summaryrefslogtreecommitdiff
diff options
context:
space:
mode:
-rw-r--r--Makefile8
-rw-r--r--arch/arm/cpu/armv7/am33xx/Makefile1
-rw-r--r--arch/arm/cpu/armv7/am33xx/mem.c98
-rw-r--r--arch/arm/cpu/armv7/am33xx/sys_info.c41
-rw-r--r--arch/arm/cpu/armv7/omap-common/Makefile4
-rw-r--r--arch/arm/cpu/armv7/omap-common/emif-common.c6
-rw-r--r--arch/arm/cpu/armv7/omap-common/hwinit-common.c15
-rw-r--r--arch/arm/cpu/armv7/omap-common/mem-common.c117
-rw-r--r--arch/arm/cpu/armv7/omap3/Makefile1
-rw-r--r--arch/arm/cpu/armv7/omap5/hw_data.c40
-rw-r--r--arch/arm/cpu/armv7/omap5/hwinit.c3
-rw-r--r--arch/arm/cpu/armv7/omap5/prcm-regs.c8
-rw-r--r--arch/arm/cpu/armv7/omap5/sdram.c19
-rw-r--r--arch/arm/cpu/armv7/rmobile/pfc-r8a7791.c2
-rw-r--r--arch/arm/cpu/armv7/zynq/cpu.c13
-rw-r--r--arch/arm/cpu/armv7/zynq/ddrc.c5
-rw-r--r--arch/arm/cpu/armv7/zynq/slcr.c87
-rw-r--r--arch/arm/cpu/armv7/zynq/spl.c15
-rw-r--r--arch/arm/dts/zynq-7000.dtsi194
-rw-r--r--arch/arm/dts/zynq-microzed.dts9
-rw-r--r--arch/arm/dts/zynq-zc702.dts9
-rw-r--r--arch/arm/dts/zynq-zc706.dts9
-rw-r--r--arch/arm/dts/zynq-zc770-xm010.dts9
-rw-r--r--arch/arm/dts/zynq-zc770-xm012.dts9
-rw-r--r--arch/arm/dts/zynq-zc770-xm013.dts9
-rw-r--r--arch/arm/dts/zynq-zed.dts9
-rw-r--r--arch/arm/include/asm/arch-am33xx/sys_proto.h1
-rw-r--r--arch/arm/include/asm/arch-omap3/mem.h1
-rw-r--r--arch/arm/include/asm/arch-omap4/cpu.h5
-rw-r--r--arch/arm/include/asm/arch-omap4/hardware.h26
-rw-r--r--arch/arm/include/asm/arch-omap4/mem.h62
-rw-r--r--arch/arm/include/asm/arch-omap4/omap.h3
-rw-r--r--arch/arm/include/asm/arch-omap4/sys_proto.h51
-rw-r--r--arch/arm/include/asm/arch-omap5/cpu.h5
-rw-r--r--arch/arm/include/asm/arch-omap5/hardware.h26
-rw-r--r--arch/arm/include/asm/arch-omap5/mem.h62
-rw-r--r--arch/arm/include/asm/arch-omap5/omap.h9
-rw-r--r--arch/arm/include/asm/arch-omap5/sys_proto.h50
-rw-r--r--arch/arm/include/asm/arch-rmobile/r8a7790-gpio.h6
-rw-r--r--arch/arm/include/asm/arch-rmobile/r8a7791-gpio.h6
-rw-r--r--arch/arm/include/asm/arch-rmobile/r8a7791.h1
-rw-r--r--arch/arm/include/asm/arch-rmobile/rcar-base.h8
-rw-r--r--arch/arm/include/asm/arch-zynq/hardware.h13
-rw-r--r--arch/arm/include/asm/arch-zynq/sys_proto.h2
-rw-r--r--arch/arm/include/asm/omap_common.h7
-rw-r--r--arch/arm/include/asm/ti-common/sys_proto.h72
-rw-r--r--board/compulab/cm_t54/Makefile10
-rw-r--r--board/compulab/cm_t54/cm_t54.c262
-rw-r--r--board/compulab/cm_t54/mux.c94
-rw-r--r--board/compulab/cm_t54/spl.c66
-rw-r--r--board/compulab/common/Makefile2
-rw-r--r--board/compulab/common/eeprom.c5
-rw-r--r--board/compulab/common/eeprom.h2
-rw-r--r--board/gumstix/duovero/Makefile8
-rw-r--r--board/gumstix/duovero/duovero.c264
-rw-r--r--board/gumstix/duovero/duovero_mux_data.h199
-rw-r--r--board/overo/overo.c43
-rw-r--r--board/overo/overo.h17
-rw-r--r--board/renesas/koelsch/qos.c1
-rw-r--r--board/xilinx/zynq/.gitignore1
-rw-r--r--board/xilinx/zynq/Makefile5
-rw-r--r--board/xilinx/zynq/board.c25
-rw-r--r--board/xilinx/zynq/ps7_init.c12
-rw-r--r--board/xilinx/zynq/xil_io.h13
-rw-r--r--boards.cfg2
-rw-r--r--drivers/usb/host/Makefile1
-rw-r--r--drivers/usb/host/ehci-zynq.c104
-rw-r--r--include/configs/armadillo-800eva.h1
-rw-r--r--include/configs/cm_t54.h149
-rw-r--r--include/configs/duovero.h62
-rw-r--r--include/configs/koelsch.h23
-rw-r--r--include/configs/lager.h22
-rw-r--r--include/configs/omap3_overo.h296
-rw-r--r--include/configs/siemens-am33x-common.h2
-rw-r--r--include/configs/ti_omap4_common.h9
-rw-r--r--include/configs/zynq-common.h52
-rw-r--r--include/configs/zynq_zc70x.h1
-rw-r--r--include/configs/zynq_zed.h1
78 files changed, 2383 insertions, 527 deletions
diff --git a/Makefile b/Makefile
index f2ba48b..928a880 100644
--- a/Makefile
+++ b/Makefile
@@ -753,6 +753,9 @@ ALL-$(CONFIG_SPL) += spl/u-boot-spl.bin
ALL-$(CONFIG_SPL_FRAMEWORK) += u-boot.img
ALL-$(CONFIG_TPL) += tpl/u-boot-tpl.bin
ALL-$(CONFIG_OF_SEPARATE) += u-boot.dtb u-boot-dtb.bin
+ifeq ($(CONFIG_SPL_FRAMEWORK),y)
+ALL-$(CONFIG_OF_SEPARATE) += u-boot-dtb.img
+endif
ALL-$(CONFIG_OF_HOSTFILE) += u-boot.dtb
ifneq ($(CONFIG_SPL_TARGET),)
ALL-$(CONFIG_SPL) += $(CONFIG_SPL_TARGET:"%"=%)
@@ -855,6 +858,11 @@ MKIMAGEFLAGS_u-boot.pbl = -n $(srctree)/$(CONFIG_SYS_FSL_PBL_RCW:"%"=%) \
u-boot.img u-boot.kwb u-boot.pbl: u-boot.bin FORCE
$(call if_changed,mkimage)
+MKIMAGEFLAGS_u-boot-dtb.img = $(MKIMAGEFLAGS_u-boot.img)
+
+u-boot-dtb.img: u-boot-dtb.bin FORCE
+ $(call if_changed,mkimage)
+
u-boot.sha1: u-boot.bin
tools/ubsha1 u-boot.bin
diff --git a/arch/arm/cpu/armv7/am33xx/Makefile b/arch/arm/cpu/armv7/am33xx/Makefile
index 5566310..aae3f09 100644
--- a/arch/arm/cpu/armv7/am33xx/Makefile
+++ b/arch/arm/cpu/armv7/am33xx/Makefile
@@ -14,7 +14,6 @@ endif
obj-$(CONFIG_TI816X) += clock_ti816x.o
obj-y += sys_info.o
-obj-y += mem.o
obj-y += ddr.o
obj-y += emif4.o
obj-y += board.o
diff --git a/arch/arm/cpu/armv7/am33xx/mem.c b/arch/arm/cpu/armv7/am33xx/mem.c
deleted file mode 100644
index 56c9e7d..0000000
--- a/arch/arm/cpu/armv7/am33xx/mem.c
+++ /dev/null
@@ -1,98 +0,0 @@
-/*
- * (C) Copyright 2010
- * Texas Instruments, <www.ti.com>
- *
- * Author :
- * Mansoor Ahamed <mansoor.ahamed@ti.com>
- *
- * Initial Code from:
- * Manikandan Pillai <mani.pillai@ti.com>
- * Richard Woodruff <r-woodruff2@ti.com>
- * Syed Mohammed Khasim <khasim@ti.com>
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-
-#include <common.h>
-#include <asm/io.h>
-#include <asm/arch/cpu.h>
-#include <asm/arch/mem.h>
-#include <asm/arch/sys_proto.h>
-#include <command.h>
-
-struct gpmc *gpmc_cfg;
-
-
-void enable_gpmc_cs_config(const u32 *gpmc_config, struct gpmc_cs *cs, u32 base,
- u32 size)
-{
- writel(0, &cs->config7);
- sdelay(1000);
- /* Delay for settling */
- writel(gpmc_config[0], &cs->config1);
- writel(gpmc_config[1], &cs->config2);
- writel(gpmc_config[2], &cs->config3);
- writel(gpmc_config[3], &cs->config4);
- writel(gpmc_config[4], &cs->config5);
- writel(gpmc_config[5], &cs->config6);
- /* Enable the config */
- writel((((size & 0xF) << 8) | ((base >> 24) & 0x3F) |
- (1 << 6)), &cs->config7);
- sdelay(2000);
-}
-
-/*****************************************************
- * gpmc_init(): init gpmc bus
- * Init GPMC for x16, MuxMode (SDRAM in x32).
- * This code can only be executed from SRAM or SDRAM.
- *****************************************************/
-void gpmc_init(void)
-{
- /* putting a blanket check on GPMC based on ZeBu for now */
- gpmc_cfg = (struct gpmc *)GPMC_BASE;
-#if defined(CONFIG_NOR)
-/* configure GPMC for NOR */
- const u32 gpmc_regs[GPMC_MAX_REG] = { STNOR_GPMC_CONFIG1,
- STNOR_GPMC_CONFIG2,
- STNOR_GPMC_CONFIG3,
- STNOR_GPMC_CONFIG4,
- STNOR_GPMC_CONFIG5,
- STNOR_GPMC_CONFIG6,
- STNOR_GPMC_CONFIG7
- };
- u32 size = GPMC_SIZE_16M;
- u32 base = CONFIG_SYS_FLASH_BASE;
-#elif defined(CONFIG_NAND)
-/* configure GPMC for NAND */
- const u32 gpmc_regs[GPMC_MAX_REG] = { M_NAND_GPMC_CONFIG1,
- M_NAND_GPMC_CONFIG2,
- M_NAND_GPMC_CONFIG3,
- M_NAND_GPMC_CONFIG4,
- M_NAND_GPMC_CONFIG5,
- M_NAND_GPMC_CONFIG6,
- 0
- };
- u32 size = GPMC_SIZE_256M;
- u32 base = CONFIG_SYS_NAND_BASE;
-#else
- const u32 gpmc_regs[GPMC_MAX_REG] = { 0, 0, 0, 0, 0, 0, 0 };
- u32 size = 0;
- u32 base = 0;
-#endif
- /* global settings */
- writel(0x00000008, &gpmc_cfg->sysconfig);
- writel(0x00000000, &gpmc_cfg->irqstatus);
- writel(0x00000000, &gpmc_cfg->irqenable);
-#ifdef CONFIG_NOR
- writel(0x00000200, &gpmc_cfg->config);
-#else
- writel(0x00000012, &gpmc_cfg->config);
-#endif
- /*
- * Disable the GPMC0 config set by ROM code
- */
- writel(0, &gpmc_cfg->cs[0].config7);
- sdelay(1000);
- /* enable chip-select specific configurations */
- enable_gpmc_cs_config(gpmc_regs, &gpmc_cfg->cs[0], base, size);
-}
diff --git a/arch/arm/cpu/armv7/am33xx/sys_info.c b/arch/arm/cpu/armv7/am33xx/sys_info.c
index 50eb598..2ce682f 100644
--- a/arch/arm/cpu/armv7/am33xx/sys_info.c
+++ b/arch/arm/cpu/armv7/am33xx/sys_info.c
@@ -79,12 +79,24 @@ u32 get_sysboot_value(void)
}
#ifdef CONFIG_DISPLAY_CPUINFO
+static char *cpu_revs[] = {
+ "1.0",
+ "2.0",
+ "2.1"};
+
+
+static char *dev_types[] = {
+ "TST",
+ "EMU",
+ "HS",
+ "GP"};
+
/**
* Print CPU information
*/
int print_cpuinfo(void)
{
- char *cpu_s, *sec_s;
+ char *cpu_s, *sec_s, *rev_s;
switch (get_cpu_type()) {
case AM335X:
@@ -94,28 +106,21 @@ int print_cpuinfo(void)
cpu_s = "TI81XX";
break;
default:
- cpu_s = "Unknown cpu type";
+ cpu_s = "Unknown CPU type";
break;
}
- switch (get_device_type()) {
- case TST_DEVICE:
- sec_s = "TST";
- break;
- case EMU_DEVICE:
- sec_s = "EMU";
- break;
- case HS_DEVICE:
- sec_s = "HS";
- break;
- case GP_DEVICE:
- sec_s = "GP";
- break;
- default:
+ if (get_cpu_rev() < ARRAY_SIZE(cpu_revs))
+ rev_s = cpu_revs[get_cpu_rev()];
+ else
+ rev_s = "?";
+
+ if (get_device_type() < ARRAY_SIZE(dev_types))
+ sec_s = dev_types[get_device_type()];
+ else
sec_s = "?";
- }
- printf("%s-%s rev %d\n", cpu_s, sec_s, get_cpu_rev());
+ printf("%s-%s rev %s\n", cpu_s, sec_s, rev_s);
return 0;
}
diff --git a/arch/arm/cpu/armv7/omap-common/Makefile b/arch/arm/cpu/armv7/omap-common/Makefile
index 59f5352..5f5132f 100644
--- a/arch/arm/cpu/armv7/omap-common/Makefile
+++ b/arch/arm/cpu/armv7/omap-common/Makefile
@@ -27,8 +27,4 @@ obj-y += boot-common.o
obj-y += lowlevel_init.o
endif
-ifndef CONFIG_SPL_BUILD
-ifneq ($(CONFIG_OMAP44XX)$(CONFIG_OMAP54XX),)
obj-y += mem-common.o
-endif
-endif
diff --git a/arch/arm/cpu/armv7/omap-common/emif-common.c b/arch/arm/cpu/armv7/omap-common/emif-common.c
index 429c4be..71c0cc8 100644
--- a/arch/arm/cpu/armv7/omap-common/emif-common.c
+++ b/arch/arm/cpu/armv7/omap-common/emif-common.c
@@ -1384,8 +1384,10 @@ void sdram_init(void)
if (sdram_type == EMIF_SDRAM_TYPE_DDR3 &&
(!in_sdram && !warm_reset())) {
- do_bug0039_workaround(EMIF1_BASE);
- do_bug0039_workaround(EMIF2_BASE);
+ if (emif1_enabled)
+ do_bug0039_workaround(EMIF1_BASE);
+ if (emif2_enabled)
+ do_bug0039_workaround(EMIF2_BASE);
}
debug("<<sdram_init()\n");
diff --git a/arch/arm/cpu/armv7/omap-common/hwinit-common.c b/arch/arm/cpu/armv7/omap-common/hwinit-common.c
index 8ebc0ce..ba97d9e 100644
--- a/arch/arm/cpu/armv7/omap-common/hwinit-common.c
+++ b/arch/arm/cpu/armv7/omap-common/hwinit-common.c
@@ -185,7 +185,7 @@ u32 omap_sdram_size(void)
{
u32 section, i, valid;
u64 sdram_start = 0, sdram_end = 0, addr,
- size, total_size = 0, trap_size = 0;
+ size, total_size = 0, trap_size = 0, trap_start = 0;
for (i = 0; i < 4; i++) {
section = __raw_readl(DMM_BASE + i*4);
@@ -194,8 +194,8 @@ u32 omap_sdram_size(void)
addr = section & EMIF_SYS_ADDR_MASK;
/* See if the address is valid */
- if ((addr >= DRAM_ADDR_SPACE_START) &&
- (addr < DRAM_ADDR_SPACE_END)) {
+ if ((addr >= TI_ARMV7_DRAM_ADDR_SPACE_START) &&
+ (addr < TI_ARMV7_DRAM_ADDR_SPACE_END)) {
size = ((section & EMIF_SYS_SIZE_MASK) >>
EMIF_SYS_SIZE_SHIFT);
size = 1 << size;
@@ -208,12 +208,15 @@ u32 omap_sdram_size(void)
sdram_end = addr + size;
} else {
trap_size = size;
+ trap_start = addr;
}
-
}
-
}
- total_size = (sdram_end - sdram_start) - (trap_size);
+
+ if ((trap_start >= sdram_start) && (trap_start < sdram_end))
+ total_size = (sdram_end - sdram_start) - (trap_size);
+ else
+ total_size = sdram_end - sdram_start;
return total_size;
}
diff --git a/arch/arm/cpu/armv7/omap-common/mem-common.c b/arch/arm/cpu/armv7/omap-common/mem-common.c
index afc1bc1..944ef84 100644
--- a/arch/arm/cpu/armv7/omap-common/mem-common.c
+++ b/arch/arm/cpu/armv7/omap-common/mem-common.c
@@ -2,31 +2,136 @@
* (C) Copyright 2010
* Texas Instruments, <www.ti.com>
*
- * Steve Sakoman <steve@sakoman.com>
+ * Author :
+ * Mansoor Ahamed <mansoor.ahamed@ti.com>
+ *
+ * Initial Code from:
+ * Manikandan Pillai <mani.pillai@ti.com>
+ * Richard Woodruff <r-woodruff2@ti.com>
+ * Syed Mohammed Khasim <khasim@ti.com>
*
* SPDX-License-Identifier: GPL-2.0+
*/
+#include <common.h>
+#include <asm/io.h>
#include <asm/arch/cpu.h>
+#include <asm/arch/mem.h>
#include <asm/arch/sys_proto.h>
+#include <command.h>
+#include <linux/mtd/omap_gpmc.h>
struct gpmc *gpmc_cfg;
+#if defined(CONFIG_OMAP34XX)
+/********************************************************
+ * mem_ok() - test used to see if timings are correct
+ * for a part. Helps in guessing which part
+ * we are currently using.
+ *******************************************************/
+u32 mem_ok(u32 cs)
+{
+ u32 val1, val2, addr;
+ u32 pattern = 0x12345678;
+
+ addr = OMAP34XX_SDRC_CS0 + get_sdr_cs_offset(cs);
+
+ writel(0x0, addr + 0x400); /* clear pos A */
+ writel(pattern, addr); /* pattern to pos B */
+ writel(0x0, addr + 4); /* remove pattern off the bus */
+ val1 = readl(addr + 0x400); /* get pos A value */
+ val2 = readl(addr); /* get val2 */
+ writel(0x0, addr + 0x400); /* clear pos A */
+
+ if ((val1 != 0) || (val2 != pattern)) /* see if pos A val changed */
+ return 0;
+ else
+ return 1;
+}
+#endif
+
+void enable_gpmc_cs_config(const u32 *gpmc_config, struct gpmc_cs *cs, u32 base,
+ u32 size)
+{
+ writel(0, &cs->config7);
+ sdelay(1000);
+ /* Delay for settling */
+ writel(gpmc_config[0], &cs->config1);
+ writel(gpmc_config[1], &cs->config2);
+ writel(gpmc_config[2], &cs->config3);
+ writel(gpmc_config[3], &cs->config4);
+ writel(gpmc_config[4], &cs->config5);
+ writel(gpmc_config[5], &cs->config6);
+ /* Enable the config */
+ writel((((size & 0xF) << 8) | ((base >> 24) & 0x3F) |
+ (1 << 6)), &cs->config7);
+ sdelay(2000);
+}
+
/*****************************************************
* gpmc_init(): init gpmc bus
+ * Init GPMC for x16, MuxMode (SDRAM in x32).
* This code can only be executed from SRAM or SDRAM.
