Merge branch 'master' of ssh://10.10.0.7/home/wd/git/u-boot/master

5 files changed, 866 insertions, 131 deletions

diff --git a/include/configs/MPC8544DS.h b/include/configs/MPC8544DS.h
index 5738192..612e8f2 100644
--- a/include/configs/MPC8544DS.h
+++ b/include/configs/MPC8544DS.h
@@ -196,7 +196,12 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #define PIXIS_VSPEED1		0x18	/* VELA VSpeed 1 */
 #define PIXIS_VCLKH		0x19	/* VELA VCLKH register */
 #define PIXIS_VCLKL		0x1A	/* VELA VCLKL register */
+#define PIXIS_VSPEED2		0x1d	/* VELA VSpeed 2 */
 #define CFG_PIXIS_VBOOT_MASK	0x40    /* Reset altbank mask*/
+#define PIXIS_VSPEED2_TSEC1SER	0x2
+#define PIXIS_VSPEED2_TSEC3SER	0x1
+#define PIXIS_VCFGEN1_TSEC1SER	0x20
+#define PIXIS_VCFGEN1_TSEC3SER	0x40
 
 
 /* define to use L1 as initial stack */
@@ -369,6 +374,9 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #define CONFIG_TSEC3	1
 #define CONFIG_TSEC3_NAME	"eTSEC3"
 
+#define CONFIG_FSL_SGMII_RISER	1
+#define SGMII_RISER_PHY_OFFSET	0x1c
+
 #define TSEC1_PHY_ADDR		0
 #define TSEC3_PHY_ADDR		1
 
diff --git a/include/configs/PLU405.h b/include/configs/PLU405.h
index a3d1c56..38c495e 100644
--- a/include/configs/PLU405.h
+++ b/include/configs/PLU405.h
@@ -57,7 +57,7 @@
 #define CONFIG_MII		1	/* MII PHY management		*/
 #define CONFIG_PHY_ADDR		0	/* PHY address			*/
 #define CONFIG_LXT971_NO_SLEEP  1       /* disable sleep mode in LXT971 */
-#define CONFIG_RESET_PHY_R      1       /* use reset_phy() to disable phy sleep mode */
+#define CONFIG_RESET_PHY_R      1       /* use reset_phy()              */
 
 #define CONFIG_PHY_CLK_FREQ	EMAC_STACR_CLK_66MHZ /* 66 MHz OPB clock*/
 
@@ -88,7 +88,10 @@
 #define CONFIG_CMD_MII
 #define CONFIG_CMD_PING
 #define CONFIG_CMD_EEPROM
+#define CONFIG_CMD_USB
 
+#define CONFIG_OF_LIBFDT
+#define CONFIG_OF_BOARD_SETUP
 
 #define CONFIG_MAC_PARTITION
 #define CONFIG_DOS_PARTITION
@@ -148,6 +151,7 @@
 
 #define CFG_HZ		1000		/* decrementer freq: 1 ms ticks */
 
+#define CONFIG_CMDLINE_EDITING	1	/* add command line history	*/
 #define CONFIG_ZERO_BOOTDELAY_CHECK	/* check for keypress on bootdelay==0 */
 #define CONFIG_BOOTDELAY	3	/* autoboot after 3 seconds	*/
 
@@ -164,11 +168,10 @@
 
 #define CFG_RX_ETH_BUFFER	16	/* use 16 rx buffer on 405 emac */
 
-/*-----------------------------------------------------------------------
+/*
  * NAND-FLASH stuff
- *-----------------------------------------------------------------------
  */
-#define CFG_NAND_BASE_LIST	{ CFG_NAND_BASE }
+#define CFG_NAND_BASE_LIST	{CFG_NAND_BASE}
 #define NAND_MAX_CHIPS          1
 #define CFG_MAX_NAND_DEVICE	1         /* Max number of NAND devices */
 #define NAND_BIG_DELAY_US	25
@@ -181,16 +184,15 @@
 #define CFG_NAND_SKIP_BAD_DOT_I 1       /* ".i" read skips bad blocks   */
 #define CFG_NAND_QUIET          1
 
