3 files changed, 155 insertions, 0 deletions

diff --git a/arch/arm/cpu/armv7/mx6/soc.c b/arch/arm/cpu/armv7/mx6/soc.c
index dd34138..0d1801c 100644
--- a/arch/arm/cpu/armv7/mx6/soc.c
+++ b/arch/arm/cpu/armv7/mx6/soc.c
@@ -18,6 +18,7 @@
 #include <asm/arch/sys_proto.h>
 #include <asm/imx-common/boot_mode.h>
 #include <asm/imx-common/dma.h>
+#include <libfdt.h>
 #include <stdbool.h>
 #include <asm/arch/mxc_hdmi.h>
 #include <asm/arch/crm_regs.h>
@@ -475,6 +476,147 @@ void s_init(void)
 	writel(mask528, &anatop->pfd_528_clr);
 }
 
+#ifdef CONFIG_LDO_BYPASS_CHECK
+DECLARE_GLOBAL_DATA_PTR;
+static int ldo_bypass;
+
+int check_ldo_bypass(void)
+{
+	const int *ldo_mode;
+	int node;
+
+	/* get the right fdt_blob from the global working_fdt */
+	gd->fdt_blob = working_fdt;
+	/* Get the node from FDT for anatop ldo-bypass */
+	node = fdt_node_offset_by_compatible(gd->fdt_blob, -1,
+		"fsl,imx6q-gpc");
+	if (node < 0) {
+		printf("No gpc device node %d, force to ldo-enable.\n", node);
+		return 0;
+	}
+	ldo_mode = fdt_getprop(gd->fdt_blob, node, "fsl,ldo-bypass", NULL);
+	/*
+	 * return 1 if "fsl,ldo-bypass = <1>", else return 0 if
+	 * "fsl,ldo-bypass = <0>" or no "fsl,ldo-bypass" property
+	 */
+	ldo_bypass = fdt32_to_cpu(*ldo_mode) == 1 ? 1 : 0;
+
+	return ldo_bypass;
+}
+
+int check_1_2G(void)
+{
+	u32 reg;
+	int result = 0;
+	struct ocotp_regs *ocotp = (struct ocotp_regs *)OCOTP_BASE_ADDR;
+	struct fuse_bank *bank = &ocotp->bank[0];
+	struct fuse_bank0_regs *fuse_bank0 =
+			(struct fuse_bank0_regs *)bank->fuse_regs;
+
+	reg = readl(&fuse_bank0->cfg3);
+	if (((reg >> 16) & 0x3) == 0x3) {
+		if (ldo_bypass) {
+			printf("Wrong dtb file used! i.MX6Q@1.2Ghz only "
+				"works with ldo-enable mode!\n");
+			/*
+			 * Currently, only imx6q-sabresd board might be here,
+			 * since only i.MX6Q support 1.2G and only Sabresd board
+			 * support ldo-bypass mode. So hardcode here.
+			 * You can also modify your board(i.MX6Q) dtb name if it
+			 * supports both ldo-bypass and ldo-enable mode.
+			 */
+			printf("Please use imx6q-sabresd-ldo.dtb!\n");
+			hang();
+		}
+		result = 1;
+	}
+
+	return result;
+}
+
+static int arm_orig_podf;
+void set_arm_freq_400M(bool is_400M)
+{
+	struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
+
+	if (is_400M)
+		writel(0x1, &mxc_ccm->cacrr);
+	else
+		writel(arm_orig_podf, &mxc_ccm->cacrr);
+}
+
+void prep_anatop_bypass(void)
+{
+	struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
+
+	arm_orig_podf = readl(&mxc_ccm->cacrr);
+	/*
+	 * Downgrade ARM speed to 400Mhz as half of boot 800Mhz before ldo
+	 * bypassed, also downgrade internal vddarm ldo to 0.975V.
+	 * VDDARM_IN 0.975V + 125mV = 1.1V < Max(1.3V)
+	 * otherwise at 800Mhz(i.mx6dl):
+	 * VDDARM_IN 1.175V + 125mV = 1.3V = Max(1.3V)
+	 * We need provide enough gap in this case.
+	 * skip if boot from 400M.