*****************************************************/
void gpmc_init(void)
{
+ /* putting a blanket check on GPMC based on ZeBu for now */
gpmc_cfg = (struct gpmc *)GPMC_BASE;
-
+#if defined(CONFIG_NOR)
+/* configure GPMC for NOR */
+ const u32 gpmc_regs[GPMC_MAX_REG] = { STNOR_GPMC_CONFIG1,
+ STNOR_GPMC_CONFIG2,
+ STNOR_GPMC_CONFIG3,
+ STNOR_GPMC_CONFIG4,
+ STNOR_GPMC_CONFIG5,
+ STNOR_GPMC_CONFIG6,
+ STNOR_GPMC_CONFIG7
+ };
+ u32 size = GPMC_SIZE_16M;
+ u32 base = CONFIG_SYS_FLASH_BASE;
+#elif defined(CONFIG_NAND)
+/* configure GPMC for NAND */
+ const u32 gpmc_regs[GPMC_MAX_REG] = { M_NAND_GPMC_CONFIG1,
+ M_NAND_GPMC_CONFIG2,
+ M_NAND_GPMC_CONFIG3,
+ M_NAND_GPMC_CONFIG4,
+ M_NAND_GPMC_CONFIG5,
+ M_NAND_GPMC_CONFIG6,
+ 0
+ };
+ u32 size = GPMC_SIZE_256M;
+ u32 base = CONFIG_SYS_NAND_BASE;
+#elif defined(CONFIG_CMD_ONENAND)
+ const u32 gpmc_regs[GPMC_MAX_REG] = { ONENAND_GPMC_CONFIG1,
+ ONENAND_GPMC_CONFIG2,
+ ONENAND_GPMC_CONFIG3,
+ ONENAND_GPMC_CONFIG4,
+ ONENAND_GPMC_CONFIG5,
+ ONENAND_GPMC_CONFIG6,
+ 0
+ };
+ u32 base = PISMO1_ONEN_BASE;
+ u32 size = PISMO1_ONEN_SIZE;
+#else
+ const u32 gpmc_regs[GPMC_MAX_REG] = { 0, 0, 0, 0, 0, 0, 0 };
+ u32 size = 0;
+ u32 base = 0;
+#endif
/* global settings */
- writel(0, &gpmc_cfg->irqenable); /* isr's sources masked */
- writel(0, &gpmc_cfg->timeout_control);/* timeout disable */
-
+ writel(0x00000008, &gpmc_cfg->sysconfig);
+ writel(0x00000000, &gpmc_cfg->irqstatus);
+ writel(0x00000000, &gpmc_cfg->irqenable);
+ writel(0x00000000, &gpmc_cfg->timeout_control);
+#ifdef CONFIG_NOR
+ writel(0x00000200, &gpmc_cfg->config);
+#else
+ writel(0x00000012, &gpmc_cfg->config);
+#endif
/*
* Disable the GPMC0 config set by ROM code
- * It conflicts with our MPDB (both at 0x08000000)
*/
writel(0, &gpmc_cfg->cs[0].config7);
+ sdelay(1000);
+ /* enable chip-select specific configurations */
+ enable_gpmc_cs_config(gpmc_regs, &gpmc_cfg->cs[0], base, size);
}
diff --git a/arch/arm/cpu/armv7/omap3/Makefile b/arch/arm/cpu/armv7/omap3/Makefile
index 39ff257..cf86046 100644
--- a/arch/arm/cpu/armv7/omap3/Makefile
+++ b/arch/arm/cpu/armv7/omap3/Makefile
@@ -9,7 +9,6 @@ obj-y := lowlevel_init.o
obj-y += board.o
obj-y += clock.o
-obj-y += mem.o
obj-y += sys_info.o
ifdef CONFIG_SPL_BUILD
obj-$(CONFIG_SPL_OMAP3_ID_NAND) += spl_id_nand.o
diff --git a/arch/arm/cpu/armv7/omap5/hw_data.c b/arch/arm/cpu/armv7/omap5/hw_data.c
index ad97132..4baca11 100644
--- a/arch/arm/cpu/armv7/omap5/hw_data.c
+++ b/arch/arm/cpu/armv7/omap5/hw_data.c
@@ -372,6 +372,38 @@ struct vcores_data dra752_volts = {
.iva.pmic = &tps659038,
};
+struct vcores_data dra722_volts = {
+ .mpu.value = 1000,
+ .mpu.efuse.reg = STD_FUSE_OPP_VMIN_MPU_NOM,
+ .mpu.efuse.reg_bits = DRA752_EFUSE_REGBITS,
+ .mpu.addr = 0x23,
+ .mpu.pmic = &tps659038,
+
+ .eve.value = 1000,
+ .eve.efuse.reg = STD_FUSE_OPP_VMIN_DSPEVE_NOM,
+ .eve.efuse.reg_bits = DRA752_EFUSE_REGBITS,
+ .eve.addr = 0x2f,
+ .eve.pmic = &tps659038,
+
+ .gpu.value = 1000,
+ .gpu.efuse.reg = STD_FUSE_OPP_VMIN_GPU_NOM,
+ .gpu.efuse.reg_bits = DRA752_EFUSE_REGBITS,
+ .gpu.addr = 0x2f,
+ .gpu.pmic = &tps659038,
+
+ .core.value = 1000,
+ .core.efuse.reg = STD_FUSE_OPP_VMIN_CORE_NOM,
+ .core.efuse.reg_bits = DRA752_EFUSE_REGBITS,
+ .core.addr = 0x27,
+ .core.pmic = &tps659038,
+
+ .iva.value = 1000,
+ .iva.efuse.reg = STD_FUSE_OPP_VMIN_IVA_NOM,
+ .iva.efuse.reg_bits = DRA752_EFUSE_REGBITS,
+ .iva.addr = 0x2f,
+ .iva.pmic = &tps659038,
+};
+
/*
* Enable essential clock domains, modules and
* do some additional special settings needed
@@ -558,6 +590,13 @@ void hw_data_init(void)
*ctrl = &dra7xx_ctrl;
break;
+ case DRA722_ES1_0:
+ *prcm = &dra7xx_prcm;
+ *dplls_data = &dra7xx_dplls;
+ *omap_vcores = &dra722_volts;
+ *ctrl = &dra7xx_ctrl;
+ break;
+
default:
printf("\n INVALID OMAP REVISION ");
}
@@ -580,6 +619,7 @@ void get_ioregs(const struct ctrl_ioregs **regs)
break;
case DRA752_ES1_0:
case DRA752_ES1_1:
+ case DRA722_ES1_0:
*regs = &ioregs_dra7xx_es1;
break;
diff --git a/arch/arm/cpu/armv7/omap5/hwinit.c b/arch/arm/cpu/armv7/omap5/hwinit.c
index 93feb16..a8a474a 100644
--- a/arch/arm/cpu/armv7/omap5/hwinit.c
+++ b/arch/arm/cpu/armv7/omap5/hwinit.c
@@ -336,6 +336,9 @@ void init_omap_revision(void)
case DRA752_CONTROL_ID_CODE_ES1_1:
*omap_si_rev = DRA752_ES1_1;
break;
+ case DRA722_CONTROL_ID_CODE_ES1_0:
+ *omap_si_rev = DRA722_ES1_0;
+ break;
default:
*omap_si_rev = OMAP5430_SILICON_ID_INVALID;
}
diff --git a/arch/arm/cpu/armv7/omap5/prcm-regs.c b/arch/arm/cpu/armv7/omap5/prcm-regs.c
index 7292161..ff08ef4 100644
--- a/arch/arm/cpu/armv7/omap5/prcm-regs.c
+++ b/arch/arm/cpu/armv7/omap5/prcm-regs.c
@@ -447,10 +447,10 @@ struct omap_sys_ctrl_regs const dra7xx_ctrl = {
.control_wkup_control_spare_r = 0x4AE0C5B4,
.control_wkup_control_spare_r_c0 = 0x4AE0C5B8,
.control_srcomp_east_side_wkup = 0x4AE0C5BC,
- .control_efuse_1 = 0x4AE0C5C0,
- .control_efuse_2 = 0x4AE0C5C4,
- .control_efuse_3 = 0x4AE0C5C8,
- .control_efuse_4 = 0x4AE0C5CC,
+ .control_efuse_1 = 0x4AE0C5C8,
+ .control_efuse_2 = 0x4AE0C5CC,
+ .control_efuse_3 = 0x4AE0C5D0,
+ .control_efuse_4 = 0x4AE0C5D4,
.control_efuse_13 = 0x4AE0C5F0,
};
diff --git a/arch/arm/cpu/armv7/omap5/sdram.c b/arch/arm/cpu/armv7/omap5/sdram.c
index 16a91f9..e2ebab8 100644
--- a/arch/arm/cpu/armv7/omap5/sdram.c
+++ b/arch/arm/cpu/armv7/omap5/sdram.c
@@ -229,6 +229,17 @@ const struct dmm_lisa_map_regs lisa_map_2G_x_2_x_2 = {
.is_ma_present = 0x1
};
+/*
+ * DRA722 EVM EMIF1 CONFIGURATION
+ */
+const struct dmm_lisa_map_regs lisa_map_2G_x_2 = {
+ .dmm_lisa_map_0 = 0x0,
+ .dmm_lisa_map_1 = 0x0,
+ .dmm_lisa_map_2 = 0x80600100,
+ .dmm_lisa_map_3 = 0xFF020100,
+ .is_ma_present = 0x1
+};
+
static void emif_get_reg_dump_sdp(u32 emif_nr, const struct emif_regs **regs)
{
switch (omap_revision()) {
@@ -255,6 +266,7 @@ static void emif_get_reg_dump_sdp(u32 emif_nr, const struct emif_regs **regs)
break;
}
break;
+ case DRA722_ES1_0:
default:
*regs = &emif_1_regs_ddr3_532_mhz_1cs_dra_es1;
}
@@ -275,8 +287,11 @@ static void emif_get_dmm_regs_sdp(const struct dmm_lisa_map_regs
break;
case DRA752_ES1_0:
case DRA752_ES1_1:
- default:
*dmm_lisa_regs = &lisa_map_2G_x_2_x_2_2G_x_1_x_2;
+ break;
+ case DRA722_ES1_0:
+ default:
+ *dmm_lisa_regs = &lisa_map_2G_x_2;
}
}
@@ -463,6 +478,7 @@ static void emif_get_ext_phy_ctrl_const_regs(u32 emif_nr,
break;
case DRA752_ES1_0:
case DRA752_ES1_1:
+ case DRA722_ES1_0:
if (emif_nr == 1) {
*regs = dra_ddr3_ext_phy_ctrl_const_base_es1_emif1;
*size =
@@ -630,6 +646,7 @@ const struct read_write_regs *get_bug_regs(u32 *iterations)
break;
case DRA752_ES1_0:
case DRA752_ES1_1:
+ case DRA722_ES1_0:
bug_00339_regs_ptr = dra_bug_00339_regs;
*iterations = sizeof(dra_bug_00339_regs)/
sizeof(dra_bug_00339_regs[0]);
diff --git a/arch/arm/cpu/armv7/rmobile/pfc-r8a7791.c b/arch/arm/cpu/armv7/rmobile/pfc-r8a7791.c
index f49f990..46d6e60 100644
--- a/arch/arm/cpu/armv7/rmobile/pfc-r8a7791.c
+++ b/arch/arm/cpu/armv7/rmobile/pfc-r8a7791.c
@@ -913,7 +913,7 @@ static struct pinmux_cfg_reg pinmux_config_regs[] = {
/* SEL_SCIF3 [2] */
FN_SEL_SCIF3_0, FN_SEL_SCIF3_1, FN_SEL_SCIF3_2, FN_SEL_SCIF3_3,
/* SEL_IEB [2] */
- FN_SEL_IEB_0, FN_SEL_IEB_1, FN_SEL_IEB_2,
+ FN_SEL_IEB_0, FN_SEL_IEB_1, FN_SEL_IEB_2, 0,
/* SEL_MMC [1] */
FN_SEL_MMC_0, FN_SEL_MMC_1,
/* SEL_SCIF5 [1] */
diff --git a/arch/arm/cpu/armv7/zynq/cpu.c b/arch/arm/cpu/armv7/zynq/cpu.c
index 7626b5c..816d0c5 100644
--- a/arch/arm/cpu/armv7/zynq/cpu.c
+++ b/arch/arm/cpu/armv7/zynq/cpu.c
@@ -14,6 +14,9 @@ void lowlevel_init(void)
{
}
+#define ZYNQ_SILICON_VER_MASK 0xF0000000
+#define ZYNQ_SILICON_VER_SHIFT 28
+
int arch_cpu_init(void)
{
zynq_slcr_unlock();
@@ -42,6 +45,16 @@ int arch_cpu_init(void)
return 0;
}
+unsigned int zynq_get_silicon_version(void)
+{
+ unsigned int ver;
+
+ ver = (readl(&devcfg_base->mctrl) &
+ ZYNQ_SILICON_VER_MASK) >> ZYNQ_SILICON_VER_SHIFT;
+
+ return ver;
+}
+
void reset_cpu(ulong addr)
{
zynq_slcr_cpu_reset();
diff --git a/arch/arm/cpu/armv7/zynq/ddrc.c b/arch/arm/cpu/armv7/zynq/ddrc.c
index ba6a6ae..e0ed3bf 100644
--- a/arch/arm/cpu/armv7/zynq/ddrc.c
+++ b/arch/arm/cpu/armv7/zynq/ddrc.c
@@ -40,11 +40,8 @@ void zynq_ddrc_init(void)
* first stage bootloader. To get ECC to work all memory has
* been initialized by writing any value.
*/
- memset(0, 0, 1 * 1024 * 1024);
+ memset((void *)0, 0, 1 * 1024 * 1024);
} else {
puts("Memory: ECC disabled\n");
}
-
- if (width == ZYNQ_DDRC_CTRLREG_BUSWIDTH_16BIT)
- gd->ram_size /= 2;
}
diff --git a/arch/arm/cpu/armv7/zynq/slcr.c b/arch/arm/cpu/armv7/zynq/slcr.c
index d7c1882..934ccc3 100644
--- a/arch/arm/cpu/armv7/zynq/slcr.c
+++ b/arch/arm/cpu/armv7/zynq/slcr.c
@@ -8,26 +8,75 @@
#include <asm/io.h>
#include <malloc.h>
#include <asm/arch/hardware.h>
+#include <asm/arch/sys_proto.h>
#include <asm/arch/clk.h>
#define SLCR_LOCK_MAGIC 0x767B
#define SLCR_UNLOCK_MAGIC 0xDF0D
+#define SLCR_USB_L1_SEL 0x04
+
#define SLCR_IDCODE_MASK 0x1F000
#define SLCR_IDCODE_SHIFT 12
+/*
+ * zynq_slcr_mio_get_status - Get the status of MIO peripheral.
+ *
+ * @peri_name: Name of the peripheral for checking MIO status
+ * @get_pins: Pointer to array of get pin for this peripheral
+ * @num_pins: Number of pins for this peripheral
+ * @mask: Mask value
+ * @check_val: Required check value to get the status of periph
+ */
+struct zynq_slcr_mio_get_status {
+ const char *peri_name;
+ const int *get_pins;
+ int num_pins;
+ u32 mask;
+ u32 check_val;
+};
+
+static const int usb0_pins[] = {
+ 28, 29, 30, 31, 32, 33, 34, 35, 36, 37, 38, 39
+};
+
+static const int usb1_pins[] = {
+ 40, 41, 42, 43, 44, 45, 46, 47, 48, 49, 50, 51
+};
+
+static const struct zynq_slcr_mio_get_status mio_periphs[] = {
+ {
+ "usb0",
+ usb0_pins,
+ ARRAY_SIZE(usb0_pins),
+ SLCR_USB_L1_SEL,
+ SLCR_USB_L1_SEL,
+ },
+ {
+ "usb1",
+ usb1_pins,
+ ARRAY_SIZE(usb1_pins),
+ SLCR_USB_L1_SEL,
+ SLCR_USB_L1_SEL,
+ },
+};
+
static int slcr_lock = 1; /* 1 means locked, 0 means unlocked */
void zynq_slcr_lock(void)
{
- if (!slcr_lock)
+ if (!slcr_lock) {
writel(SLCR_LOCK_MAGIC, &slcr_base->slcr_lock);
+ slcr_lock = 1;
+ }
}
void zynq_slcr_unlock(void)
{
- if (slcr_lock)
+ if (slcr_lock) {
writel(SLCR_UNLOCK_MAGIC, &slcr_base->slcr_unlock);
+ slcr_lock = 0;
+ }
}
/* Reset the entire system */
@@ -82,7 +131,7 @@ void zynq_slcr_devcfg_disable(void)
{
zynq_slcr_unlock();
- /* Disable AXI interface */
+ /* Disable AXI interface by asserting FPGA resets */
writel(0xFFFFFFFF, &slcr_base->fpga_rst_ctrl);
/* Set Level Shifters DT618760 */
@@ -98,7 +147,7 @@ void zynq_slcr_devcfg_enable(void)
/* Set Level Shifters DT618760 */
writel(0xF, &slcr_base->lvl_shftr_en);
- /* Disable AXI interface */
+ /* Enable AXI interface by de-asserting FPGA resets */
writel(0x0, &slcr_base->fpga_rst_ctrl);
zynq_slcr_lock();
@@ -115,3 +164,33 @@ u32 zynq_slcr_get_idcode(void)
return (readl(&slcr_base->pss_idcode) & SLCR_IDCODE_MASK) >>
SLCR_IDCODE_SHIFT;
}
+
+/*
+ * zynq_slcr_get_mio_pin_status - Get the MIO pin status of peripheral.
+ *
+ * @periph: Name of the peripheral
+ *
+ * Returns count to indicate the number of pins configured for the
+ * given @periph.
+ */
+int zynq_slcr_get_mio_pin_status(const char *periph)
+{
+ const struct zynq_slcr_mio_get_status *mio_ptr;
+ int val, i, j;
+ int mio = 0;
+
+ for (i = 0; i < ARRAY_SIZE(mio_periphs); i++) {
+ if (strcmp(periph, mio_periphs[i].peri_name) == 0) {
+ mio_ptr = &mio_periphs[i];
+ for (j = 0; j < mio_ptr->num_pins; j++) {
+ val = readl(&slcr_base->mio_pin
+ [mio_ptr->get_pins[j]]);
+ if ((val & mio_ptr->mask) == mio_ptr->check_val)
+ mio++;
+ }
+ break;
+ }
+ }
+
+ return mio;
+}
diff --git a/arch/arm/cpu/armv7/zynq/spl.c b/arch/arm/cpu/armv7/zynq/spl.c
index fcad762..d73e5cb 100644
--- a/arch/arm/cpu/armv7/zynq/spl.c
+++ b/arch/arm/cpu/armv7/zynq/spl.c
@@ -28,6 +28,13 @@ void board_init_f(ulong dummy)
board_init_r(NULL, 0);
}
+#ifdef CONFIG_SPL_BOARD_INIT
+void spl_board_init(void)
+{
+ board_init();
+}
+#endif
+
u32 spl_boot_device(void)
{
u32 mode;
@@ -67,3 +74,11 @@ int spl_start_uboot(void)
return 0;
}
#endif
+
+__weak void ps7_init(void)
+{
+ /*
+ * This function is overridden by the one in
+ * board/xilinx/zynq/ps7_init.c, if it exists.
+ */
+}
diff --git a/arch/arm/dts/zynq-7000.dtsi b/arch/arm/dts/zynq-7000.dtsi
index f20b8bd..2d076f1 100644
--- a/arch/arm/dts/zynq-7000.dtsi
+++ b/arch/arm/dts/zynq-7000.dtsi
@@ -10,4 +10,198 @@
/ {
compatible = "xlnx,zynq-7000";
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu@0 {
+ compatible = "arm,cortex-a9";
+ device_type = "cpu";
+ reg = <0>;
+ clocks = <&clkc 3>;
+ clock-latency = <1000>;
+ operating-points = <
+ /* kHz uV */
+ 666667 1000000
+ 333334 1000000
+ 222223 1000000
+ >;
+ };
+
+ cpu@1 {
+ compatible = "arm,cortex-a9";
+ device_type = "cpu";
+ reg = <1>;
+ clocks = <&clkc 3>;
+ };
+ };
+
+ pmu {
+ compatible = "arm,cortex-a9-pmu";
+ interrupts = <0 5 4>, <0 6 4>;
+ interrupt-parent = <&intc>;
+ reg = < 0xf8891000 0x1000 0xf8893000 0x1000 >;
+ };
+
+ amba {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ interrupt-parent = <&intc>;
+ ranges;
+
+ i2c0: zynq-i2c@e0004000 {
+ compatible = "cdns,i2c-r1p10";
+ status = "disabled";
+ clocks = <&clkc 38>;
+ interrupt-parent = <&intc>;
+ interrupts = <0 25 4>;
+ reg = <0xe0004000 0x1000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ i2c1: zynq-i2c@e0005000 {
+ compatible = "cdns,i2c-r1p10";
+ status = "disabled";
+ clocks = <&clkc 39>;
+ interrupt-parent = <&intc>;
+ interrupts = <0 48 4>;
+ reg = <0xe0005000 0x1000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ intc: interrupt-controller@f8f01000 {
+ compatible = "arm,cortex-a9-gic";
+ #interrupt-cells = <3>;
+ #address-cells = <1>;
+ interrupt-controller;
+ reg = <0xF8F01000 0x1000>,
+ <0xF8F00100 0x100>;
+ };
+
+ L2: cache-controller {
+ compatible = "arm,pl310-cache";
+ reg = <0xF8F02000 0x1000>;
+ arm,data-latency = <3 2 2>;
+ arm,tag-latency = <2 2 2>;
+ cache-unified;
+ cache-level = <2>;
+ };
+
+ uart0: uart@e0000000 {
+ compatible = "xlnx,xuartps";
+ status = "disabled";
+ clocks = <&clkc 23>, <&clkc 40>;
+ clock-names = "ref_clk", "aper_clk";
+ reg = <0xE0000000 0x1000>;
+ interrupts = <0 27 4>;
+ };
+
+ uart1: uart@e0001000 {
+ compatible = "xlnx,xuartps";
+ status = "disabled";
+ clocks = <&clkc 24>, <&clkc 41>;
+ clock-names = "ref_clk", "aper_clk";
+ reg = <0xE0001000 0x1000>;
+ interrupts = <0 50 4>;
+ };
+
+ gem0: ethernet@e000b000 {
+ compatible = "cdns,gem";
+ reg = <0xe000b000 0x4000>;
+ status = "disabled";
+ interrupts = <0 22 4>;
+ clocks = <&clkc 30>, <&clkc 30>, <&clkc 13>;
+ clock-names = "pclk", "hclk", "tx_clk";
+ };
+
+ gem1: ethernet@e000c000 {
+ compatible = "cdns,gem";
+ reg = <0xe000c000 0x4000>;
+ status = "disabled";
+ interrupts = <0 45 4>;
+ clocks = <&clkc 31>, <&clkc 31>, <&clkc 14>;
+ clock-names = "pclk", "hclk", "tx_clk";
+ };
+
+ sdhci0: ps7-sdhci@e0100000 {
+ compatible = "arasan,sdhci-8.9a";
+ status = "disabled";
+ clock-names = "clk_xin", "clk_ahb";
+ clocks = <&clkc 21>, <&clkc 32>;
+ interrupt-parent = <&intc>;
+ interrupts = <0 24 4>;
+ reg = <0xe0100000 0x1000>;
+ } ;
+
+ sdhci1: ps7-sdhci@e0101000 {
+ compatible = "arasan,sdhci-8.9a";
+ status = "disabled";
+ clock-names = "clk_xin", "clk_ahb";
+ clocks = <&clkc 22>, <&clkc 33>;
+ interrupt-parent = <&intc>;
+ interrupts = <0 47 4>;
+ reg = <0xe0101000 0x1000>;
+ } ;
+
+ slcr: slcr@f8000000 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "xlnx,zynq-slcr", "syscon";
+ reg = <0xF8000000 0x1000>;
+ ranges;
+ clkc: clkc@100 {
+ #clock-cells = <1>;
+ compatible = "xlnx,ps7-clkc";
+ ps-clk-frequency = <33333333>;
+ fclk-enable = <0>;
+ clock-output-names = "armpll", "ddrpll", "iopll", "cpu_6or4x",
+ "cpu_3or2x", "cpu_2x", "cpu_1x", "ddr2x", "ddr3x",
+ "dci", "lqspi", "smc", "pcap", "gem0", "gem1",
+ "fclk0", "fclk1", "fclk2", "fclk3", "can0", "can1",
+ "sdio0", "sdio1", "uart0", "uart1", "spi0", "spi1",
+ "dma", "usb0_aper", "usb1_aper", "gem0_aper",
+ "gem1_aper", "sdio0_aper", "sdio1_aper",
+ "spi0_aper", "spi1_aper", "can0_aper", "can1_aper",
+ "i2c0_aper", "i2c1_aper", "uart0_aper", "uart1_aper",
+ "gpio_aper", "lqspi_aper", "smc_aper", "swdt",
+ "dbg_trc", "dbg_apb";
+ reg = <0x100 0x100>;
+ };
+ };
+
+ global_timer: timer@f8f00200 {
+ compatible = "arm,cortex-a9-global-timer";
+ reg = <0xf8f00200 0x20>;
+ interrupts = <1 11 0x301>;
+ interrupt-parent = <&intc>;
+ clocks = <&clkc 4>;
+ };
+
+ ttc0: ttc0@f8001000 {
+ interrupt-parent = <&intc>;
+ interrupts = < 0 10 4 0 11 4 0 12 4 >;
+ compatible = "cdns,ttc";
+ clocks = <&clkc 6>;
+ reg = <0xF8001000 0x1000>;
+ };
+
+ ttc1: ttc1@f8002000 {
+ interrupt-parent = <&intc>;
+ interrupts = < 0 37 4 0 38 4 0 39 4 >;
+ compatible = "cdns,ttc";
+ clocks = <&clkc 6>;
+ reg = <0xF8002000 0x1000>;
+ };
+ scutimer: scutimer@f8f00600 {
+ interrupt-parent = <&intc>;
+ interrupts = < 1 13 0x301 >;
+ compatible = "arm,cortex-a9-twd-timer";
+ reg = < 0xf8f00600 0x20 >;
+ clocks = <&clkc 4>;
+ } ;
+ };
};
diff --git a/arch/arm/dts/zynq-microzed.dts b/arch/arm/dts/zynq-microzed.dts
index 6da71c1..c373a2c 100644
--- a/arch/arm/dts/zynq-microzed.dts
+++ b/arch/arm/dts/zynq-microzed.dts
@@ -11,4 +11,13 @@
/ {
model = "Zynq MicroZED Board";
compatible = "xlnx,zynq-microzed", "xlnx,zynq-7000";
+
+ aliases {
+ serial0 = &uart1;
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0 0x40000000>;
+ };
};
diff --git a/arch/arm/dts/zynq-zc702.dts b/arch/arm/dts/zynq-zc702.dts
index 667dc28..4fa0b00 100644
--- a/arch/arm/dts/zynq-zc702.dts
+++ b/arch/arm/dts/zynq-zc702.dts
@@ -11,4 +11,13 @@
/ {
model = "Zynq ZC702 Board";
compatible = "xlnx,zynq-zc702", "xlnx,zynq-7000";
+
+ aliases {
+ serial0 = &uart1;
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0 0x40000000>;
+ };
};
diff --git a/arch/arm/dts/zynq-zc706.dts b/arch/arm/dts/zynq-zc706.dts
index 526fc88..2a80195 100644
--- a/arch/arm/dts/zynq-zc706.dts
+++ b/arch/arm/dts/zynq-zc706.dts
@@ -11,4 +11,13 @@
/ {
model = "Zynq ZC706 Board";
compatible = "xlnx,zynq-zc706", "xlnx,zynq-7000";
+
+ aliases {
+ serial0 = &uart1;
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0 0x40000000>;
+ };
};
diff --git a/arch/arm/dts/zynq-zc770-xm010.dts b/arch/arm/dts/zynq-zc770-xm010.dts
index 8b542a1..5e661749 100644
--- a/arch/arm/dts/zynq-zc770-xm010.dts
+++ b/arch/arm/dts/zynq-zc770-xm010.dts
@@ -11,4 +11,13 @@
/ {
model = "Zynq ZC770 XM010 Board";
compatible = "xlnx,zynq-zc770-xm010", "xlnx,zynq-7000";
+
+ aliases {
+ serial0 = &uart1;
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0 0x40000000>;
+ };
};
diff --git a/arch/arm/dts/zynq-zc770-xm012.dts b/arch/arm/dts/zynq-zc770-xm012.dts
index 0379a07..127a661 100644
--- a/arch/arm/dts/zynq-zc770-xm012.dts
+++ b/arch/arm/dts/zynq-zc770-xm012.dts
@@ -11,4 +11,13 @@
/ {
model = "Zynq ZC770 XM012 Board";
compatible = "xlnx,zynq-zc770-xm012", "xlnx,zynq-7000";
+
+ aliases {
+ serial0 = &uart1;
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0 0x40000000>;
+ };
};
diff --git a/arch/arm/dts/zynq-zc770-xm013.dts b/arch/arm/dts/zynq-zc770-xm013.dts
index a4f9e05..c61c7e7 100644
--- a/arch/arm/dts/zynq-zc770-xm013.dts
+++ b/arch/arm/dts/zynq-zc770-xm013.dts
@@ -11,4 +11,13 @@
/ {
model = "Zynq ZC770 XM013 Board";
compatible = "xlnx,zynq-zc770-xm013", "xlnx,zynq-7000";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0 0x40000000>;
+ };
};
diff --git a/arch/arm/dts/zynq-zed.dts b/arch/arm/dts/zynq-zed.dts
index 91a5deb..70cc8a6 100644
--- a/arch/arm/dts/zynq-zed.dts
+++ b/arch/arm/dts/zynq-zed.dts
@@ -11,4 +11,13 @@
/ {
model = "Zynq ZED Board";
compatible = "xlnx,zynq-zed", "xlnx,zynq-7000";
+
+ aliases {
+ serial0 = &uart1;
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0 0x20000000>;
+ };
};
diff --git a/arch/arm/include/asm/arch-am33xx/sys_proto.h b/arch/arm/include/asm/arch-am33xx/sys_proto.h
index 91ff2ad..33a82fc 100644
--- a/arch/arm/include/asm/arch-am33xx/sys_proto.h
+++ b/arch/arm/include/asm/arch-am33xx/sys_proto.h
@@ -11,6 +11,7 @@
#ifndef _SYS_PROTO_H_
#define _SYS_PROTO_H_
#include <linux/mtd/omap_gpmc.h>
+#include <asm/ti-common/sys_proto.h>
#include <asm/arch/cpu.h>
#define BOARD_REV_ID 0x0
diff --git a/arch/arm/include/asm/arch-omap3/mem.h b/arch/arm/include/asm/arch-omap3/mem.h
index 1804191..bdb1435 100644
--- a/arch/arm/include/asm/arch-omap3/mem.h
+++ b/arch/arm/include/asm/arch-omap3/mem.h
@@ -344,6 +344,7 @@ enum {
* MAP - Map this CS to which address(GPMC address space)- Absolute address
* >>24 before being used.