-/*-----------------------------------------------------------------------
+/*
  * PCI stuff
- *-----------------------------------------------------------------------
  */
 #define PCI_HOST_ADAPTER 0              /* configure as pci adapter     */
 #define PCI_HOST_FORCE  1               /* configure as pci host        */
 #define PCI_HOST_AUTO   2               /* detected via arbiter enable  */
 
 #define CONFIG_PCI			/* include pci support	        */
-#define CONFIG_PCI_HOST	PCI_HOST_HOST   /* select pci host function     */
+#define CONFIG_PCI_HOST	PCI_HOST_FORCE  /* select pci host function     */
 #define CONFIG_PCI_PNP			/* do pci plug-and-play         */
 					/* resource configuration       */
 
@@ -206,134 +208,132 @@
 #define CFG_PCI_PTM1PCI 0x00000000      /* Host: use this pci address   */
 #define CFG_PCI_PTM2LA  0xffc00000      /* point to flash               */
 #define CFG_PCI_PTM2MS  0xffc00001      /* 4MB, enable                  */
-#define CFG_PCI_PTM2PCI 0x04000000      /* Host: use this pci address   */
+#define CFG_PCI_PTM2PCI 0x08000000      /* Host: use this pci address   */
 
-/*-----------------------------------------------------------------------
+/*
  * IDE/ATA stuff
- *-----------------------------------------------------------------------
  */
 #undef	CONFIG_IDE_8xx_DIRECT		    /* no pcmcia interface required */
 #undef	CONFIG_IDE_LED			/* no led for ide supported	*/
 #define CONFIG_IDE_RESET	1	/* reset for ide supported	*/
 
 #define CFG_IDE_MAXBUS		1		/* max. 1 IDE busses	*/
-#define CFG_IDE_MAXDEVICE	(CFG_IDE_MAXBUS*1) /* max. 1 drives per IDE bus */
+/* max. 1 drives per IDE bus */
+#define CFG_IDE_MAXDEVICE	(CFG_IDE_MAXBUS*1)
 
 #define CFG_ATA_BASE_ADDR	0xF0100000
 #define CFG_ATA_IDE0_OFFSET	0x0000
 
-#define CFG_ATA_DATA_OFFSET	0x0000	/* Offset for data I/O			*/
-#define CFG_ATA_REG_OFFSET	0x0000	/* Offset for normal register accesses	*/
-#define CFG_ATA_ALT_OFFSET	0x0000	/* Offset for alternate registers	*/
+#define CFG_ATA_DATA_OFFSET	0x0000	/* Offset for data I/O */
+#define CFG_ATA_REG_OFFSET	0x0000	/* Offset for normal register access */
+#define CFG_ATA_ALT_OFFSET	0x0000	/* Offset for alternate registers */
 
 /*
  * For booting Linux, the board info and command line data
  * have to be in the first 8 MB of memory, since this is
  * the maximum mapped by the Linux kernel during initialization.
  */
-#define CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
-/*-----------------------------------------------------------------------
+#define CFG_BOOTMAPSZ		(8 << 20) /* Initial Memory map for Linux */
+
+/*
  * FLASH organization
  */
-#define FLASH_BASE0_PRELIM	0xFFC00000	/* FLASH bank #0	*/
+#define FLASH_BASE0_PRELIM	0xFFC00000 /* FLASH bank #0 */
 
-#define CFG_MAX_FLASH_BANKS	1	/* max number of memory banks		*/
-#define CFG_MAX_FLASH_SECT	256	/* max number of sectors on one chip	*/
+#define CFG_MAX_FLASH_BANKS	1	/* max number of memory banks */
+#define CFG_MAX_FLASH_SECT	256	/* max number of sectors on one chip */
 
-#define CFG_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
-#define CFG_FLASH_WRITE_TOUT	1000	/* Timeout for Flash Write (in ms)	*/
+#define CFG_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms) */
+#define CFG_FLASH_WRITE_TOUT	1000	/* Timeout for Flash Write (in ms) */
 
