diff options
33 files changed, 459 insertions, 250 deletions
diff --git a/arch/arm/cpu/arm926ejs/mxs/mxs.c b/arch/arm/cpu/arm926ejs/mxs/mxs.c index a6af0fc..2298620 100644 --- a/arch/arm/cpu/arm926ejs/mxs/mxs.c +++ b/arch/arm/cpu/arm926ejs/mxs/mxs.c @@ -167,9 +167,9 @@ const char *get_imx_type(u32 imxtype) { switch (imxtype) { case MXC_CPU_MX23: - return "23"; /* Quad-Plus version of the mx6 */ + return "23"; case MXC_CPU_MX28: - return "28"; /* Dual-Plus version of the mx6 */ + return "28"; default: return "??"; } diff --git a/arch/arm/cpu/armv7/mx6/clock.c b/arch/arm/cpu/armv7/mx6/clock.c index e6f2275..ff932aa 100644 --- a/arch/arm/cpu/armv7/mx6/clock.c +++ b/arch/arm/cpu/armv7/mx6/clock.c @@ -97,7 +97,7 @@ void enable_enet_clk(unsigned char enable) { u32 mask, *addr; - if (is_cpu_type(MXC_CPU_MX6UL)) { + if (is_mx6ul()) { mask = MXC_CCM_CCGR3_ENET_MASK; addr = &imx_ccm->CCGR3; } else { @@ -117,7 +117,7 @@ void enable_uart_clk(unsigned char enable) { u32 mask; - if (is_cpu_type(MXC_CPU_MX6UL)) + if (is_mx6ul()) mask = MXC_CCM_CCGR5_UART_MASK; else mask = MXC_CCM_CCGR5_UART_MASK | MXC_CCM_CCGR5_UART_SERIAL_MASK; @@ -168,7 +168,7 @@ int enable_i2c_clk(unsigned char enable, unsigned i2c_num) reg &= ~mask; __raw_writel(reg, &imx_ccm->CCGR2); } else { - if (is_cpu_type(MXC_CPU_MX6SX) || is_cpu_type(MXC_CPU_MX6UL)) { + if (is_mx6sx() || is_mx6ul()) { mask = MXC_CCM_CCGR6_I2C4_MASK; addr = &imx_ccm->CCGR6; } else { @@ -279,7 +279,7 @@ static u32 mxc_get_pll_pfd(enum pll_clocks pll, int pfd_num) switch (pll) { case PLL_BUS: - if (!is_cpu_type(MXC_CPU_MX6UL)) { + if (!is_mx6ul()) { if (pfd_num == 3) { /* No PFD3 on PPL2 */ return 0; @@ -379,8 +379,8 @@ static u32 get_ipg_per_clk(void) u32 reg, perclk_podf; reg = __raw_readl(&imx_ccm->cscmr1); - if (is_cpu_type(MXC_CPU_MX6SL) || is_cpu_type(MXC_CPU_MX6SX) || - is_mx6dqp() || is_cpu_type(MXC_CPU_MX6UL)) { + if (is_mx6sl() || is_mx6sx() || + is_mx6dqp() || is_mx6ul()) { if (reg & MXC_CCM_CSCMR1_PER_CLK_SEL_MASK) return MXC_HCLK; /* OSC 24Mhz */ } @@ -396,8 +396,7 @@ static u32 get_uart_clk(void) u32 freq = decode_pll(PLL_USBOTG, MXC_HCLK) / 6; /* static divider */ reg = __raw_readl(&imx_ccm->cscdr1); - if (is_cpu_type(MXC_CPU_MX6SL) || is_cpu_type(MXC_CPU_MX6SX) || - is_mx6dqp() || is_cpu_type(MXC_CPU_MX6UL)) { + if (is_mx6sl() || is_mx6sx() || is_mx6dqp() || is_mx6ul()) { if (reg & MXC_CCM_CSCDR1_UART_CLK_SEL) freq = MXC_HCLK; } @@ -416,8 +415,7 @@ static u32 get_cspi_clk(void) cspi_podf = (reg & MXC_CCM_CSCDR2_ECSPI_CLK_PODF_MASK) >> MXC_CCM_CSCDR2_ECSPI_CLK_PODF_OFFSET; - if (is_mx6dqp() || is_cpu_type(MXC_CPU_MX6SL) || - is_cpu_type(MXC_CPU_MX6SX) || is_cpu_type(MXC_CPU_MX6UL)) { + if (is_mx6dqp() || is_mx6sl() || is_mx6sx() || is_mx6ul()) { if (reg & MXC_CCM_CSCDR2_ECSPI_CLK_SEL_MASK) return MXC_HCLK / (cspi_podf + 1); } @@ -479,14 +477,13 @@ static u32 get_mmdc_ch0_clk(void) u32 freq, podf, per2_clk2_podf, pmu_misc2_audio_div; - if (is_cpu_type(MXC_CPU_MX6SX) || is_cpu_type(MXC_CPU_MX6UL) || - is_cpu_type(MXC_CPU_MX6SL)) { + if (is_mx6sx() || is_mx6ul() || is_mx6sl()) { podf = (cbcdr & MXC_CCM_CBCDR_MMDC_CH1_PODF_MASK) >> MXC_CCM_CBCDR_MMDC_CH1_PODF_OFFSET; if (cbcdr & MXC_CCM_CBCDR_PERIPH2_CLK_SEL) { per2_clk2_podf = (cbcdr & MXC_CCM_CBCDR_PERIPH2_CLK2_PODF_MASK) >> MXC_CCM_CBCDR_PERIPH2_CLK2_PODF_OFFSET; - if (is_cpu_type(MXC_CPU_MX6SL)) { + if (is_mx6sl()) { if (cbcmr & MXC_CCM_CBCMR_PERIPH2_CLK2_SEL) freq = MXC_HCLK; else @@ -618,7 +615,7 @@ void mxs_set_lcdclk(u32 base_addr, u32 freq) debug("mxs_set_lcdclk, freq = %dKHz\n", freq); - if ((!is_cpu_type(MXC_CPU_MX6SX)) && !is_cpu_type(MXC_CPU_MX6UL)) { + if (!is_mx6sx() && !is_mx6ul()) { debug("This chip not support lcd!\n"); return; } @@ -630,7 +627,7 @@ void mxs_set_lcdclk(u32 base_addr, u32 freq) return; } - if (is_cpu_type(MXC_CPU_MX6SX)) { + if (is_mx6sx()) { reg = readl(&imx_ccm->cscdr2); /* Can't change clocks when clock not from pre-mux */ if ((reg & MXC_CCM_CSCDR2_LCDIF2_CLK_SEL_MASK) != 0) @@ -711,7 +708,7 @@ void mxs_set_lcdclk(u32 base_addr, u32 freq) MXC_CCM_CBCMR_LCDIF1_PODF_MASK, ((postd - 1) << MXC_CCM_CBCMR_LCDIF1_PODF_OFFSET)); - } else if (is_cpu_type(MXC_CPU_MX6SX)) { + } else if (is_mx6sx()) { /* Setting LCDIF2 for i.MX6SX */ if (enable_pll_video(pll_div, pll_num, pll_denom, post_div)) return; @@ -737,7 +734,7 @@ int enable_lcdif_clock(u32 base_addr) u32 reg = 0; u32 lcdif_clk_sel_mask, lcdif_ccgr3_mask; - if (is_cpu_type(MXC_CPU_MX6SX)) { + if (is_mx6sx()) { if ((base_addr != LCDIF1_BASE_ADDR) && (base_addr != LCDIF2_BASE_ADDR)) { puts("Wrong LCD interface!\n"); @@ -752,7 +749,7 @@ int enable_lcdif_clock(u32 base_addr) MXC_CCM_CCGR3_DISP_AXI_MASK) : (MXC_CCM_CCGR3_LCDIF1_PIX_MASK | MXC_CCM_CCGR3_DISP_AXI_MASK); - } else if (is_cpu_type(MXC_CPU_MX6UL)) { + } else if (is_mx6ul()) { if (base_addr != LCDIF1_BASE_ADDR) { puts("Wrong LCD interface!\n"); return -EINVAL; @@ -850,8 +847,7 @@ int enable_fec_anatop_clock(int fec_id, enum enet_freq freq) reg |= BF_ANADIG_PLL_ENET_DIV_SELECT(freq); } else if (fec_id == 1) { /* Only i.MX6SX/UL support ENET2 */ - if (!(is_cpu_type(MXC_CPU_MX6SX) || - is_cpu_type(MXC_CPU_MX6UL))) + if (!(is_mx6sx() || is_mx6ul())) return -EINVAL; reg &= ~BM_ANADIG_PLL_ENET2_DIV_SELECT; reg |= BF_ANADIG_PLL_ENET2_DIV_SELECT(freq); @@ -1044,7 +1040,7 @@ int enable_pcie_clock(void) #define ANADIG_ANA_MISC1_LVDS1_CLK_SEL_PCIE_REF 0xa #define ANADIG_ANA_MISC1_LVDS1_CLK_SEL_SATA_REF 0xb - if (is_cpu_type(MXC_CPU_MX6SX)) + if (is_mx6sx()) lvds1_clk_sel = ANADIG_ANA_MISC1_LVDS1_CLK_SEL_PCIE_REF; else lvds1_clk_sel = ANADIG_ANA_MISC1_LVDS1_CLK_SEL_SATA_REF; @@ -1228,7 +1224,7 @@ static void disable_ldb_di_clock_sources(void) /* Make sure PFDs are disabled at boot. */ reg = readl(&mxc_ccm->analog_pfd_528); /* Cannot disable pll2_pfd2_396M, as it is the MMDC clock in iMX6DL */ - if (is_cpu_type(MXC_CPU_MX6DL)) + if (is_mx6sdl()) reg |= 0x80008080; else reg |= 0x80808080; @@ -1251,7 +1247,7 @@ static void enable_ldb_di_clock_sources(void) int reg; reg = readl(&mxc_ccm->analog_pfd_528); - if (is_cpu_type(MXC_CPU_MX6DL)) + if (is_mx6sdl()) reg &= ~(0x80008080); else reg &= ~(0x80808080); diff --git a/arch/arm/cpu/armv7/mx6/ddr.c b/arch/arm/cpu/armv7/mx6/ddr.c index 1e7ae28..f151eec 100644 --- a/arch/arm/cpu/armv7/mx6/ddr.c +++ b/arch/arm/cpu/armv7/mx6/ddr.c @@ -888,8 +888,7 @@ void mx6sdl_dram_iocfg(unsigned width, #define MR(val, ba, cmd, cs1) \ ((val << 16) | (1 << 15) | (cmd << 4) | (cs1 << 3) | ba) #define MMDC1(entry, value) do { \ - if (!is_cpu_type(MXC_CPU_MX6SX) && !is_cpu_type(MXC_CPU_MX6UL) && \ - !is_cpu_type(MXC_CPU_MX6SL)) \ + if (!is_mx6sx() && !is_mx6ul() && !is_mx6sl()) \ mmdc1->entry = value; \ } while (0) @@ -1197,12 +1196,11 @@ void mx6_ddr3_cfg(const struct mx6_ddr_sysinfo *sysinfo, u16 mem_speed = ddr3_cfg->mem_speed; mmdc0 = (struct mmdc_p_regs *)MMDC_P0_BASE_ADDR; - if (!is_cpu_type(MXC_CPU_MX6SX) && !is_cpu_type(MXC_CPU_MX6UL) && - !is_cpu_type(MXC_CPU_MX6SL)) + if (!is_mx6sx() && !is_mx6ul() && !is_mx6sl()) mmdc1 = (struct mmdc_p_regs *)MMDC_P1_BASE_ADDR; /* Limit mem_speed for MX6D/MX6Q */ - if (is_cpu_type(MXC_CPU_MX6Q) || is_cpu_type(MXC_CPU_MX6D)) { + if (is_mx6dq() || is_mx6dqp()) { if (mem_speed > 1066) mem_speed = 1066; /* 1066 MT/s */ @@ -1221,7 +1219,7 @@ void mx6_ddr3_cfg(const struct mx6_ddr_sysinfo *sysinfo, * Data rate of 1066 MT/s requires 533 MHz DDR3 clock, but MX6D/Q supports * up to 528 MHz, so reduce the clock to fit chip specs */ - if (is_cpu_type(MXC_CPU_MX6Q) || is_cpu_type(MXC_CPU_MX6D)) { + if (is_mx6dq() || is_mx6dqp()) { if (clock > 528) clock = 528; /* 528 MHz */ } diff --git a/arch/arm/cpu/armv7/mx6/soc.c b/arch/arm/cpu/armv7/mx6/soc.c index d4b22ad..88fcfdc 100644 --- a/arch/arm/cpu/armv7/mx6/soc.c +++ b/arch/arm/cpu/armv7/mx6/soc.c @@ -108,6 +108,12 @@ u32 get_cpu_rev(void) #define OCOTP_CFG3_SPEED_1GHZ 2 #define OCOTP_CFG3_SPEED_1P2GHZ 3 +/* + * For i.MX6UL + */ +#define OCOTP_CFG3_SPEED_528MHZ 1 +#define OCOTP_CFG3_SPEED_696MHZ 2 + u32 get_cpu_speed_grade_hz(void) { struct ocotp_regs *ocotp = (struct ocotp_regs *)OCOTP_BASE_ADDR; @@ -120,17 +126,26 @@ u32 get_cpu_speed_grade_hz(void) val >>= OCOTP_CFG3_SPEED_SHIFT; val &= 0x3; + if (is_mx6ul()) { + if (val == OCOTP_CFG3_SPEED_528MHZ) + return 528000000; + else if (val == OCOTP_CFG3_SPEED_696MHZ) + return 69600000; + else + return 0; + } + switch (val) { /* Valid for IMX6DQ */ case OCOTP_CFG3_SPEED_1P2GHZ: - if (is_cpu_type(MXC_CPU_MX6Q) || is_cpu_type(MXC_CPU_MX6D)) + if (is_mx6dq() || is_mx6dqp()) return 1200000000; /* Valid for IMX6SX/IMX6SDL/IMX6DQ */ case OCOTP_CFG3_SPEED_1GHZ: return 996000000; /* Valid for IMX6DQ */ case OCOTP_CFG3_SPEED_850MHZ: - if (is_cpu_type(MXC_CPU_MX6Q) || is_cpu_type(MXC_CPU_MX6D)) + if (is_mx6dq() || is_mx6dqp()) return 852000000; /* Valid for IMX6SX/IMX6SDL/IMX6DQ */ case OCOTP_CFG3_SPEED_800MHZ: @@ -278,7 +293,7 @@ static void clear_mmdc_ch_mask(void) reg = readl(&mxc_ccm->ccdr); /* Clear MMDC channel mask */ - if (is_cpu_type(MXC_CPU_MX6SX) || is_cpu_type(MXC_CPU_MX6UL) || is_cpu_type(MXC_CPU_MX6SL)) + if (is_mx6sx() || is_mx6ul() || is_mx6sl()) reg &= ~(MXC_CCM_CCDR_MMDC_CH1_HS_MASK); else reg &= ~(MXC_CCM_CCDR_MMDC_CH1_HS_MASK | MXC_CCM_CCDR_MMDC_CH0_HS_MASK); @@ -444,8 +459,7 @@ void imx_get_mac_from_fuse(int dev_id, unsigned char *mac) struct fuse_bank4_regs *fuse = (struct fuse_bank4_regs *)bank->fuse_regs; - if ((is_cpu_type(MXC_CPU_MX6SX) || is_cpu_type(MXC_CPU_MX6UL)) && - dev_id == 1) { + if ((is_mx6sx() || is_mx6ul()) && dev_id == 1) { u32 value = readl(&fuse->mac_addr2); mac[0] = value >> 24 ; mac[1] = value >> 16 ; @@ -509,7 +523,7 @@ void s_init(void) u32 mask528; u32 reg, periph1, periph2; - if (is_cpu_type(MXC_CPU_MX6SX) || is_cpu_type(MXC_CPU_MX6UL)) + if (is_mx6sx() || is_mx6ul()) return; /* Due to hardware limitation, on MX6Q we need to gate/ungate all PFDs diff --git a/arch/arm/cpu/armv7/mx7/soc.c b/arch/arm/cpu/armv7/mx7/soc.c index 073bbc6..ef46c92 100644 --- a/arch/arm/cpu/armv7/mx7/soc.c +++ b/arch/arm/cpu/armv7/mx7/soc.c @@ -441,3 +441,11 @@ void s_init(void) return; } + +void reset_misc(void) +{ +#ifdef CONFIG_VIDEO_MXS + lcdif_power_down(); +#endif +} + diff --git a/arch/arm/imx-common/hab.c b/arch/arm/imx-common/hab.c index 8bbcc22..6731825 100644 --- a/arch/arm/imx-common/hab.c +++ b/arch/arm/imx-common/hab.c @@ -17,60 +17,55 @@ #define hab_rvt_report_event_p \ ( \ - ((is_cpu_type(MXC_CPU_MX6Q) || \ - is_cpu_type(MXC_CPU_MX6D)) && \ - (soc_rev() >= CHIP_REV_1_5)) ? \ + (is_mx6dqp()) ? \ ((hab_rvt_report_event_t *)HAB_RVT_REPORT_EVENT_NEW) : \ - (is_cpu_type(MXC_CPU_MX6DL) && \ - (soc_rev() >= CHIP_REV_1_2)) ? \ + (is_mx6dq() && (soc_rev() >= CHIP_REV_1_5)) ? \ + ((hab_rvt_report_event_t *)HAB_RVT_REPORT_EVENT_NEW) : \ + (is_mx6sdl() && (soc_rev() >= CHIP_REV_1_2)) ? \ ((hab_rvt_report_event_t *)HAB_RVT_REPORT_EVENT_NEW) : \ ((hab_rvt_report_event_t *)HAB_RVT_REPORT_EVENT) \ ) #define hab_rvt_report_status_p \ ( \ - ((is_cpu_type(MXC_CPU_MX6Q) || \ - is_cpu_type(MXC_CPU_MX6D)) && \ - (soc_rev() >= CHIP_REV_1_5)) ? \ + (is_mx6dqp()) ? \ + ((hab_rvt_report_status_t *)HAB_RVT_REPORT_STATUS_NEW) :\ + (is_mx6dq() && (soc_rev() >= CHIP_REV_1_5)) ? \ ((hab_rvt_report_status_t *)HAB_RVT_REPORT_STATUS_NEW) :\ - (is_cpu_type(MXC_CPU_MX6DL) && \ - (soc_rev() >= CHIP_REV_1_2)) ? \ + (is_mx6sdl() && (soc_rev() >= CHIP_REV_1_2)) ? \ ((hab_rvt_report_status_t *)HAB_RVT_REPORT_STATUS_NEW) :\ ((hab_rvt_report_status_t *)HAB_RVT_REPORT_STATUS) \ ) #define hab_rvt_authenticate_image_p \ ( \ - ((is_cpu_type(MXC_CPU_MX6Q) || \ - is_cpu_type(MXC_CPU_MX6D)) && \ - (soc_rev() >= CHIP_REV_1_5)) ? \ + (is_mx6dqp()) ? \ + ((hab_rvt_authenticate_image_t *)HAB_RVT_AUTHENTICATE_IMAGE_NEW) : \ + (is_mx6dq() && (soc_rev() >= CHIP_REV_1_5)) ? \ ((hab_rvt_authenticate_image_t *)HAB_RVT_AUTHENTICATE_IMAGE_NEW) : \ - (is_cpu_type(MXC_CPU_MX6DL) && \ - (soc_rev() >= CHIP_REV_1_2)) ? \ + (is_mx6sdl() && (soc_rev() >= CHIP_REV_1_2)) ? \ ((hab_rvt_authenticate_image_t *)HAB_RVT_AUTHENTICATE_IMAGE_NEW) : \ ((hab_rvt_authenticate_image_t *)HAB_RVT_AUTHENTICATE_IMAGE) \ ) #define hab_rvt_entry_p \ ( \ - ((is_cpu_type(MXC_CPU_MX6Q) || \ - is_cpu_type(MXC_CPU_MX6D)) && \ - (soc_rev() >= CHIP_REV_1_5)) ? \ + (is_mx6dqp()) ? \ ((hab_rvt_entry_t *)HAB_RVT_ENTRY_NEW) : \ - (is_cpu_type(MXC_CPU_MX6DL) && \ - (soc_rev() >= CHIP_REV_1_2)) ? \ + (is_mx6dq() && (soc_rev() >= CHIP_REV_1_5)) ? \ + ((hab_rvt_entry_t *)HAB_RVT_ENTRY_NEW) : \ + (is_mx6sdl() && (soc_rev() >= CHIP_REV_1_2)) ? \ ((hab_rvt_entry_t *)HAB_RVT_ENTRY_NEW) : \ ((hab_rvt_entry_t *)HAB_RVT_ENTRY) \ ) #define hab_rvt_exit_p \ ( \ - ((is_cpu_type(MXC_CPU_MX6Q) || \ - is_cpu_type(MXC_CPU_MX6D)) && \ - (soc_rev() >= CHIP_REV_1_5)) ? \ + (is_mx6dqp()) ? \ + ((hab_rvt_exit_t *)HAB_RVT_EXIT_NEW) : \ + (is_mx6dq() && (soc_rev() >= CHIP_REV_1_5)) ? \ ((hab_rvt_exit_t *)HAB_RVT_EXIT_NEW) : \ - (is_cpu_type(MXC_CPU_MX6DL) && \ - (soc_rev() >= CHIP_REV_1_2)) ? \ + (is_mx6sdl() && (soc_rev() >= CHIP_REV_1_2)) ? \ ((hab_rvt_exit_t *)HAB_RVT_EXIT_NEW) : \ ((hab_rvt_exit_t *)HAB_RVT_EXIT) \ ) @@ -424,8 +419,7 @@ uint32_t authenticate_image(uint32_t ddr_start, uint32_t image_size) */ /* Check MMU enabled */ if (is_soc_type(MXC_SOC_MX6) && get_cr() & CR_M) { - if (is_cpu_type(MXC_CPU_MX6Q) || - is_cpu_type(MXC_CPU_MX6D)) { + if (is_mx6dq()) { /* * This won't work on Rev 1.0.0 of * i.MX6Q/D, since their ROM doesn't @@ -434,10 +428,9 @@ uint32_t authenticate_image(uint32_t ddr_start, uint32_t image_size) */ if (!is_mx6dqp()) writel(1, MX6DQ_PU_IROM_MMU_EN_VAR); - } else if (is_cpu_type(MXC_CPU_MX6DL) || - is_cpu_type(MXC_CPU_MX6SOLO)) { + } else if (is_mx6sdl()) { writel(1, MX6DLS_PU_IROM_MMU_EN_VAR); - } else