*/
+#define GPMC_SIZE_256M 0x0
#define GPMC_SIZE_128M 0x8
#define GPMC_SIZE_64M 0xC
#define GPMC_SIZE_32M 0xE
diff --git a/arch/arm/include/asm/arch-omap4/cpu.h b/arch/arm/include/asm/arch-omap4/cpu.h
index c21fb54..f7595ae 100644
--- a/arch/arm/include/asm/arch-omap4/cpu.h
+++ b/arch/arm/include/asm/arch-omap4/cpu.h
@@ -12,6 +12,8 @@
#include <asm/types.h>
#endif /* !(__KERNEL_STRICT_NAMES || __ASSEMBLY__) */
+#include <asm/arch/hardware.h>
+
#ifndef __KERNEL_STRICT_NAMES
#ifndef __ASSEMBLY__
struct gptimer {
@@ -57,9 +59,6 @@ struct watchdog {
#define TCLR_AR (0x1 << 1)
#define TCLR_PRE (0x1 << 5)
-/* GPMC BASE */
-#define GPMC_BASE (OMAP44XX_GPMC_BASE)
-
/* I2C base */
#define I2C_BASE1 (OMAP44XX_L4_PER_BASE + 0x70000)
#define I2C_BASE2 (OMAP44XX_L4_PER_BASE + 0x72000)
diff --git a/arch/arm/include/asm/arch-omap4/hardware.h b/arch/arm/include/asm/arch-omap4/hardware.h
new file mode 100644
index 0000000..f7011b4
--- /dev/null
+++ b/arch/arm/include/asm/arch-omap4/hardware.h
@@ -0,0 +1,26 @@
+/*
+ * hardware.h
+ *
+ * hardware specific header
+ *
+ * Copyright (C) 2013, Texas Instruments, Incorporated - http://www.ti.com/
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __OMAP_HARDWARE_H
+#define __OMAP_HARDWARE_H
+
+#include <asm/arch/omap.h>
+
+/*
+ * Common hardware definitions
+ */
+
+/* BCH Error Location Module */
+#define ELM_BASE 0x48078000
+
+/* GPMC Base address */
+#define GPMC_BASE 0x50000000
+
+#endif
diff --git a/arch/arm/include/asm/arch-omap4/mem.h b/arch/arm/include/asm/arch-omap4/mem.h
new file mode 100644
index 0000000..d2e708b
--- /dev/null
+++ b/arch/arm/include/asm/arch-omap4/mem.h
@@ -0,0 +1,62 @@
+/*
+ * (C) Copyright 2006-2008
+ * Texas Instruments, <www.ti.com>
+ *
+ * Author
+ * Mansoor Ahamed <mansoor.ahamed@ti.com>
+ *
+ * Initial Code from:
+ * Richard Woodruff <r-woodruff2@ti.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef _MEM_H_
+#define _MEM_H_
+
+/*
+ * GPMC settings -
+ * Definitions is as per the following format
+ * #define <PART>_GPMC_CONFIG<x> <value>
+ * Where:
+ * PART is the part name e.g. STNOR - Intel Strata Flash
+ * x is GPMC config registers from 1 to 6 (there will be 6 macros)
+ * Value is corresponding value
+ *
+ * For every valid PRCM configuration there should be only one definition of
+ * the same. if values are independent of the board, this definition will be
+ * present in this file if values are dependent on the board, then this should
+ * go into corresponding mem-boardName.h file
+ *
+ * Currently valid part Names are (PART):
+ * M_NAND - Micron NAND
+ * STNOR - STMicrolelctronics M29W128GL
+ */
+#define GPMC_SIZE_256M 0x0
+#define GPMC_SIZE_128M 0x8
+#define GPMC_SIZE_64M 0xC
+#define GPMC_SIZE_32M 0xE
+#define GPMC_SIZE_16M 0xF
+
+#define M_NAND_GPMC_CONFIG1 0x00000800
+#define M_NAND_GPMC_CONFIG2 0x001e1e00
+#define M_NAND_GPMC_CONFIG3 0x001e1e00
+#define M_NAND_GPMC_CONFIG4 0x16051807
+#define M_NAND_GPMC_CONFIG5 0x00151e1e
+#define M_NAND_GPMC_CONFIG6 0x16000f80
+#define M_NAND_GPMC_CONFIG7 0x00000008
+
+#define STNOR_GPMC_CONFIG1 0x00001200
+#define STNOR_GPMC_CONFIG2 0x00101000
+#define STNOR_GPMC_CONFIG3 0x00030301
+#define STNOR_GPMC_CONFIG4 0x10041004
+#define STNOR_GPMC_CONFIG5 0x000C1010
+#define STNOR_GPMC_CONFIG6 0x08070280
+#define STNOR_GPMC_CONFIG7 0x00000F48
+
+/* max number of GPMC Chip Selects */
+#define GPMC_MAX_CS 8
+/* max number of GPMC regs */
+#define GPMC_MAX_REG 7
+
+#endif /* endif _MEM_H_ */
diff --git a/arch/arm/include/asm/arch-omap4/omap.h b/arch/arm/include/asm/arch-omap4/omap.h
index f66da0d..d43dc26 100644
--- a/arch/arm/include/asm/arch-omap4/omap.h
+++ b/arch/arm/include/asm/arch-omap4/omap.h
@@ -60,9 +60,6 @@
/* Watchdog Timer2 - MPU watchdog */
#define WDT2_BASE (OMAP44XX_L4_WKUP_BASE + 0x14000)
-/* GPMC */
-#define OMAP44XX_GPMC_BASE 0x50000000
-
/*
* Hardware Register Details
*/
diff --git a/arch/arm/include/asm/arch-omap4/sys_proto.h b/arch/arm/include/asm/arch-omap4/sys_proto.h
index 80172f3..83d858f 100644
--- a/arch/arm/include/asm/arch-omap4/sys_proto.h
+++ b/arch/arm/include/asm/arch-omap4/sys_proto.h
@@ -14,6 +14,7 @@
#include <asm/omap_common.h>
#include <linux/mtd/omap_gpmc.h>
#include <asm/arch/mux_omap4.h>
+#include <asm/ti-common/sys_proto.h>
DECLARE_GLOBAL_DATA_PTR;
@@ -53,54 +54,4 @@ int omap_vc_bypass_send_value(u8 sa, u8 reg_addr, u8 reg_data);
u32 warm_reset(void);
void force_emif_self_refresh(void);
void setup_warmreset_time(void);
-
-static inline u32 running_from_sdram(void)
-{
- u32 pc;
- asm volatile ("mov %0, pc" : "=r" (pc));
- return ((pc >= OMAP44XX_DRAM_ADDR_SPACE_START) &&
- (pc < OMAP44XX_DRAM_ADDR_SPACE_END));
-}
-
-static inline u8 uboot_loaded_by_spl(void)
-{
- /*
- * u-boot can be running from sdram either because of configuration
- * Header or by SPL. If because of CH, then the romcode sets the
- * CHSETTINGS executed bit to true in the boot parameter structure that
- * it passes to the bootloader.This parameter is stored in the ch_flags
- * variable by both SPL and u-boot.Check out for CHSETTINGS, which is a
- * mandatory section if CH is present.
- */
- if ((gd->arch.omap_boot_params.ch_flags) & (CH_FLAGS_CHSETTINGS))
- return 0;
- else
- return running_from_sdram();
-}
-/*
- * The basic hardware init of OMAP(s_init()) can happen in 4
- * different contexts:
- * 1. SPL running from SRAM
- * 2. U-Boot running from FLASH
- * 3. Non-XIP U-Boot loaded to SDRAM by SPL
- * 4. Non-XIP U-Boot loaded to SDRAM by ROM code using the
- * Configuration Header feature
- *
- * This function finds this context.
- * Defining as inline may help in compiling out unused functions in SPL
- */
-static inline u32 omap_hw_init_context(void)
-{
-#ifdef CONFIG_SPL_BUILD
- return OMAP_INIT_CONTEXT_SPL;
-#else
- if (uboot_loaded_by_spl())
- return OMAP_INIT_CONTEXT_UBOOT_AFTER_SPL;
- else if (running_from_sdram())
- return OMAP_INIT_CONTEXT_UBOOT_AFTER_CH;
- else
- return OMAP_INIT_CONTEXT_UBOOT_FROM_NOR;
-#endif
-}
-
#endif
diff --git a/arch/arm/include/asm/arch-omap5/cpu.h b/arch/arm/include/asm/arch-omap5/cpu.h
index 5f1d745..6109b92 100644
--- a/arch/arm/include/asm/arch-omap5/cpu.h
+++ b/arch/arm/include/asm/arch-omap5/cpu.h
@@ -14,6 +14,8 @@
#include <asm/types.h>
#endif /* !(__KERNEL_STRICT_NAMES || __ASSEMBLY__) */
+#include <asm/arch/hardware.h>
+
#ifndef __KERNEL_STRICT_NAMES
#ifndef __ASSEMBLY__
struct gptimer {
@@ -63,9 +65,6 @@ struct watchdog {
#define TCLR_AR (0x1 << 1)
#define TCLR_PRE (0x1 << 5)
-/* GPMC BASE */
-#define GPMC_BASE (OMAP54XX_GPMC_BASE)
-
/* I2C base */
#define I2C_BASE1 (OMAP54XX_L4_PER_BASE + 0x70000)
#define I2C_BASE2 (OMAP54XX_L4_PER_BASE + 0x72000)
diff --git a/arch/arm/include/asm/arch-omap5/hardware.h b/arch/arm/include/asm/arch-omap5/hardware.h
new file mode 100644
index 0000000..f7011b4
--- /dev/null
+++ b/arch/arm/include/asm/arch-omap5/hardware.h
@@ -0,0 +1,26 @@
+/*
+ * hardware.h
+ *
+ * hardware specific header
+ *
+ * Copyright (C) 2013, Texas Instruments, Incorporated - http://www.ti.com/
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __OMAP_HARDWARE_H
+#define __OMAP_HARDWARE_H
+
+#include <asm/arch/omap.h>
+
+/*
+ * Common hardware definitions
+ */
+
+/* BCH Error Location Module */
+#define ELM_BASE 0x48078000
+
+/* GPMC Base address */
+#define GPMC_BASE 0x50000000
+
+#endif
diff --git a/arch/arm/include/asm/arch-omap5/mem.h b/arch/arm/include/asm/arch-omap5/mem.h
new file mode 100644
index 0000000..d2e708b
--- /dev/null
+++ b/arch/arm/include/asm/arch-omap5/mem.h
@@ -0,0 +1,62 @@
+/*
+ * (C) Copyright 2006-2008
+ * Texas Instruments, <www.ti.com>
+ *
+ * Author
+ * Mansoor Ahamed <mansoor.ahamed@ti.com>
+ *
+ * Initial Code from:
+ * Richard Woodruff <r-woodruff2@ti.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef _MEM_H_
+#define _MEM_H_
+
+/*
+ * GPMC settings -
+ * Definitions is as per the following format
+ * #define <PART>_GPMC_CONFIG<x> <value>
+ * Where:
+ * PART is the part name e.g. STNOR - Intel Strata Flash
+ * x is GPMC config registers from 1 to 6 (there will be 6 macros)
+ * Value is corresponding value
+ *
+ * For every valid PRCM configuration there should be only one definition of
+ * the same. if values are independent of the board, this definition will be
+ * present in this file if values are dependent on the board, then this should
+ * go into corresponding mem-boardName.h file
+ *
+ * Currently valid part Names are (PART):
+ * M_NAND - Micron NAND
+ * STNOR - STMicrolelctronics M29W128GL
+ */
+#define GPMC_SIZE_256M 0x0
+#define GPMC_SIZE_128M 0x8
+#define GPMC_SIZE_64M 0xC
+#define GPMC_SIZE_32M 0xE
+#define GPMC_SIZE_16M 0xF
+
+#define M_NAND_GPMC_CONFIG1 0x00000800
+#define M_NAND_GPMC_CONFIG2 0x001e1e00
+#define M_NAND_GPMC_CONFIG3 0x001e1e00
+#define M_NAND_GPMC_CONFIG4 0x16051807
+#define M_NAND_GPMC_CONFIG5 0x00151e1e
+#define M_NAND_GPMC_CONFIG6 0x16000f80
+#define M_NAND_GPMC_CONFIG7 0x00000008
+
+#define STNOR_GPMC_CONFIG1 0x00001200
+#define STNOR_GPMC_CONFIG2 0x00101000
+#define STNOR_GPMC_CONFIG3 0x00030301
+#define STNOR_GPMC_CONFIG4 0x10041004
+#define STNOR_GPMC_CONFIG5 0x000C1010
+#define STNOR_GPMC_CONFIG6 0x08070280
+#define STNOR_GPMC_CONFIG7 0x00000F48
+
+/* max number of GPMC Chip Selects */
+#define GPMC_MAX_CS 8
+/* max number of GPMC regs */
+#define GPMC_MAX_REG 7
+
+#endif /* endif _MEM_H_ */
diff --git a/arch/arm/include/asm/arch-omap5/omap.h b/arch/arm/include/asm/arch-omap5/omap.h
index e35a81a..b9600cf 100644
--- a/arch/arm/include/asm/arch-omap5/omap.h
+++ b/arch/arm/include/asm/arch-omap5/omap.h
@@ -23,11 +23,6 @@
#define OMAP54XX_L4_WKUP_BASE 0x4Ae00000
#define OMAP54XX_L4_PER_BASE 0x48000000
-#define OMAP54XX_DRAM_ADDR_SPACE_START 0x80000000
-#define OMAP54XX_DRAM_ADDR_SPACE_END 0xFFFFFFFF
-#define DRAM_ADDR_SPACE_START OMAP54XX_DRAM_ADDR_SPACE_START
-#define DRAM_ADDR_SPACE_END OMAP54XX_DRAM_ADDR_SPACE_END
-
/* CONTROL ID CODE */
#define CONTROL_CORE_ID_CODE 0x4A002204
#define CONTROL_WKUP_ID_CODE 0x4AE0C204
@@ -45,6 +40,7 @@
#define OMAP5432_CONTROL_ID_CODE_ES2_0 0x1B99802F
#define DRA752_CONTROL_ID_CODE_ES1_0 0x0B99002F
#define DRA752_CONTROL_ID_CODE_ES1_1 0x1B99002F
+#define DRA722_CONTROL_ID_CODE_ES1_0 0x0B9BC02F
/* UART */
#define UART1_BASE (OMAP54XX_L4_PER_BASE + 0x6a000)
@@ -60,9 +56,6 @@
/* Watchdog Timer2 - MPU watchdog */
#define WDT2_BASE (OMAP54XX_L4_WKUP_BASE + 0x14000)
-/* GPMC */
-#define OMAP54XX_GPMC_BASE 0x50000000
-
/* QSPI */
#define QSPI_BASE 0x4B300000
diff --git a/arch/arm/include/asm/arch-omap5/sys_proto.h b/arch/arm/include/asm/arch-omap5/sys_proto.h
index bf12c73..1038303 100644
--- a/arch/arm/include/asm/arch-omap5/sys_proto.h
+++ b/arch/arm/include/asm/arch-omap5/sys_proto.h
@@ -14,6 +14,7 @@
#include <asm/omap_common.h>
#include <linux/mtd/omap_gpmc.h>
#include <asm/arch/clock.h>
+#include <asm/ti-common/sys_proto.h>
DECLARE_GLOBAL_DATA_PTR;
@@ -56,55 +57,6 @@ void get_ioregs(const struct ctrl_ioregs **regs);
void srcomp_enable(void);
void setup_warmreset_time(void);
-static inline u32 running_from_sdram(void)
-{
- u32 pc;
- asm volatile ("mov %0, pc" : "=r" (pc));
- return ((pc >= OMAP54XX_DRAM_ADDR_SPACE_START) &&
- (pc < OMAP54XX_DRAM_ADDR_SPACE_END));
-}
-
-static inline u8 uboot_loaded_by_spl(void)
-{
- /*
- * u-boot can be running from sdram either because of configuration
- * Header or by SPL. If because of CH, then the romcode sets the
- * CHSETTINGS executed bit to true in the boot parameter structure that
- * it passes to the bootloader.This parameter is stored in the ch_flags
- * variable by both SPL and u-boot.Check out for CHSETTINGS, which is a
- * mandatory section if CH is present.
- */
- if ((gd->arch.omap_boot_params.ch_flags) & (CH_FLAGS_CHSETTINGS))
- return 0;
- else
- return running_from_sdram();
-}
-/*
- * The basic hardware init of OMAP(s_init()) can happen in 4
- * different contexts:
- * 1. SPL running from SRAM
- * 2. U-Boot running from FLASH
- * 3. Non-XIP U-Boot loaded to SDRAM by SPL
- * 4. Non-XIP U-Boot loaded to SDRAM by ROM code using the
- * Configuration Header feature
- *
- * This function finds this context.