-#define CFG_FLASH_WORD_SIZE	unsigned short	/* flash word size (width)	*/
-#define CFG_FLASH_ADDR0		0x5555	/* 1st address for flash config cycles	*/
-#define CFG_FLASH_ADDR1		0x2AAA	/* 2nd address for flash config cycles	*/
+#define CFG_FLASH_WORD_SIZE	unsigned short	/* flash word size (width) */
+#define CFG_FLASH_ADDR0		0x5555	/* 1st addr for flash config cycles */
+#define CFG_FLASH_ADDR1		0x2AAA	/* 2nd addr for flash config cycles */
 /*
  * The following defines are added for buggy IOP480 byte interface.
  * All other boards should use the standard values (CPCI405 etc.)
  */
-#define CFG_FLASH_READ0		0x0000	/* 0 is standard			*/
-#define CFG_FLASH_READ1		0x0001	/* 1 is standard			*/
-#define CFG_FLASH_READ2		0x0002	/* 2 is standard			*/
+#define CFG_FLASH_READ0		0x0000	/* 0 is standard */
+#define CFG_FLASH_READ1		0x0001	/* 1 is standard */
+#define CFG_FLASH_READ2		0x0002	/* 2 is standard */
 
-#define CFG_FLASH_EMPTY_INFO		/* print 'E' for empty sector on flinfo */
+#define CFG_FLASH_EMPTY_INFO		/* print 'E' for empty sector */
 
-/*-----------------------------------------------------------------------
+/*
  * Start addresses for the final memory configuration
  * (Set up by the startup code)
  * Please note that CFG_SDRAM_BASE _must_ start at 0
  */
 #define CFG_SDRAM_BASE		0x00000000
-#define CFG_FLASH_BASE		0xFFFC0000
+#define CFG_FLASH_BASE		0xFFFA0000
 #define CFG_MONITOR_BASE	TEXT_BASE
-#define CFG_MONITOR_LEN		(256 * 1024)	/* Reserve 256 kB for Monitor	*/
-#define CFG_MALLOC_LEN		(256 * 1024)	/* Reserve 256 kB for malloc()	*/
+#define CFG_MONITOR_LEN		(384 * 1024)	/* Reserve 384kB for Monitor */
+#define CFG_MALLOC_LEN		(384 * 1024)	/* Reserve 384kB for malloc() */
 
-#if (CFG_MONITOR_BASE < FLASH_BASE0_PRELIM)
-# define CFG_RAMBOOT		1
-#else
-# undef CFG_RAMBOOT
-#endif
-
-/*-----------------------------------------------------------------------
+/*
  * Environment Variable setup
  */
 #define CFG_ENV_IS_IN_EEPROM	1	/* use EEPROM for environment vars */
-#define CFG_ENV_OFFSET		0x100	/* environment starts at the beginning of the EEPROM */
-#define CFG_ENV_SIZE		0x700	/* 2048 bytes may be used for env vars*/
-				   /* total size of a CAT24WC16 is 2048 bytes */
+#define CFG_ENV_OFFSET		0x100	/* reseve 0x100 bytes for strapping */
+#define CFG_ENV_SIZE		0x700
 
-/*-----------------------------------------------------------------------
- * I2C EEPROM (CAT24WC16) for environment
+/*
+ * I2C EEPROM (24WC16) for environment
  */
 #define CONFIG_HARD_I2C			/* I2c with hardware support */
 #define CFG_I2C_SPEED		400000	/* I2C speed and slave address */
 #define CFG_I2C_SLAVE		0x7F
 
-#define CFG_I2C_EEPROM_ADDR	0x50	/* EEPROM CAT24WC08		*/
+#define CFG_I2C_EEPROM_ADDR	0x50	/* EEPROM 24WC16 */
 #define CFG_EEPROM_WREN         1
 
-/* CAT24WC08/16... */
+/* 24WC16 */
 #define CFG_I2C_EEPROM_ADDR_LEN 1	/* Bytes of address		*/
-/* mask of address bits that overflow into the "EEPROM chip address"	*/
+/* mask of address bits that overflow into the "EEPROM chip address"    */
 #define CFG_I2C_EEPROM_ADDR_OVERFLOW	0x07
-#define CFG_EEPROM_PAGE_WRITE_BITS 4	/* The Catalyst CAT24WC08 has	*/
-					/* 16 byte page write mode using*/
-					/* last 4 bits of the address	*/
+#define CFG_EEPROM_PAGE_WRITE_BITS 4	/* The 24WC16 has   */
+					/* 16 byte page write mode using */
+					/* last 4 bits of the address   */
 #define CFG_EEPROM_PAGE_WRITE_DELAY_MS	10   /* and takes up to 10 msec */
 #define CFG_EEPROM_PAGE_WRITE_ENABLE
 
