summaryrefslogtreecommitdiff
diff options
context:
space:
mode:
-rw-r--r--Makefile19
-rw-r--r--doc/README.sbc834950
-rw-r--r--include/configs/sbc8349.h22
3 files changed, 64 insertions, 27 deletions
diff --git a/Makefile b/Makefile
index 2636ac0..96cca23 100644
--- a/Makefile
+++ b/Makefile
@@ -2380,8 +2380,23 @@ MPC837XERDB_config: unconfig
MVBLM7_config: unconfig
@$(MKCONFIG) $(@:_config=) ppc mpc83xx mvblm7 matrix_vision
-sbc8349_config: unconfig
- @$(MKCONFIG) $(@:_config=) ppc mpc83xx sbc8349
+sbc8349_config \
+sbc8349_PCI_33_config \
+sbc8349_PCI_66_config: unconfig
+ @mkdir -p $(obj)include
+ @if [ "$(findstring _PCI_,$@)" ] ; then \
+ $(XECHO) -n "... PCI HOST at " ; \
+ echo "#define CONFIG_PCI" >>$(obj)include/config.h ; \
+ fi ; \
+ if [ "$(findstring _33_,$@)" ] ; then \
+ $(XECHO) -n "33MHz... " ; \
+ echo "#define PCI_33M" >>$(obj)include/config.h ; \
+ fi ; \
+ if [ "$(findstring _66_,$@)" ] ; then \
+ $(XECHO) -n "66MHz... " ; \
+ echo "#define PCI_66M" >>$(obj)include/config.h ; \
+ fi ;
+ @$(MKCONFIG) -a sbc8349 ppc mpc83xx sbc8349
SIMPC8313_LP_config \
SIMPC8313_SP_config: unconfig
diff --git a/doc/README.sbc8349 b/doc/README.sbc8349
index 908e768..2c35919 100644
--- a/doc/README.sbc8349
+++ b/doc/README.sbc8349
@@ -91,19 +91,37 @@ safety check before resetting the board upon completion of the reflash.
PCI:
====
-This board and U-Boot have been tested with PCI built in, on a SBC8349
-and confirmed that the "pci" command showed the intel e1000 that was
-present in the PCI slot. Note that if a 33MHz 32bit card is inserted
-in the slot, then the whole board will clock down to a 33MHz base
-clock instead of the default 66MHz. This will change the baud clocks
-and mess up your serial console output. If you want to use a 33MHz PCI
-card, then you should build a U-Boot with #undef PCI_66M in the
-include/configs/sbc8349.h and store this to flash prior to powering down
-the board and inserting the 33MHz PCI card.
-
-By default PCI support is disabled to better support very early
-revision MPC834x chips with possible PCI issues. Also PCI support is
-untested on the sbc8347 variants at this point in time.
-
-
- Paul Gortmaker, 01/2007
+There are three configuration choices:
+ sbc8349_config
+ sbc8349_PCI_33_config
+ sbc8349_PCI_66_config
+
+The 1st does not enable CONFIG_PCI, and assumes that the PCI slot
+will be left empty (M66EN high), and so the board will operate with
+a base clock of 66MHz. Note that you need both PCI enabled in u-boot
+and linux in order to have functional PCI under linux. The only
+reason for choosing to not enable PCI would be if you had a very
+early (rev 1.0) CPU with possible PCI issues.
+
+The second enables PCI support and builds for a 33MHz clock rate. Note
+that if a 33MHz 32bit card is inserted in the slot, then the whole board
+will clock down to a 33MHz base clock instead of the default 66MHz. This
+will change the baud clocks and mess up your serial console output if you
+were previously running at 66MHz. If you want to use a 33MHz PCI card,
+then you should build a U-Boot with sbc8349_PCI_33_config and store this
+to flash prior to powering down the board and inserting the 33MHz PCI
+card.
+
+The third option builds PCI support in, and leaves the clocking at the
+default 66MHz. This has been tested with an intel PCI-X e1000 card.
+This is also the appropriate choice for people with a recent (non 1.0)
+CPU who currently have the PCI slot physically empty, but intend to
+possibly add a PCI-X card at a later date.
+
+ => pci
+ Scanning PCI devices on bus 0
+ BusDevFun VendorId DeviceId Device Class Sub-Class
+ _____________________________________________________________
+ 00.00.00 0x1957 0x0080 Processor 0x20
+ 00.11.00 0x8086 0x1026 Network controller 0x00
+ =>
diff --git a/include/configs/sbc8349.h b/include/configs/sbc8349.h
index 868bd54..088b283 100644
--- a/include/configs/sbc8349.h
+++ b/include/configs/sbc8349.h
@@ -40,24 +40,28 @@
#define CONFIG_MPC8349 1 /* MPC8349 specific */
#define CONFIG_SBC8349 1 /* WRS SBC8349 board specific */
-#undef CONFIG_PCI
/* Don't enable PCI2 on sbc834x - it doesn't exist physically. */
#undef CONFIG_MPC83XX_PCI2 /* support for 2nd PCI controller */
-#define PCI_66M
-#ifdef PCI_66M
-#define CONFIG_83XX_CLKIN 66000000 /* in Hz */
-#else
+/*
+ * The default if PCI isn't enabled, or if no PCI clk setting is given
+ * is 66MHz; this is what the board defaults to when the PCI slot is
+ * physically empty. The board will automatically (i.e w/o jumpers)
+ * clock down to 33MHz if you insert a 33MHz PCI card.
+ */
+#ifdef PCI_33M
#define CONFIG_83XX_CLKIN 33000000 /* in Hz */
+#else /* 66M */
+#define CONFIG_83XX_CLKIN 66000000 /* in Hz */
#endif
#ifndef CONFIG_SYS_CLK_FREQ
-#ifdef PCI_66M
-#define CONFIG_SYS_CLK_FREQ 66000000
-#define HRCWL_CSB_TO_CLKIN HRCWL_CSB_TO_CLKIN_4X1
-#else
+#ifdef PCI_33M
#define CONFIG_SYS_CLK_FREQ 33000000
#define HRCWL_CSB_TO_CLKIN HRCWL_CSB_TO_CLKIN_8X1
+#else /* 66M */
+#define CONFIG_SYS_CLK_FREQ 66000000
+#define HRCWL_CSB_TO_CLKIN HRCWL_CSB_TO_CLKIN_4X1
#endif
#endif