+	 */
+	if (!arm_orig_podf)
+		set_arm_freq_400M(true);
+#if !defined(CONFIG_MX6DL) && !defined(CONFIG_MX6SX)
+	set_ldo_voltage(LDO_ARM, 975);
+#else
+	set_ldo_voltage(LDO_ARM, 1150);
+#endif
+}
+
+void set_wdog_reset(struct wdog_regs *wdog)
+{
+	u32 reg = readw(&wdog->wcr);
+	/*
+	 * use WDOG_B mode to reset external pmic because it's risky for the
+	 * following watchdog reboot in case of cpu freq at lowest 400Mhz with
+	 * ldo-bypass mode. Because boot frequency maybe higher 800Mhz i.e. So
+	 * in ldo-bypass mode watchdog reset will only triger POR reset, not
+	 * WDOG reset. But below code depends on hardware design, if HW didn't
+	 * connect WDOG_B pin to external pmic such as i.mx6slevk, we can skip
+	 * these code since it assumed boot from 400Mhz always.
+	 */
+	reg = readw(&wdog->wcr);
+	reg |= 1 << 3;
+	/*
+	 * WDZST bit is write-once only bit. Align this bit in kernel,
+	 * otherwise kernel code will have no chance to set this bit.
+	 */
+	reg |= 1 << 0;
+	writew(reg, &wdog->wcr);
+}
+
+int set_anatop_bypass(int wdog_reset_pin)
+{
+	struct anatop_regs *anatop= (struct anatop_regs*)ANATOP_BASE_ADDR;
+	struct wdog_regs *wdog;
+	u32 reg = readl(&anatop->reg_core);
+
+	/* bypass VDDARM/VDDSOC */
+	reg = reg | (0x1F << 18) | 0x1F;
+	writel(reg, &anatop->reg_core);
+
+	if (wdog_reset_pin == 2)
+		wdog = (struct wdog_regs *) WDOG2_BASE_ADDR;
+	else if (wdog_reset_pin == 1)
+		wdog = (struct wdog_regs *) WDOG1_BASE_ADDR;
+	else
+		return arm_orig_podf;
+	set_wdog_reset(wdog);
+	return arm_orig_podf;
+}
+
+void finish_anatop_bypass(void)
+{
+	if (!arm_orig_podf)
+		set_arm_freq_400M(false);
+}
+#endif
+
 #ifdef CONFIG_IMX_HDMI
 void imx_enable_hdmi_phy(void)
 {
diff --git a/arch/arm/imx-common/cpu.c b/arch/arm/imx-common/cpu.c
index 067d08f..67c4197 100644
--- a/arch/arm/imx-common/cpu.c
+++ b/arch/arm/imx-common/cpu.c
@@ -218,6 +218,9 @@ void arch_preboot_os(void)
 	disable_sata_clock();
 #endif
 #endif
+#if defined(CONFIG_LDO_BYPASS_CHECK)
+	ldo_mode_set(check_ldo_bypass());
+#endif
 #if defined(CONFIG_VIDEO_IPUV3)
 	/* disable video before launching O/S */
 	ipuv3_fb_shutdown();
diff --git a/arch/arm/include/asm/arch-mx6/sys_proto.h b/arch/arm/include/asm/arch-mx6/sys_proto.h
index 28ba844..10bab2b 100644
--- a/arch/arm/include/asm/arch-mx6/sys_proto.h
+++ b/arch/arm/include/asm/arch-mx6/sys_proto.h
@@ -27,6 +27,16 @@ u32 get_cpu_rev(void);
 const char *get_imx_type(u32 imxtype);
 unsigned imx_ddr_size(void);
 void set_chipselect_size(int const);
+void set_wdog_reset(struct wdog_regs *wdog);
+
+#ifdef CONFIG_LDO_BYPASS_CHECK
+int check_ldo_bypass(void);
+int check_1_2G(void);
+int set_anatop_bypass(int wdog_reset_pin);
+void ldo_mode_set(int ldo_bypass);
+void prep_anatop_bypass(void);
+void finish_anatop_bypass(void);
+#endif
 
 /*
  * Initializes on-chip ethernet controllers.