summaryrefslogtreecommitdiff
diff options
context:
space:
mode:
-rw-r--r--README7
-rw-r--r--cpu/mpc5xxx/i2c.c49
-rw-r--r--include/configs/galaxy5200.h1
3 files changed, 57 insertions, 0 deletions
diff --git a/README b/README
index c90f6ee..ff4ed8b 100644
--- a/README
+++ b/README
@@ -1366,6 +1366,13 @@ The following options need to be configured:
therefore be cleared to 0 (See, eg, MPC823e User's Manual
p.16-473). So, set CONFIG_SYS_I2C_SLAVE to 0.
+ CONFIG_SYS_I2C_INIT_MPC5XXX
+
+ When a board is reset during an i2c bus transfer
+ chips might think that the current transfer is still
+ in progress. Reset the slave devices by sending start
+ commands until the slave device responds.
+
That's all that's required for CONFIG_HARD_I2C.
If you use the software i2c interface (CONFIG_SOFT_I2C)
diff --git a/cpu/mpc5xxx/i2c.c b/cpu/mpc5xxx/i2c.c
index 2341932..4f7f716 100644
--- a/cpu/mpc5xxx/i2c.c
+++ b/cpu/mpc5xxx/i2c.c
@@ -207,6 +207,52 @@ static int receive_bytes(uchar chip, char *buf, int len)
return 0;
}
+#if defined(CONFIG_SYS_I2C_INIT_MPC5XXX)
+
+#define FDR510(x) (u8) (((x & 0x20) >> 3) | (x & 0x3))
+#define FDR432(x) (u8) ((x & 0x1C) >> 2)
+/*
+ * Reset any i2c devices that may have been interrupted during a system reset.
+ * Normally this would be accomplished by clocking the line until SCL and SDA
+ * are released and then sending a start condtiion (From an Atmel datasheet).
+ * There is no direct access to the i2c pins so instead create start commands
+ * through the i2c interface. Send a start command then delay for the SDA Hold
+ * time, repeat this by disabling/enabling the bus a total of 9 times.
+ */
+static void send_reset(void)
+{
+ struct mpc5xxx_i2c *regs = (struct mpc5xxx_i2c *)I2C_BASE;
+ int i;
+ u32 delay;
+ u8 fdr;
+ int SDA_Tap[] = { 3, 3, 4, 4, 1, 1, 2, 2};
+ struct mpc5xxx_i2c_tap scltap[] = {
+ {4, 1},
+ {4, 2},
+ {6, 4},
+ {6, 8},
+ {14, 16},
+ {30, 32},
+ {62, 64},
+ {126, 128}
+ };
+
+ fdr = (u8)mpc_reg_in(&regs->mfdr);
+
+ delay = scltap[FDR432(fdr)].scl2tap + ((SDA_Tap[FDR510(fdr)] - 1) * \
+ scltap[FDR432(fdr)].tap2tap) + 3;
+
+ for (i = 0; i < 9; i++) {
+ mpc_reg_out(&regs->mcr, I2C_EN|I2C_STA|I2C_TX, I2C_INIT_MASK);
+ udelay(delay);
+ mpc_reg_out(&regs->mcr, 0, I2C_INIT_MASK);
+ udelay(delay);
+ }
+
+ mpc_reg_out(&regs->mcr, I2C_EN, I2C_INIT_MASK);
+}
+#endif /* CONFIG_SYS_I2c_INIT_MPC5XXX */
+
/**************** I2C API ****************/
void i2c_init(int speed, int saddr)
@@ -225,6 +271,9 @@ void i2c_init(int speed, int saddr)
mpc_reg_out(&regs->mcr, I2C_EN, I2C_INIT_MASK);
mpc_reg_out(&regs->msr, 0, I2C_IF);
+#if defined(CONFIG_SYS_I2C_INIT_MPC5XXX)
+ send_reset();
+#endif
return;
}
diff --git a/include/configs/galaxy5200.h b/include/configs/galaxy5200.h
index a5b5a03..f4b520d 100644
--- a/include/configs/galaxy5200.h
+++ b/include/configs/galaxy5200.h
@@ -110,6 +110,7 @@
#define CONFIG_SYS_I2C_MODULE 2 /* Select I2C module #1 or #2 */
#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */
#define CONFIG_SYS_I2C_SLAVE 0x7F
+#define CONFIG_SYS_I2C_INIT_MPC5XXX /* Reset devices on i2c bus */
/*
* EEPROM CAT24WC32 configuration