- * Defining as inline may help in compiling out unused functions in SPL
- */
-static inline u32 omap_hw_init_context(void)
-{
-#ifdef CONFIG_SPL_BUILD
- return OMAP_INIT_CONTEXT_SPL;
-#else
- if (uboot_loaded_by_spl())
- return OMAP_INIT_CONTEXT_UBOOT_AFTER_SPL;
- else if (running_from_sdram())
- return OMAP_INIT_CONTEXT_UBOOT_AFTER_CH;
- else
- return OMAP_INIT_CONTEXT_UBOOT_FROM_NOR;
-#endif
-}
-
static inline u32 div_round_up(u32 num, u32 den)
{
return (num + den - 1)/den;
diff --git a/arch/arm/include/asm/arch-rmobile/r8a7790-gpio.h b/arch/arm/include/asm/arch-rmobile/r8a7790-gpio.h
index 444e361..74b5f1d 100644
--- a/arch/arm/include/asm/arch-rmobile/r8a7790-gpio.h
+++ b/arch/arm/include/asm/arch-rmobile/r8a7790-gpio.h
@@ -1,5 +1,5 @@
-#ifndef __ASM_R8A7790_H__
-#define __ASM_R8A7790_H__
+#ifndef __ASM_R8A7790_GPIO_H__
+#define __ASM_R8A7790_GPIO_H__
/* Pin Function Controller:
* GPIO_FN_xx - GPIO used to select pin function
@@ -384,4 +384,4 @@ enum {
GPIO_FN_TCLK1_B,
};
-#endif /* __ASM_R8A7790_H__ */
+#endif /* __ASM_R8A7790_GPIO_H__ */
diff --git a/arch/arm/include/asm/arch-rmobile/r8a7791-gpio.h b/arch/arm/include/asm/arch-rmobile/r8a7791-gpio.h
index d3cf0c1..42e8259 100644
--- a/arch/arm/include/asm/arch-rmobile/r8a7791-gpio.h
+++ b/arch/arm/include/asm/arch-rmobile/r8a7791-gpio.h
@@ -1,5 +1,5 @@
-#ifndef __ASM_R8A7791_H__
-#define __ASM_R8A7791_H__
+#ifndef __ASM_R8A7791_GPIO_H__
+#define __ASM_R8A7791_GPIO_H__
/* Pin Function Controller:
* GPIO_FN_xx - GPIO used to select pin function
@@ -435,4 +435,4 @@ enum {
GPIO_FN_MLB_DAT, GPIO_FN_CAN1_RX_B,
};
-#endif /* __ASM_R8A7791_H__ */
+#endif /* __ASM_R8A7791_GPIO_H__ */
diff --git a/arch/arm/include/asm/arch-rmobile/r8a7791.h b/arch/arm/include/asm/arch-rmobile/r8a7791.h
index 4791825..592c524 100644
--- a/arch/arm/include/asm/arch-rmobile/r8a7791.h
+++ b/arch/arm/include/asm/arch-rmobile/r8a7791.h
@@ -45,6 +45,7 @@
#define DBSC3_1_QOS_W13_BASE 0xE67A2D00
#define DBSC3_1_QOS_W14_BASE 0xE67A2E00
#define DBSC3_1_QOS_W15_BASE 0xE67A2F00
+#define DBSC3_1_DBADJ2 0xE67A00C8
#define R8A7791_CUT_ES2X 2
#define IS_R8A7791_ES2() \
diff --git a/arch/arm/include/asm/arch-rmobile/rcar-base.h b/arch/arm/include/asm/arch-rmobile/rcar-base.h
index 4331d31..41240f3 100644
--- a/arch/arm/include/asm/arch-rmobile/rcar-base.h
+++ b/arch/arm/include/asm/arch-rmobile/rcar-base.h
@@ -21,6 +21,14 @@
#define GPIO5_BASE 0xE6055000
#define SH_QSPI_BASE 0xE6B10000
+/* SCIF */
+#define SCIF0_BASE 0xE6E60000
+#define SCIF1_BASE 0xE6E68000
+#define SCIF2_BASE 0xE6E58000
+#define SCIF3_BASE 0xE6EA8000
+#define SCIF4_BASE 0xE6EE0000
+#define SCIF5_BASE 0xE6EE8000
+
#define S3C_BASE 0xE6784000
#define S3C_INT_BASE 0xE6784A00
#define S3C_MEDIA_BASE 0xE6784B00
diff --git a/arch/arm/include/asm/arch-zynq/hardware.h b/arch/arm/include/asm/arch-zynq/hardware.h
index 39184da..2aede0c 100644
--- a/arch/arm/include/asm/arch-zynq/hardware.h
+++ b/arch/arm/include/asm/arch-zynq/hardware.h
@@ -22,9 +22,12 @@
#define ZYNQ_SPI_BASEADDR0 0xE0006000
#define ZYNQ_SPI_BASEADDR1 0xE0007000
#define ZYNQ_DDRC_BASEADDR 0xF8006000
+#define ZYNQ_EFUSE_BASEADDR 0xF800D000
+#define ZYNQ_USB_BASEADDR0 0xE0002000
+#define ZYNQ_USB_BASEADDR1 0xE0003000
/* Bootmode setting values */
-#define ZYNQ_BM_MASK 0xF
+#define ZYNQ_BM_MASK 0x7
#define ZYNQ_BM_NOR 0x2
#define ZYNQ_BM_SD 0x5
#define ZYNQ_BM_JTAG 0x0
@@ -130,4 +133,12 @@ struct ddrc_regs {
};
#define ddrc_base ((struct ddrc_regs *)ZYNQ_DDRC_BASEADDR)
+struct efuse_reg {
+ u32 reserved1[4];
+ u32 status;
+ u32 reserved2[3];
+};
+
+#define efuse_base ((struct efuse_reg *)ZYNQ_EFUSE_BASEADDR)
+
#endif /* _ASM_ARCH_HARDWARE_H */
diff --git a/arch/arm/include/asm/arch-zynq/sys_proto.h b/arch/arm/include/asm/arch-zynq/sys_proto.h
index a68e1b3..53c30ec 100644
--- a/arch/arm/include/asm/arch-zynq/sys_proto.h
+++ b/arch/arm/include/asm/arch-zynq/sys_proto.h
@@ -15,7 +15,9 @@ extern void zynq_slcr_devcfg_disable(void);
extern void zynq_slcr_devcfg_enable(void);
extern u32 zynq_slcr_get_boot_mode(void);
extern u32 zynq_slcr_get_idcode(void);
+extern int zynq_slcr_get_mio_pin_status(const char *periph);
extern void zynq_ddrc_init(void);
+extern unsigned int zynq_get_silicon_version(void);
/* Driver extern functions */
extern int zynq_sdhci_init(u32 regbase);
diff --git a/arch/arm/include/asm/omap_common.h b/arch/arm/include/asm/omap_common.h
index 729723a..d1344ee 100644
--- a/arch/arm/include/asm/omap_common.h
+++ b/arch/arm/include/asm/omap_common.h
@@ -576,12 +576,6 @@ s8 abb_setup_ldovbb(u32 fuse, u32 ldovbb);
void usb_fake_mac_from_die_id(u32 *id);
-/* HW Init Context */
-#define OMAP_INIT_CONTEXT_SPL 0
-#define OMAP_INIT_CONTEXT_UBOOT_FROM_NOR 1
-#define OMAP_INIT_CONTEXT_UBOOT_AFTER_SPL 2
-#define OMAP_INIT_CONTEXT_UBOOT_AFTER_CH 3
-
/* ABB */
#define OMAP_ABB_NOMINAL_OPP 0
#define OMAP_ABB_FAST_OPP 1
@@ -645,6 +639,7 @@ static inline u8 is_dra7xx(void)
/* DRA7XX */
#define DRA752_ES1_0 0x07520100
#define DRA752_ES1_1 0x07520110
+#define DRA722_ES1_0 0x07220100
/*
* SRAM scratch space entries
diff --git a/arch/arm/include/asm/ti-common/sys_proto.h b/arch/arm/include/asm/ti-common/sys_proto.h
new file mode 100644
index 0000000..d3ab75f
--- /dev/null
+++ b/arch/arm/include/asm/ti-common/sys_proto.h
@@ -0,0 +1,72 @@
+/*
+ * (C) Copyright 2014
+ * Texas Instruments, <www.ti.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+#ifndef _TI_COMMON_SYS_PROTO_H_
+#define _TI_COMMON_SYS_PROTO_H_
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#ifdef CONFIG_OMAP_COMMON
+#define TI_ARMV7_DRAM_ADDR_SPACE_START 0x80000000
+#define TI_ARMV7_DRAM_ADDR_SPACE_END 0xFFFFFFFF
+
+#define OMAP_INIT_CONTEXT_SPL 0
+#define OMAP_INIT_CONTEXT_UBOOT_FROM_NOR 1
+#define OMAP_INIT_CONTEXT_UBOOT_AFTER_SPL 2
+#define OMAP_INIT_CONTEXT_UBOOT_AFTER_CH 3
+
+static inline u32 running_from_sdram(void)
+{
+ u32 pc;
+ asm volatile ("mov %0, pc" : "=r" (pc));
+ return ((pc >= TI_ARMV7_DRAM_ADDR_SPACE_START) &&
+ (pc < TI_ARMV7_DRAM_ADDR_SPACE_END));
+}
+
+static inline u8 uboot_loaded_by_spl(void)
+{
+ /*
+ * u-boot can be running from sdram either because of configuration
+ * Header or by SPL. If because of CH, then the romcode sets the
+ * CHSETTINGS executed bit to true in the boot parameter structure that
+ * it passes to the bootloader.This parameter is stored in the ch_flags
+ * variable by both SPL and u-boot.Check out for CHSETTINGS, which is a
+ * mandatory section if CH is present.
+ */
+ if ((gd->arch.omap_boot_params.ch_flags) & (CH_FLAGS_CHSETTINGS))
+ return 0;
+ else
+ return running_from_sdram();
+}
+
+/*
+ * The basic hardware init of OMAP(s_init()) can happen in 4
+ * different contexts:
+ * 1. SPL running from SRAM
+ * 2. U-Boot running from FLASH
+ * 3. Non-XIP U-Boot loaded to SDRAM by SPL
+ * 4. Non-XIP U-Boot loaded to SDRAM by ROM code using the
+ * Configuration Header feature
+ *
+ * This function finds this context.
+ * Defining as inline may help in compiling out unused functions in SPL
+ */
+static inline u32 omap_hw_init_context(void)
+{
+#ifdef CONFIG_SPL_BUILD
+ return OMAP_INIT_CONTEXT_SPL;
+#else
+ if (uboot_loaded_by_spl())
+ return OMAP_INIT_CONTEXT_UBOOT_AFTER_SPL;
+ else if (running_from_sdram())
+ return OMAP_INIT_CONTEXT_UBOOT_AFTER_CH;
+ else
+ return OMAP_INIT_CONTEXT_UBOOT_FROM_NOR;
+#endif
+}
+#endif
+
+#endif
diff --git a/board/compulab/cm_t54/Makefile b/board/compulab/cm_t54/Makefile
new file mode 100644
index 0000000..298ddd2
--- /dev/null
+++ b/board/compulab/cm_t54/Makefile
@@ -0,0 +1,10 @@
+#
+# Copyright (C) 2014 Compulab Ltd - http://compulab.co.il/
+#
+# Author: Dmitry Lifshitz <lifshitz@compulab.co.il>
+#
+# SPDX-License-Identifier: GPL-2.0+
+#
+
+obj-y += cm_t54.o
+obj-$(CONFIG_SPL_BUILD) += mux.o spl.o
diff --git a/board/compulab/cm_t54/cm_t54.c b/board/compulab/cm_t54/cm_t54.c
new file mode 100644
index 0000000..fadfddc
--- /dev/null
+++ b/board/compulab/cm_t54/cm_t54.c
@@ -0,0 +1,262 @@
+/*
+ * Board functions for Compulab CM-T54 board
+ *
+ * Copyright (C) 2014, Compulab Ltd - http://compulab.co.il/
+ *
+ * Author: Dmitry Lifshitz <lifshitz@compulab.co.il>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <fdt_support.h>
+#include <usb.h>
+#include <mmc.h>
+#include <palmas.h>
+#include <spl.h>
+
+#include <asm/gpio.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/arch/mmc_host_def.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/ehci.h>
+#include <asm/ehci-omap.h>
+
+#include "../common/eeprom.h"
+
+#define DIE_ID_REG_BASE (OMAP54XX_L4_CORE_BASE + 0x2000)
+#define DIE_ID_REG_OFFSET 0x200
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#if !defined(CONFIG_SPL_BUILD)
+inline void set_muxconf_regs_essential(void){};
+#endif
+
+const struct omap_sysinfo sysinfo = {
+ "Board: CM-T54\n"
+};
+
+/*
+ * Routine: board_init
+ * Description: hardware init.
+ */
+int board_init(void)
+{
+ gd->bd->bi_boot_params = (CONFIG_SYS_SDRAM_BASE + 0x100); /* boot param addr */
+
+ return 0;
+}
+
+/*
+ * Routine: cm_t54_palmas_regulator_set
+ * Description: select voltage and turn on/off Palmas PMIC regulator.
+ */
+static int cm_t54_palmas_regulator_set(u8 vreg, u8 vval, u8 creg, u8 cval)
+{
+ int err;
+
+ /* Setup voltage */
+ err = palmas_i2c_write_u8(TWL603X_CHIP_P1, vreg, vval);
+ if (err) {
+ printf("cm_t54: could not set regulator 0x%02x voltage : %d\n",
+ vreg, err);
+ return err;
+ }
+
+ /* Turn on/off regulator */
+ err = palmas_i2c_write_u8(TWL603X_CHIP_P1, creg, cval);
+ if (err) {
+ printf("cm_t54: could not turn on/off regulator 0x%02x : %d\n",
+ creg, err);
+ return err;
+ }
+
+ return 0;
+}
+
+/*
+ * Routine: mmc_get_env_part
+ * Description: setup environment storage device partition.
+ */
+#ifdef CONFIG_SYS_MMC_ENV_PART
+uint mmc_get_env_part(struct mmc *mmc)
+{
+ u32 bootmode = gd->arch.omap_boot_params.omap_bootmode;
+ uint bootpart = CONFIG_SYS_MMC_ENV_PART;
+
+ /*
+ * If booted from eMMC boot partition then force eMMC
+ * FIRST boot partition to be env storage
+ */
+ if (bootmode == BOOT_DEVICE_MMC2_2)
+ bootpart = 1;
+
+ return bootpart;
+}
+#endif
+
+#if defined(CONFIG_GENERIC_MMC) && !defined(CONFIG_SPL_BUILD)
+#define SB_T54_CD_GPIO 228
+#define SB_T54_WP_GPIO 229
+
+int board_mmc_getcd(struct mmc *mmc)
+{
+ return !gpio_get_value(SB_T54_CD_GPIO);
+}
+
+int board_mmc_init(bd_t *bis)
+{
+ int ret0, ret1;
+
+ ret0 = omap_mmc_init(0, 0, 0, -1, SB_T54_WP_GPIO);
+ if (ret0)
+ printf("cm_t54: failed to initialize mmc0\n");
+
+ ret1 = omap_mmc_init(1, 0, 0, -1, -1);
+ if (ret1)
+ printf("cm_t54: failed to initialize mmc1\n");
+
+ if (ret0 && ret1)
+ return -1;
+
+ return 0;
+}
+#endif
+
+#ifdef CONFIG_USB_HOST_ETHER
+
+void ft_board_setup(void *blob, bd_t *bd)
+{
+ uint8_t enetaddr[6];
+
+ /* MAC addr */
+ if (eth_getenv_enetaddr("usbethaddr", enetaddr)) {
+ fdt_find_and_setprop(blob, "/smsc95xx@0", "mac-address",
+ enetaddr, 6, 1);
+ }
+}
+
+static void generate_mac_addr(uint8_t *enetaddr)
+{
+ int reg;
+
+ reg = DIE_ID_REG_BASE + DIE_ID_REG_OFFSET;
+
+ /*
+ * create a fake MAC address from the processor ID code.
+ * first byte is 0x02 to signify locally administered.
+ */
+ enetaddr[0] = 0x02;
+ enetaddr[1] = readl(reg + 0x10) & 0xff;
+ enetaddr[2] = readl(reg + 0xC) & 0xff;
+ enetaddr[3] = readl(reg + 0x8) & 0xff;
+ enetaddr[4] = readl(reg) & 0xff;
+ enetaddr[5] = (readl(reg) >> 8) & 0xff;
+}
+
+/*
+ * Routine: handle_mac_address
+ * Description: prepare MAC address for on-board Ethernet.
+ */
+static int handle_mac_address(void)
+{
+ uint8_t enetaddr[6];
+ int ret;
+
+ ret = eth_getenv_enetaddr("usbethaddr", enetaddr);
+ if (ret)
+ return 0;
+
+ ret = cl_eeprom_read_mac_addr(enetaddr);
+ if (!ret || !is_valid_ether_addr(enetaddr))
+ generate_mac_addr(enetaddr);
+
+ if (!is_valid_ether_addr(enetaddr))
+ return -1;
+
+ return eth_setenv_enetaddr("usbethaddr", enetaddr);
+}
+
+int board_eth_init(bd_t *bis)
+{
+ return handle_mac_address();
+}
+#endif
+
+#ifdef CONFIG_USB_EHCI
+static struct omap_usbhs_board_data usbhs_bdata = {
+ .port_mode[0] = OMAP_USBHS_PORT_MODE_UNUSED,
+ .port_mode[1] = OMAP_EHCI_PORT_MODE_HSIC,
+ .port_mode[2] = OMAP_EHCI_PORT_MODE_HSIC,
+};
+
+static void setup_host_clocks(bool enable)
+{
+ int usbhost_clk = OPTFCLKEN_HSIC60M_P3_CLK |
+ OPTFCLKEN_HSIC480M_P3_CLK |
+ OPTFCLKEN_HSIC60M_P2_CLK |
+ OPTFCLKEN_HSIC480M_P2_CLK |
+ OPTFCLKEN_UTMI_P3_CLK |
+ OPTFCLKEN_UTMI_P2_CLK;
+
+ int usbtll_clk = OPTFCLKEN_USB_CH1_CLK_ENABLE |
+ OPTFCLKEN_USB_CH2_CLK_ENABLE;
+
+ int usbhub_clk = CKOBUFFER_CLK_ENABLE_MASK;
+
+ if (enable) {
+ /* Enable port 2 and 3 clocks*/
+ setbits_le32((*prcm)->cm_l3init_hsusbhost_clkctrl, usbhost_clk);
+ /* Enable port 2 and 3 usb host ports tll clocks*/
+ setbits_le32((*prcm)->cm_l3init_hsusbtll_clkctrl, usbtll_clk);
+ /* Request FREF_XTAL_CLK clock for HSIC USB Hub */
+ setbits_le32((*ctrl)->control_ckobuffer, usbhub_clk);
+ } else {
+ clrbits_le32((*ctrl)->control_ckobuffer, usbhub_clk);
+ clrbits_le32((*prcm)->cm_l3init_hsusbtll_clkctrl, usbtll_clk);
+ clrbits_le32((*prcm)->cm_l3init_hsusbhost_clkctrl, usbhost_clk);
+ }
+}
+
+int ehci_hcd_init(int index, enum usb_init_type init,
+ struct ehci_hccr **hccr, struct ehci_hcor **hcor)
+{
+ int ret;
+
+ /* VCC_3V3_ETH */
+ cm_t54_palmas_regulator_set(SMPS9_VOLTAGE, SMPS_VOLT_3V3, SMPS9_CTRL,
+ SMPS_MODE_SLP_AUTO | SMPS_MODE_ACT_AUTO);
+
+ setup_host_clocks(true);
+
+ ret = omap_ehci_hcd_init(index, &usbhs_bdata, hccr, hcor);
+ if (ret < 0)
+ printf("cm_t54: Failed to initialize ehci : %d\n", ret);
+
+ return ret;
+}
+
+int ehci_hcd_stop(void)
+{
+ int ret = omap_ehci_hcd_stop();
+
+ setup_host_clocks(false);
+
+ cm_t54_palmas_regulator_set(SMPS9_VOLTAGE, SMPS_VOLT_OFF,
+ SMPS9_CTRL, SMPS_MODE_SLP_AUTO);
+
+ return ret;
+}
+
+void usb_hub_reset_devices(int port)
+{
+ /* The LAN9730 needs to be reset after the port power has been set. */
+ if (port == 3) {
+ gpio_direction_output(CONFIG_OMAP_EHCI_PHY3_RESET_GPIO, 0);
+ udelay(10);
+ gpio_direction_output(CONFIG_OMAP_EHCI_PHY3_RESET_GPIO, 1);
+ }
+}
+#endif
+
diff --git a/board/compulab/cm_t54/mux.c b/board/compulab/cm_t54/mux.c
new file mode 100644
index 0000000..da35383
--- /dev/null
+++ b/board/compulab/cm_t54/mux.c
@@ -0,0 +1,94 @@
+/*
+ * Pinmux configuration for Compulab CM-T54 board
+ *
+ * Copyright (C) 2014, Compulab Ltd - http://compulab.co.il/
+ *
+ * Author: Dmitry Lifshitz <lifshitz@compulab.co.il>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef _CM_T54_MUX_DATA_H
+#define _CM_T54_MUX_DATA_H
+
+#include <asm/arch/mux_omap5.h>
+#include <asm/arch/sys_proto.h>
+
+const struct pad_conf_entry core_padconf_array_essential[] = {
+ /* MMC1 - SD CARD */
+ {SDCARD_CLK, (PTU | IEN | M0)}, /* SDCARD_CLK */
+ {SDCARD_CMD, (PTU | IEN | M0)}, /* SDCARD_CMD */
+ {SDCARD_DATA0, (PTU | IEN | M0)}, /* SDCARD_DATA0 */
+ {SDCARD_DATA1, (PTU | IEN | M0)}, /* SDCARD_DATA1 */
+ {SDCARD_DATA2, (PTU | IEN | M0)}, /* SDCARD_DATA2 */
+ {SDCARD_DATA3, (PTU | IEN | M0)}, /* SDCARD_DATA3 */
+
+ /* SD CARD CD and WP GPIOs*/
+ {TIMER5_PWM_EVT, (PTU | IEN | M6)}, /* GPIO8_228 */
+ {TIMER6_PWM_EVT, (PTU | IEN | M6)}, /* GPIO8_229 */
+
+ /* MMC2 - eMMC */
+ {EMMC_CLK, (PTU | IEN | M0)}, /* EMMC_CLK */
+ {EMMC_CMD, (PTU | IEN | M0)}, /* EMMC_CMD */
+ {EMMC_DATA0, (PTU | IEN | M0)}, /* EMMC_DATA0 */
+ {EMMC_DATA1, (PTU | IEN | M0)}, /* EMMC_DATA1 */
+ {EMMC_DATA2, (PTU | IEN | M0)}, /* EMMC_DATA2 */
+ {EMMC_DATA3, (PTU | IEN | M0)}, /* EMMC_DATA3 */
+ {EMMC_DATA4, (PTU | IEN | M0)}, /* EMMC_DATA4 */
+ {EMMC_DATA5, (PTU | IEN | M0)}, /* EMMC_DATA5 */
+ {EMMC_DATA6, (PTU | IEN | M0)}, /* EMMC_DATA6 */
+ {EMMC_DATA7, (PTU | IEN | M0)}, /* EMMC_DATA7 */
+
+ /* UART4 */
+ {I2C5_SCL, (PTU | IEN | M2)}, /* UART4_RX */
+ {I2C5_SDA, (M2)}, /* UART4_TX */
+
+ /* Led */
+ {HSI2_CAFLAG, (PTU | M6)}, /* GPIO3_80 */
+
+ /* I2C1 */
+ {I2C1_PMIC_SCL, (PTU | IEN | M0)}, /* I2C1_PMIC_SCL */
+ {I2C1_PMIC_SDA, (PTU | IEN | M0)}, /* I2C1_PMIC_SDA */
+
+ /* USBB2, USBB3 */
+ {USBB2_HSIC_STROBE, (PTU | IEN | M0)}, /* USBB2_HSIC_STROBE */
+ {USBB2_HSIC_DATA, (PTU | IEN | M0)}, /* USBB2_HSIC_DATA */
+ {USBB3_HSIC_STROBE, (PTU | IEN | M0)}, /* USBB3_HSIC_STROBE */
+ {USBB3_HSIC_DATA, (PTU | IEN | M0)}, /* USBB3_HSIC_DATA */
+
+ /* USB Hub and USB Eth reset GPIOs */
+ {HSI2_CAREADY, (PTD | M6)}, /* GPIO3_76 */
+ {HSI2_ACDATA, (PTD | M6)}, /* GPIO3_83 */
+
+ /* I2C4 */
+ {I2C4_SCL, (PTU | IEN | M0)}, /* I2C4_SCL */
+ {I2C4_SDA, (PTU | IEN | M0)}, /* I2C4_SDA */
+};
+
+const struct pad_conf_entry wkup_padconf_array_essential[] = {
+ {SR_PMIC_SCL, (PTU | IEN | M0)}, /* SR_PMIC_SCL */
+ {SR_PMIC_SDA, (PTU | IEN | M0)}, /* SR_PMIC_SDA */
+ {SYS_32K, (IEN | M0)}, /* SYS_32K */
+
+ /* USB Hub clock */
+ {FREF_CLK1_OUT, (PTD | IEN | M0)}, /* FREF_CLK1_OUT */
+};
+
+/*
+ * Routine: set_muxconf_regs_essential
+ * Description: setup board pinmux configuration.
