diff options
Diffstat (limited to 'arch/arm/cpu/arm926ejs/davinci/da850_lowlevel.c')
| -rw-r--r-- | arch/arm/cpu/arm926ejs/davinci/da850_lowlevel.c | 313 |
1 files changed, 0 insertions, 313 deletions
diff --git a/arch/arm/cpu/arm926ejs/davinci/da850_lowlevel.c b/arch/arm/cpu/arm926ejs/davinci/da850_lowlevel.c deleted file mode 100644 index 19730ce..0000000 --- a/arch/arm/cpu/arm926ejs/davinci/da850_lowlevel.c +++ /dev/null @@ -1,313 +0,0 @@ -/* - * SoC-specific lowlevel code for DA850 - * - * Copyright (C) 2011 - * Heiko Schocher, DENX Software Engineering, hs@denx.de. - * - * SPDX-License-Identifier: GPL-2.0+ - */ -#include <common.h> -#include <nand.h> -#include <ns16550.h> -#include <post.h> -#include <asm/arch/da850_lowlevel.h> -#include <asm/arch/hardware.h> -#include <asm/arch/davinci_misc.h> -#include <asm/arch/ddr2_defs.h> -#include <asm/ti-common/davinci_nand.h> -#include <asm/arch/pll_defs.h> - -void davinci_enable_uart0(void) -{ - lpsc_on(DAVINCI_LPSC_UART0); - - /* Bringup UART0 out of reset */ - REG(UART0_PWREMU_MGMT) = 0x00006001; -} - -#if defined(CONFIG_SYS_DA850_PLL_INIT) -static void da850_waitloop(unsigned long loopcnt) -{ - unsigned long i; - - for (i = 0; i < loopcnt; i++) - asm(" NOP"); -} - -static int da850_pll_init(struct davinci_pllc_regs *reg, unsigned long pllmult) -{ - if (reg == davinci_pllc0_regs) - /* Unlock PLL registers. */ - clrbits_le32(&davinci_syscfg_regs->cfgchip0, PLL_MASTER_LOCK); - - /* - * Set PLLENSRC '0',bit 5, PLL Enable(PLLEN) selection is controlled - * through MMR - */ - clrbits_le32(®->pllctl, PLLCTL_PLLENSRC); - /* PLLCTL.EXTCLKSRC bit 9 should be left at 0 for Freon */ - clrbits_le32(®->pllctl, PLLCTL_EXTCLKSRC); - - /* Set PLLEN=0 => PLL BYPASS MODE */ - clrbits_le32(®->pllctl, PLLCTL_PLLEN); - - da850_waitloop(150); - - if (reg == davinci_pllc0_regs) { - /* - * Select the Clock Mode bit 8 as External Clock or On Chip - * Oscilator - */ - dv_maskbits(®->pllctl, ~PLLCTL_RES_9); - setbits_le32(®->pllctl, - (CONFIG_SYS_DV_CLKMODE << PLLCTL_CLOCK_MODE_SHIFT)); - } - - /* Clear PLLRST bit to reset the PLL */ - clrbits_le32(®->pllctl, PLLCTL_PLLRST); - - /* Disable the PLL output */ - setbits_le32(®->pllctl, PLLCTL_PLLDIS); - - /* PLL initialization sequence */ - /* - * Power up the PLL- PWRDN bit set to 0 to bring the PLL out of - * power down bit - */ - clrbits_le32(®->pllctl, PLLCTL_PLLPWRDN); - - /* Enable the PLL from Disable Mode PLLDIS bit to 0 */ - clrbits_le32(®->pllctl, PLLCTL_PLLDIS); - -#if defined(CONFIG_SYS_DA850_PLL0_PREDIV) - /* program the prediv */ - if (reg == davinci_pllc0_regs && CONFIG_SYS_DA850_PLL0_PREDIV) - writel((PLL_DIVEN | CONFIG_SYS_DA850_PLL0_PREDIV), - ®->prediv); -#endif - - /* Program the required multiplier value in PLLM */ - writel(pllmult, ®->pllm); - - /* program the postdiv */ - if (reg == davinci_pllc0_regs) - writel((PLL_POSTDEN | CONFIG_SYS_DA850_PLL0_POSTDIV), - ®->postdiv); - else - writel((PLL_POSTDEN | CONFIG_SYS_DA850_PLL1_POSTDIV), - ®->postdiv); - - /* - * Check for the GOSTAT bit in PLLSTAT to clear to 0 to indicate that - * no GO operation is currently in progress - */ - while ((readl(®->pllstat) & PLLCMD_GOSTAT) == PLLCMD_GOSTAT) - ; - - if (reg == davinci_pllc0_regs) { - writel(CONFIG_SYS_DA850_PLL0_PLLDIV1, ®->plldiv1); - writel(CONFIG_SYS_DA850_PLL0_PLLDIV2, ®->plldiv2); - writel(CONFIG_SYS_DA850_PLL0_PLLDIV3, ®->plldiv3); - writel(CONFIG_SYS_DA850_PLL0_PLLDIV4, ®->plldiv4); - writel(CONFIG_SYS_DA850_PLL0_PLLDIV5, ®->plldiv5); - writel(CONFIG_SYS_DA850_PLL0_PLLDIV6, ®->plldiv6); - writel(CONFIG_SYS_DA850_PLL0_PLLDIV7, ®->plldiv7); - } else { - writel(CONFIG_SYS_DA850_PLL1_PLLDIV1, ®->plldiv1); - writel(CONFIG_SYS_DA850_PLL1_PLLDIV2, ®->plldiv2); - writel(CONFIG_SYS_DA850_PLL1_PLLDIV3, ®->plldiv3); - } - - /* - * Set the GOSET bit in PLLCMD to 1 to initiate a new divider - * transition. - */ - setbits_le32(®->pllcmd, PLLCMD_GOSTAT); - - /* - * Wait for the GOSTAT bit in PLLSTAT to clear to 0 - * (completion of phase alignment). - */ - while ((readl(®->pllstat) & PLLCMD_GOSTAT) == PLLCMD_GOSTAT) - ; - - /* Wait for PLL to reset properly. See PLL spec for PLL reset time */ - da850_waitloop(200); - - /* Set the PLLRST bit in PLLCTL to 1 to bring the PLL out of reset */ - setbits_le32(®->pllctl, PLLCTL_PLLRST); - - /* Wait for PLL to lock. See PLL spec for PLL lock time */ - da850_waitloop(2400); - - /* - * Set the PLLEN bit in PLLCTL to 1 to remove the PLL from bypass - * mode - */ - setbits_le32(®->pllctl, PLLCTL_PLLEN); - - - /* - * clear EMIFA and EMIFB clock source settings, let them - * run off SYSCLK - */ - if (reg == davinci_pllc0_regs) - dv_maskbits(&davinci_syscfg_regs->cfgchip3, - ~(PLL_SCSCFG3_DIV45PENA | PLL_SCSCFG3_EMA_CLKSRC)); - - return 0; -} -#endif /* CONFIG_SYS_DA850_PLL_INIT */ - -#if defined(CONFIG_SYS_DA850_DDR_INIT) -static int da850_ddr_setup(void) -{ - unsigned long tmp; - - /* Enable the Clock to DDR2/mDDR */ - lpsc_on(DAVINCI_LPSC_DDR_EMIF); - - tmp = readl(&davinci_syscfg1_regs->vtpio_ctl); - if ((tmp & VTP_POWERDWN) == VTP_POWERDWN) { - /* Begin VTP Calibration */ - clrbits_le32(&davinci_syscfg1_regs->vtpio_ctl, VTP_POWERDWN); - clrbits_le32(&davinci_syscfg1_regs->vtpio_ctl, VTP_LOCK); - setbits_le32(&davinci_syscfg1_regs->vtpio_ctl, VTP_CLKRZ); - clrbits_le32(&davinci_syscfg1_regs->vtpio_ctl, VTP_CLKRZ); - setbits_le32(&davinci_syscfg1_regs->vtpio_ctl, VTP_CLKRZ); - - /* Polling READY bit to see when VTP calibration is done */ - tmp = readl(&davinci_syscfg1_regs->vtpio_ctl); - while ((tmp & VTP_READY) != VTP_READY) - tmp = readl(&davinci_syscfg1_regs->vtpio_ctl); - - setbits_le32(&davinci_syscfg1_regs->vtpio_ctl, VTP_LOCK); - setbits_le32(&davinci_syscfg1_regs->vtpio_ctl, VTP_POWERDWN); - } - setbits_le32(&davinci_syscfg1_regs->vtpio_ctl, VTP_IOPWRDWN); - writel(CONFIG_SYS_DA850_DDR2_DDRPHYCR, &dv_ddr2_regs_ctrl->ddrphycr); - - if (CONFIG_SYS_DA850_DDR2_SDBCR & (1 << DV_DDR_SDCR_DDR2EN_SHIFT)) { - /* DDR2 */ - clrbits_le32(&davinci_syscfg1_regs->ddr_slew, - (1 << DDR_SLEW_DDR_PDENA_BIT) | - (1 << DDR_SLEW_CMOSEN_BIT)); - } else { - /* MOBILE DDR */ - setbits_le32(&davinci_syscfg1_regs->ddr_slew, - (1 << DDR_SLEW_DDR_PDENA_BIT) | - (1 << DDR_SLEW_CMOSEN_BIT)); - } - - /* - * SDRAM Configuration Register (SDCR): - * First