if (is_cpu_type(MXC_CPU_MX6SL)) { + } else if (is_mx6sl()) { writel(1, MX6SL_PU_IROM_MMU_EN_VAR); } } diff --git a/arch/arm/imx-common/init.c b/arch/arm/imx-common/init.c index 15dab1d..3d2ce3a 100644 --- a/arch/arm/imx-common/init.c +++ b/arch/arm/imx-common/init.c @@ -44,7 +44,7 @@ void init_aips(void) writel(0x00000000, &aips2->opacr3); writel(0x00000000, &aips2->opacr4); - if (is_cpu_type(MXC_CPU_MX6SX) || is_soc_type(MXC_SOC_MX7)) { + if (is_mx6sx() || is_mx7()) { /* * Set all MPROTx to be non-bufferable, trusted for R/W, * not forced to user-mode. @@ -78,8 +78,7 @@ void imx_set_wdog_powerdown(bool enable) writew(enable, &wdog1->wmcr); writew(enable, &wdog2->wmcr); - if (is_cpu_type(MXC_CPU_MX6SX) || is_cpu_type(MXC_CPU_MX6UL) || - is_soc_type(MXC_SOC_MX7)) + if (is_mx6sx() || is_mx6ul() || is_mx7()) writew(enable, &wdog3->wmcr); #ifdef CONFIG_MX7D writew(enable, &wdog4->wmcr); diff --git a/arch/arm/imx-common/iomux-v3.c b/arch/arm/imx-common/iomux-v3.c index 228d5f8..66137d1 100644 --- a/arch/arm/imx-common/iomux-v3.c +++ b/arch/arm/imx-common/iomux-v3.c @@ -83,7 +83,7 @@ void imx_iomux_v3_setup_multiple_pads(iomux_v3_cfg_t const *pad_list, #if defined(CONFIG_MX6QDL) stride = 2; - if (!is_cpu_type(MXC_CPU_MX6Q) && !is_cpu_type(MXC_CPU_MX6D)) + if (!is_mx6dq()) p += 1; #else stride = 1; diff --git a/arch/arm/imx-common/sata.c b/arch/arm/imx-common/sata.c index d174a46..acf9831 100644 --- a/arch/arm/imx-common/sata.c +++ b/arch/arm/imx-common/sata.c @@ -15,7 +15,7 @@ int setup_sata(void) struct iomuxc *const iomuxc_regs = (struct iomuxc *)IOMUXC_BASE_ADDR; int ret; - if (!is_cpu_type(MXC_CPU_MX6Q) && !is_cpu_type(MXC_CPU_MX6D)) + if (!is_mx6dq() && !is_mx6dqp()) return 1; ret = enable_sata_clock(); diff --git a/arch/arm/imx-common/timer.c b/arch/arm/imx-common/timer.c index 92c7218..a01590c 100644 --- a/arch/arm/imx-common/timer.c +++ b/arch/arm/imx-common/timer.c @@ -43,10 +43,8 @@ DECLARE_GLOBAL_DATA_PTR; static inline int gpt_has_clk_source_osc(void) { #if defined(CONFIG_MX6) - if (((is_cpu_type(MXC_CPU_MX6Q) || is_cpu_type(MXC_CPU_MX6D)) && - (soc_rev() > CHIP_REV_1_0)) || is_cpu_type(MXC_CPU_MX6DL) || - is_cpu_type(MXC_CPU_MX6SOLO) || is_cpu_type(MXC_CPU_MX6SX) || - is_cpu_type(MXC_CPU_MX6UL)) + if (((is_mx6dq()) && (soc_rev() > CHIP_REV_1_0)) || + is_mx6dqp() || is_mx6sdl() || is_mx6sx() || is_mx6ul()) return 1; return 0; @@ -86,10 +84,7 @@ int timer_init(void) i |= GPTCR_CLKSOURCE_OSC | GPTCR_TEN; /* For DL/S, SX, UL, set 24Mhz OSC Enable bit and prescaler */ - if (is_cpu_type(MXC_CPU_MX6DL) || - is_cpu_type(MXC_CPU_MX6SOLO) || - is_cpu_type(MXC_CPU_MX6SX) || - is_cpu_type(MXC_CPU_MX6UL)) { + if (is_mx6sdl() || is_mx6sx() || is_mx6ul()) { i |= GPTCR_24MEN; /* Produce 3Mhz clock */ diff --git a/arch/arm/include/asm/imx-common/sys_proto.h b/arch/arm/include/asm/imx-common/sys_proto.h index 386c2dc..32f95b3 100644 --- a/arch/arm/include/asm/imx-common/sys_proto.h +++ b/arch/arm/include/asm/imx-common/sys_proto.h @@ -24,7 +24,15 @@ #define is_cpu_type(cpu) (get_cpu_type() == cpu) #define is_soc_type(soc) (get_soc_type() == soc) +#define is_mx6() (is_soc_type(MXC_SOC_MX6)) +#define is_mx7() (is_soc_type(MXC_SOC_MX7)) + #define is_mx6dqp() (is_cpu_type(MXC_CPU_MX6QP) || is_cpu_type(MXC_CPU_MX6DP)) +#define is_mx6dq() (is_cpu_type(MXC_CPU_MX6Q) || is_cpu_type(MXC_CPU_MX6D)) +#define is_mx6sdl() (is_cpu_type(MXC_CPU_MX6SOLO) || is_cpu_type(MXC_CPU_MX6DL)) +#define is_mx6sx() (is_cpu_type(MXC_CPU_MX6SX)) +#define is_mx6sl() (is_cpu_type(MXC_CPU_MX6SL)) +#define is_mx6ul() (is_cpu_type(MXC_CPU_MX6UL)) u32 get_nr_cpus(void); u32 get_cpu_rev(void); diff --git a/board/freescale/mx6qsabreauto/mx6qsabreauto.c b/board/freescale/mx6qsabreauto/mx6qsabreauto.c index c2e9c57..d63a979 100644 --- a/board/freescale/mx6qsabreauto/mx6qsabreauto.c +++ b/board/freescale/mx6qsabreauto/mx6qsabreauto.c @@ -321,39 +321,6 @@ static void setup_gpmi_nand(void) } #endif -int mx6_rgmii_rework(struct phy_device *phydev) -{ - unsigned short val; - - /* To enable AR8031 ouput a 125MHz clk from CLK_25M */ - phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x7); - phy_write(phydev, MDIO_DEVAD_NONE, 0xe, 0x8016); - phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x4007); - - val = phy_read(phydev, MDIO_DEVAD_NONE, 0xe); - val &= 0xffe3; - val |= 0x18; - phy_write(phydev, MDIO_DEVAD_NONE, 0xe, val); - - /* introduce tx clock delay */ - phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x5); - val = phy_read(phydev, MDIO_DEVAD_NONE, 0x1e); - val |= 0x0100; - phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, val); - - return 0; -} - -int board_phy_config(struct phy_device *phydev) -{ - mx6_rgmii_rework(phydev); - - if (phydev->drv->config) - phydev->drv->config(phydev); - - return 0; -} - static void setup_fec(void) { if (is_mx6dqp()) { @@ -625,9 +592,9 @@ int board_late_init(void) if (is_mx6dqp()) setenv("board_rev", "MX6QP"); - else if (is_cpu_type(MXC_CPU_MX6Q) || is_cpu_type(MXC_CPU_MX6D)) + else if (is_mx6dq()) setenv("board_rev", "MX6Q"); - else if (is_cpu_type(MXC_CPU_MX6DL) || is_cpu_type(MXC_CPU_MX6SOLO)) + else if (is_mx6sdl()) setenv("board_rev", "MX6DL"); #endif diff --git a/board/freescale/mx6sabresd/mx6sabresd.c b/board/freescale/mx6sabresd/mx6sabresd.c index 2319354..54ba36b 100644 --- a/board/freescale/mx6sabresd/mx6sabresd.c +++ b/board/freescale/mx6sabresd/mx6sabresd.c @@ -649,9 +649,9 @@ int board_late_init(void) if (is_mx6dqp()) setenv("board_rev", "MX6QP"); - else if (is_cpu_type(MXC_CPU_MX6Q) || is_cpu_type(MXC_CPU_MX6D)) + else if (is_mx6dq()) setenv("board_rev", "MX6Q"); - else if (is_cpu_type(MXC_CPU_MX6DL) || is_cpu_type(MXC_CPU_MX6SOLO)) + else if (is_mx6sdl()) setenv("board_rev", "MX6DL"); #endif diff --git a/board/freescale/mx6slevk/mx6slevk.c b/board/freescale/mx6slevk/mx6slevk.c index f1915a8..256d602 100644 --- a/board/freescale/mx6slevk/mx6slevk.c +++ b/board/freescale/mx6slevk/mx6slevk.c @@ -230,14 +230,14 @@ int board_mmc_init(bd_t *bis) printf("Warning: you configured more USDHC controllers" "(%d) than supported by the board\n", i + 1); return -EINVAL; - } - - ret = fsl_esdhc_initialize(bis, &usdhc_cfg[i]); - if (ret) { - printf("Warning: failed to initialize " - "mmc dev %d\n", i); - return ret; - } + } + + ret = fsl_esdhc_initialize(bis, &usdhc_cfg[i]); + if (ret) { + printf("Warning: failed to initialize " + "mmc dev %d\n", i); + return ret; + } } return 0; diff --git a/board/gateworks/gw_ventana/README b/board/gateworks/gw_ventana/README index 9418907..f3f8998 100644 --- a/board/gateworks/gw_ventana/README +++ b/board/gateworks/gw_ventana/README @@ -173,13 +173,8 @@ OS load time which defeats the purpose of Falcon mode in the first place. The SPL decides to boot either U-Boot (u-boot.img) or the OS (args + kernel) based on the