/rd6281a.c deleted file mode 100644 index b0020c9..0000000 --- a/board/Marvell/rd6281a/rd6281a.c +++ /dev/null @@ -1,157 +0,0 @@ -/* - * (C) Copyright 2009 - * Marvell Semiconductor <www.marvell.com> - * Written-by: Prafulla Wadaskar <prafulla@marvell.com> - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -#include <common.h> -#include <miiphy.h> -#include <netdev.h> -#include <asm/arch/cpu.h> -#include <asm/arch/soc.h> -#include <asm/arch/mpp.h> -#include "rd6281a.h" - -DECLARE_GLOBAL_DATA_PTR; - -int board_early_init_f(void) -{ - /* - * default gpio configuration - * There are maximum 64 gpios controlled through 2 sets of registers - * the below configuration configures mainly initial LED status - */ - mvebu_config_gpio(RD6281A_OE_VAL_LOW, - RD6281A_OE_VAL_HIGH, - RD6281A_OE_LOW, RD6281A_OE_HIGH); - - /* Multi-Purpose Pins Functionality configuration */ - static const u32 kwmpp_config[] = { - MPP0_NF_IO2, - MPP1_NF_IO3, - MPP2_NF_IO4, - MPP3_NF_IO5, - MPP4_NF_IO6, - MPP5_NF_IO7, - MPP6_SYSRST_OUTn, - MPP7_GPO, - MPP8_TW_SDA, - MPP9_TW_SCK, - MPP10_UART0_TXD, - MPP11_UART0_RXD, - MPP12_SD_CLK, - MPP13_SD_CMD, - MPP14_SD_D0, - MPP15_SD_D1, - MPP16_SD_D2, - MPP17_SD_D3, - MPP18_NF_IO0, - MPP19_NF_IO1, - MPP20_GE1_0, - MPP21_GE1_1, - MPP22_GE1_2, - MPP23_GE1_3, - MPP24_GE1_4, - MPP25_GE1_5, - MPP26_GE1_6, - MPP27_GE1_7, - MPP28_GPIO, - MPP29_GPIO, - MPP30_GE1_10, - MPP31_GE1_11, - MPP32_GE1_12, - MPP33_GE1_13, - MPP34_GE1_14, - MPP35_GPIO, - MPP36_AUDIO_SPDIFI, - MPP37_AUDIO_SPDIFO, - MPP38_GPIO, - MPP39_TDM_SPI_CS0, - MPP40_TDM_SPI_SCK, - MPP41_TDM_SPI_MISO, - MPP42_TDM_SPI_MOSI, - MPP43_TDM_CODEC_INTn, - MPP44_GPIO, - MPP45_TDM_PCLK, - MPP46_TDM_FS, - MPP47_TDM_DRX, - MPP48_TDM_DTX, - MPP49_GPIO, - 0 - }; - kirkwood_mpp_conf(kwmpp_config, NULL); - return 0; -} - -int board_init(void) -{ - /* - * arch number of board - */ - gd->bd->bi_arch_number = MACH_TYPE_RD88F6281; - - /* adress of boot parameters */ - gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100; - - return 0; -} - -void mv_phy_88e1116_init(char *name) -{ - u16 reg; - u16 devadr; - - if (miiphy_set_current_dev(name)) - return; - - /* command to read PHY dev address */ - if (miiphy_read(name, 0xEE, 0xEE, (u16 *) &devadr)) { - printf("Err..%s could not read PHY dev address\n", - __FUNCTION__); - return; - } - - /* - * Enable RGMII delay on Tx and Rx for CPU port - * Ref: sec 4.7.2 of chip datasheet - */ - miiphy_write(name, devadr, MV88E1116_PGADR_REG, 2); - miiphy_read(name, devadr, MV88E1116_MAC_CTRL_REG, ®); - reg |= (MV88E1116_RGMII_RXTM_CTRL | MV88E1116_RGMII_TXTM_CTRL); - miiphy_write(name, devadr, MV88E1116_MAC_CTRL_REG, reg); - miiphy_write(name, devadr, MV88E1116_PGADR_REG, 0); - - /* reset the phy */ - if (miiphy_read (name, devadr, MII_BMCR, ®) != 0) { - printf("Err..(%s) PHY status read failed\n", __FUNCTION__); - return; - } - if (miiphy_write (name, devadr, MII_BMCR, reg | 0x8000) != 0) { - printf("Err..(%s) PHY reset failed\n", __FUNCTION__); - return; - } - - printf("88E1116 Initialized on %s\n", name); -} - -/* Configure and enable Switch and PHY */ -void reset_phy(void) -{ - /* configure and initialize switch */ - struct mv88e61xx_config swcfg = { - .name = "egiga0", - .vlancfg = MV88E61XX_VLANCFG_ROUTER, - .rgmii_delay = MV88E61XX_RGMII_DELAY_EN, - .led_init = MV88E61XX_LED_INIT_EN, - .portstate = MV88E61XX_PORTSTT_FORWARDING, - .cpuport = (1 << 5), - .ports_enabled = 0x3f, - }; - - mv88e61xx_switch_initialize(&swcfg); - - /* configure and initialize PHY */ - mv_phy_88e1116_init("egiga1"); -} |