set the BOOTUNLOCK bit to make configuration bits - * writeable. - */ - setbits_le32(&dv_ddr2_regs_ctrl->sdbcr, DV_DDR_BOOTUNLOCK); - - /* - * Write the new value of these bits and clear BOOTUNLOCK. - * At the same time, set the TIMUNLOCK bit to allow changing - * the timing registers - */ - tmp = CONFIG_SYS_DA850_DDR2_SDBCR; - tmp &= ~DV_DDR_BOOTUNLOCK; - tmp |= DV_DDR_TIMUNLOCK; - writel(tmp, &dv_ddr2_regs_ctrl->sdbcr); - - /* write memory configuration and timing */ - if (!(CONFIG_SYS_DA850_DDR2_SDBCR & (1 << DV_DDR_SDCR_DDR2EN_SHIFT))) { - /* MOBILE DDR only*/ - writel(CONFIG_SYS_DA850_DDR2_SDBCR2, - &dv_ddr2_regs_ctrl->sdbcr2); - } - writel(CONFIG_SYS_DA850_DDR2_SDTIMR, &dv_ddr2_regs_ctrl->sdtimr); - writel(CONFIG_SYS_DA850_DDR2_SDTIMR2, &dv_ddr2_regs_ctrl->sdtimr2); - - /* clear the TIMUNLOCK bit and write the value of the CL field */ - tmp &= ~DV_DDR_TIMUNLOCK; - writel(tmp, &dv_ddr2_regs_ctrl->sdbcr); - - /* - * LPMODEN and MCLKSTOPEN must be set! - * Without this bits set, PSC don;t switch states !! - */ - writel(CONFIG_SYS_DA850_DDR2_SDRCR | - (1 << DV_DDR_SRCR_LPMODEN_SHIFT) | - (1 << DV_DDR_SRCR_MCLKSTOPEN_SHIFT), - &dv_ddr2_regs_ctrl->sdrcr); - - /* SyncReset the Clock to EMIF3A SDRAM */ - lpsc_syncreset(DAVINCI_LPSC_DDR_EMIF); - /* Enable the Clock to EMIF3A SDRAM */ - lpsc_on(DAVINCI_LPSC_DDR_EMIF); - - /* disable self refresh */ - clrbits_le32(&dv_ddr2_regs_ctrl->sdrcr, - DV_DDR_SDRCR_LPMODEN | DV_DDR_SDRCR_MCLKSTOPEN); - writel(CONFIG_SYS_DA850_DDR2_PBBPR, &dv_ddr2_regs_ctrl->pbbpr); - - return 0; -} -#endif /* CONFIG_SYS_DA850_DDR_INIT */ - -__attribute__((weak)) -void board_gpio_init(void) -{ - return; -} - -int arch_cpu_init(void) -{ - /* Unlock kick registers */ - writel(DV_SYSCFG_KICK0_UNLOCK, &davinci_syscfg_regs->kick0); - writel(DV_SYSCFG_KICK1_UNLOCK, &davinci_syscfg_regs->kick1); - - dv_maskbits(&davinci_syscfg_regs->suspsrc, - CONFIG_SYS_DA850_SYSCFG_SUSPSRC); - - /* configure pinmux settings */ - if (davinci_configure_pin_mux_items(pinmuxes, pinmuxes_size)) - return 1; - -#if defined(CONFIG_SYS_DA850_PLL_INIT) - /* PLL setup */ - da850_pll_init(davinci_pllc0_regs, CONFIG_SYS_DA850_PLL0_PLLM); - da850_pll_init(davinci_pllc1_regs, CONFIG_SYS_DA850_PLL1_PLLM); -#endif - /* setup CSn config */ -#if defined(CONFIG_SYS_DA850_CS2CFG) - writel(CONFIG_SYS_DA850_CS2CFG, &davinci_emif_regs->ab1cr); -#endif -#if defined(CONFIG_SYS_DA850_CS3CFG) - writel(CONFIG_SYS_DA850_CS3CFG, &davinci_emif_regs->ab2cr); -#endif - - da8xx_configure_lpsc_items(lpsc, lpsc_size); - - /* GPIO setup */ - board_gpio_init(); - - - NS16550_init((NS16550_t)(CONFIG_SYS_NS16550_COM1), - CONFIG_SYS_NS16550_CLK / 16 / CONFIG_BAUDRATE); - - /* - * Fix Power and Emulation Management Register - * see sprufw3a.pdf page 37 Table 24 - */ - writel((DAVINCI_UART_PWREMU_MGMT_FREE | DAVINCI_UART_PWREMU_MGMT_URRST | - DAVINCI_UART_PWREMU_MGMT_UTRST), -#if (CONFIG_SYS_NS16550_COM1 == DAVINCI_UART0_BASE) - &davinci_uart0_ctrl_regs->pwremu_mgmt); -#else - &davinci_uart2_ctrl_regs->pwremu_mgmt); -#endif - -#if defined(CONFIG_SYS_DA850_DDR_INIT) - da850_ddr_setup(); -#endif - - return 0; -} |