-/*-----------------------------------------------------------------------
+/*
  * External Bus Controller (EBC) Setup
  */
-
-#define CAN_BA		0xF0000000	    /* CAN Base Address			*/
-#define DUART0_BA	0xF0000400	    /* DUART Base Address		*/
-#define DUART1_BA	0xF0000408	    /* DUART Base Address		*/
-#define RTC_BA		0xF0000500	    /* RTC Base Address			*/
-#define VGA_BA		0xF1000000	    /* Epson VGA Base Address		*/
-#define CFG_NAND_BASE	0xF4000000	    /* NAND FLASH Base Address		*/
-
-/* Memory Bank 0 (Flash Bank 0, NOR-FLASH) initialization			*/
+#define CAN_BA		0xF0000000	    /* CAN Base Address	        */
+#define DUART0_BA	0xF0000400	    /* DUART Base Address       */
+#define DUART1_BA	0xF0000408	    /* DUART Base Address       */
+#define RTC_BA		0xF0000500	    /* RTC Base Address         */
+#define VGA_BA		0xF1000000	    /* Epson VGA Base Address   */
+#define CFG_NAND_BASE	0xF4000000	    /* NAND FLASH Base Address  */
+
+/* Memory Bank 0 (Flash Bank 0, NOR-FLASH) initialization */
+/* TWT=16,CSN=1,OEN=1,WBN=1,WBF=1,TH=4,SOR=1 */
 #define CFG_EBC_PB0AP		0x92015480
-/*#define CFG_EBC_PB0AP		  0x08055880  /XXX* TWT=16,CSN=1,OEN=1,WBN=1,WBF=1,TH=4,SOR=1 */
-#define CFG_EBC_PB0CR		0xFFC5A000  /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */
+/* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */
+#define CFG_EBC_PB0CR		0xFFC5A000
 
-/* Memory Bank 1 (Flash Bank 1, NAND-FLASH) initialization			*/
+/* Memory Bank 1 (Flash Bank 1, NAND-FLASH) initialization */
 #define CFG_EBC_PB1AP		0x92015480
-#define CFG_EBC_PB1CR		0xF4018000  /* BAS=0xF40,BS=1MB,BU=R/W,BW=8bit	*/
+/* BAS=0xF40,BS=1MB,BU=R/W,BW=8bit */
+#define CFG_EBC_PB1CR		0xF4018000
 
-/* Memory Bank 2 (8 Bit Peripheral: CAN, UART, RTC) initialization		*/
-#define CFG_EBC_PB2AP		0x010053C0  /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
-#define CFG_EBC_PB2CR		0xF0018000  /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit	*/
+/* Memory Bank 2 (8 Bit Peripheral: CAN, UART, RTC) initialization */
+/* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
+#define CFG_EBC_PB2AP		0x010053C0
+/* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit */
+#define CFG_EBC_PB2CR		0xF0018000
 
-/* Memory Bank 3 (16 Bit Peripheral: FPGA internal, dig. IO) initialization	*/
-#define CFG_EBC_PB3AP		0x010053C0  /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
-#define CFG_EBC_PB3CR		0xF011A000  /* BAS=0xF01,BS=1MB,BU=R/W,BW=16bit */
+/* Memory Bank 3 (16 Bit Peripheral: FPGA internal, dig. IO) initialization */
+/* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
+#define CFG_EBC_PB3AP		0x010053C0
+/* BAS=0xF01,BS=1MB,BU=R/W,BW=16bit */
+#define CFG_EBC_PB3CR		0xF011A000
 
-/*-----------------------------------------------------------------------
+/*
  * FPGA stuff
  */
-
-#define CFG_FPGA_BASE_ADDR 0xF0100100	    /* FPGA internal Base Address	*/
+#define CFG_FPGA_BASE_ADDR 0xF0100100	    /* FPGA internal Base Address */
 
 /* FPGA internal regs */
 #define CFG_FPGA_CTRL		0x000
@@ -343,17 +343,17 @@
 #define CFG_FPGA_CTRL_WDI	0x0002
 #define CFG_FPGA_CTRL_PS2_RESET 0x0020
 