return value of the spl_start_uboot() function. While often this can simply be the state of a GPIO based pushbutton or DIP switch, for -Gateworks Ventana, we use the U-Boot environment 'boot_os' variable which if -set to '1' will choose to boot the OS rather than U-Boot. While the choice -of adding env support to the SPL adds a little bit of time to the boot -process as well as (significant really) SPL code space this was deemed most -flexible as within the large variety of Gateworks Ventana boards not all of -them have a user pushbutton and that pushbutton may be configured as a hard -reset per user configuration. +Gateworks Ventana, we use an EEPROM register on i2c-0 at 0x50:0x00: +set to '0' will choose to boot to U-Boot and otherwise it will boot to OS. To use Falcon mode it is required that you first 'prepare' the 'args' data that is stored on your boot medium along with the kernel (which can be any @@ -235,8 +230,8 @@ using rootfs (ubi), kernel (uImage), and dtb from the network: # flash args (at 17MB) Ventana > nand erase.part args && nand write 18000000 args 100000 - # set boot_os env var to enable booting to Linux - Ventana > setenv boot_os 1 && saveenv + # set i2c register 0x50:0x00=0 to boot to Linux + Ventana > i2c dev 0 && i2c mw 0x50 0x00.0 0 1 Be sure to adjust 'bootargs' above to your OS needs (this will be different for various distros such as OpenWrt, Yocto, Android, etc). You can use the @@ -309,8 +304,8 @@ out in U-Boot and use the following to enable Falcon mode: # write args 1MB data (0x800 sectors) to 1MB offset (0x800 sectors) Ventana > mmc write 18000000 0x800 0x800 - # set boot_os to enable falcon mode - Ventana > setenv boot_os 1 && saveenv + # set i2c register 0x50:0x00=0 to boot to Linux + Ventana > i2c dev 0 && i2c mw 0x50 0x00.0 0 1 Be sure to adjust 'bootargs' above to your OS needs (this will be different for various distros such as OpenWrt, Yocto, Android, etc). You can use the diff --git a/board/gateworks/gw_ventana/common.c b/board/gateworks/gw_ventana/common.c index a20190e..929dde9 100644 --- a/board/gateworks/gw_ventana/common.c +++ b/board/gateworks/gw_ventana/common.c @@ -132,10 +132,10 @@ void setup_ventana_i2c(void) /* common to add baseboards */ static iomux_v3_cfg_t const gw_gpio_pads[] = { - /* MSATA_EN */ - IOMUX_PADS(PAD_SD4_DAT0__GPIO2_IO08 | DIO_PAD_CFG), /* RS232_EN# */ IOMUX_PADS(PAD_SD4_DAT3__GPIO2_IO11 | DIO_PAD_CFG), + /* SD3_VSELECT */ + IOMUX_PADS(PAD_NANDF_CS1__GPIO6_IO14 | DIO_PAD_CFG), }; /* prototype */ @@ -183,6 +183,8 @@ static iomux_v3_cfg_t const gw51xx_gpio_pads[] = { }; static iomux_v3_cfg_t const gw52xx_gpio_pads[] = { + /* MSATA_EN */ + IOMUX_PADS(PAD_SD4_DAT0__GPIO2_IO08 | DIO_PAD_CFG), /* PANLEDG# */ IOMUX_PADS(PAD_KEY_COL0__GPIO4_IO06 | DIO_PAD_CFG), /* PANLEDR# */ @@ -212,6 +214,8 @@ static iomux_v3_cfg_t const gw52xx_gpio_pads[] = { }; static iomux_v3_cfg_t const gw53xx_gpio_pads[] = { + /* MSATA_EN */ + IOMUX_PADS(PAD_SD4_DAT0__GPIO2_IO08 | DIO_PAD_CFG), /* CAN_STBY */ IOMUX_PADS(PAD_GPIO_2__GPIO1_IO02 | DIO_PAD_CFG), /* USB_HUBRST# */ @@ -241,6 +245,8 @@ static iomux_v3_cfg_t const gw53xx_gpio_pads[] = { }; static iomux_v3_cfg_t const gw54xx_gpio_pads[] = { + /* MSATA_EN */ + IOMUX_PADS(PAD_SD4_DAT0__GPIO2_IO08 | DIO_PAD_CFG), /* CAN_STBY */ IOMUX_PADS(PAD_GPIO_2__GPIO1_IO02 | DIO_PAD_CFG), /* PANLEDG# */ @@ -283,6 +289,8 @@ static iomux_v3_cfg_t const gw551x_gpio_pads[] = { }; static iomux_v3_cfg_t const gw552x_gpio_pads[] = { + /* MSATA_EN */ + IOMUX_PADS(PAD_SD4_DAT0__GPIO2_IO08 | DIO_PAD_CFG), /* USBOTG_SEL */ IOMUX_PADS(PAD_GPIO_7__GPIO1_IO07 | DIO_PAD_CFG), /* USB_HUBRST# */ @@ -310,6 +318,20 @@ static iomux_v3_cfg_t const gw552x_gpio_pads[] = { IOMUX_PADS(PAD_GPIO_17__GPIO7_IO12 | DIO_PAD_CFG), }; +static iomux_v3_cfg_t const gw553x_gpio_pads[] = { + /* PANLEDG# */ + IOMUX_PADS(PAD_KEY_COL2__GPIO4_IO10 | DIO_PAD_CFG), + /* PANLEDR# */ + IOMUX_PADS(PAD_KEY_ROW2__GPIO4_IO11 | DIO_PAD_CFG), + + /* VID_PWR */ + IOMUX_PADS(PAD_CSI0_DATA_EN__GPIO5_IO20 | DIO_PAD_CFG), + /* PCI_RST# */ + IOMUX_PADS(PAD_GPIO_0__GPIO1_IO00 | DIO_PAD_CFG), + /* PCIESKT_WDIS# */ + IOMUX_PADS(PAD_GPIO_17__GPIO7_IO12 | DIO_PAD_CFG), +}; + /* * Board Specific GPIO @@ -445,6 +467,7 @@ struct ventana gpio_cfg[GW_UNKNOWN] = { .vidin_en = IMX_GPIO_NR(3, 31), .usb_sel = IMX_GPIO_NR(1, 2), .wdis = IMX_GPIO_NR(7, 12), + .msata_en = GP_MSATA_SEL, }, /* GW53xx */ @@ -489,6 +512,7 @@ struct ventana gpio_cfg[GW_UNKNOWN] = { .gps_shdn = IMX_GPIO_NR(1, 27), .vidin_en = IMX_GPIO_NR(3, 31), .wdis = IMX_GPIO_NR(7, 12), + .msata_en = GP_MSATA_SEL, }, /* GW54xx */ @@ -535,6 +559,7 @@ struct ventana gpio_cfg[GW_UNKNOWN] = { .dioi2c_en = IMX_GPIO_NR(4, 5), .pcie_sson = IMX_GPIO_NR(1, 20), .wdis = IMX_GPIO_NR(5, 17), + .msata_en = GP_MSATA_SEL, }, /* GW551x */ @@ -602,6 +627,47 @@ struct ventana gpio_cfg[GW_UNKNOWN] = { .pcie_rst = IMX_GPIO_NR(1, 29), .usb_sel = IMX_GPIO_NR(1, 7), .wdis = IMX_GPIO_NR(7, 12), + .msata_en = GP_MSATA_SEL, + }, + + /* GW553x */ + { + .gpio_pads = gw553x_gpio_pads, + .num_pads = ARRAY_SIZE(gw553x_gpio_pads)/2, + .dio_cfg = { + { + { IOMUX_PADS(PAD_SD1_DAT0__GPIO1_IO16) }, + IMX_GPIO_NR(1, 16), + { 0, 0 }, + 0 + }, + { + { IOMUX_PADS(PAD_SD1_DAT2__GPIO1_IO19) }, + IMX_GPIO_NR(1, 19), + { IOMUX_PADS(PAD_SD1_DAT2__PWM2_OUT) }, + 2 + }, + { + { IOMUX_PADS(PAD_SD1_DAT1__GPIO1_IO17) }, + IMX_GPIO_NR(1, 17), + { IOMUX_PADS(PAD_SD1_DAT1__PWM3_OUT) }, + 3 + }, + { + { IOMUX_PADS(PAD_SD1_CMD__GPIO1_IO18) }, + IMX_GPIO_NR(1, 18), + { IOMUX_PADS(PAD_SD1_CMD__PWM4_OUT) }, + 4 + }, + }, + .num_gpios = 4, + .leds = { + IMX_GPIO_NR(4, 10), + IMX_GPIO_NR(4, 11), + }, + .pcie_rst = IMX_GPIO_NR(1, 0), + .vidin_en = IMX_GPIO_NR(5, 20), + .wdis = IMX_GPIO_NR(7, 12), }, }; @@ -616,10 +682,6 @@ void setup_iomux_gpio(int board, struct ventana_board_info *info) gpio_request(GP_USB_OTG_PWR, "usbotg_pwr"); gpio_direction_output(GP_USB_OTG_PWR, 0); - /* MSATA Enable - default to PCI */ - gpio_request(GP_MSATA_SEL, "msata_en"); - gpio_direction_output(GP_MSATA_SEL, 0); - /* RS232_EN# */ gpio_request(GP_RS232_EN, "rs232_en"); gpio_direction_output(GP_RS232_EN, 0); @@ -649,6 +711,12 @@ void setup_iomux_gpio(int board, struct ventana_board_info *info) } } + /* MSATA Enable - default to PCI */ + if (gpio_cfg[board].msata_en) { + gpio_request(gpio_cfg[board].msata_en, "msata_en"); + gpio_direction_output(gpio_cfg[board].msata_en, 0); + } + /* Expansion Mezzanine IO */ if (gpio_cfg[board].mezz_pwren) { gpio_request(gpio_cfg[board].mezz_pwren, "mezz_pwr"); @@ -700,6 +768,11 @@ void setup_iomux_gpio(int board, struct ventana_board_info *info) gpio_request(gpio_cfg[board].wdis, "wlan_dis"); gpio_direction_output(gpio_cfg[board].wdis, 1); } + + /* sense vselect pin to see if we support uhs-i */ + gpio_request(GP_SD3_VSELECT, "sd3_vselect"); + gpio_direction_input(GP_SD3_VSELECT); + gpio_cfg[board].usd_vsel = !gpio_get_value(GP_SD3_VSELECT); } /* setup GPIO pinmux and default configuration per baseboard and env */ @@ -718,10 +791,9 @@ void setup_board_gpio(int board, struct ventana_board_info *info) gpio_direction_output(GP_RS232_EN, (hwconfig("rs232")) ? 