+ */
+void set_muxconf_regs_essential(void)
+{
+ do_set_mux((*ctrl)->control_padconf_core_base,
+ core_padconf_array_essential,
+ sizeof(core_padconf_array_essential) /
+ sizeof(struct pad_conf_entry));
+
+ do_set_mux((*ctrl)->control_padconf_wkup_base,
+ wkup_padconf_array_essential,
+ sizeof(wkup_padconf_array_essential) /
+ sizeof(struct pad_conf_entry));
+}
+
+#endif /* _CM_T54_MUX_DATA_H */
diff --git a/board/compulab/cm_t54/spl.c b/board/compulab/cm_t54/spl.c
new file mode 100644
index 0000000..5c7b2c8
--- /dev/null
+++ b/board/compulab/cm_t54/spl.c
@@ -0,0 +1,66 @@
+/*
+ * SPL specific code for Compulab CM-T54 board
+ *
+ * Copyright (C) 2014, Compulab Ltd - http://compulab.co.il/
+ *
+ * Author: Dmitry Lifshitz <lifshitz@compulab.co.il>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <asm/emif.h>
+
+const struct emif_regs emif_regs_ddr3_532_mhz_cm_t54 = {
+#if defined(CONFIG_DRAM_1G) || defined(CONFIG_DRAM_512M)
+ .sdram_config_init = 0x618522B2,
+ .sdram_config = 0x618522B2,
+#elif defined(CONFIG_DRAM_2G)
+ .sdram_config_init = 0x618522BA,
+ .sdram_config = 0x618522BA,
+#endif
+ .sdram_config2 = 0x0,
+ .ref_ctrl = 0x00001040,
+ .sdram_tim1 = 0xEEEF36F3,
+ .sdram_tim2 = 0x348F7FDA,
+ .sdram_tim3 = 0x027F88A8,
+ .read_idle_ctrl = 0x00050000,
+ .zq_config = 0x1007190B,
+ .temp_alert_config = 0x00000000,
+
+ .emif_ddr_phy_ctlr_1_init = 0x0030400B,
+ .emif_ddr_phy_ctlr_1 = 0x0034400B,
+ .emif_ddr_ext_phy_ctrl_1 = 0x04040100,
+ .emif_ddr_ext_phy_ctrl_2 = 0x00000000,
+ .emif_ddr_ext_phy_ctrl_3 = 0x00000000,
+ .emif_ddr_ext_phy_ctrl_4 = 0x00000000,
+ .emif_ddr_ext_phy_ctrl_5 = 0x4350D435,
+ .emif_rd_wr_lvl_rmp_win = 0x00000000,
+ .emif_rd_wr_lvl_rmp_ctl = 0x80000000,
+ .emif_rd_wr_lvl_ctl = 0x00000000,
+ .emif_rd_wr_exec_thresh = 0x40000305,
+};
+
+const struct dmm_lisa_map_regs lisa_map_cm_t54 = {
+ .dmm_lisa_map_0 = 0x0,
+ .dmm_lisa_map_1 = 0x0,
+
+#ifdef CONFIG_DRAM_2G
+ .dmm_lisa_map_2 = 0x80740300,
+#elif defined(CONFIG_DRAM_1G)
+ .dmm_lisa_map_2 = 0x80640300,
+#elif defined(CONFIG_DRAM_512M)
+ .dmm_lisa_map_2 = 0x80500100,
+#endif
+ .dmm_lisa_map_3 = 0x00000000,
+ .is_ma_present = 0x1,
+};
+
+void emif_get_reg_dump(u32 emif_nr, const struct emif_regs **regs)
+{
+ *regs = &emif_regs_ddr3_532_mhz_cm_t54;
+}
+
+void emif_get_dmm_regs(const struct dmm_lisa_map_regs **dmm_lisa_regs)
+{
+ *dmm_lisa_regs = &lisa_map_cm_t54;
+}
diff --git a/board/compulab/common/Makefile b/board/compulab/common/Makefile
index 6d7d068..4044ac9 100644
--- a/board/compulab/common/Makefile
+++ b/board/compulab/common/Makefile
@@ -6,5 +6,5 @@
# SPDX-License-Identifier: GPL-2.0+
#
-obj-$(CONFIG_SYS_I2C_OMAP34XX) += eeprom.o
+obj-$(CONFIG_SYS_I2C) += eeprom.o
obj-$(CONFIG_LCD) += omap3_display.o
diff --git a/board/compulab/common/eeprom.c b/board/compulab/common/eeprom.c
index 5aa3dbd..20fe3e1 100644
--- a/board/compulab/common/eeprom.c
+++ b/board/compulab/common/eeprom.c
@@ -10,6 +10,11 @@
#include <common.h>
#include <i2c.h>
+#ifndef CONFIG_SYS_I2C_EEPROM_ADDR
+# define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
+# define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
+#endif
+
#define EEPROM_LAYOUT_VER_OFFSET 44
#define BOARD_SERIAL_OFFSET 20
#define BOARD_SERIAL_OFFSET_LEGACY 8
diff --git a/board/compulab/common/eeprom.h b/board/compulab/common/eeprom.h
index e871629..85d5bf0 100644
--- a/board/compulab/common/eeprom.h
+++ b/board/compulab/common/eeprom.h
@@ -10,7 +10,7 @@
#ifndef _EEPROM_
#define _EEPROM_
-#ifdef CONFIG_SYS_I2C_OMAP34XX
+#ifdef CONFIG_SYS_I2C
int cl_eeprom_read_mac_addr(uchar *buf);
u32 cl_eeprom_get_board_rev(void);
#else
diff --git a/board/gumstix/duovero/Makefile b/board/gumstix/duovero/Makefile
new file mode 100644
index 0000000..f738c58
--- /dev/null
+++ b/board/gumstix/duovero/Makefile
@@ -0,0 +1,8 @@
+#
+# (C) Copyright 2000, 2001, 2002
+# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+#
+# SPDX-License-Identifier: GPL-2.0+
+#
+
+obj-y := duovero.o
diff --git a/board/gumstix/duovero/duovero.c b/board/gumstix/duovero/duovero.c
new file mode 100644
index 0000000..81d6c82
--- /dev/null
+++ b/board/gumstix/duovero/duovero.c
@@ -0,0 +1,264 @@
+/*
+ * (C) Copyright 2013
+ * Gumstix Inc. <www.gumstix.com>
+ * Maintainer: Ash Charles <ash@gumstix.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+#include <common.h>
+#include <netdev.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/arch/mmc_host_def.h>
+#include <twl6030.h>
+#include <asm/emif.h>
+#include <asm/arch/clock.h>
+#include <asm/arch/gpio.h>
+#include <asm/gpio.h>
+
+#include "duovero_mux_data.h"
+
+#define WIFI_EN 43
+
+#if defined(CONFIG_CMD_NET)
+#define SMSC_NRESET 45
+static void setup_net_chip(void);
+#endif
+
+#ifdef CONFIG_USB_EHCI
+#include <usb.h>
+#include <asm/arch/ehci.h>
+#include <asm/ehci-omap.h>
+#endif
+
+DECLARE_GLOBAL_DATA_PTR;
+
+const struct omap_sysinfo sysinfo = {
+ "Board: duovero\n"
+};
+
+struct omap4_scrm_regs *const scrm = (struct omap4_scrm_regs *)0x4a30a000;
+
+/**
+ * @brief board_init
+ *
+ * @return 0
+ */
+int board_init(void)
+{
+ gpmc_init();
+
+ gd->bd->bi_arch_number = MACH_TYPE_OMAP4_DUOVERO;
+ gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
+
+ return 0;
+}
+
+/**
+ * @brief misc_init_r - Configure board specific configurations
+ * such as power configurations, ethernet initialization as phase2 of
+ * boot sequence
+ *
+ * @return 0
+ */
+int misc_init_r(void)
+{
+ int ret = 0;
+ u8 val;
+
+ /* wifi setup: first enable 32Khz clock from 6030 pmic */
+ val = 0xe1;
+ ret = i2c_write(TWL6030_CHIP_PM, 0xbe, 1, &val, 1);
+ if (ret)
+ printf("Failed to enable 32Khz clock to wifi module\n");
+
+ /* then setup WIFI_EN as an output pin and send reset pulse */
+ if (!gpio_request(WIFI_EN, "")) {
+ gpio_direction_output(WIFI_EN, 0);
+ gpio_set_value(WIFI_EN, 1);
+ udelay(1);
+ gpio_set_value(WIFI_EN, 0);
+ udelay(1);
+ gpio_set_value(WIFI_EN, 1);
+ }
+
+#if defined(CONFIG_CMD_NET)
+ setup_net_chip();
+#endif
+ return 0;
+}
+
+void set_muxconf_regs_essential(void)
+{
+ do_set_mux((*ctrl)->control_padconf_core_base,
+ core_padconf_array_essential,
+ sizeof(core_padconf_array_essential) /
+ sizeof(struct pad_conf_entry));
+
+ do_set_mux((*ctrl)->control_padconf_wkup_base,
+ wkup_padconf_array_essential,
+ sizeof(wkup_padconf_array_essential) /
+ sizeof(struct pad_conf_entry));
+
+ do_set_mux((*ctrl)->control_padconf_core_base,
+ core_padconf_array_non_essential,
+ sizeof(core_padconf_array_non_essential) /
+ sizeof(struct pad_conf_entry));
+
+ do_set_mux((*ctrl)->control_padconf_wkup_base,
+ wkup_padconf_array_non_essential,
+ sizeof(wkup_padconf_array_non_essential) /
+ sizeof(struct pad_conf_entry));
+}
+
+#if !defined(CONFIG_SPL_BUILD) && defined(CONFIG_GENERIC_MMC)
+int board_mmc_init(bd_t *bis)
+{
+ return omap_mmc_init(0, 0, 0, -1, -1);
+}
+#endif
+
+
+#if defined(CONFIG_CMD_NET)
+
+#define GPMC_SIZE_16M 0xF
+#define GPMC_BASEADDR_MASK 0x3F
+#define GPMC_CS_ENABLE 0x1
+
+static void enable_gpmc_net_config(const u32 *gpmc_config, struct gpmc_cs *cs,
+ u32 base, u32 size)
+{
+ writel(0, &cs->config7);
+ sdelay(1000);
+ /* Delay for settling */
+ writel(gpmc_config[0], &cs->config1);
+ writel(gpmc_config[1], &cs->config2);
+ writel(gpmc_config[2], &cs->config3);
+ writel(gpmc_config[3], &cs->config4);
+ writel(gpmc_config[4], &cs->config5);
+ writel(gpmc_config[5], &cs->config6);
+
+ /*
+ * Enable the config. size is the CS size and goes in
+ * bits 11:8. We set bit 6 to enable this CS and the base
+ * address goes into bits 5:0.
+ */
+ writel((size << 8) | (GPMC_CS_ENABLE << 6) |
+ ((base >> 24) & GPMC_BASEADDR_MASK),
+ &cs->config7);
+
+ sdelay(2000);
+}
+
+/* GPMC CS configuration for an SMSC LAN9221 ethernet controller */
+#define NET_LAN9221_GPMC_CONFIG1 0x2a001203
+#define NET_LAN9221_GPMC_CONFIG2 0x000a0a02
+#define NET_LAN9221_GPMC_CONFIG3 0x00020200
+#define NET_LAN9221_GPMC_CONFIG4 0x0a030a03
+#define NET_LAN9221_GPMC_CONFIG5 0x000a0a0a
+#define NET_LAN9221_GPMC_CONFIG6 0x8a070707
+#define NET_LAN9221_GPMC_CONFIG7 0x00000f6c
+
+/* GPMC definitions for LAN9221 chips on expansion boards */
+static const u32 gpmc_lan_config[] = {
+ NET_LAN9221_GPMC_CONFIG1,
+ NET_LAN9221_GPMC_CONFIG2,
+ NET_LAN9221_GPMC_CONFIG3,
+ NET_LAN9221_GPMC_CONFIG4,
+ NET_LAN9221_GPMC_CONFIG5,
+ NET_LAN9221_GPMC_CONFIG6,
+ /*CONFIG7- computed as params */
+};
+
+/*
+ * Routine: setup_net_chip
+ * Description: Setting up the configuration GPMC registers specific to the
+ * Ethernet hardware.
+ */
+static void setup_net_chip(void)
+{
+ enable_gpmc_net_config(gpmc_lan_config, &gpmc_cfg->cs[5], 0x2C000000,
+ GPMC_SIZE_16M);
+
+ /* Make GPIO SMSC_NRESET as output pin and send reset pulse */
+ if (!gpio_request(SMSC_NRESET, "")) {
+ gpio_direction_output(SMSC_NRESET, 0);
+ gpio_set_value(SMSC_NRESET, 1);
+ udelay(1);
+ gpio_set_value(SMSC_NRESET, 0);
+ udelay(1);
+ gpio_set_value(SMSC_NRESET, 1);
+ }
+}
+#endif
+
+int board_eth_init(bd_t *bis)
+{
+ int rc = 0;
+#ifdef CONFIG_SMC911X
+ rc = smc911x_initialize(0, CONFIG_SMC911X_BASE);
+#endif
+ return rc;
+}
+
+#ifdef CONFIG_USB_EHCI
+
+static struct omap_usbhs_board_data usbhs_bdata = {
+ .port_mode[0] = OMAP_EHCI_PORT_MODE_PHY,
+ .port_mode[1] = OMAP_USBHS_PORT_MODE_UNUSED,
+ .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED,
+};
+
+int ehci_hcd_init(int index, enum usb_init_type init,
+ struct ehci_hccr **hccr, struct ehci_hcor **hcor)
+{
+ int ret;
+ unsigned int utmi_clk;
+ u32 auxclk, altclksrc;
+
+ /* Now we can enable our port clocks */
+ utmi_clk = readl((void *)CM_L3INIT_HSUSBHOST_CLKCTRL);
+ utmi_clk |= HSUSBHOST_CLKCTRL_CLKSEL_UTMI_P1_MASK;
+ setbits_le32((void *)CM_L3INIT_HSUSBHOST_CLKCTRL, utmi_clk);
+
+ auxclk = readl(&scrm->auxclk3);
+ /* Select sys_clk */
+ auxclk &= ~AUXCLK_SRCSELECT_MASK;
+ auxclk |= AUXCLK_SRCSELECT_SYS_CLK << AUXCLK_SRCSELECT_SHIFT;
+ /* Set the divisor to 2 */
+ auxclk &= ~AUXCLK_CLKDIV_MASK;
+ auxclk |= AUXCLK_CLKDIV_2 << AUXCLK_CLKDIV_SHIFT;
+ /* Request auxilary clock #3 */
+ auxclk |= AUXCLK_ENABLE_MASK;
+ writel(auxclk, &scrm->auxclk3);
+
+ altclksrc = readl(&scrm->altclksrc);
+
+ /* Activate alternate system clock supplier */
+ altclksrc &= ~ALTCLKSRC_MODE_MASK;
+ altclksrc |= ALTCLKSRC_MODE_ACTIVE;
+
+ /* enable clocks */
+ altclksrc |= ALTCLKSRC_ENABLE_INT_MASK | ALTCLKSRC_ENABLE_EXT_MASK;
+
+ writel(altclksrc, &scrm->altclksrc);
+
+ ret = omap_ehci_hcd_init(index, &usbhs_bdata, hccr, hcor);
+ if (ret < 0)
+ return ret;
+
+ return 0;
+}
+
+int ehci_hcd_stop(int index)
+{
+ return omap_ehci_hcd_stop();
+}
+#endif
+
+/*
+ * get_board_rev() - get board revision
+ */
+u32 get_board_rev(void)
+{
+ return 0x20;
+}
diff --git a/board/gumstix/duovero/duovero_mux_data.h b/board/gumstix/duovero/duovero_mux_data.h
new file mode 100644
index 0000000..1be247b
--- /dev/null
+++ b/board/gumstix/duovero/duovero_mux_data.h
@@ -0,0 +1,199 @@
+/*
+ * (C) Copyright 2012
+ * Gumstix Incorporated, <www.gumstix.com>
+ * Maintainer: Ash Charles <ash@gumstix.com>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+#ifndef _DUOVERO_MUX_DATA_H_
+#define _DUOVERO_MUX_DATA_H_
+
+#include <asm/arch/mux_omap4.h>
+
+const struct pad_conf_entry core_padconf_array_essential[] = {
+ {SDMMC1_CLK, (PTU | OFF_EN | OFF_OUT_PTD | M0)}, /* sdmmc1_clk */
+ {SDMMC1_CMD, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* sdmmc1_cmd */
+ {SDMMC1_DAT0, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* sdmmc1_dat0 */
+ {SDMMC1_DAT1, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* sdmmc1_dat1 */
+ {SDMMC1_DAT2, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* sdmmc1_dat2 */
+ {SDMMC1_DAT3, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* sdmmc1_dat3 */
+ {I2C1_SCL, (PTU | IEN | M0)}, /* i2c1_scl */
+ {I2C1_SDA, (PTU | IEN | M0)}, /* i2c1_sda */
+ {I2C2_SCL, (PTU | IEN | M0)}, /* i2c2_scl */
+ {I2C2_SDA, (PTU | IEN | M0)}, /* i2c2_sda */
+ {I2C3_SCL, (PTU | IEN | M0)}, /* i2c3_scl */
+ {I2C3_SDA, (PTU | IEN | M0)}, /* i2c3_sda */
+ {I2C4_SCL, (PTU | IEN | M0)}, /* i2c4_scl */
+ {I2C4_SDA, (PTU | IEN | M0)}, /* i2c4_sda */
+ {UART3_CTS_RCTX, (PTU | IEN | M0)}, /* uart3_tx */
+ {UART3_RTS_SD, (M0)}, /* uart3_rts_sd */
+ {UART3_RX_IRRX, (PTU | IEN | M0)}, /* uart3_rx */
+ {UART3_TX_IRTX, (M0)} /* uart3_tx */
+};
+
+const struct pad_conf_entry wkup_padconf_array_essential[] = {
+ {PAD1_SR_SCL, (PTU | IEN | M0)}, /* sr_scl */
+ {PAD0_SR_SDA, (PTU | IEN | M0)}, /* sr_sda */
+ {PAD1_SYS_32K, (IEN | M0)} /* sys_32k */
+};
+
+const struct pad_conf_entry core_padconf_array_non_essential[] = {
+ {GPMC_AD0, (PTU | IEN | M0)}, /* gpmc_ad0 */
+ {GPMC_AD1, (PTU | IEN | M0)}, /* gpmc_ad1 */
+ {GPMC_AD2, (PTU | IEN | M0)}, /* gpmc_ad2 */
+ {GPMC_AD3, (PTU | IEN | M0)}, /* gpmc_ad3 */
+ {GPMC_AD4, (PTU | IEN | M0)}, /* gpmc_ad4 */
+ {GPMC_AD5, (PTU | IEN | M0)}, /* gpmc_ad5 */
+ {GPMC_AD6, (PTU | IEN | M0)}, /* gpmc_ad6 */
+ {GPMC_AD7, (PTU | IEN | M0)}, /* gpmc_ad7 */
+ {GPMC_AD8, (PTU | IEN | M0)}, /* gpmc_ad8 */
+ {GPMC_AD9, (PTU | IEN | M0)}, /* gpmc_ad9 */
+ {GPMC_AD10, (PTU | IEN | M0)}, /* gpmc_ad10 */
+ {GPMC_AD11, (PTU | IEN | M0)}, /* gpmc_ad11 */
+ {GPMC_AD12, (PTU | IEN | M0)}, /* gpmc_ad12 */
+ {GPMC_AD13, (PTU | IEN | M0)}, /* gpmc_ad13 */
+ {GPMC_AD14, (PTU | IEN | M0)}, /* gpmc_ad14 */
+ {GPMC_AD15, (PTU | IEN | M0)}, /* gpmc_ad15 */
+ {GPMC_A16, (PTU | IEN | M3)}, /* gpio_40 */
+ {GPMC_A17, (PTU | IEN | M3)}, /* gpio_41 - hdmi_ls_oe */
+ {GPMC_A18, (PTU | IEN | M3)}, /* gpio_42 */
+ {GPMC_A19, (PTU | IEN | M3)}, /* gpio_43 - wifi_en */
+ {GPMC_A20, (PTU | IEN | M3)}, /* gpio_44 - eth_irq */
+ {GPMC_A21, (PTU | IEN | M3)}, /* gpio_45 - eth_nreset */
+ {GPMC_A22, (PTU | IEN | M3)}, /* gpio_46 - eth_pme */
+ {GPMC_A23, (PTU | IEN | M3)}, /* gpio_47 */
+ {GPMC_A24, (PTU | IEN | M3)}, /* gpio_48 - eth_mdix */
+ {GPMC_A25, (PTU | IEN | M3)}, /* gpio_49 - bt_wakeup */
+ {GPMC_NCS0, (PTU | M0)}, /* gpmc_ncs0 */
+ {GPMC_NCS1, (PTU | M0)}, /* gpmc_ncs1 */
+ {GPMC_NCS2, (PTU | M0)}, /* gpmc_ncs2 */
+ {GPMC_NCS3, (PTU | IEN | M3)}, /* gpio_53 */
+ {C2C_DATA12, (PTU | M0)}, /* gpmc_ncs4 */
+ {C2C_DATA13, (PTU | M0)}, /* gpmc_ncs5 - eth_cs */
+ {GPMC_NWP, (PTU | IEN | M0)}, /* gpmc_nwp */
+ {GPMC_CLK, (PTU | IEN | M0)}, /* gpmc_clk */
+ {GPMC_NADV_ALE, (PTU | M0)}, /* gpmc_nadv_ale */
+ {GPMC_NBE0_CLE, (PTU | M0)}, /* gpmc_nbe0_cle */
+ {GPMC_NBE1, (PTU | M0)}, /* gpmc_nbe1 */
+ {GPMC_WAIT0, (PTU | IEN | M0)}, /* gpmc_wait0 */
+ {GPMC_WAIT1, (PTU | IEN | M0)}, /* gpio_62 - usbh_nreset */
+ {GPMC_NOE, (PTU | M0)}, /* gpmc_noe */
+ {GPMC_NWE, (PTU | M0)}, /* gpmc_nwe */
+ {HDMI_HPD, (PTD | IEN | M3)}, /* gpio_63 - hdmi_hpd */