-#define CFG_FPGA_SPARTAN2	1	    /* using Xilinx Spartan 2 now    */
+#define CFG_FPGA_SPARTAN2	1	    /* using Xilinx Spartan 2 now */
 #define CFG_FPGA_MAX_SIZE	128*1024    /* 128kByte is enough for XC2S50E*/
 
 /* FPGA program pin configuration */
 #define CFG_FPGA_PRG		0x04000000  /* FPGA program pin (ppc output) */
-#define CFG_FPGA_CLK		0x02000000  /* FPGA clk pin (ppc output)     */
-#define CFG_FPGA_DATA		0x01000000  /* FPGA data pin (ppc output)    */
-#define CFG_FPGA_INIT		0x00010000  /* FPGA init pin (ppc input)     */
-#define CFG_FPGA_DONE		0x00008000  /* FPGA done pin (ppc input)     */
+#define CFG_FPGA_CLK		0x02000000  /* FPGA clk pin (ppc output) */
+#define CFG_FPGA_DATA		0x01000000  /* FPGA data pin (ppc output) */
+#define CFG_FPGA_INIT		0x00010000  /* FPGA init pin (ppc input) */
+#define CFG_FPGA_DONE		0x00008000  /* FPGA done pin (ppc input) */
 
-/*-----------------------------------------------------------------------
+/*
  * Definitions for initial stack pointer and data area (in data cache)
  */
 /* use on chip memory ( OCM ) for temperary stack until sdram is tested */
@@ -362,14 +362,14 @@
 /* On Chip Memory location */
 #define CFG_OCM_DATA_ADDR	0xF8000000
 #define CFG_OCM_DATA_SIZE	0x1000
-#define CFG_INIT_RAM_ADDR	CFG_OCM_DATA_ADDR /* inside of SDRAM		*/
-#define CFG_INIT_RAM_END	CFG_OCM_DATA_SIZE /* End of used area in RAM	*/
+#define CFG_INIT_RAM_ADDR	CFG_OCM_DATA_ADDR /* inside of SDRAM */
+#define CFG_INIT_RAM_END	CFG_OCM_DATA_SIZE /* End of used area in RAM  */
 
-#define CFG_GBL_DATA_SIZE      128  /* size in bytes reserved for initial data */
+#define CFG_GBL_DATA_SIZE      128 /* size in bytes reserved for initial data */
 #define CFG_GBL_DATA_OFFSET    (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
 #define CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET
 
-/*-----------------------------------------------------------------------
+/*
  * Definitions for GPIO setup (PPC405EP specific)
  *
  * GPIO0[0]	- External Bus Controller BLAST output
@@ -397,14 +397,14 @@
  *
  * Boot Flags
  */
-#define BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH	*/
-#define BOOTFLAG_WARM	0x02		/* Software reboot			*/
+#define BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM	0x02		/* Software reboot */
 
 /*
- * Default speed selection (cpu_plb_opb_ebc) in mhz.
+ * Default speed selection (cpu_plb_opb_ebc) in MHz.
  * This value will be set if iic boot eprom is disabled.
  */
-#if 0
+#if 1
 #define PLLMR0_DEFAULT	 PLLMR0_266_133_66_33
 #define PLLMR1_DEFAULT	 PLLMR1_266_133_66_33
 #endif
@@ -412,9 +412,19 @@
 #define PLLMR0_DEFAULT	 PLLMR0_200_100_50_33
 #define PLLMR1_DEFAULT	 PLLMR1_200_100_50_33
 #endif
-#if 1
+#if 0
 #define PLLMR0_DEFAULT	 PLLMR0_133_66_66_33
 #define PLLMR1_DEFAULT	 PLLMR1_133_66_66_33
 #endif
 