0 : 1); /* MSATA Enable */ - if (is_cpu_type(MXC_CPU_MX6Q) && - test_bit(EECONFIG_SATA, info->config)) { + if (gpio_cfg[board].msata_en && is_cpu_type(MXC_CPU_MX6Q)) { gpio_direction_output(GP_MSATA_SEL, - (hwconfig("msata")) ? 1 : 0); + (hwconfig("msata")) ? 1 : 0); } /* USBOTG Select (PCISKT or FrontPanel) */ @@ -760,8 +832,13 @@ void setup_board_gpio(int board, struct ventana_board_info *info) ctrl); gpio_requestf(cfg->gpio_param, "dio%d", i); gpio_direction_input(cfg->gpio_param); - } else if (hwconfig_subarg_cmp("dio2", "mode", "pwm") && + } else if (hwconfig_subarg_cmp(arg, "mode", "pwm") && cfg->pwm_padmux) { + if (!cfg->pwm_param) { + printf("DIO%d: Error: pwm config invalid\n", + i); + continue; + } if (!quiet) printf("DIO%d: pwm%d\n", i, cfg->pwm_param); imx_iomux_v3_setup_pad(cfg->pwm_padmux[cputype] | @@ -770,8 +847,7 @@ void setup_board_gpio(int board, struct ventana_board_info *info) } if (!quiet) { - if (is_cpu_type(MXC_CPU_MX6Q) && - (test_bit(EECONFIG_SATA, info->config))) { + if (gpio_cfg[board].msata_en && is_cpu_type(MXC_CPU_MX6Q)) { printf("MSATA: %s\n", (hwconfig("msata") ? "enabled" : "disabled")); } diff --git a/board/gateworks/gw_ventana/common.h b/board/gateworks/gw_ventana/common.h index 28f5816..d037767 100644 --- a/board/gateworks/gw_ventana/common.h +++ b/board/gateworks/gw_ventana/common.h @@ -17,6 +17,7 @@ #define GP_SD3_CD IMX_GPIO_NR(7, 0) #define GP_RS232_EN IMX_GPIO_NR(2, 11) #define GP_MSATA_SEL IMX_GPIO_NR(2, 8) +#define GP_SD3_VSELECT IMX_GPIO_NR(6, 14) #define UART_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \ PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \ @@ -76,6 +77,8 @@ struct ventana { int pcie_sson; int usb_sel; int wdis; + int msata_en; + bool usd_vsel; }; extern struct ventana gpio_cfg[GW_UNKNOWN]; diff --git a/board/gateworks/gw_ventana/eeprom.c b/board/gateworks/gw_ventana/eeprom.c index ba15969..1382e5d 100644 --- a/board/gateworks/gw_ventana/eeprom.c +++ b/board/gateworks/gw_ventana/eeprom.c @@ -87,6 +87,9 @@ read_eeprom(int bus, struct ventana_board_info *info) } else if (info->model[4] == '2') { type = GW552x; break; + } else if (info->model[4] == '3') { + type = GW553x; + break; } /* fall through */ default: @@ -100,43 +103,12 @@ read_eeprom(int bus, struct ventana_board_info *info) /* list of config bits that the bootloader will remove from dtb if not set */ struct ventana_eeprom_config econfig[] = { { "eth0", "ethernet0", EECONFIG_ETH0 }, - { "eth1", "ethernet1", EECONFIG_ETH1 }, - { "sata", "ahci0", EECONFIG_SATA }, - { "pcie", NULL, EECONFIG_PCIE}, - { "lvds0", NULL, EECONFIG_LVDS0 }, - { "lvds1", NULL, EECONFIG_LVDS1 }, { "usb0", NULL, EECONFIG_USB0 }, { "usb1", NULL, EECONFIG_USB1 }, { "mmc0", NULL, EECONFIG_SD0 }, { "mmc1", NULL, EECONFIG_SD1 }, { "mmc2", NULL, EECONFIG_SD2 }, { "mmc3", NULL, EECONFIG_SD3 }, - { "uart0", NULL, EECONFIG_UART0 }, - { "uart1", NULL, EECONFIG_UART1 }, - { "uart2", NULL, EECONFIG_UART2 }, - { "uart3", NULL, EECONFIG_UART3 }, - { "uart4", NULL, EECONFIG_UART4 }, - { "ipu0", NULL, EECONFIG_IPU0 }, - { "ipu1", NULL, EECONFIG_IPU1 }, - { "can0", NULL, EECONFIG_FLEXCAN }, - { "i2c0", NULL, EECONFIG_I2C0 }, - { "i2c1", NULL, EECONFIG_I2C1 }, - { "i2c2", NULL, EECONFIG_I2C2 }, - { "vpu", NULL, EECONFIG_VPU }, - { "csi0", NULL, EECONFIG_CSI0 }, - { "csi1", NULL, EECONFIG_CSI1 }, - { "spi0", NULL, EECONFIG_ESPCI0 }, - { "spi1", NULL, EECONFIG_ESPCI1 }, - { "spi2", NULL, EECONFIG_ESPCI2 }, - { "spi3", NULL, EECONFIG_ESPCI3 }, - { "spi4", NULL, EECONFIG_ESPCI4 }, - { "spi5", NULL, EECONFIG_ESPCI5 }, - { "gps", "pps", EECONFIG_GPS }, - { "hdmi_in", NULL, EECONFIG_HDMI_IN }, - { "hdmi_out", NULL, EECONFIG_HDMI_OUT }, - { "cvbs_in", NULL, EECONFIG_VID_IN }, - { "cvbs_out", NULL, EECONFIG_VID_OUT }, - { "nand", NULL, EECONFIG_NAND }, { /* Sentinel */ } }; diff --git a/board/gateworks/gw_ventana/gsc.c b/board/gateworks/gw_ventana/gsc.c index 3febd12..2ca6d5c 100644 --- a/board/gateworks/gw_ventana/gsc.c +++ b/board/gateworks/gw_ventana/gsc.c @@ -11,6 +11,7 @@ #include <i2c.h> #include <linux/ctype.h> +#include "ventana_eeprom.h" #include "gsc.h" /* @@ -70,6 +71,8 @@ static void read_hwmon(const char *name, uint reg, uint size) puts("fRD\n"); } else { ui = buf[0] | (buf[1]<<8) | (buf[2]<<16); + if (reg == GSC_HWMON_TEMP && ui > 0x8000) + ui -= 0xffff; if (ui == 0xffffff) puts("invalid\n"); else @@ -79,7 +82,6 @@ static void read_hwmon(const char *name, uint reg, uint size) int gsc_info(int verbose) { - const char *model = getenv("model"); unsigned char buf[16]; i2c_set_bus_num(0); @@ -96,6 +98,12 @@ int gsc_info(int verbose) gsc_i2c_write(GSC_SC_ADDR, GSC_SC_STATUS, 1, &buf[GSC_SC_STATUS], 1); } + if (!gsc_i2c_read(GSC_HWMON_ADDR, GSC_HWMON_TEMP, 1, buf, 2)) { + int ui = buf[0] | buf[1]<<8; + if (ui > 0x8000) + ui -= 0xffff; + printf(" board temp at %dC", ui / 10); + } puts("\n"); if (!verbose) return CMD_RET_SUCCESS; @@ -109,10 +117,11 @@ int gsc_info(int verbose) read_hwmon("VDD_HIGH", GSC_HWMON_VDD_HIGH, 3); read_hwmon("VDD_DDR", GSC_HWMON_VDD_DDR, 3); read_hwmon("VDD_5P0", GSC_HWMON_VDD_5P0, 3); - read_hwmon("VDD_2P5", GSC_HWMON_VDD_2P5, 3); + if (strncasecmp((const char*) ventana_info.model, "GW553", 5)) + read_hwmon("VDD_2P5", GSC_HWMON_VDD_2P5, 3); read_hwmon("VDD_1P8", GSC_HWMON_VDD_1P8, 3); read_hwmon("VDD_IO2", GSC_HWMON_VDD_IO2, 3); - switch (model[3]) { + switch (ventana_info.model[3]) { case '1': /* GW51xx */ read_hwmon("VDD_IO3", GSC_HWMON_VDD_IO4, 3); /* -C rev */ break; @@ -160,6 +169,48 @@ int gsc_boot_wd_disable(void) } #ifdef CONFIG_CMD_GSC +static int do_gsc_sleep(cmd_tbl_t *cmdtp, int flag, int argc, + char * const argv[]) +{ + unsigned char reg; + unsigned long secs = 0; + + if (argc < 2) + return CMD_RET_USAGE; + + secs = simple_strtoul(argv[1], NULL, 10); + printf("GSC Sleeping for %ld seconds\n", secs); + + i2c_set_bus_num(0); + reg = (secs >> 24) & 0xff; + if (gsc_i2c_write(GSC_SC_ADDR, 9, 1, ®, 1)) + goto error; + reg = (secs >> 16) & 0xff; + if (gsc_i2c_write(GSC_SC_ADDR, 8, 1, ®, 1)) + goto error; + reg = (secs >> 8) & 0xff; + if (gsc_i2c_write(GSC_SC_ADDR, 7, 1, ®, 1)) + goto error; + reg = secs & 0xff; + if (gsc_i2c_write(GSC_SC_ADDR, 6, 1, ®, 1)) + goto error; + if (gsc_i2c_read(GSC_SC_ADDR, GSC_SC_CTRL1, 1, ®, 1)) + goto error; + reg |= (1 << 2); + if (gsc_i2c_write(GSC_SC_ADDR, GSC_SC_CTRL1, 1, ®, 1)) + goto error; + reg &= ~(1 << 2); + reg |= 0x3; + if (gsc_i2c_write(GSC_SC_ADDR, GSC_SC_CTRL1, 1, ®, 1)) + goto error; + + return CMD_RET_SUCCESS; + +error: + printf("i2c