+ {HDMI_CEC, (PTU | IEN | M0)}, /* hdmi_cec */
+ {HDMI_DDC_SCL, (M0)}, /* hdmi_ddc_scl */
+ {HDMI_DDC_SDA, (IEN | M0)}, /* hdmi_ddc_sda */
+ {CSI21_DX0, (IEN | M0)}, /* csi21_dx0 */
+ {CSI21_DY0, (IEN | M0)}, /* csi21_dy0 */
+ {CSI21_DX1, (IEN | M0)}, /* csi21_dx1 */
+ {CSI21_DY1, (IEN | M0)}, /* csi21_dy1 */
+ {CSI21_DX2, (IEN | M0)}, /* csi21_dx2 */
+ {CSI21_DY2, (IEN | M0)}, /* csi21_dy2 */
+ {CSI21_DX3, (IEN | M0)}, /* csi21_dx3 */
+ {CSI21_DY3, (IEN | M0)}, /* csi21_dy3 */
+ {CSI21_DX4, (IEN | M0)}, /* csi21_dx4 */
+ {CSI21_DY4, (IEN | M0)}, /* csi21_dy4 */
+ {CSI22_DX0, (IEN | M0)}, /* csi22_dx0 */
+ {CSI22_DY0, (IEN | M0)}, /* csi22_dy0 */
+ {CSI22_DX1, (IEN | M0)}, /* csi22_dx1 */
+ {CSI22_DY1, (IEN | M0)}, /* csi22_dy1 */
+ {USBB1_ULPITLL_CLK, (PTD | IEN | OFF_EN | OFF_PD | OFF_IN | M4)},/* usbb1_ulpiphy_clk */
+ {USBB1_ULPITLL_STP, (OFF_EN | OFF_OUT_PTD | M4)}, /* usbb1_ulpiphy_stp */
+ {USBB1_ULPITLL_DIR, (IEN | OFF_EN | OFF_PD | OFF_IN | M4)}, /* usbb1_ulpiphy_dir */
+ {USBB1_ULPITLL_NXT, (IEN | OFF_EN | OFF_PD | OFF_IN | M4)}, /* usbb1_ulpiphy_nxt */
+ {USBB1_ULPITLL_DAT0, (IEN | OFF_EN | OFF_PD | OFF_IN | M4)}, /* usbb1_ulpiphy_dat0 */
+ {USBB1_ULPITLL_DAT1, (IEN | OFF_EN | OFF_PD | OFF_IN | M4)}, /* usbb1_ulpiphy_dat1 */
+ {USBB1_ULPITLL_DAT2, (IEN | OFF_EN | OFF_PD | OFF_IN | M4)}, /* usbb1_ulpiphy_dat2 */
+ {USBB1_ULPITLL_DAT3, (IEN | OFF_EN | OFF_PD | OFF_IN | M4)}, /* usbb1_ulpiphy_dat3 */
+ {USBB1_ULPITLL_DAT4, (IEN | OFF_EN | OFF_PD | OFF_IN | M4)}, /* usbb1_ulpiphy_dat4 */
+ {USBB1_ULPITLL_DAT5, (IEN | OFF_EN | OFF_PD | OFF_IN | M4)}, /* usbb1_ulpiphy_dat5 */
+ {USBB1_ULPITLL_DAT6, (IEN | OFF_EN | OFF_PD | OFF_IN | M4)}, /* usbb1_ulpiphy_dat6 */
+ {USBB1_ULPITLL_DAT7, (IEN | OFF_EN | OFF_PD | OFF_IN | M4)}, /* usbb1_ulpiphy_dat7 */
+ {USBB1_HSIC_DATA, (PTU | IEN | M3)}, /* gpio_96 - usbh_cpen */
+ {USBB1_HSIC_STROBE, (PTU | IEN | M3)}, /* gpio_97 - usbh_reset */
+ {ABE_MCBSP2_CLKX, (IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* abe_mcbsp2_clkx */
+ {ABE_MCBSP2_DR, (IEN | OFF_EN | OFF_OUT_PTD | M0)}, /* abe_mcbsp2_dr */
+ {ABE_MCBSP2_DX, (OFF_EN | OFF_OUT_PTD | M0)}, /* abe_mcbsp2_dx */
+ {ABE_MCBSP2_FSX, (IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* abe_mcbsp2_fsx */
+ {ABE_PDM_UL_DATA, (PTD | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* abe_pdm_ul_data */
+ {ABE_PDM_DL_DATA, (PTD | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* abe_pdm_dl_data */
+ {ABE_PDM_FRAME, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* abe_pdm_frame */
+ {ABE_PDM_LB_CLK, (PTD | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* abe_pdm_lb_clk */
+ {ABE_CLKS, (PTD | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* abe_clks */
+ {ABE_DMIC_CLK1, (M0)}, /* abe_dmic_clk1 */
+ {ABE_DMIC_DIN1, (IEN | M0)}, /* abe_dmic_din1 */
+ {ABE_DMIC_DIN2, (IEN | M0)}, /* abe_dmic_din2 */
+ {ABE_DMIC_DIN3, (IEN | M0)}, /* abe_dmic_din3 */
+ {UART2_CTS, (PTU | IEN | M0)}, /* uart2_cts */
+ {UART2_RTS, (M0)}, /* uart2_rts */
+ {UART2_RX, (PTU | IEN | M0)}, /* uart2_rx */
+ {UART2_TX, (M0)}, /* uart2_tx */
+ {HDQ_SIO, (M0)}, /* hdq-sio */
+ {MCSPI1_CLK, (IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* mcspi1_clk */
+ {MCSPI1_SOMI, (IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* mcspi1_somi */
+ {MCSPI1_SIMO, (IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* mcspi1_simo */
+ {MCSPI1_CS0, (PTD | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* mcspi1_cs0 */
+ {MCSPI1_CS1, (PTD | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* mcspi1_cs1 */
+ {SDMMC5_CLK, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* sdmmc5_clk */
+ {SDMMC5_CMD, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* sdmmc5_cmd */
+ {SDMMC5_DAT0, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* sdmmc5_dat0 */
+ {SDMMC5_DAT1, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* sdmmc5_dat1 */
+ {SDMMC5_DAT2, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* sdmmc5_dat2 */
+ {SDMMC5_DAT3, (PTU | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* sdmmc5_dat3 */
+ {MCSPI4_CLK, (IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* mcspi4_clk */
+ {MCSPI4_SIMO, (IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* mcspi4_simo */
+ {MCSPI4_SOMI, (IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* mcspi4_somi */
+ {MCSPI4_CS0, (PTD | IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* mcspi4_cs0 */
+ {UART4_RX, (IEN | PTU | M0)}, /* uart4_rx */
+ {UART4_TX, (M0)}, /* uart4_tx */
+ {USBB2_ULPITLL_CLK, (PTU | IEN | M3)}, /* gpio_157 - start_adc */
+ {USBB2_ULPITLL_STP, (PTU | IEN | M3)}, /* gpio_158 - spi_nirq */
+ {USBB2_ULPITLL_DIR, (PTU | IEN | M3)}, /* gpio_159 - bt_nreset */
+ {USBB2_ULPITLL_NXT, (PTU | IEN | M3)}, /* gpio_160 - audio_pwron*/
+ {USBB2_ULPITLL_DAT0, (PTU | IEN | M3)}, /* gpio_161 - bid_0 */
+ {USBB2_ULPITLL_DAT1, (PTU | IEN | M3)}, /* gpio_162 - bid_1 */
+ {USBB2_ULPITLL_DAT2, (PTU | IEN | M3)}, /* gpio_163 - bid_2 */
+ {USBB2_ULPITLL_DAT3, (PTU | IEN | M3)}, /* gpio_164 - bid_3 */
+ {USBB2_ULPITLL_DAT4, (PTU | IEN | M3)}, /* gpio_165 - bid_4 */
+ {USBB2_ULPITLL_DAT5, (PTU | IEN | M3)}, /* gpio_166 - ts_irq*/
+ {USBB2_ULPITLL_DAT6, (PTU | IEN | M3)}, /* gpio_167 - gps_pps */
+ {USBB2_ULPITLL_DAT7, (PTU | IEN | M3)}, /* gpio_168 */
+ {USBB2_HSIC_DATA, (PTU | IEN | M3)}, /* gpio_169 */
+ {USBB2_HSIC_STROBE, (PTU | IEN | M3)}, /* gpio_170 */
+ {UNIPRO_TX1, (PTU | IEN | M3)}, /* gpio_173 */
+ {USBA0_OTG_CE, (PTD | OFF_EN | OFF_PD | OFF_OUT_PTD | M0)}, /* usba0_otg_ce */
+ {USBA0_OTG_DP, (IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* usba0_otg_dp */
+ {USBA0_OTG_DM, (IEN | OFF_EN | OFF_PD | OFF_IN | M0)}, /* usba0_otg_dm */
+ {SYS_NIRQ1, (PTU | IEN | M0)}, /* sys_nirq1 */
+ {SYS_NIRQ2, (PTU | IEN | M0)}, /* sys_nirq2 */
+ {SYS_BOOT0, (M0)}, /* sys_boot0 */
+ {SYS_BOOT1, (M0)}, /* sys_boot1 */
+ {SYS_BOOT2, (M0)}, /* sys_boot2 */
+ {SYS_BOOT3, (M0)}, /* sys_boot3 */
+ {SYS_BOOT4, (M0)}, /* sys_boot4 */
+ {SYS_BOOT5, (M0)}, /* sys_boot5 */
+ {DPM_EMU0, (IEN | M0)}, /* dpm_emu0 */
+ {DPM_EMU1, (IEN | M0)}, /* dpm_emu1 */
+ {DPM_EMU16, (PTU | IEN | M3)}, /* gpio_27 */
+ {DPM_EMU17, (PTU | IEN | M3)}, /* gpio_28 */
+ {DPM_EMU18, (PTU | IEN | M3)}, /* gpio_29 */
+ {DPM_EMU19, (PTU | IEN | M3)}, /* gpio_30 */
+};
+
+const struct pad_conf_entry wkup_padconf_array_non_essential[] = {
+ {PAD1_FREF_XTAL_IN, (M0)}, /* fref_xtal_in */
+ {PAD0_FREF_SLICER_IN, (M0)}, /* fref_slicer_in */
+ {PAD1_FREF_CLK_IOREQ, (M0)}, /* fref_clk_ioreq */
+ {PAD0_FREF_CLK0_OUT, (M7)}, /* safe mode */
+ {PAD1_FREF_CLK3_REQ, M7}, /* safe mode */
+ {PAD0_FREF_CLK3_OUT, (M0)}, /* fref_clk3_out */
+ {PAD0_SYS_NRESPWRON, (M0)}, /* sys_nrespwron */
+ {PAD1_SYS_NRESWARM, (M0)}, /* sys_nreswarm */
+ {PAD0_SYS_PWR_REQ, (PTU | M0)}, /* sys_pwr_req */
+ {PAD1_SYS_PWRON_RESET, (M3)}, /* gpio_wk29 */
+ {PAD0_SYS_BOOT6, (M0)}, /* sys_boot6 */
+ {PAD1_SYS_BOOT7, (M0)}, /* sys_boot7 */
+};
+
+
+#endif /* _DUOVERO_MUX_DATA_H_ */
diff --git a/board/overo/overo.c b/board/overo/overo.c
index 1192d02..62b50a8 100644
--- a/board/overo/overo.c
+++ b/board/overo/overo.c
@@ -39,6 +39,11 @@ DECLARE_GLOBAL_DATA_PTR;
#define GUMSTIX_CHESTNUT43 0x06000200
#define GUMSTIX_PINTO 0x07000200
#define GUMSTIX_GALLOP43 0x08000200
+#define GUMSTIX_ALTO35 0x09000200
+#define GUMSTIX_STAGECOACH 0x0A000200
+#define GUMSTIX_THUMBO 0x0B000200
+#define GUMSTIX_TURTLECORE 0x0C000200
+#define GUMSTIX_ARBOR43C 0x0D000200
#define ETTUS_USRP_E 0x01000300
@@ -141,6 +146,7 @@ void get_board_mem_timings(struct board_sdrc_timings *timings)
timings->rfr_ctrl = SDP_3430_SDRC_RFR_CTRL_165MHz;
break;
case REVISION_1: /* Micron 256MB/512MB, 1/2 banks of 256MB */
+ case REVISION_4:
timings->mcfg = MICRON_V_MCFG_200(256 << 20);
timings->ctrla = MICRON_V_ACTIMA_200;
timings->ctrlb = MICRON_V_ACTIMB_200;
@@ -230,6 +236,8 @@ unsigned int get_expansion_id(void)
*/
int misc_init_r(void)
{
+ unsigned int expansion_id;
+
twl4030_power_init();
twl4030_led_init(TWL4030_LED_LEDEN_LEDAON | TWL4030_LED_LEDEN_LEDBON);
@@ -252,7 +260,8 @@ int misc_init_r(void)
puts("Unable to detect mmc2 connection type\n");
}
- switch (get_expansion_id()) {
+ expansion_id = get_expansion_id();
+ switch (expansion_id) {
case GUMSTIX_SUMMIT:
printf("Recognized Summit expansion board (rev %d %s)\n",
expansion_config.revision,
@@ -302,6 +311,35 @@ int misc_init_r(void)
expansion_config.fab_revision);
setenv("defaultdisplay", "lcd43");
break;
+ case GUMSTIX_ALTO35:
+ printf("Recognized Alto35 expansion board (rev %d %s)\n",
+ expansion_config.revision,
+ expansion_config.fab_revision);
+ MUX_ALTO35();
+ setenv("defaultdisplay", "lcd35");
+ break;
+ case GUMSTIX_STAGECOACH:
+ printf("Recognized Stagecoach expansion board (rev %d %s)\n",
+ expansion_config.revision,
+ expansion_config.fab_revision);
+ break;
+ case GUMSTIX_THUMBO:
+ printf("Recognized Thumbo expansion board (rev %d %s)\n",
+ expansion_config.revision,
+ expansion_config.fab_revision);
+ break;
+ case GUMSTIX_TURTLECORE:
+ printf("Recognized Turtlecore expansion board (rev %d %s)\n",
+ expansion_config.revision,
+ expansion_config.fab_revision);
+ break;
+ case GUMSTIX_ARBOR43C:
+ printf("Recognized Arbor43C expansion board (rev %d %s)\n",
+ expansion_config.revision,
+ expansion_config.fab_revision);
+ MUX_ARBOR43C();
+ setenv("defaultdisplay", "lcd43");
+ break;
case ETTUS_USRP_E:
printf("Recognized Ettus Research USRP-E (rev %d %s)\n",
expansion_config.revision,
@@ -313,7 +351,8 @@ int misc_init_r(void)
puts("No EEPROM on expansion board\n");
break;
default:
- puts("Unrecognized expansion board\n");
+ printf("Unrecognized expansion board 0x%08x\n", expansion_id);
+ break;
}
if (expansion_config.content == 1)
diff --git a/board/overo/overo.h b/board/overo/overo.h
index 64604de..57725d8 100644
--- a/board/overo/overo.h
+++ b/board/overo/overo.h
@@ -22,6 +22,7 @@ const omap3_sysinfo sysinfo = {
#define REVISION_1 0x1
#define REVISION_2 0x2
#define REVISION_3 0x3
+#define REVISION_4 0x4
/*
* IEN - Input Enable
@@ -404,4 +405,20 @@ const omap3_sysinfo sysinfo = {
MUX_VAL(CP(MCSPI1_SOMI), (IEN | PTD | DIS | M4)) /*GPIO_173 */\
MUX_VAL(CP(MCSPI1_CS1), (IDIS | PTD | EN | M4)) /*GPIO_175 */\
+#define MUX_ALTO35() \
+ MUX_VAL(CP(SYS_CLKOUT1), (IEN | PTU | EN | M4)) /*GPIO_10-BTN*/\
+ MUX_VAL(CP(UART1_TX), (IDIS | PTD | DIS | M4)) /*GPIO_148-RED LED*/\
+ MUX_VAL(CP(UART1_CTS), (IDIS | PTD | DIS | M4)) /*GPIO_150-YELLOW LED*/\
+ MUX_VAL(CP(UART1_RX), (IDIS | PTD | DIS | M4)) /*GPIO_151-BLUE LED*/\
+ MUX_VAL(CP(HDQ_SIO), (IDIS | PTD | DIS | M4)) /*GPIO_170-GREEN LED*/\
+ MUX_VAL(CP(MCSPI1_CS1), (IDIS | PTD | EN | M4)) /*GPIO_175*/\
+
+#define MUX_ARBOR43C() \
+ MUX_VAL(CP(CSI2_DX1), (IDIS | PTD | DIS | M4)) /*GPIO_114-RED LED*/\
+ MUX_VAL(CP(UART1_CTS), (IDIS | PTD | DIS | M4)) /*GPIO_150-YELLOW LED*/\
+ MUX_VAL(CP(HDQ_SIO), (IEN | PTU | EN | M4)) /*GPIO_170-BUTTON */\
+ MUX_VAL(CP(SYS_CLKOUT2), (IDIS | PTD | DIS | M4)) /*GPIO_186-BLUE LED*/\
+ MUX_VAL(CP(JTAG_EMU1), (IDIS | PTD | DIS | M4)) /*GPIO_31-CAP WAKE*/\
+ MUX_VAL(CP(SYS_CLKOUT1), (IEN | PTU | EN | M4)) /*GPIO_10-CAP IRQ*/\
+
#endif
diff --git a/board/renesas/koelsch/qos.c b/board/renesas/koelsch/qos.c
index e6c5e48..55a0420 100644
--- a/board/renesas/koelsch/qos.c
+++ b/board/renesas/koelsch/qos.c
@@ -111,6 +111,7 @@ void qos_init(void)
/* DBSC DBADJ2 */
writel(0x20042004, DBSC3_0_DBADJ2);
+ writel(0x20042004, DBSC3_1_DBADJ2);
/* S3C -QoS */
s3c = (struct rcar_s3c *)S3C_BASE;
diff --git a/board/xilinx/zynq/.gitignore b/board/xilinx/zynq/.gitignore
new file mode 100644
index 0000000..68b8edd
--- /dev/null
+++ b/board/xilinx/zynq/.gitignore
@@ -0,0 +1 @@
+ps7_init.[ch]
diff --git a/board/xilinx/zynq/Makefile b/board/xilinx/zynq/Makefile
index 3f19a1c..fd93f63 100644
--- a/board/xilinx/zynq/Makefile
+++ b/board/xilinx/zynq/Makefile
@@ -6,4 +6,7 @@
#
obj-y := board.o
-obj-$(CONFIG_SPL_BUILD) += ps7_init.o
+
+# Please copy ps7_init.c/h from hw project to this directory
+obj-$(CONFIG_SPL_BUILD) += \
+ $(if $(wildcard $(srctree)/$(src)/ps7_init.c), ps7_init.o)
diff --git a/board/xilinx/zynq/board.c b/board/xilinx/zynq/board.c
index c8cc2bc..258632e 100644
--- a/board/xilinx/zynq/board.c
+++ b/board/xilinx/zynq/board.c
@@ -6,6 +6,8 @@
#include <common.h>
#include <fdtdec.h>
+#include <fpga.h>
+#include <mmc.h>
#include <netdev.h>
#include <zynqpl.h>
#include <asm/arch/hardware.h>
@@ -13,21 +15,23 @@
DECLARE_GLOBAL_DATA_PTR;
-#ifdef CONFIG_FPGA
-xilinx_desc fpga;
+#if (defined(CONFIG_FPGA) && !defined(CONFIG_SPL_BUILD)) || \
+ (defined(CONFIG_SPL_FPGA_SUPPORT) && defined(CONFIG_SPL_BUILD))
+static xilinx_desc fpga;
/* It can be done differently */
-xilinx_desc fpga010 = XILINX_XC7Z010_DESC(0x10);
-xilinx_desc fpga015 = XILINX_XC7Z015_DESC(0x15);
-xilinx_desc fpga020 = XILINX_XC7Z020_DESC(0x20);
-xilinx_desc fpga030 = XILINX_XC7Z030_DESC(0x30);
-xilinx_desc fpga045 = XILINX_XC7Z045_DESC(0x45);
-xilinx_desc fpga100 = XILINX_XC7Z100_DESC(0x100);
+static xilinx_desc fpga010 = XILINX_XC7Z010_DESC(0x10);
+static xilinx_desc fpga015 = XILINX_XC7Z015_DESC(0x15);
+static xilinx_desc fpga020 = XILINX_XC7Z020_DESC(0x20);
+static xilinx_desc fpga030 = XILINX_XC7Z030_DESC(0x30);
+static xilinx_desc fpga045 = XILINX_XC7Z045_DESC(0x45);
+static xilinx_desc fpga100 = XILINX_XC7Z100_DESC(0x100);
#endif
int board_init(void)
{
-#ifdef CONFIG_FPGA
+#if (defined(CONFIG_FPGA) && !defined(CONFIG_SPL_BUILD)) || \
+ (defined(CONFIG_SPL_FPGA_SUPPORT) && defined(CONFIG_SPL_BUILD))
u32 idcode;
idcode = zynq_slcr_get_idcode();
@@ -54,7 +58,8 @@ int board_init(void)
}
#endif
-#ifdef CONFIG_FPGA
+#if (defined(CONFIG_FPGA) && !defined(CONFIG_SPL_BUILD)) || \
+ (defined(CONFIG_SPL_FPGA_SUPPORT) && defined(CONFIG_SPL_BUILD))
fpga_init();
fpga_add(fpga_xilinx, &fpga);
#endif
diff --git a/board/xilinx/zynq/ps7_init.c b/board/xilinx/zynq/ps7_init.c
deleted file mode 100644
index c47da09..0000000
--- a/board/xilinx/zynq/ps7_init.c
+++ /dev/null
@@ -1,12 +0,0 @@
-/*
- * (C) Copyright 2014 Xilinx, Inc. Michal Simek
- *
- * SPDX-License-Identifier: GPL-2.0+
- */
-#include <common.h>
-#include <asm/arch/spl.h>
-
-__weak void ps7_init(void)
-{
- puts("Please copy ps7_init.c/h from hw project\n");
-}
diff --git a/board/xilinx/zynq/xil_io.h b/board/xilinx/zynq/xil_io.h
new file mode 100644
index 0000000..e59a977
--- /dev/null
+++ b/board/xilinx/zynq/xil_io.h
@@ -0,0 +1,13 @@
+/*
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef XIL_IO_H /* prevent circular inclusions */
+#define XIL_IO_H
+
+/*
+ * This empty file is here because ps7_init.c exported by hw project
+ * has #include "xil_io.h" line.