+/*
+ * PCI OHCI controller
+ */
+#define CONFIG_USB_OHCI_NEW	1
+#define CONFIG_PCI_OHCI		1
+#define CFG_OHCI_SWAP_REG_ACCESS 1
+#define CFG_USB_OHCI_MAX_ROOT_PORTS 15
+#define CFG_USB_OHCI_SLOT_NAME	"ohci_pci"
+#define CONFIG_USB_STORAGE	1
+
 #endif	/* __CONFIG_H */
diff --git a/include/configs/VOM405.h b/include/configs/VOM405.h
index ec6f205..f235890 100644
--- a/include/configs/VOM405.h
+++ b/include/configs/VOM405.h
@@ -24,7 +24,6 @@
 /*
  * board/config.h - configuration options, board specific
  */
-
 #ifndef __CONFIG_H
 #define __CONFIG_H
 
@@ -32,7 +31,6 @@
  * High Level Configuration Options
  * (easy to change)
  */
-
 #define CONFIG_405EP		1	/* This is a PPC405 CPU		*/
 #define CONFIG_4xx		1	/* ...member of PPC4xx family	*/
 #define CONFIG_VOM405		1	/* ...on a VOM405 board		*/
@@ -71,7 +69,6 @@
 #define CONFIG_BOOTP_DNS2
 #define CONFIG_BOOTP_SEND_HOSTNAME
 
-
 /*
  * Command line configuration.
  */
@@ -79,7 +76,6 @@
 
 #define CONFIG_CMD_DHCP
 #define CONFIG_CMD_BSP
-#define CONFIG_CMD_PCI
 #define CONFIG_CMD_IRQ
 #define CONFIG_CMD_ELF
 #define CONFIG_CMD_I2C
@@ -87,6 +83,8 @@
 #define CONFIG_CMD_PING
 #define CONFIG_CMD_EEPROM
 
+#define CONFIG_OF_LIBFDT
+#define CONFIG_OF_BOARD_SETUP
 
 #undef	CONFIG_WATCHDOG			/* watchdog disabled		*/
 
@@ -136,44 +134,20 @@
 
 #define CFG_HZ		1000		/* decrementer freq: 1 ms ticks */
 
+#define CONFIG_CMDLINE_EDITING	1	/* add command line history	*/
 #define CONFIG_ZERO_BOOTDELAY_CHECK	/* check for keypress on bootdelay==0 */
 
 #define CONFIG_VERSION_VARIABLE 1	/* include version env variable */
 
 #define CFG_RX_ETH_BUFFER	16	/* use 16 rx buffer on 405 emac */
 
-/*-----------------------------------------------------------------------
- * PCI stuff
- *-----------------------------------------------------------------------
- */
-#define PCI_HOST_ADAPTER 0		/* configure as pci adapter	*/
-#define PCI_HOST_FORCE	1		/* configure as pci host	*/
-#define PCI_HOST_AUTO	2		/* detected via arbiter enable	*/
-
-#define CONFIG_PCI			/* include pci support		*/
-#define CONFIG_PCI_HOST PCI_HOST_HOST	/* select pci host function	*/
-#undef	CONFIG_PCI_PNP			/* do pci plug-and-play		*/
-					/* resource configuration	*/
-
-#undef	CONFIG_PCI_SCAN_SHOW		/* print pci devices @ startup	*/
-
-#define CFG_PCI_SUBSYS_VENDORID 0x12FE	/* PCI Vendor ID: esd gmbh	*/
-#define CFG_PCI_SUBSYS_DEVICEID 0x0405	/* PCI Device ID: CPCI-405	*/
-#define CFG_PCI_CLASSCODE	0x0b20	/* PCI Class Code: Processor/PPC*/
-#define CFG_PCI_PTM1LA	0x00000000	/* point to sdram		*/
-#define CFG_PCI_PTM1MS	0xfc000001	/* 64MB, enable hard-wired to 1 */
-#define CFG_PCI_PTM1PCI 0x00000000	/* Host: use this pci address	*/
-#define CFG_PCI_PTM2LA	0xffc00000	/* point to flash		*/
-#define CFG_PCI_PTM2MS	0xffc00001	/* 4MB, enable			*/
-#define CFG_PCI_PTM2PCI 0x04000000	/* Host: use this pci address	*/
-
 /*
  * For booting Linux, the board info and command line data
  * have to be in the first 8 MB of memory, since this is
  * the maximum mapped by the Linux kernel during initialization.
  */
 #define CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
-/*-----------------------------------------------------------------------
+/*
  * FLASH organization
  */
 #define FLASH_BASE0_PRELIM	0xFFC00000	/* FLASH bank #0	*/
@@ -197,12 +171,7 @@
 