error\n"); + return CMD_RET_FAILURE; +} + static int do_gsc_wd(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) { unsigned char reg; @@ -206,13 +257,15 @@ static int do_gsc(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) if (strcasecmp(argv[1], "wd") == 0) return do_gsc_wd(cmdtp, flag, --argc, ++argv); + else if (strcasecmp(argv[1], "sleep") == 0) + return do_gsc_sleep(cmdtp, flag, --argc, ++argv); return CMD_RET_USAGE; } U_BOOT_CMD( gsc, 4, 1, do_gsc, "GSC configuration", - "[wd enable [30|60]]|[wd disable]\n" + "[wd enable [30|60]]|[wd disable]|[sleep <secs>]\n" ); #endif /* CONFIG_CMD_GSC */ diff --git a/board/gateworks/gw_ventana/gw_ventana.c b/board/gateworks/gw_ventana/gw_ventana.c index e2eeef3..70395ac 100644 --- a/board/gateworks/gw_ventana/gw_ventana.c +++ b/board/gateworks/gw_ventana/gw_ventana.c @@ -21,6 +21,7 @@ #include <asm/io.h> #include <dm.h> #include <dm/platform_data/serial_mxc.h> +#include <hwconfig.h> #include <i2c.h> #include <fdt_support.h> #include <fsl_esdhc.h> @@ -59,8 +60,7 @@ static iomux_v3_cfg_t const usdhc3_pads[] = { IOMUX_PADS(PAD_SD3_DAT1__SD3_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL)), IOMUX_PADS(PAD_SD3_DAT2__SD3_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL)), IOMUX_PADS(PAD_SD3_DAT3__SD3_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL)), - /* CD */ - IOMUX_PADS(PAD_SD3_DAT5__GPIO7_IO00 | MUX_PAD_CTRL(IRQ_PAD_CTRL)), + IOMUX_PADS(PAD_SD3_DAT5__GPIO7_IO00 | MUX_PAD_CTRL(USDHC_PAD_CTRL)), }; /* ENET */ @@ -266,7 +266,9 @@ int board_phy_config(struct phy_device *phydev) int board_eth_init(bd_t *bis) { #ifdef CONFIG_FEC_MXC - if (board_type != GW551x && board_type != GW552x) { + struct ventana_board_info *info = &ventana_info; + + if (test_bit(EECONFIG_ETH0, info->config)) { setup_iomux_enet(GP_PHY_RST); cpu_eth_init(bis); } @@ -317,6 +319,8 @@ static void enable_lvds(struct display_info_t const *dev) writel(reg, &iomux->gpr[2]); /* Enable Backlight */ + gpio_request(IMX_GPIO_NR(1, 10), "bklt_gpio"); + gpio_direction_output(IMX_GPIO_NR(1, 10), 0); gpio_request(IMX_GPIO_NR(1, 18), "bklt_en"); SETUP_IOMUX_PAD(PAD_SD1_CMD__GPIO1_IO18 | DIO_PAD_CFG); gpio_direction_output(IMX_GPIO_NR(1, 18), 1); @@ -456,8 +460,7 @@ static void setup_display(void) <<IOMUXC_GPR3_LVDS0_MUX_CTL_OFFSET); writel(reg, &iomux->gpr[3]); - /* Backlight CABEN on LVDS connector */ - gpio_request(IMX_GPIO_NR(1, 10), "bklt_gpio"); + /* LVDS Backlight GPIO on LVDS connector - output low */ SETUP_IOMUX_PAD(PAD_SD2_CLK__GPIO1_IO10 | DIO_PAD_CFG); gpio_direction_output(IMX_GPIO_NR(1, 10), 0); } @@ -697,7 +700,9 @@ int misc_init_r(void) setenv("model_base", str); sprintf(fdt, "%s-%s.dtb", cputype, str); setenv("fdt_file1", fdt); - if (board_type != GW551x && board_type != GW552x) + if (board_type != GW551x && + board_type != GW552x && + board_type != GW553x) str[4] = 'x'; str[5] = 'x'; str[6] = 0; @@ -776,6 +781,27 @@ static int ft_sethdmiinfmt(void *blob, char *mode) return 0; } +/* enable a property of a node if the node is found */ +static inline void ft_enable_path(void *blob, const char *path) +{ + int i = fdt_path_offset(blob, path); + if (i >= 0) { + debug("enabling %s\n", path); + fdt_status_okay(blob, i); + } +} + +/* remove a property of a node if the node is found */ +static inline void ft_delprop_path(void *blob, const char *path, + const char *name) +{ + int i = fdt_path_offset(blob, path); + if (i) { + debug("removing %s/%s\n", path, name); + fdt_delprop(blob, i, name); + } +} + /* * called prior to booting kernel or by 'fdt boardsetup' command * @@ -879,6 +905,11 @@ int ft_board_setup(void *blob, bd_t *bd) range[1] = cpu_to_fdt32(23); } } + + /* these have broken usd_vsel */ + if (strstr((const char *)info->model, "SP318-B") || + strstr((const char *)info->model, "SP331-B")) + gpio_cfg[board_type].usd_vsel = 0; } /* @@ -919,6 +950,32 @@ int ft_board_setup(void *blob, bd_t *bd) ft_sethdmiinfmt(blob, "yuv422bt656"); } + /* Configure DIO */ + for (i = 0; i < gpio_cfg[board_type].num_gpios; i++) { + struct dio_cfg *cfg = &gpio_cfg[board_type].dio_cfg[i]; + char arg[10]; + + sprintf(arg, "dio%d", i); + if (!hwconfig(arg)) + continue; + if (hwconfig_subarg_cmp(arg, "mode", "pwm") && cfg->pwm_param) + { + char path[48]; + sprintf(path, "/soc/aips-bus@02000000/pwm@%08x", + 0x02080000 + (0x4000 * (cfg->pwm_param - 1))); + printf(" Enabling pwm%d for DIO%d\n", + cfg->pwm_param, i); + ft_enable_path(blob, path); + } + } + + /* remove no-1-8-v if UHS-I support is present */ + if (gpio_cfg[board_type].usd_vsel) { + debug("Enabling UHS-I support\n"); + ft_delprop_path(blob, "/soc/aips-bus@02100000/usdhc@02198000", + "no-1-8-v"); + } + /* * Peripheral Config: * remove nodes by alias path if EEPROM config tells us the diff --git a/board/gateworks/gw_ventana/gw_ventana_spl.c b/board/gateworks/gw_ventana/gw_ventana_spl.c index 0a6ad47..e7f699a 100644 --- a/board/gateworks/gw_ventana/gw_ventana_spl.c +++ b/board/gateworks/gw_ventana/gw_ventana_spl.c @@ -15,6 +15,7 @@ #include <asm/imx-common/iomux-v3.h> #include <asm/imx-common/mxc_i2c.h> #include <environment.h> +#include <i2c.h> #include <spl.h> #include "gsc.h" @@ -189,6 +190,20 @@ static struct mx6_ddr3_cfg mt41k256m16ha_125 = { .trasmin = 3500, }; +/* MT41K512M16HA-125 (8Gb density) */ +static struct mx6_ddr3_cfg mt41k512m16ha_125 = { + .mem_speed = 1600, + .density = 8, + .width = 16, + .banks = 8, + .rowaddr = 16, + .coladdr = 10, + .pagesz = 2, + .trcd = 1375, + .trcmin = 4875, + .trasmin = 3500, +}; + /* * calibration - these are the various CPU/DDR3 combinations we support */ @@ -340,6 +355,19 @@ static struct mx6_mmdc_calibration mx6dq_256x64_mmdc_calib = { .p1_mpwrdlctl = 0X40304239, }; +static struct mx6_mmdc_calibration mx6dq_512x32_mmdc_calib = { + /* write leveling calibration determine */ + .p0_mpwldectrl0 = 0x002A0025, + .p0_mpwldectrl1 = 0x003A002A, + /* Read DQS Gating calibration */ + .p0_mpdgctrl0 = 0x43430356, + .p0_mpdgctrl1 = 0x033C0335, + /* Read Calibration: DQS delay relative to DQ read access */ + .p0_mprddlctl = 0x4B373F42, + /* Write Calibration: DQ/DM delay relative to DQS write access */ + .p0_mpwrdlctl = 0x303E3C36, +}; + static void spl_dram_init(int width, int size_mb, int board_model) { struct mx6_ddr3_cfg *mem = NULL; @@ -419,6 +447,11 @@ static void spl_dram_init(int width, int size_mb, int board_model) else calib = &mx6sdl_256x32_mmdc_calib; debug("4gB density\n"); + } else if (width == 32 && size_mb == 2048) { + mem = &mt41k512m16ha_125; + if (is_cpu_type(MXC_CPU_MX6Q)) + calib = &mx6dq_512x32_mmdc_calib; + debug("8gB density\n"); } else if (width == 64 && size_mb == 512) { mem = &mt41k64m16jt_125; debug("1gB density\n"); @@ -526,9 +559,6 @@ void board_init_f(ulong dummy) /* Clear the BSS. */ memset(__bss_start, 0, __bss_end - __bss_start); - - /* disable boot watchdog */ - gsc_boot_wd_disable(); } /* called from board_init_r after gd setup if CONFIG_SPL_BOARD_INIT defined */ @@ -560,7 +590,7 @@ void spl_board_init(void) /* return 1 if we wish to boot to uboot vs os (falcon mode) */ int spl_start_uboot(void) { - int ret = 1; + unsigned char ret = 1; debug("%s\n", __func__); #ifdef CONFIG_SPL_ENV_SUPPORT @@ -569,7 +599,14 @@ int spl_start_uboot(void) debug("boot_os=%s\n", getenv("boot_os")); if (getenv_yesno("boot_os") == 1) ret = 0; +#else + /* use i2c-0:0x50:0x00 for falcon boot mode (0=linux, else uboot) */ + i2c_set_bus_num(0); + gsc_i2c_read(0x50, 0x0, 1, &ret, 1); #endif + if (!ret) + gsc_boot_wd_disable(); + debug("%s booting %s\n", __func__, ret ? "uboot" : "linux"); return ret; } diff --git a/board/gateworks/gw_ventana/ventana_eeprom.h b/board/gateworks/gw_ventana/ventana_eeprom.h index daff375..9ffad58 100644 --- a/board/gateworks/gw_ventana/ventana_eeprom.h +++ b/board/gateworks/gw_ventana/ventana_eeprom.h @@ -111,6 +111,7 @@ enum { GW54xx, GW551x, GW552x, + GW553x, GW_UNKNOWN, GW_BADCRC, }; diff --git a/board/ge/bx50v3/bx50v3.c b/board/ge/bx50v3/bx50v3.c index ff8f4d7..d45ed44 100644 --- a/board/ge/bx50v3/bx50v3.c +++ b/board/ge/bx50v3/bx50v3.c @@ -601,6 +601,8 @@ int board_late_init(void) #ifdef CONFIG_CMD_BMODE add_board_boot_modes(board_boot_modes); #endif + +#ifdef CONFIG_VIDEO_IPUV3 /* We need at least 200ms between power on and backlight on * as per specifications from CHI MEI */ mdelay(250); @@ -615,6 +617,7 @@ int board_late_init(void) gpio_direction_output(LVDS_BACKLIGHT_GP, 1); pwm_enable(0); +#endif return 0; } diff --git a/configs/ge_b450v3_defconfig b/configs/ge_b450v3_defconfig index ffa0440..0ef418d 100644 --- a/configs/ge_b450v3_defconfig +++ b/configs/ge_b450v3_defconfig @@ -8,18 +8,18 @@ CONFIG_CMD_BOOTZ=y CONFIG_CMD_MMC=y CONFIG_CMD_SF=y CONFIG_CMD_I2C=y -CONFIG_CMD_USB=y -CONFIG_CMD_USB_MASS_STORAGE=y +CONFIG_CMD_FPGA=n CONFIG_CMD_GPIO=y -CONFIG_CMD_DHCP=y -CONFIG_CMD_MII=y -CONFIG_CMD_PING=y +CONFIG_CMD_NET=n +CONFIG_CMD_NFS=n CONFIG_CMD_CACHE=y CONFIG_CMD_EXT2=y CONFIG_CMD_EXT4=y CONFIG_CMD_EXT4_WRITE=y -CONFIG_CMD_FAT=y +CONFIG_CMD_FAT=n CONFIG_CMD_FS_GENERIC=y CONFIG_SPI_FLASH=y CONFIG_SPI_FLASH_STMICRO=y CONFIG_OF_LIBFDT=y +CONFIG_SYS_MALLOC_CLEAR_ON_INIT=n +CONFIG_EFI_LOADER=n diff --git a/configs/ge_b650v3_defconfig b/configs/ge_b650v3_defconfig index b039c24..2af4b11 100644 --- a/configs/ge_b650v3_defconfig +++ b/configs/ge_b650v3_defconfig @@ -8,18 +8,18 @@ CONFIG_CMD_BOOTZ=y CONFIG_CMD_MMC=y CONFIG_CMD_SF=y CONFIG_CMD_I2C=y -CONFIG_CMD_USB=y -CONFIG_CMD_USB_MASS_STORAGE=y +CONFIG_CMD_FPGA=n CONFIG_CMD_GPIO=y -CONFIG_CMD_DHCP=y -CONFIG_CMD_MII=y -CONFIG_CMD_PING=y +CONFIG_CMD_NET=n +CONFIG_CMD_NFS=n CONFIG_CMD_CACHE=y CONFIG_CMD_EXT2=y CONFIG_CMD_EXT4=y CONFIG_CMD_EXT4_WRITE=y -CONFIG_CMD_FAT=y +CONFIG_CMD_FAT=n CONFIG_CMD_FS_GENERIC=y CONFIG_SPI_FLASH=y CONFIG_SPI_FLASH_STMICRO=y CONFIG_OF_LIBFDT=y +CONFIG_SYS_MALLOC_CLEAR_ON_INIT=n +CONFIG_EFI_LOADER=n diff --git a/configs/ge_b850v3_defconfig b/configs/ge_b850v3_defconfig index d9c8acd..9e0c5eb 100644 --- a/configs/ge_b850v3_defconfig +++ b/configs/ge_b850v3_defconfig @@ -8,18 +8,18 @@ CONFIG_CMD_BOOTZ=y CONFIG_CMD_MMC=y CONFIG_CMD_SF=y CONFIG_CMD_I2C=y -CONFIG_CMD_USB=y -CONFIG_CMD_USB_MASS_STORAGE=y +CONFIG_CMD_FPGA=n CONFIG_CMD_GPIO=y -CONFIG_CMD_DHCP=y -CONFIG_CMD_MII=y -CONFIG_CMD_PING=y +CONFIG_CMD_NET=n +CONFIG_CMD_NFS=n CONFIG_CMD_CACHE=y CONFIG_CMD_EXT2=y CONFIG_CMD_EXT4=y CONFIG_CMD_EXT4_WRITE=y -CONFIG_CMD_FAT=y +CONFIG_CMD_FAT=n CONFIG_CMD_FS_GENERIC=y CONFIG_SPI_FLASH=y CONFIG_SPI_FLASH_STMICRO=y CONFIG_OF_LIBFDT=y +CONFIG_SYS_MALLOC_CLEAR_ON_INIT=n +CONFIG_EFI_LOADER=n diff --git a/drivers/block/dwc_ahsata.c b/drivers/block/dwc_ahsata.c index 6ec52a9..6056fe5 100644 --- a/drivers/block/dwc_ahsata.c +++ b/drivers/block/dwc_ahsata.c @@ -563,7 +563,7 @@ int init_sata(int dev) struct ahci_probe_ent *probe_ent = NULL; #if defined(CONFIG_MX6) - if (!is_cpu_type(MXC_CPU_MX6Q) && !is_cpu_type(MXC_CPU_MX6D)) + if (!is_mx6dq() && !is_mx6dqp()) return 1; #endif if (dev < 0 || dev > (CONFIG_SYS_SATA_MAX_DEVICE - 1)) { diff --git a/drivers/misc/mxc_ocotp.c b/drivers/misc/mxc_ocotp.c index 65ff815..38344e8 100644 --- a/drivers/misc/mxc_ocotp.c +++ b/drivers/misc/mxc_ocotp.c @@ -95,9 +95,9 @@ u32 fuse_bank_physical(int index) { u32 phy_index; - if (is_cpu_type(MXC_CPU_MX6SL)) { + if (is_mx6sl()) { phy_index = index; - } else if (is_cpu_type(MXC_CPU_MX6UL)) { + } else if (is_mx6ul()) { if (index >= 6) phy_index = fuse_bank_physical(5) + (index - 6) + 3; else diff --git a/drivers/mtd/nand/mxs_nand.c b/drivers/mtd/nand/mxs_nand.c index 7be1f86..c90a3a7 100644 --- a/drivers/mtd/nand/mxs_nand.c +++ b/drivers/mtd/nand/mxs_nand.c @@ -152,7 +152,7 @@ static inline uint32_t mxs_nand_get_ecc_strength(uint32_t page_data_size, int max_ecc_strength_supported; /* Refer to Chapter 17 for i.MX6DQ, Chapter 18 for i.MX6SX */ - if (is_cpu_type(MXC_CPU_MX6SX) || is_soc_type(MXC_SOC_MX7)) + if (is_mx6sx() || is_mx7()) max_ecc_strength_supported = 62; else max_ecc_strength_supported = 40; diff --git a/drivers/net/fec_mxc.c b/drivers/net/fec_mxc.c index 3340dd2..360f8e4 100644 --- a/drivers/net/fec_mxc.c +++ b/drivers/net/fec_mxc.c @@ -566,7 +566,7 @@ static int fec_init(struct eth_device *dev, bd_t* bd) /* Do not access reserved register for i.MX6UL */ - if (!is_cpu_type(MXC_CPU_MX6UL)) { + if (!is_mx6ul()) { /* clear MIB RAM */ for (i = mib_ptr; i <= mib_ptr + 0xfc; i += 4) writel(0, i); diff --git a/include/configs/ge_bx50v3.h b/include/configs/ge_bx50v3.h index 42771b5..4de2460 100644 --- a/include/configs/ge_bx50v3.h +++ b/include/configs/ge_bx50v3.h @@ -59,13 +59,14 @@ #define CONFIG_MXC_OCOTP /* SATA Configs */ -#define CONFIG_CMD_SATA +#ifdef CONFIG_CMD_SATA #define CONFIG_DWC_AHSATA #define CONFIG_SYS_SATA_MAX_DEVICE 1 #define CONFIG_DWC_AHSATA_PORT_ID 0 #define CONFIG_DWC_AHSATA_BASE_ADDR SATA_ARB_BASE_ADDR #define CONFIG_LBA48 #define CONFIG_LIBATA +#endif /* MMC Configs */ #define CONFIG_FSL_ESDHC @@ -77,6 +78,7 @@ #define CONFIG_DOS_PARTITION /* USB Configs */ +#ifdef CONFIG_USB #define CONFIG_USB_EHCI #define CONFIG_USB_EHCI_MX6 #define CONFIG_USB_STORAGE @@ -98,8 +100,10 @@ #define CONFIG_G_DNL_VENDOR_NUM 0x0525 #define CONFIG_G_DNL_PRODUCT_NUM 0xa4a5 #define CONFIG_G_DNL_MANUFACTURER "Advantech" +#endif /* Networking Configs */ +#ifdef CONFIG_NET #define CONFIG_FEC_MXC #define CONFIG_MII #define IMX_FEC_BASE ENET_BASE_ADDR @@ -108,6 +112,7 @@ #define CONFIG_FEC_MXC_PHYADDR 4 #define CONFIG_PHYLIB #define CONFIG_PHY_ATHEROS +#endif /* Serial Flash */ #ifdef CONFIG_CMD_SF @@ -220,29 +225,37 @@ "bootm; " \ "fi;\0" \ -#define CONFIG_BOOTCOMMAND \ - "usb start; " \ - "setenv dev usb; " \ - "setenv devnum 0; " \ - "setenv rootdev sda1; " \ - "run tryboot; " \ - \ +#define