+ */
+
+#endif /* XIL_IO_H */
diff --git a/boards.cfg b/boards.cfg
index 440c312..221b7f8 100644
--- a/boards.cfg
+++ b/boards.cfg
@@ -362,8 +362,10 @@ Active arm armv7 omap3 ti evm
Active arm armv7 omap3 ti evm omap3_evm_quick_nand - -
Active arm armv7 omap3 ti sdp3430 omap3_sdp3430 - Nishanth Menon <nm@ti.com>
Active arm armv7 omap3 timll devkit8000 devkit8000 - Thomas Weber <weber@corscience.de>
+Active arm armv7 omap4 gumstix duovero duovero - Ash Charles <ash@gumstix.com>
Active arm armv7 omap4 ti panda omap4_panda - Sricharan R <r.sricharan@ti.com>
Active arm armv7 omap4 ti sdp4430 omap4_sdp4430 - Sricharan R <r.sricharan@ti.com>
+Active arm armv7 omap5 compulab cm_t54 cm_t54 - Dmitry Lifshitz <lifshitz@compulab.co.il>
Active arm armv7 omap5 ti dra7xx dra7xx_evm dra7xx_evm:CONS_INDEX=1 Lokesh Vutla <lokeshvutla@ti.com>
Active arm armv7 omap5 ti dra7xx dra7xx_evm_qspiboot dra7xx_evm:CONS_INDEX=1,QSPI_BOOT Lokesh Vutla <lokeshvutla@ti.com>
Active arm armv7 omap5 ti dra7xx dra7xx_evm_uart3 dra7xx_evm:CONS_INDEX=3,SPL_YMODEM_SUPPORT Lokesh Vutla <lokeshvutla@ti.com>
diff --git a/drivers/usb/host/Makefile b/drivers/usb/host/Makefile
index b301e28..7211c6a 100644
--- a/drivers/usb/host/Makefile
+++ b/drivers/usb/host/Makefile
@@ -37,6 +37,7 @@ obj-$(CONFIG_USB_EHCI_SPEAR) += ehci-spear.o
obj-$(CONFIG_USB_EHCI_TEGRA) += ehci-tegra.o
obj-$(CONFIG_USB_EHCI_VCT) += ehci-vct.o
obj-$(CONFIG_USB_EHCI_RMOBILE) += ehci-rmobile.o
+obj-$(CONFIG_USB_EHCI_ZYNQ) += ehci-zynq.o
# xhci
obj-$(CONFIG_USB_XHCI) += xhci.o xhci-mem.o xhci-ring.o
diff --git a/drivers/usb/host/ehci-zynq.c b/drivers/usb/host/ehci-zynq.c
new file mode 100644
index 0000000..7770d05
--- /dev/null
+++ b/drivers/usb/host/ehci-zynq.c
@@ -0,0 +1,104 @@
+/*
+ * (C) Copyright 2014, Xilinx, Inc
+ *
+ * USB Low level initialization(Specific to zynq)
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#include <common.h>
+#include <asm/arch/hardware.h>
+#include <asm/arch/sys_proto.h>
+#include <asm/io.h>
+#include <usb.h>
+#include <usb/ehci-fsl.h>
+#include <usb/ulpi.h>
+
+#include "ehci.h"
+
+#define ZYNQ_USB_USBCMD_RST 0x0000002
+#define ZYNQ_USB_USBCMD_STOP 0x0000000
+#define ZYNQ_USB_NUM_MIO 12
+
+/*
+ * Create the appropriate control structures to manage
+ * a new EHCI host controller.
+ */
+int ehci_hcd_init(int index, enum usb_init_type init, struct ehci_hccr **hccr,
+ struct ehci_hcor **hcor)
+{
+ struct usb_ehci *ehci;
+ struct ulpi_viewport ulpi_vp;
+ int ret, mio_usb;
+ /* Used for writing the ULPI data address */
+ struct ulpi_regs *ulpi = (struct ulpi_regs *)0;
+
+ if (!index) {
+ mio_usb = zynq_slcr_get_mio_pin_status("usb0");
+ if (mio_usb != ZYNQ_USB_NUM_MIO) {
+ printf("usb0 wrong num MIO: %d, Index %d\n", mio_usb,
+ index);
+ return -1;
+ }
+ ehci = (struct usb_ehci *)ZYNQ_USB_BASEADDR0;
+ } else {
+ mio_usb = zynq_slcr_get_mio_pin_status("usb1");
+ if (mio_usb != ZYNQ_USB_NUM_MIO) {
+ printf("usb1 wrong num MIO: %d, Index %d\n", mio_usb,
+ index);
+ return -1;
+ }
+ ehci = (struct usb_ehci *)ZYNQ_USB_BASEADDR1;
+ }
+
+ *hccr = (struct ehci_hccr *)((uint32_t)&ehci->caplength);
+ *hcor = (struct ehci_hcor *)((uint32_t) *hccr +
+ HC_LENGTH(ehci_readl(&(*hccr)->cr_capbase)));
+
+ ulpi_vp.viewport_addr = (u32)&ehci->ulpi_viewpoint;
+ ulpi_vp.port_num = 0;
+
+ ret = ulpi_init(&ulpi_vp);
+ if (ret) {
+ puts("zynq ULPI viewport init failed\n");
+ return -1;
+ }
+
+ /* ULPI set flags */
+ ulpi_write(&ulpi_vp, &ulpi->otg_ctrl,
+ ULPI_OTG_DP_PULLDOWN | ULPI_OTG_DM_PULLDOWN |
+ ULPI_OTG_EXTVBUSIND);
+ ulpi_write(&ulpi_vp, &ulpi->function_ctrl,
+ ULPI_FC_FULL_SPEED | ULPI_FC_OPMODE_NORMAL |
+ ULPI_FC_SUSPENDM);
+ ulpi_write(&ulpi_vp, &ulpi->iface_ctrl, 0);
+
+ /* Set VBus */
+ ulpi_write(&ulpi_vp, &ulpi->otg_ctrl_set,
+ ULPI_OTG_DRVVBUS | ULPI_OTG_DRVVBUS_EXT);
+
+ return 0;
+}
+
+/*
+ * Destroy the appropriate control structures corresponding
+ * the the EHCI host controller.
+ */
+int ehci_hcd_stop(int index)
+{
+ struct usb_ehci *ehci;
+
+ if (!index)
+ ehci = (struct usb_ehci *)ZYNQ_USB_BASEADDR0;
+ else
+ ehci = (struct usb_ehci *)ZYNQ_USB_BASEADDR1;
+
+ /* Stop controller */
+ writel(ZYNQ_USB_USBCMD_STOP, &ehci->usbcmd);
+ udelay(1000);
+
+ /* Initiate controller reset */
+ writel(ZYNQ_USB_USBCMD_RST, &ehci->usbcmd);
+
+ return 0;
+}
diff --git a/include/configs/armadillo-800eva.h b/include/configs/armadillo-800eva.h
index 17a2da0..8bb932c 100644
--- a/include/configs/armadillo-800eva.h
+++ b/include/configs/armadillo-800eva.h
@@ -48,6 +48,7 @@
#define CONFIG_USE_ARCH_MEMCPY
#define CONFIG_TMU_TIMER
#define CONFIG_SYS_DCACHE_OFF
+#define CONFIG_SYS_GENERIC_BOARD
/* STACK */
#define CONFIG_SYS_INIT_SP_ADDR 0xE8083000
diff --git a/include/configs/cm_t54.h b/include/configs/cm_t54.h
new file mode 100644
index 0000000..db04095
--- /dev/null
+++ b/include/configs/cm_t54.h
@@ -0,0 +1,149 @@
+/*
+ * Config file for Compulab CM-T54 board
+ *
+ * Copyright (C) 2014, Compulab Ltd - http://compulab.co.il/
+ *
+ * Author: Dmitry Lifshitz <lifshitz@compulab.co.il>
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __CONFIG_CM_T54_H
+#define __CONFIG_CM_T54_H
+
+#define CONFIG_CM_T54
+#define CONFIG_DRAM_2G
+
+#include <configs/ti_omap5_common.h>
+
+#undef CONFIG_MISC_INIT_R
+#undef CONFIG_SPL_OS_BOOT
+
+/* Device Tree defines */
+#define CONFIG_OF_LIBFDT
+#define CONFIG_OF_BOARD_SETUP
+
+/* EEPROM related defines */
+#define CONFIG_SYS_I2C_OMAP34XX
+#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
+
+/* Enable SD/MMC CD and WP GPIOs */
+#define OMAP_HSMMC_USE_GPIO
+
+/* UART setup */
+#define CONFIG_CONS_INDEX 4
+#define CONFIG_SYS_NS16550_COM4 UART4_BASE
+#define CONFIG_BAUDRATE 115200
+
+/* SD/MMC RAW boot */
+#undef CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR
+#undef CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS
+
+#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x200 /* 0x40000 - 256 KB */
+#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x300 /* 384 KB */
+
+/* MMC ENV related defines */
+#undef CONFIG_ENV_OFFSET
+#undef CONFIG_ENV_SIZE
+
+#define CONFIG_ENV_IS_IN_MMC
+#define CONFIG_SYS_MMC_ENV_DEV 1 /* SLOT2: eMMC(1) */
+#define CONFIG_SYS_MMC_ENV_PART 0
+#define CONFIG_ENV_OFFSET 0xc0000 /* (in bytes) 768 KB */
+#define CONFIG_ENV_SIZE (16 << 10) /* 16 KB */
+#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)
+#define CONFIG_SYS_REDUNDAND_ENVIRONMENT
+#define CONFIG_CMD_SAVEENV
+
+/* Enhance our eMMC support / experience. */
+#define CONFIG_HSMMC2_8BIT
+#define CONFIG_SUPPORT_EMMC_BOOT
+
+/* USB UHH support options */
+#define CONFIG_CMD_USB
+#define CONFIG_USB_HOST
+#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_OMAP
+#define CONFIG_USB_STORAGE
+#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 3
+#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
+
+#define CONFIG_OMAP_EHCI_PHY2_RESET_GPIO 76 /* HSIC2 HUB #RESET */
+#define CONFIG_OMAP_EHCI_PHY3_RESET_GPIO 83 /* HSIC3 ETH #RESET */
+
+/* Enabled commands */
+#define CONFIG_CMD_DHCP /* DHCP Support */
+#define CONFIG_CMD_NET /* bootp, tftpboot, rarpboot */
+#define CONFIG_CMD_PING
+
+/* USB Networking options */
+#define CONFIG_USB_HOST_ETHER
+#define CONFIG_USB_ETHER_SMSC95XX
+#define CONFIG_USB_ETHER_RNDIS
+#define CONFIG_USB_ETHER_ASIX
+#define CONFIG_USB_ETHER_MCS7830
+
+/* Max time to hold reset on this board, see doc/README.omap-reset-time */
+#define CONFIG_OMAP_PLATFORM_RESET_TIME_MAX_USEC 16296
+
+/*
+ * Miscellaneous configurable options
+ */
+#undef CONFIG_SYS_AUTOLOAD
+#undef CONFIG_SYS_PROMPT
+#undef CONFIG_EXTRA_ENV_SETTINGS
+#undef CONFIG_BOOTCOMMAND
+#undef CONFIG_BOOTDELAY
+
+#define CONFIG_BOOTDELAY 3
+#define CONFIG_SYS_AUTOLOAD "no"
+#define CONFIG_SYS_PROMPT "CM-T54 # "
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ DEFAULT_LINUX_BOOT_ENV \
+ "baudrate=115200\0" \
+ "bootdelay=3\0" \
+ "autoload=no\0" \
+ "bootscr=bootscr.img\0" \
+ "fdtfile=omap5-sbc-t54.dtb\0" \
+ "kernel=zImage-cm-t54\0" \
+ "ramdisk=ramdisk-cm-t54.img\0" \
+ "console=ttyO3\0" \
+ "ramdisksize=16384\0" \
+ "mmcdev=0\0" \
+ "mmcroot=/dev/mmcblk1p2\0" \
+ "mmcargs=setenv bootargs console=${console} " \
+ "root=${mmcroot} rw rootwait\0" \
+ "ramroot=/dev/ram0\0" \
+ "ramargs=setenv bootargs console=${console} " \
+ "root=${ramroot} ramdisk_size=${ramdisksize} rw\0" \
+ "mmcloadkernel=load mmc ${mmcdev} ${loadaddr} ${kernel}\0" \
+ "mmcloadfdt=load mmc ${mmcdev} ${fdtaddr} ${fdtfile}\0" \
+ "mmcloadramdisk=load mmc ${mmcdev} ${rdaddr} ${ramdisk}\0" \
+ "mmcloadbootscript=load mmc ${mmcdev} ${loadaddr} ${bootsrc}\0" \
+ "mmcbootscript=echo Running bootscript from mmc${mmcdev}...; " \
+ "source ${loadaddr}\0" \
+ "mmcbootlinux=echo Booting from mmc${mmcdev} ...; " \
+ "bootz ${loadaddr} ${rdaddr} ${fdtaddr}\0" \
+ "mmcboot=if mmc dev ${mmcdev} && mmc rescan; then " \
+ "if run mmcloadbootscript; " \
+ "then run mmcbootscript; " \
+ "fi; " \
+ "if run mmcloadkernel; then " \
+ "if run mmcloadfdt; then " \
+ "if run mmcloadramdisk; then " \
+ "run ramargs; " \
+ "run mmcbootlinux; " \
+ "fi; " \
+ "run mmcargs; " \
+ "setenv rdaddr - ; " \
+ "run mmcbootlinux; " \
+ "fi; " \
+ "fi; " \
+ "fi;\0"
+
+#define CONFIG_BOOTCOMMAND \
+ "bootcmd=run mmcboot || setenv mmcdev 1; setenv mmcroot /dev/mmcblk0p2; run mmcboot;"
+
+#endif /* __CONFIG_CM_T54_H */
diff --git a/include/configs/duovero.h b/include/configs/duovero.h
new file mode 100644
index 0000000..e68f415
--- /dev/null
+++ b/include/configs/duovero.h
@@ -0,0 +1,62 @@
+/*
+ * (C) Copyright: 2013
+ * Gumstix, Inc - http://www.gumstix.com
+ * Maintainer: Ash Charles <ash@gumstix.com>
+ *
+ * Configuration settings for the Gumstix DuoVero board.
+ * See omap4_common.h for OMAP4 common part
+ *
+ * SPDX-License-Identifier: GPL-2.0+
+ */
+
+#ifndef __CONFIG_DUOVERO_H
+#define __CONFIG_DUOVERO_H
+
+/*
+ * High Level Configuration Options
+ */
+#define CONFIG_DUOVERO
+#define MACH_TYPE_OMAP4_DUOVERO 4097 /* Until the next sync */
+#define CONFIG_MACH_TYPE MACH_TYPE_OMAP4_DUOVERO
+
+#include <configs/ti_omap4_common.h>
+
+#undef CONFIG_SPL_OS_BOOT
+
+#undef CONFIG_SYS_EMIF_PRECALCULATED_TIMING_REGS
+#define CONFIG_SYS_AUTOMATIC_SDRAM_DETECTION
+#define CONFIG_SYS_DEFAULT_LPDDR2_TIMINGS
+
+#undef CONFIG_SYS_PROMPT
+#define CONFIG_SYS_PROMPT "duovero # "
+
+/* USB UHH support options */
+#define CONFIG_CMD_USB
+#define CONFIG_USB_HOST
+#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_OMAP
+#define CONFIG_USB_STORAGE
+#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 3
+
+#define CONFIG_OMAP_EHCI_PHY1_RESET_GPIO 1
+#define CONFIG_OMAP_EHCI_PHY2_RESET_GPIO 62
+
+#define CONFIG_SYS_ENABLE_PADS_ALL
+
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_NET
+
+#define CONFIG_SMC911X
+#define CONFIG_SMC911X_32_BIT
+#define CONFIG_SMC911X_BASE 0x2C000000
+
+/* GPIO */
+#define CONFIG_CMD_GPIO
+
+/* ENV related config options */
+#define CONFIG_ENV_IS_NOWHERE
+
+#define CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
+
+#endif /* __CONFIG_DUOVERO_H */
diff --git a/include/configs/koelsch.h b/include/configs/koelsch.h
index 1a93d17..6795f28 100644
--- a/include/configs/koelsch.h
+++ b/include/configs/koelsch.h
@@ -31,10 +31,22 @@
#define CONFIG_CMD_DHCP
#define CONFIG_CMD_NFS
#define CONFIG_CMD_BOOTZ
-
+#define CONFIG_CMD_USB
+#define CONFIG_CMD_FAT
#define CONFIG_CMD_SF
#define CONFIG_CMD_SPI
+
+#define CONFIG_FAT_WRITE
+#define CONFIG_EXT4_WRITE
+
#define CONFIG_SYS_TEXT_BASE 0xE6304000
+#define CONFIG_SYS_THUMB_BUILD
+#define CONFIG_SYS_GENERIC_BOARD
+
+/* Support File sytems */
+#define CONFIG_DOS_PARTITION
+#define CONFIG_SUPPORT_VFAT
+
#define CONFIG_CMDLINE_TAG
#define CONFIG_SETUP_MEMORY_TAGS
@@ -55,8 +67,6 @@
#define CONFIG_DISPLAY_CPUINFO
#define CONFIG_DISPLAY_BOARDINFO
#define CONFIG_BOARD_EARLY_INIT_F
-#define CONFIG_USE_ARCH_MEMSET
-#define CONFIG_USE_ARCH_MEMCPY
#define CONFIG_TMU_TIMER
/* STACK */
@@ -80,7 +90,6 @@
/* SCIF */
#define CONFIG_SCIF_CONSOLE
#define CONFIG_CONS_SCIF0
-#define SCIF0_BASE 0xe6e60000
#undef CONFIG_SYS_CONSOLE_INFO_QUIET
#undef CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE
#undef CONFIG_SYS_CONSOLE_ENV_OVERWRITE
@@ -159,4 +168,10 @@
#define CONFIG_SYS_I2C_POWERIC_ADDR 0x58 /* da9063 */
+/* USB */
+#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_RMOBILE
+#define CONFIG_USB_MAX_CONTROLLER_COUNT 3
+#define CONFIG_USB_STORAGE
+
#endif /* __KOELSCH_H */
diff --git a/include/configs/lager.h b/include/configs/lager.h
index ac31128..f39a788 100644
--- a/include/configs/lager.h
+++ b/include/configs/lager.h
@@ -32,10 +32,21 @@
#define CONFIG_CMD_DHCP
#define CONFIG_CMD_NFS
#define CONFIG_CMD_BOOTZ
-
+#define CONFIG_CMD_USB
+#define CONFIG_CMD_FAT
#define CONFIG_CMD_SF
#define CONFIG_CMD_SPI
+
+#define CONFIG_FAT_WRITE
+#define CONFIG_EXT4_WRITE
+
#define CONFIG_SYS_TEXT_BASE 0xE8080000
+#define CONFIG_SYS_THUMB_BUILD
+#define CONFIG_SYS_GENERIC_BOARD
+
+/* Support File sytems */
+#define CONFIG_DOS_PARTITION
+#define CONFIG_SUPPORT_VFAT
#define CONFIG_CMDLINE_TAG
#define CONFIG_SETUP_MEMORY_TAGS
@@ -57,8 +68,6 @@
#define CONFIG_DISPLAY_CPUINFO
#define CONFIG_DISPLAY_BOARDINFO
#define CONFIG_BOARD_EARLY_INIT_F
-#define CONFIG_USE_ARCH_MEMSET
-#define CONFIG_USE_ARCH_MEMCPY
#define CONFIG_TMU_TIMER
/* STACK */
@@ -82,7 +91,6 @@
/* SCIF */
#define CONFIG_SCIF_CONSOLE
#define CONFIG_CONS_SCIF0
-#define SCIF0_BASE 0xe6e60000
#undef CONFIG_SYS_CONSOLE_INFO_QUIET
#undef CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE
#undef CONFIG_SYS_CONSOLE_ENV_OVERWRITE
@@ -164,4 +172,10 @@
#define CONFIG_SYS_TMU_CLK_DIV 4
+/* USB */
+#define CONFIG_USB_EHCI
+#define CONFIG_USB_EHCI_RMOBILE
+#define CONFIG_USB_MAX_CONTROLLER_COUNT 4
+#define CONFIG_USB_STORAGE
+
#endif /* __LAGER_H */
diff --git a/include/configs/omap3_overo.h b/include/configs/omap3_overo.h
index 007e27f..7b97be9 100644
--- a/include/configs/omap3_overo.h
+++ b/include/configs/omap3_overo.h
@@ -7,135 +7,88 @@
#ifndef __CONFIG_H
#define __CONFIG_H
-/*
- * High Level Configuration Options
- */
-#define CONFIG_OMAP /* in a TI OMAP core */
-#define CONFIG_OMAP34XX /* which is a 34XX */
-#define CONFIG_OMAP3_OVERO /* working with overo */
-#define CONFIG_OMAP_GPIO
-#define CONFIG_OMAP_COMMON
-
-#define CONFIG_SDRC /* The chip has SDRC controller */
+#define CONFIG_NR_DRAM_BANKS 2 /* CS1 may or may not be populated */
+#define CONFIG_NAND
-#include <asm/arch/cpu.h> /* get chip and board defs */
-#include <asm/arch/omap3.h>
+#include <configs/ti_omap3_common.h>
-/*
- * Display CPU and Board information
- */
+/* Display CPU and Board information */
#define CONFIG_DISPLAY_CPUINFO
#define CONFIG_DISPLAY_BOARDINFO
-/* Clock Defines */
-#define V_OSCK 26000000 /* Clock output from T2 */
-#define V_SCLK (V_OSCK >> 1)
-
+/* call misc_init_r */
#define CONFIG_MISC_INIT_R
-#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */
-#define CONFIG_SETUP_MEMORY_TAGS
-#define CONFIG_INITRD_TAG
+/* pass the revision tag */
#define CONFIG_REVISION_TAG
-#define CONFIG_OF_LIBFDT
+/* override size of malloc() pool */
+#undef CONFIG_SYS_MALLOC_LEN
+#define CONFIG_ENV_SIZE (128 << 10) /* 128 KiB sector */
+/* Shift 128 << 15 provides 4 MiB heap to support UBI commands.