 #define CFG_FLASH_EMPTY_INFO		/* print 'E' for empty sector on flinfo */
 
-#if 0 /* test-only */
-#define CFG_JFFS2_FIRST_BANK	0	    /* use for JFFS2 */
-#define CFG_JFFS2_NUM_BANKS	1	    /* ! second bank contains U-Boot */
-#endif
-
-/*-----------------------------------------------------------------------
+/*
  * Start addresses for the final memory configuration
  * (Set up by the startup code)
  * Please note that CFG_SDRAM_BASE _must_ start at 0
@@ -219,7 +188,7 @@
 # undef CFG_RAMBOOT
 #endif
 
-/*-----------------------------------------------------------------------
+/*
  * Environment Variable setup
  */
 #define CFG_ENV_IS_IN_EEPROM	1	/* use EEPROM for environment vars */
@@ -230,7 +199,7 @@
 #define CFG_NVRAM_BASE_ADDR	0xF0000500		/* NVRAM base address	*/
 #define CFG_NVRAM_SIZE		242			/* NVRAM size		*/
 
-/*-----------------------------------------------------------------------
+/*
  * I2C EEPROM (CAT24WC16) for environment
  */
 #define CONFIG_HARD_I2C			/* I2c with hardware support */
@@ -247,10 +216,9 @@
 #define CFG_EEPROM_PAGE_WRITE_DELAY_MS	10   /* and takes up to 10 msec */
 #define CFG_EEPROM_PAGE_WRITE_ENABLE
 
-/*-----------------------------------------------------------------------
+/*
  * External Bus Controller (EBC) Setup
  */
-
 #define CAN_BA		0xF0000000	    /* CAN Base Address			*/
 
 /* Memory Bank 0 (Flash Bank 0, NOR-FLASH) initialization			*/
@@ -261,7 +229,7 @@
 #define CFG_EBC_PB2AP		0x010053C0  /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
 #define CFG_EBC_PB2CR		0xF0018000  /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit	*/
 
-/*-----------------------------------------------------------------------
+/*
  * FPGA stuff
  */
 #define CFG_FPGA_XC95XL		1	    /* using Xilinx XC95XL CPLD	     */
@@ -274,7 +242,7 @@
 #define CFG_FPGA_INIT		0x00010000  /* unused (ppc input)	     */
 #define CFG_FPGA_DONE		0x00008000  /* JTAG TDI->TDO pin (ppc input) */
 
-/*-----------------------------------------------------------------------
+/*
  * Definitions for initial stack pointer and data area (in data cache)
  */
 /* use on chip memory ( OCM ) for temperary stack until sdram is tested */
@@ -290,7 +258,7 @@
 #define CFG_GBL_DATA_OFFSET    (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
 #define CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET
 
