diff options
Diffstat (limited to 'arch/arm/include/asm/arch-kirkwood/config.h')
| -rw-r--r-- | arch/arm/include/asm/arch-kirkwood/config.h | 138 |
1 files changed, 0 insertions, 138 deletions
diff --git a/arch/arm/include/asm/arch-kirkwood/config.h b/arch/arm/include/asm/arch-kirkwood/config.h deleted file mode 100644 index e77ac40..0000000 --- a/arch/arm/include/asm/arch-kirkwood/config.h +++ /dev/null @@ -1,138 +0,0 @@ -/* - * (C) Copyright 2011 - * Marvell Semiconductor <www.marvell.com> - * Written-by: Lei Wen <leiwen@marvell.com> - * - * SPDX-License-Identifier: GPL-2.0+ - */ - -/* - * This file should be included in board config header file. - * - * It supports common definitions for Kirkwood platform - */ - -#ifndef _KW_CONFIG_H -#define _KW_CONFIG_H - -#if defined (CONFIG_KW88F6281) -#include <asm/arch/kw88f6281.h> -#elif defined (CONFIG_KW88F6192) -#include <asm/arch/kw88f6192.h> -#else -#error "SOC Name not defined" -#endif /* CONFIG_KW88F6281 */ - -#include <asm/arch/soc.h> -#define CONFIG_SYS_CACHELINE_SIZE 32 - /* default Dcache Line length for kirkwood */ -#define CONFIG_MD5 /* get_random_hex on krikwood needs MD5 support */ -#define CONFIG_KIRKWOOD_EGIGA_INIT /* Enable GbePort0/1 for kernel */ -#define CONFIG_KIRKWOOD_RGMII_PAD_1V8 /* Set RGMII Pad voltage to 1.8V */ -#define CONFIG_KIRKWOOD_PCIE_INIT /* Enable PCIE Port0 for kernel */ - -/* - * By default kwbimage.cfg from board specific folder is used - * If for some board, different configuration file need to be used, - * CONFIG_SYS_KWD_CONFIG should be defined in board specific header file - */ -#ifndef CONFIG_SYS_KWD_CONFIG -#define CONFIG_SYS_KWD_CONFIG $(CONFIG_BOARDDIR)/kwbimage.cfg -#endif /* CONFIG_SYS_KWD_CONFIG */ - -/* Kirkwood has 2k of Security SRAM, use it for SP */ -#define CONFIG_SYS_INIT_SP_ADDR 0xC8012000 -#define CONFIG_NR_DRAM_BANKS_MAX 2 - -#define CONFIG_I2C_MVTWSI_BASE KW_TWSI_BASE -#define MV_UART_CONSOLE_BASE KW_UART0_BASE -#define MV_SATA_BASE KW_SATA_BASE -#define MV_SATA_PORT0_OFFSET KW_SATA_PORT0_OFFSET -#define MV_SATA_PORT1_OFFSET KW_SATA_PORT1_OFFSET - -/* - * NAND configuration - */ -#ifdef CONFIG_CMD_NAND -#define CONFIG_NAND_KIRKWOOD -#define CONFIG_SYS_NAND_BASE 0xD8000000 /* MV_DEFADR_NANDF */ -#define NAND_ALLOW_ERASE_ALL 1 -#endif - -/* - * SPI Flash configuration - */ -#ifdef CONFIG_CMD_SF -#define CONFIG_HARD_SPI 1 -#define CONFIG_KIRKWOOD_SPI 1 -#ifndef CONFIG_ENV_SPI_BUS -# define CONFIG_ENV_SPI_BUS 0 -#endif -#ifndef CONFIG_ENV_SPI_CS -# define CONFIG_ENV_SPI_CS 0 -#endif -#ifndef CONFIG_ENV_SPI_MAX_HZ -# define CONFIG_ENV_SPI_MAX_HZ 50000000 -#endif -#endif - -/* - * Ethernet Driver configuration - */ -#ifdef CONFIG_CMD_NET -#define CONFIG_CMD_MII -#define CONFIG_NETCONSOLE /* include NetConsole support */ -#define CONFIG_MII /* expose smi ove miiphy interface */ -#define CONFIG_MVGBE /* Enable Marvell Gbe Controller Driver */ -#define CONFIG_SYS_FAULT_ECHO_LINK_DOWN /* detect link using phy */ -#define CONFIG_ENV_OVERWRITE /* ethaddr can be reprogrammed */ -#define CONFIG_RESET_PHY_R /* use reset_phy() to init mv8831116 PHY */ -#endif /* CONFIG_CMD_NET */ - -/* - * USB/EHCI - */ -#ifdef CONFIG_CMD_USB -#define CONFIG_USB_EHCI_MARVELL -#define CONFIG_EHCI_IS_TDI -#endif /* CONFIG_CMD_USB */ - -/* - * IDE Support on SATA ports - */ -#ifdef CONFIG_CMD_IDE -#define __io -#define CONFIG_CMD_EXT2 -#define CONFIG_MVSATA_IDE -#define CONFIG_IDE_PREINIT -#define CONFIG_MVSATA_IDE_USE_PORT1 -/* Needs byte-swapping for ATA data register */ -#define CONFIG_IDE_SWAP_IO -/* Data, registers and alternate blocks are at the same offset */ -#define CONFIG_SYS_ATA_DATA_OFFSET (0x0100) -#define CONFIG_SYS_ATA_REG_OFFSET (0x0100) -#define CONFIG_SYS_ATA_ALT_OFFSET (0x0100) -/* Each 8-bit ATA register is aligned to a 4-bytes address */ -#define CONFIG_SYS_ATA_STRIDE 4 -/* Controller supports 48-bits LBA addressing */ -#define CONFIG_LBA48 -/* CONFIG_CMD_IDE requires some #defines for ATA registers */ -#define CONFIG_SYS_IDE_MAXBUS 2 -#define CONFIG_SYS_IDE_MAXDEVICE 2 -/* ATA registers base is at SATA controller base */ -#define CONFIG_SYS_ATA_BASE_ADDR MV_SATA_BASE -#endif /* CONFIG_CMD_IDE */ - -/* - * I2C related stuff - */ -#ifdef CONFIG_CMD_I2C -#ifndef CONFIG_SYS_I2C_SOFT -#define CONFIG_SYS_I2C -#define CONFIG_SYS_I2C_MVTWSI -#endif -#define CONFIG_SYS_I2C_SLAVE 0x0 -#define CONFIG_SYS_I2C_SPEED 100000 -#endif - -#endif /* _KW_CONFIG_H */ |