+ * Shift 128 << 10 provides 128 KiB heap for limited-memory devices. */
+#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (128 << 15))
-/*
- * Size of malloc() pool
- */
-#define CONFIG_ENV_SIZE (128 << 10) /* 128 KiB */
- /* Sector */
-#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (128 << 10))
-
-/*
- * Hardware drivers
- */
-
-/*
- * NS16550 Configuration
- */
-#define V_NS16550_CLK 48000000 /* 48MHz (APLL96/2) */
-
-#define CONFIG_SYS_NS16550
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE (-4)
-#define CONFIG_SYS_NS16550_CLK V_NS16550_CLK
+/* I2C Support */
+#define CONFIG_SYS_I2C_OMAP34XX
-/*
- * select serial console configuration
- */
-#define CONFIG_CONS_INDEX 3
-#define CONFIG_SYS_NS16550_COM3 OMAP34XX_UART3
-#define CONFIG_SERIAL3 3
+/* TWL4030 LED */
+#define CONFIG_TWL4030_LED
-/* allow to overwrite serial and ethaddr */
-#define CONFIG_ENV_OVERWRITE
-#define CONFIG_BAUDRATE 115200
-#define CONFIG_SYS_BAUDRATE_TABLE {4800, 9600, 19200, 38400, 57600, \
- 115200}
-#define CONFIG_GENERIC_MMC
-#define CONFIG_MMC
-#define CONFIG_OMAP_HSMMC
-#define CONFIG_DOS_PARTITION
+/* Initialize GPIOs by default */
+#define CONFIG_OMAP3_GPIO_2 /* GPIO32..63 is in GPIO Bank 2 */
+#define CONFIG_OMAP3_GPIO_3 /* GPIO64..95 is in GPIO Bank 3 */
+#define CONFIG_OMAP3_GPIO_4 /* GPIO96..127 is in GPIO Bank 4 */
+#define CONFIG_OMAP3_GPIO_5 /* GPIO128..159 is in GPIO Bank 5 */
+#define CONFIG_OMAP3_GPIO_6 /* GPIO160..191 is in GPIO Bank 6 */
/* commands to include */
-#include <config_cmd_default.h>
-
#define CONFIG_CMD_CACHE
-#define CONFIG_CMD_EXT2 /* EXT2 Support */
-#define CONFIG_CMD_FAT /* FAT support */
-#define CONFIG_CMD_JFFS2 /* JFFS2 Support */
-
-#define CONFIG_CMD_I2C /* I2C serial bus support */
-#define CONFIG_CMD_MMC /* MMC support */
-#define CONFIG_CMD_NAND /* NAND support */
-
-#undef CONFIG_CMD_FLASH /* flinfo, erase, protect */
#undef CONFIG_CMD_FPGA /* FPGA configuration Support */
#undef CONFIG_CMD_IMI /* iminfo */
-#undef CONFIG_CMD_IMLS /* List all found images */
#undef CONFIG_CMD_NFS /* NFS support */
-#define CONFIG_CMD_NET /* bootp, tftpboot, rarpboot */
-#define CONFIG_SYS_NO_FLASH
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_OMAP24_I2C_SPEED 100000
-#define CONFIG_SYS_OMAP24_I2C_SLAVE 1
-#define CONFIG_SYS_I2C_OMAP34XX
+#ifdef CONFIG_NAND
+#define CONFIG_CMD_UBI /* UBI-formated MTD partition support */
+#define CONFIG_CMD_UBIFS /* Read-only UBI volume operations */
-/*
- * TWL4030
- */
-#define CONFIG_TWL4030_POWER
-#define CONFIG_TWL4030_LED
+#define CONFIG_RBTREE /* required by CONFIG_CMD_UBI */
+#define CONFIG_LZO /* required by CONFIG_CMD_UBIFS */
-/*
- * Board NAND Info.
+#define CONFIG_MTD_PARTITIONS /* required for UBI partition support */
+
+/* NAND block size is 128 KiB. Synchronize these values with
+ * overo_nand_partitions in mach-omap2/board-overo.c in Linux:
+ * xloader 4 * NAND_BLOCK_SIZE = 512 KiB
+ * uboot 14 * NAND_BLOCK_SIZE = 1792 KiB
+ * uboot environtment 2 * NAND_BLOCK_SIZE = 256 KiB
+ * linux 64 * NAND_BLOCK_SIZE = 8 MiB
+ * rootfs remainder
*/
+#define MTDIDS_DEFAULT "nand0=omap2-nand.0"
+#define MTDPARTS_DEFAULT "mtdparts=omap2-nand.0:" \
+ "512k(xloader)," \
+ "1792k(u-boot)," \
+ "256k(environ)," \
+ "8m(linux)," \
+ "-(rootfs)"
+#else /* CONFIG_NAND */
+#define MTDPARTS_DEFAULT
+#endif /* CONFIG_NAND */
+
+/* Board NAND Info. */
#define CONFIG_SYS_NAND_QUIET_TEST
-#define CONFIG_NAND_OMAP_GPMC
#define CONFIG_SYS_NAND_ADDR NAND_BASE /* physical address */
/* to access nand */
-#define CONFIG_SYS_NAND_BASE NAND_BASE /* physical address */
- /* to access nand */
- /* at CS0 */
-#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND */
- /* devices */
-#define CONFIG_JFFS2_NAND
-/* nand device jffs2 lives on */
-#define CONFIG_JFFS2_DEV "nand0"
-/* start of jffs2 partition */
-#define CONFIG_JFFS2_PART_OFFSET 0x680000
-#define CONFIG_JFFS2_PART_SIZE 0xf980000 /* size of jffs2 */
- /* partition */
-
/* Environment information */
-#define CONFIG_BOOTDELAY 5
-
#define CONFIG_EXTRA_ENV_SETTINGS \
- "loadaddr=0x82000000\0" \
+ DEFAULT_LINUX_BOOT_ENV \
+ "fdtfile=overo.dtb\0" \
+ "bootdir=/boot\0" \
+ "bootfile=zImage\0" \
+ "usbtty=cdc_acm\0" \
"console=ttyO2,115200n8\0" \
- "mpurate=500\0" \
+ "mpurate=auto\0" \
"optargs=\0" \
"vram=12M\0" \
"dvimode=1024x768MR-16@60\0" \
@@ -145,6 +98,7 @@
"mmcrootfstype=ext3 rootwait\0" \
"nandroot=ubi0:rootfs ubi.mtd=4\0" \
"nandrootfstype=ubifs\0" \
+ "mtdparts=" MTDPARTS_DEFAULT "\0" \
"mmcargs=setenv bootargs console=${console} " \
"${optargs} " \
"mpurate=${mpurate} " \
@@ -161,80 +115,69 @@
"omapdss.def_disp=${defaultdisplay} " \
"root=${nandroot} " \
"rootfstype=${nandrootfstype}\0" \
- "loadbootscript=fatload mmc ${mmcdev} ${loadaddr} boot.scr\0" \
- "bootscript=echo Running bootscript from mmc ...; " \
+ "loadbootscript=load mmc ${mmcdev} ${loadaddr} boot.scr\0" \
+ "bootscript=echo Running boot script from mmc ...; " \
"source ${loadaddr}\0" \
- "loaduimage=fatload mmc ${mmcdev} ${loadaddr} uImage\0" \
- "mmcboot=echo Booting from mmc ...; " \
+ "loadbootenv=load mmc ${mmcdev} ${loadaddr} uEnv.txt\0" \
+ "importbootenv=echo Importing environment from mmc ...; " \
+ "env import -t ${loadaddr} ${filesize}\0" \
+ "loaduimage=load mmc ${mmcdev} ${loadaddr} uImage\0" \
+ "mmcboot=echo Booting from mmc...; " \
"run mmcargs; " \
"bootm ${loadaddr}\0" \
+ "loadzimage=load mmc ${mmcdev}:2 ${loadaddr} ${bootdir}/${bootfile}\0" \
+ "loadfdt=load mmc ${mmcdev}:2 ${fdtaddr} ${bootdir}/${fdtfile}\0" \
+ "mmcbootfdt=echo Booting with DT from mmc ...; " \
+ "run mmcargs; " \
+ "bootz ${loadaddr} - ${fdtaddr}\0" \
"nandboot=echo Booting from nand ...; " \
"run nandargs; " \
- "nand read ${loadaddr} 280000 400000; " \
+ "nand read ${loadaddr} linux; " \
"bootm ${loadaddr}\0" \
#define CONFIG_BOOTCOMMAND \
"mmc dev ${mmcdev}; if mmc rescan; then " \
"if run loadbootscript; then " \
"run bootscript; " \
- "else " \
- "if run loaduimage; then " \
- "run mmcboot; " \
- "else run nandboot; " \
- "fi; " \
- "fi; " \
- "else run nandboot; fi"
+ "fi;" \
+ "if run loadbootenv; then " \
+ "echo Loaded environment from ${bootenv};" \
+ "run importbootenv;" \
+ "fi;" \
+ "if test -n $uenvcmd; then " \
+ "echo Running uenvcmd ...;" \
+ "run uenvcmd;" \
+ "fi;" \
+ "if run loaduimage; then " \
+ "run mmcboot;" \
+ "fi;" \
+ "if run loadzimage; then " \
+ "if test -n $fdtfile; then " \
+ "if run loadfdt; then " \
+ "run mmcbootfdt;" \
+ "fi;" \
+ "fi;" \
+ "fi;" \
+ "fi;" \
+ "run nandboot; " \
-#define CONFIG_AUTO_COMPLETE 1
/*
* Miscellaneous configurable options
*/
-#define CONFIG_SYS_LONGHELP /* undef to save memory */
-#define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */
+#undef CONFIG_SYS_PROMPT
#define CONFIG_SYS_PROMPT "Overo # "
-#define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */
-/* Print Buffer Size */
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
- sizeof(CONFIG_SYS_PROMPT) + 16)
-#define CONFIG_SYS_MAXARGS 16 /* max number of command */
- /* args */
-/* Boot Argument Buffer Size */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
+
/* memtest works on */
#define CONFIG_SYS_MEMTEST_START (OMAP34XX_SDRC_CS0)
#define CONFIG_SYS_MEMTEST_END (OMAP34XX_SDRC_CS0 + \
0x01F00000) /* 31MB */
-#define CONFIG_SYS_LOAD_ADDR (OMAP34XX_SDRC_CS0) /* default load */
- /* address */
-/*
- * OMAP3 has 12 GP timers, they can be driven by the system clock
- * (12/13/16.8/19.2/38.4MHz) or by 32KHz clock. We use 13MHz (V_SCLK).
- * This rate is divided by a local divisor.
- */
-#define CONFIG_SYS_TIMERBASE OMAP34XX_GPT2
-#define CONFIG_SYS_PTV 2 /* Divisor: 2^(PTV+1) => 8 */
-
-/*-----------------------------------------------------------------------
- * Physical Memory Map
- */
-#define CONFIG_NR_DRAM_BANKS 2 /* CS1 may or may not be populated */
-#define PHYS_SDRAM_1 OMAP34XX_SDRC_CS0
-#define PHYS_SDRAM_2 OMAP34XX_SDRC_CS1
-
-/*-----------------------------------------------------------------------
- * FLASH and environment organization
- */
-
-/* **** PISMO SUPPORT *** */
-
+/* FLASH and environment organization */
/* Configure the PISMO */
#define PISMO1_NAND_SIZE GPMC_SIZE_128M
#define PISMO1_ONEN_SIZE GPMC_SIZE_128M
-#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 2 sectors */
-
-#if defined(CONFIG_CMD_NAND)
+#if defined(CONFIG_NAND)
#define CONFIG_SYS_FLASH_BASE PISMO1_NAND_BASE
#endif
@@ -250,67 +193,18 @@
#define CONFIG_ENV_OFFSET SMNAND_ENV_OFFSET
#define CONFIG_ENV_ADDR SMNAND_ENV_OFFSET
+/* Configure SMSC9211 ethernet */
#if defined(CONFIG_CMD_NET)
-/*----------------------------------------------------------------------------
- * SMSC9211 Ethernet from SMSC9118 family
- *----------------------------------------------------------------------------
- */
-
#define CONFIG_SMC911X
#define CONFIG_SMC911X_32_BIT
#define CONFIG_SMC911X_BASE 0x2C000000
-
#endif /* (CONFIG_CMD_NET) */
-/*
- * Leave it at 0x80008000 to allow booting new u-boot.bin with X-loader
- * and older u-boot.bin with the new U-Boot SPL.
- */
-#define CONFIG_SYS_TEXT_BASE 0x80008000
-#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
+/* Initial RAM setup */
#define CONFIG_SYS_INIT_RAM_ADDR 0x4020f800
#define CONFIG_SYS_INIT_RAM_SIZE 0x800
-#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + \
- CONFIG_SYS_INIT_RAM_SIZE - \
- GENERATED_GBL_DATA_SIZE)
-
#define CONFIG_SYS_CACHELINE_SIZE 64
-/* Defines for SPL */
-#define CONFIG_SPL
-#define CONFIG_SPL_FRAMEWORK
-#define CONFIG_SPL_NAND_SIMPLE
-#define CONFIG_SPL_TEXT_BASE 0x40200800
-#define CONFIG_SPL_MAX_SIZE (54 * 1024) /* 8 KB for stack */
-#define CONFIG_SPL_STACK LOW_LEVEL_SRAM_STACK
-
-/* move malloc and bss high to prevent clashing with the main image */
-#define CONFIG_SYS_SPL_MALLOC_START 0x87000000
-#define CONFIG_SYS_SPL_MALLOC_SIZE 0x80000
-#define CONFIG_SPL_BSS_START_ADDR 0x87080000 /* end of minimum RAM */
-#define CONFIG_SPL_BSS_MAX_SIZE 0x80000 /* 512 KB */
-
-#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x300 /* address 0x60000 */
-#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x200 /* 256 KB */
-#define CONFIG_SYS_MMC_SD_FAT_BOOT_PARTITION 1
-#define CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME "u-boot.img"
-
-#define CONFIG_SPL_BOARD_INIT
-#define CONFIG_SPL_LIBCOMMON_SUPPORT
-#define CONFIG_SPL_LIBDISK_SUPPORT
-#define CONFIG_SPL_I2C_SUPPORT
-#define CONFIG_SPL_LIBGENERIC_SUPPORT
-#define CONFIG_SPL_MMC_SUPPORT
-#define CONFIG_SPL_FAT_SUPPORT
-#define CONFIG_SPL_SERIAL_SUPPORT
-#define CONFIG_SPL_NAND_SUPPORT
-#define CONFIG_SPL_NAND_BASE
-#define CONFIG_SPL_NAND_DRIVERS
-#define CONFIG_SPL_NAND_ECC
-#define CONFIG_SPL_GPIO_SUPPORT
-#define CONFIG_SPL_POWER_SUPPORT
-#define CONFIG_SPL_LDSCRIPT "$(CPUDIR)/omap-common/u-boot-spl.lds"
-
/* NAND boot config */
#define CONFIG_SYS_NAND_5_ADDR_CYCLE
#define CONFIG_SYS_NAND_PAGE_COUNT 64
diff --git a/include/configs/siemens-am33x-common.h b/include/configs/siemens-am33x-common.h
index 73a123d..53816a6 100644
--- a/include/configs/siemens-am33x-common.h
+++ b/include/configs/siemens-am33x-common.h
@@ -46,6 +46,8 @@
#define CONFIG_CMD_ECHO
#define CONFIG_CMD_CACHE
+#define CONFIG_SYS_GENERIC_BOARD
+
#define CONFIG_ENV_VARS_UBOOT_CONFIG
#ifndef CONFIG_SPL_BUILD
#define CONFIG_ROOTPATH "/opt/eldk"
diff --git a/include/configs/ti_omap4_common.h b/include/configs/ti_omap4_common.h
index 77fbfb6..44b3718 100644
--- a/include/configs/ti_omap4_common.h
+++ b/include/configs/ti_omap4_common.h
@@ -109,9 +109,13 @@
"importbootenv=echo Importing environment from mmc${mmcdev} ...; " \
"env import -t ${loadaddr} ${filesize}\0" \
"loadimage=load mmc ${bootpart} ${loadaddr} ${bootdir}/${bootfile}\0" \
+ "loaduimage=load mmc ${mmcdev} ${loadaddr} uImage\0" \
"mmcboot=echo Booting from mmc${mmcdev} ...; " \
"run mmcargs; " \
"bootz ${loadaddr} - ${fdtaddr}\0" \
+ "uimageboot=echo Booting from mmc${mmcdev} ...; " \
+ "run mmcargs; " \
+ "bootm ${loadaddr}\0" \
"findfdt="\
"if test $board_name = sdp4430; then " \
"setenv fdtfile omap4-sdp.dtb; fi; " \
@@ -121,6 +125,8 @@
"setenv fdtfile omap4-panda-a4.dtb; fi;" \
"if test $board_name = panda-es; then " \
"setenv fdtfile omap4-panda-es.dtb; fi;" \
+ "if test $board_name = duovero; then " \
+ "setenv fdtfile omap4-duovero.dtb; fi;" \
"if test $fdtfile = undefined; then " \
"echo WARNING: Could not determine device tree to use; fi; \0" \
"loadfdt=load mmc ${bootpart} ${fdtaddr} ${bootdir}/${fdtfile}\0" \
@@ -144,6 +150,9 @@
"run loadfdt;" \
"run mmcboot; " \
"fi; " \
+ "if run loaduimage; then " \
+ "run uimageboot;" \
+ "fi; " \
"fi"
/*
diff --git a/include/configs/zynq-common.h b/include/configs/zynq-common.h
index 9763245..dc5bc22 100644
--- a/include/configs/zynq-common.h
+++ b/include/configs/zynq-common.h
@@ -83,10 +83,27 @@
# define CONFIG_SDHCI
# define CONFIG_ZYNQ_SDHCI
# define CONFIG_CMD_MMC
-# define CONFIG_CMD_FAT
+#endif
+
+#ifdef CONFIG_ZYNQ_USB
+# define CONFIG_USB_EHCI
+# define CONFIG_CMD_USB
+# define CONFIG_USB_STORAGE
+# define CONFIG_USB_EHCI_ZYNQ
+# define CONFIG_USB_ULPI_VIEWPORT
+# define CONFIG_USB_ULPI
+# define CONFIG_EHCI_IS_TDI
+# define CONFIG_USB_MAX_CONTROLLER_COUNT 2
+#endif
+
+#if defined(CONFIG_ZYNQ_SDHCI) || defined(CONFIG_ZYNQ_USB)
# define CONFIG_SUPPORT_VFAT
+# define CONFIG_CMD_FAT
# define CONFIG_CMD_EXT2
+# define CONFIG_FAT_WRITE
# define CONFIG_DOS_PARTITION
+# define CONFIG_CMD_EXT4
+# define CONFIG_CMD_EXT4_WRITE
#endif
#define CONFIG_SYS_I2C_ZYNQ
@@ -150,7 +167,13 @@
"bootm ${load_addr}\0" \
"jtagboot=echo TFTPing FIT to RAM... && " \
"tftpboot ${load_addr} ${fit_image} && " \
- "bootm ${load_addr}\0"
+ "bootm ${load_addr}\0" \
+ "usbboot=if usb start; then " \
+ "echo Copying FIT from USB to RAM... && " \
+ "fatload usb 0 ${load_addr} ${fit_image} && " \
+ "bootm ${load_addr}\0" \
+ "fi\0"
+
#define CONFIG_BOOTCOMMAND "run $modeboot"
#define CONFIG_BOOTDELAY 3 /* -1 to Disable autoboot */
#define CONFIG_SYS_LOAD_ADDR 0 /* default? */
@@ -165,7 +188,7 @@
#define CONFIG_SYS_LONGHELP
#define CONFIG_CLOCKS
#define CONFIG_CMD_CLK
-#define CONFIG_SYS_MAXARGS 15 /* max number of command args */
+#define CONFIG_SYS_MAXARGS 32 /* max number of command args */
#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
sizeof(CONFIG_SYS_PROMPT) + 16)
@@ -213,7 +236,7 @@
#define CONFIG_RSA
/* Extend size of kernel image for uncompression */
-#define CONFIG_SYS_BOOTM_LEN (20 * 1024 * 1024)
+#define CONFIG_SYS_BOOTM_LEN (60 * 1024 * 1024)
/* Boot FreeBSD/vxWorks from an ELF image */
#if defined(CONFIG_ZYNQ_BOOT_FREEBSD)
@@ -239,16 +262,10 @@
#define CONFIG_SPL_LIBCOMMON_SUPPORT
#define CONFIG_SPL_LIBGENERIC_SUPPORT
#define CONFIG_SPL_SERIAL_SUPPORT
+#define CONFIG_SPL_BOARD_INIT
#define CONFIG_SPL_LDSCRIPT "arch/arm/cpu/armv7/zynq/u-boot-spl.lds"
-/* Disable dcache for SPL just for sure */
-#ifdef CONFIG_SPL_BUILD
-#define CONFIG_SYS_DCACHE_OFF
-#undef CONFIG_FPGA
-#undef CONFIG_OF_CONTROL
-#endif
-
/* MMC support */
#ifdef CONFIG_ZYNQ_SDHCI0
#define CONFIG_SPL_MMC_SUPPORT
@@ -257,7 +274,18 @@
#define CONFIG_SYS_MMC_SD_FAT_BOOT_PARTITION 1
#define CONFIG_SPL_LIBDISK_SUPPORT
#define CONFIG_SPL_FAT_SUPPORT
-#define CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME "u-boot.img"
+#if defined(CONFIG_OF_CONTROL) && defined(CONFIG_OF_SEPARATE)
+# define CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME "u-boot-dtb.img"
+#else
+# define CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME "u-boot.img"
+#endif
+#endif
+
+/* Disable dcache for SPL just for sure */
+#ifdef CONFIG_SPL_BUILD
+#define CONFIG_SYS_DCACHE_OFF
+#undef CONFIG_FPGA
+#undef CONFIG_OF_CONTROL
#endif
/* Address in RAM where the parameters must be copied by SPL. */
diff --git a/include/configs/zynq_zc70x.h b/include/configs/zynq_zc70x.h
index de0e241..291a5fe 100644
--- a/include/configs/zynq_zc70x.h
+++ b/include/configs/zynq_zc70x.h
@@ -19,6 +19,7 @@
#define CONFIG_SYS_NO_FLASH
#define CONFIG_ZYNQ_SDHCI0
+#define CONFIG_ZYNQ_USB
#define CONFIG_ZYNQ_I2C0
#define CONFIG_ZYNQ_EEPROM
#define CONFIG_ZYNQ_BOOT_FREEBSD
diff --git a/include/configs/zynq_zed.h b/include/configs/zynq_zed.h
index 274140c..ce17d40 100644
--- a/include/configs/zynq_zed.h
+++ b/include/configs/zynq_zed.h
@@ -18,6 +18,7 @@
#define CONFIG_SYS_NO_FLASH
+#define CONFIG_ZYNQ_USB
#define CONFIG_ZYNQ_SDHCI0
#define CONFIG_ZYNQ_BOOT_FREEBSD
#define CONFIG_DEFAULT_DEVICE_TREE zynq-zed