CONFIG_MMCBOOTCOMMAND \ "setenv dev mmc; " \ - "setenv rootdev mmcblk0p1; " \ + "setenv rootdev mmcblk0p${partnum}; " \ \ "setenv devnum ${sddev}; " \ "if mmc dev ${devnum}; then " \ "run tryboot; " \ - "setenv rootdev mmcblk1p1; " \ + "setenv rootdev mmcblk1p${partnum}; " \ "fi; " \ \ "setenv devnum ${emmcdev}; " \ "if mmc dev ${devnum}; then " \ "run tryboot; " \ "fi; " \ + +#define CONFIG_USBBOOTCOMMAND \ + "usb start; " \ + "setenv dev usb; " \ + "setenv devnum 0; " \ + "setenv rootdev sda${partnum}; " \ + "run tryboot; " \ \ + CONFIG_MMCBOOTCOMMAND \ "bmode usb; " \ +#ifdef CONFIG_CMD_USB +#define CONFIG_BOOTCOMMAND CONFIG_USBBOOTCOMMAND +#else +#define CONFIG_BOOTCOMMAND CONFIG_MMCBOOTCOMMAND +#endif + #define CONFIG_ARP_TIMEOUT 200UL /* Miscellaneous configurable options */ @@ -292,13 +305,14 @@ #define CONFIG_SYS_FSL_USDHC_NUM 3 +#define CONFIG_SYS_CONSOLE_IS_IN_ENV +#define CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE + /* Framebuffer */ -#define CONFIG_VIDEO +#ifdef CONFIG_VIDEO #define CONFIG_VIDEO_IPUV3 #define CONFIG_CFB_CONSOLE #define CONFIG_VGA_AS_SINGLE_DEVICE -#define CONFIG_SYS_CONSOLE_IS_IN_ENV -#define CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE #define CONFIG_VIDEO_BMP_RLE8 #define CONFIG_SPLASH_SCREEN #define CONFIG_SPLASH_SCREEN_ALIGN @@ -308,6 +322,7 @@ #define CONFIG_IPUV3_CLK 260000000 #define CONFIG_IMX_HDMI #define CONFIG_IMX_VIDEO_SKIP +#endif #define CONFIG_PWM_IMX #define CONFIG_IMX6_PWM_PER_CLK 66000000 diff --git a/include/configs/gw_ventana.h b/include/configs/gw_ventana.h index e11629c..982ddba 100644 --- a/include/configs/gw_ventana.h +++ b/include/configs/gw_ventana.h @@ -18,7 +18,6 @@ /* Falcon Mode */ #define CONFIG_CMD_SPL #define CONFIG_SPL_OS_BOOT -#define CONFIG_SPL_ENV_SUPPORT #define CONFIG_SYS_SPL_ARGS_ADDR 0x18000000 #define CONFIG_CMD_SPL_WRITE_SIZE (128 * SZ_1K) @@ -33,6 +32,7 @@ #include "imx6_spl.h" /* common IMX6 SPL configuration */ #include "mx6_common.h" +#undef CONFIG_SPL_EXT_SUPPORT #define CONFIG_MACH_TYPE 4520 /* Gateworks Ventana Platform */ @@ -52,9 +52,6 @@ #define CONFIG_DM_THERMAL #endif -/* GPIO */ -#define CONFIG_MXC_GPIO - /* Thermal */ #define CONFIG_IMX_THERMAL @@ -204,6 +201,7 @@ /* Miscellaneous configurable options */ #define CONFIG_HWCONFIG +#define CONFIG_PREBOOT /* Print Buffer Size */ #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) @@ -284,37 +282,45 @@ \ "mtdparts=" MTDPARTS_DEFAULT "\0" \ "mtdids=" MTDIDS_DEFAULT "\0" \ + "disk=0\0" \ + "part=1\0" \ \ "fdt_high=0xffffffff\0" \ "fdt_addr=0x18000000\0" \ "initrd_high=0xffffffff\0" \ + "fixfdt=" \ + "fdt addr ${fdt_addr}\0" \ "bootdir=boot\0" \ "loadfdt=" \ "if ${fsload} ${fdt_addr} ${bootdir}/${fdt_file}; then " \ "echo Loaded DTB from ${bootdir}/${fdt_file}; " \ + "run fixfdt; " \ "elif ${fsload} ${fdt_addr} ${bootdir}/${fdt_file1}; then " \ "echo Loaded DTB from ${bootdir}/${fdt_file1}; " \ + "run fixfdt; " \ "elif ${fsload} ${fdt_addr} ${bootdir}/${fdt_file2}; then " \ "echo Loaded DTB from ${bootdir}/${fdt_file2}; " \ + "run fixfdt; " \ "fi\0" \ \ + "fs=ext4\0" \ "script=6x_bootscript-ventana\0" \ "loadscript=" \ "if ${fsload} ${loadaddr} ${bootdir}/${script}; then " \ - "source; " \ + "source ${loadaddr}; " \ "fi\0" \ \ "uimage=uImage\0" \ - "mmc_root=/dev/mmcblk0p1 rootfstype=ext4 rootwait rw\0" \ + "mmc_root=/dev/mmcblk0p1 rootfstype=${fs} rootwait rw\0" \ "mmc_boot=" \ - "setenv fsload 'ext2load mmc 0:1'; " \ - "mmc dev 0 && mmc rescan && " \ + "setenv fsload \"${fs}load mmc ${disk}:${part}\"; " \ + "mmc dev ${disk} && mmc rescan && " \ "setenv dtype mmc; run loadscript; " \ "if ${fsload} ${loadaddr} ${bootdir}/${uimage}; then " \ "setenv bootargs console=${console},${baudrate} " \ - "root=/dev/mmcblk0p1 rootfstype=ext4 " \ + "root=/dev/mmcblk0p1 rootfstype=${fs} " \ "rootwait rw ${video} ${extra}; " \ - "if run loadfdt && fdt addr ${fdt_addr}; then " \ + "if run loadfdt; then " \ "bootm ${loadaddr} - ${fdt_addr}; " \ "else " \ "bootm; " \ @@ -322,26 +328,28 @@ "fi\0" \ \ "sata_boot=" \ - "setenv fsload 'ext2load sata 0:1'; sata init && " \ + "setenv fsload \"${fs}load sata ${disk}:${part}\"; " \ + "sata init && " \ "setenv dtype sata; run loadscript; " \ "if ${fsload} ${loadaddr} ${bootdir}/${uimage}; then " \ "setenv bootargs console=${console},${baudrate} " \ - "root=/dev/sda1 rootfstype=ext4 " \ + "root=/dev/sda1 rootfstype=${fs} " \ "rootwait rw ${video} ${extra}; " \ - "if run loadfdt && fdt addr ${fdt_addr}; then " \ + "if run loadfdt; then " \ "bootm ${loadaddr} - ${fdt_addr}; " \ "else " \ "bootm; " \ "fi; " \ "fi\0" \ "usb_boot=" \ - "setenv fsload 'ext2load usb 0:1'; usb start && usb dev 0 && " \ + "setenv fsload \"${fs}load usb ${disk}:${part}\"; " \ + "usb start && usb dev ${disk} && " \ "setenv dtype usb; run loadscript; " \ "if ${fsload} ${loadaddr} ${bootdir}/${uimage}; then " \ "setenv bootargs console=${console},${baudrate} " \ - "root=/dev/sda1 rootfstype=ext4 " \ + "root=/dev/sda1 rootfstype=${fs} " \ "rootwait rw ${video} ${extra}; " \ - "if run loadfdt && fdt addr ${fdt_addr}; then " \ + "if run loadfdt; then " \ "bootm ${loadaddr} - ${fdt_addr}; " \ "else " \ "bootm; " \ @@ -404,7 +412,7 @@ "if ${fsload} ${loadaddr} ${bootdir}/${uimage}; then " \ "setenv bootargs console=${console},${baudrate} " \ "root=${root} ${video} ${extra}; " \ - "if run loadfdt && fdt addr ${fdt_addr}; then " \ + "if run loadfdt; then " \ "ubifsumount; " \ "bootm ${loadaddr} - ${fdt_addr}; " \ "else " \ diff --git a/include/configs/ts4800.h b/include/configs/ts4800.h index 8b4726f..252b3fc 100644 --- a/include/configs/ts4800.h +++ b/include/configs/ts4800.h @@ -62,6 +62,8 @@ #define CONFIG_FSL_ESDHC #define CONFIG_SYS_FSL_ESDHC_ADDR MMC_SDHC1_BASE_ADDR +#define CONFIG_SYS_FSL_ERRATUM_ESDHC_A001 + #define CONFIG_MMC #define CONFIG_GENERIC_MMC @@ -95,19 +97,28 @@ #define CONFIG_EXTRA_ENV_SETTINGS \ "script=boot.scr\0" \ - "image=uImage\0" \ + "image=zImage\0" \ + "fdt_file=imx51-ts4800.dtb\0" \ + "fdt_addr=0x90fe0000\0" \ "mmcdev=0\0" \ - "mmcpart=1\0" \ - "mmcargs=setenv bootargs root=/dev/mmcblk0p2 rootwait rw\0" \ + "mmcpart=2\0" \ + "mmcroot=/dev/mmcblk0p3 rootwait rw\0" \ + "mmcargs=setenv bootargs root=${mmcroot}\0" \ "addtty=setenv bootargs ${bootargs} console=ttymxc0,${baudrate}\0" \ "loadbootscript=" \ "fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \ "bootscript=echo Running bootscript from mmc ...; " \ "source\0" \ "loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image};\0" \ + "loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \ "mmcboot=echo Booting from mmc ...; " \ "run mmcargs addtty; " \ - "bootm; " + "if run loadfdt; then " \ + "bootz ${loadaddr} - ${fdt_addr}; " \ + "else " \ + "echo ERR: cannot load FDT; " \ + "fi; " + #define CONFIG_BOOTCOMMAND \ "mmc dev ${mmcdev}; if mmc rescan; then " \ |