diff options
| -rw-r--r-- | arch/arm/include/asm/arch-armada100/armada100.h | 19 | ||||
| -rw-r--r-- | arch/arm/include/asm/arch-armada100/mfp.h | 6 | ||||
| -rw-r--r-- | board/Marvell/gplugd/gplugd.c | 12 | ||||
| -rw-r--r-- | include/configs/gplugd.h | 5 |
4 files changed, 42 insertions, 0 deletions
diff --git a/arch/arm/include/asm/arch-armada100/armada100.h b/arch/arm/include/asm/arch-armada100/armada100.h index c449d4e..a8181b6 100644 --- a/arch/arm/include/asm/arch-armada100/armada100.h +++ b/arch/arm/include/asm/arch-armada100/armada100.h @@ -45,6 +45,10 @@ #define FE_CLK_RST 0x1 #define FE_CLK_ENA 0x8 +/* SSP2 Clock Control */ +#define SSP2_APBCLK 0x01 +#define SSP2_FNCLK 0x02 + /* Register Base Addresses */ #define ARMD1_DRAM_BASE 0xB0000000 #define ARMD1_FEC_BASE 0xC0800000 @@ -175,5 +179,20 @@ struct armd1apb1_registers { u32 ac97; /*0x084*/ }; +/* +* APB2 Clock Reset/Control Registers +* Refer Datasheet Appendix A.11 +*/ +struct armd1apb2_registers { + u32 pad1[0x01C - 0x000]; + u32 ssp1_clkrst; /* 0x01C */ + u32 ssp2_clkrst; /* 0x020 */ + u32 pad2[0x04C - 0x020 - 4]; + u32 ssp3_clkrst; /* 0x04C */ + u32 pad3[0x058 - 0x04C - 4]; + u32 ssp4_clkrst; /* 0x058 */ + u32 ssp5_clkrst; /* 0x05C */ +}; + #endif /* CONFIG_ARMADA100 */ #endif /* _ASM_ARCH_ARMADA100_H */ diff --git a/arch/arm/include/asm/arch-armada100/mfp.h b/arch/arm/include/asm/arch-armada100/mfp.h index da76b58..d48251a 100644 --- a/arch/arm/include/asm/arch-armada100/mfp.h +++ b/arch/arm/include/asm/arch-armada100/mfp.h @@ -83,6 +83,12 @@ #define MFP101_ETH_MDIO (MFP_REG(0x194) | MFP_AF5 | MFP_DRIVE_MEDIUM) #define MFP103_ETH_RXDV (MFP_REG(0x19C) | MFP_AF5 | MFP_DRIVE_MEDIUM) +/* SPI */ +#define MFP107_SSP2_RXD (MFP_REG(0x1AC) | MFP_AF4 | MFP_DRIVE_MEDIUM) +#define MFP108_SSP2_TXD (MFP_REG(0x1B0) | MFP_AF4 | MFP_DRIVE_MEDIUM) +#define MFP110_SSP2_CS (MFP_REG(0x1B8) | MFP_AF0 | MFP_DRIVE_MEDIUM) +#define MFP111_SSP2_CLK (MFP_REG(0x1BC) | MFP_AF4 | MFP_DRIVE_MEDIUM) + /* More macros can be defined here... */ #define MFP_PIN_MAX 117 diff --git a/board/Marvell/gplugd/gplugd.c b/board/Marvell/gplugd/gplugd.c index b4f7f81..42c8389 100644 --- a/board/Marvell/gplugd/gplugd.c +++ b/board/Marvell/gplugd/gplugd.c @@ -72,6 +72,12 @@ int board_early_init_f(void) MFP101_ETH_MDIO, MFP103_ETH_RXDV, + /* SSP2 */ + MFP107_SSP2_RXD, + MFP108_SSP2_TXD, + MFP110_SSP2_CS, + MFP111_SSP2_CLK, + MFP_EOC /*End of configuration*/ }; /* configure MFP's */ @@ -81,6 +87,9 @@ int board_early_init_f(void) int board_init(void) { + struct armd1apb2_registers *apb2_regs = + (struct armd1apb2_registers *)ARMD1_APBC2_BASE; + /* arch number of Board */ gd->bd->bi_arch_number = MACH_TYPE_SHEEVAD; /* adress of boot parameters */ @@ -90,6 +99,9 @@ int board_init(void) udelay(10); /* Deassert PHY_RST# */ gpio_set_value(CONFIG_SYS_GPIO_PHY_RST, GPIO_HIGH); + + /* Enable SSP2 clock */ + writel(SSP2_APBCLK | SSP2_FNCLK, &apb2_regs->ssp2_clkrst); return 0; } diff --git a/include/configs/gplugd.h b/include/configs/gplugd.h index a9f3b3b..6fa724a 100644 --- a/include/configs/gplugd.h +++ b/include/configs/gplugd.h @@ -90,6 +90,11 @@ /* GPIO Configuration for PHY */ #define CONFIG_SYS_GPIO_PHY_RST 104 /* GPIO104 */ +/* SPI Support */ +#define CONFIG_ARMADA100_SPI +#define CONFIG_ENV_SPI_CS 110 +#define CONFIG_SYS_SSP_PORT 2 + /* * mv-common.h should be defined after CMD configs since it used them * to enable certain macros |