diff options
| -rw-r--r-- | board/freescale/mpc8308rdb/mpc8308rdb.c | 49 | ||||
| -rw-r--r-- | include/configs/MPC8308RDB.h | 13 |
2 files changed, 62 insertions, 0 deletions
diff --git a/board/freescale/mpc8308rdb/mpc8308rdb.c b/board/freescale/mpc8308rdb/mpc8308rdb.c index 5c54357..b97cdc1 100644 --- a/board/freescale/mpc8308rdb/mpc8308rdb.c +++ b/board/freescale/mpc8308rdb/mpc8308rdb.c @@ -24,6 +24,7 @@ #include <common.h> #include <hwconfig.h> #include <i2c.h> +#include <spi.h> #include <libfdt.h> #include <fdt_support.h> #include <pci.h> @@ -36,6 +37,35 @@ DECLARE_GLOBAL_DATA_PTR; +/* + * The following are used to control the SPI chip selects for the SPI command. + */ +#ifdef CONFIG_MPC8XXX_SPI + +#define SPI_CS_MASK 0x00400000 + +int spi_cs_is_valid(unsigned int bus, unsigned int cs) +{ + return bus == 0 && cs == 0; +} + +void spi_cs_activate(struct spi_slave *slave) +{ + immap_t *immr = (immap_t *)CONFIG_SYS_IMMR; + + /* active low */ + clrbits_be32(&immr->gpio[0].dat, SPI_CS_MASK); +} + +void spi_cs_deactivate(struct spi_slave *slave) +{ + immap_t *immr = (immap_t *)CONFIG_SYS_IMMR; + + /* inactive high */ + setbits_be32(&immr->gpio[0].dat, SPI_CS_MASK); +} +#endif /* CONFIG_MPC8XXX_SPI */ + static u8 read_board_info(void) { u8 val8; @@ -109,6 +139,25 @@ void pci_init_board(void) */ int misc_init_r(void) { +#ifdef CONFIG_MPC8XXX_SPI + immap_t *immr = (immap_t *)CONFIG_SYS_IMMR; + sysconf83xx_t *sysconf = &immr->sysconf; + + /* + * Set proper bits in SICRH to allow SPI on header J8 + * + * NOTE: this breaks the TSEC2 interface, attached to the Vitesse + * switch. The pinmux configuration does not have a fine enough + * granularity to support both simultaneously. + */ + clrsetbits_be32(&sysconf->sicrh, SICRH_GPIO_A_TSEC2, SICRH_GPIO_A_GPIO); + puts("WARNING: SPI enabled, TSEC2 support is broken\n"); + + /* Set header J8 SPI chip select output, disabled */ + setbits_be32(&immr->gpio[0].dir, SPI_CS_MASK); + setbits_be32(&immr->gpio[0].dat, SPI_CS_MASK); +#endif + #ifdef CONFIG_VSC7385_IMAGE if (vsc7385_upload_firmware((void *) CONFIG_VSC7385_IMAGE, CONFIG_VSC7385_IMAGE_SIZE)) { diff --git a/include/configs/MPC8308RDB.h b/include/configs/MPC8308RDB.h index 7f2761c..a24538a 100644 --- a/include/configs/MPC8308RDB.h +++ b/include/configs/MPC8308RDB.h @@ -340,6 +340,19 @@ #define CONFIG_SYS_I2C_OFFSET 0x3000 #define CONFIG_SYS_I2C2_OFFSET 0x3100 +/* + * SPI on header J8 + * + * WARNING: enabling this will break TSEC2 (connected to the Vitesse switch) + * due to a pinmux conflict between GPIO9 (SPI chip select )and the TSEC2 pins. + */ +#ifdef CONFIG_MPC8XXX_SPI +#define CONFIG_CMD_SPI +#define CONFIG_USE_SPIFLASH +#define CONFIG_SPI_FLASH +#define CONFIG_SPI_FLASH_SPANSION +#define CONFIG_CMD_SF +#endif /* * Board info - revision and where boot from |