-/*-----------------------------------------------------------------------
+/*
  * Definitions for GPIO setup (PPC405EP specific)
  *
  * GPIO0[0]	- External Bus Controller BLAST output
diff --git a/include/netdev.h b/include/netdev.h
new file mode 100644
index 0000000..8b181f7
--- /dev/null
+++ b/include/netdev.h
@@ -0,0 +1,110 @@
+/*
+ * (C) Copyright 2008
+ * Benjamin Warren, biggerbadderben@gmail.com
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * netdev.h - definitions an prototypes for network devices
+ */
+
+#ifndef _NETDEV_H_
+#define _NETDEV_H_
+
+/*
+ * Board and CPU-specific initialization functions
+ * board_eth_init() has highest priority.  cpu_eth_init() only
+ * gets called if board_eth_init() isn't instantiated or fails.
+ * Return values:
+ *      0: success
+ *     -1: failure
+ */
+
+int board_eth_init(bd_t *bis);
+int cpu_eth_init(bd_t *bis);
+
+/* Driver initialization prototypes */
+int bfin_EMAC_initialize(bd_t *bis);
+int dc21x4x_initialize(bd_t *bis);
+int e1000_initialize(bd_t *bis);
+int eepro100_initialize(bd_t *bis);
+int eth_3com_initialize (bd_t * bis);
+int greth_initialize(bd_t *bis);
+void gt6426x_eth_initialize(bd_t *bis);
+int inca_switch_initialize(bd_t *bis);
+int macb_eth_initialize(int id, void *regs, unsigned int phy_addr);
+int mcdmafec_initialize(bd_t *bis);
+int mcffec_initialize(bd_t *bis);
+int mpc512x_fec_initialize(bd_t *bis);
+int mpc5xxx_fec_initialize(bd_t *bis);
+int natsemi_initialize(bd_t *bis);
+int ns8382x_initialize(bd_t *bis);
+int pcnet_initialize(bd_t *bis);
+int plb2800_eth_initialize(bd_t *bis);
+int rtl8139_initialize(bd_t *bis);
+int rtl8169_initialize(bd_t *bis);
+int skge_initialize(bd_t *bis);
+int tsi108_eth_initialize(bd_t *bis);
+int uli526x_initialize(bd_t *bis);
+
+/* Boards with PCI network controllers can call this from their board_eth_init()
+ * function to initialize whatever's on board.
+ * Return value is total # of devices found */
+
+static inline int pci_eth_init(bd_t *bis)
+{
+	int num = 0;
+
+#ifdef CONFIG_PCI
+
+#ifdef CONFIG_EEPRO100
+	num += eepro100_initialize(bis);
+#endif
+#ifdef CONFIG_TULIP
+	num += dc21x4x_initialize(bis);
+#endif
+#ifdef CONFIG_E1000
+	num += e1000_initialize(bis);
+#endif
+#ifdef CONFIG_PCNET
+	num += pcnet_initialize(bis);
+#endif
+#ifdef CONFIG_NATSEMI
+	num += natsemi_initialize(bis);
+#endif
+#ifdef CONFIG_NS8382X
+	num += ns8382x_initialize(bis);
+#endif
+#if defined(CONFIG_RTL8139)
+	num += rtl8139_initialize(bis);
+#endif
+#if defined(CONFIG_RTL8169)
+	num += rtl8169_initialize(bis);
+#endif
+#if defined(CONFIG_ULI526)
+	num += uli526x_initialize(bis);
+#endif
+
+#endif  /* CONFIG_PCI */
+	return num;
+}
+
+#endif /* _NETDEV_H_ */
+
diff --git a/include/tsec.h b/include/tsec.h
new file mode 100644
index 0000000..2db4deb
--- /dev/null
+++ b/include/tsec.h
@@ -0,0 +1,639 @@
+/*
+ *  tsec.h
+ *
+ *  Driver for the Motorola Triple Speed Ethernet Controller
+ *
+ *  This software may be used and distributed according to the
+ *  terms of the GNU Public License, Version 2, incorporated
+ *  herein by reference.
+ *
+ * Copyright 2004, 2007 Freescale Semiconductor, Inc.
+ * (C) Copyright 2003, Motorola, Inc.
+ * maintained by Xianghua Xiao (x.xiao@motorola.com)
+ * author Andy Fleming
+ *
+ */
+
+#ifndef __TSEC_H
+#define __TSEC_H
+
+#include <net.h>
+#include <config.h>
+
+#ifndef CFG_TSEC1_OFFSET
+    #define CFG_TSEC1_OFFSET	(0x24000)
+#endif
+
+#define TSEC_SIZE	0x01000
+
+/* FIXME:  Should these be pushed back to 83xx and 85xx config files? */
+#if defined(CONFIG_MPC85xx) || defined(CONFIG_MPC86xx) \
+	|| defined(CONFIG_MPC83XX)
+    #define TSEC_BASE_ADDR	(CFG_IMMR + CFG_TSEC1_OFFSET)
+#endif
+
+#define STD_TSEC_INFO(num) \
+{			\
+	.regs = (tsec_t *)(TSEC_BASE_ADDR + ((num - 1) * TSEC_SIZE)), \
+	.miiregs = (tsec_t *)TSEC_BASE_ADDR, \
+	.devname = CONFIG_TSEC##num##_NAME, \
+	.phyaddr = TSEC##num##_PHY_ADDR, \
+	.flags = TSEC##num##_FLAGS \
+}
+
+#define SET_STD_TSEC_INFO(x, num) \
+{			\
+	x.regs = (tsec_t *)(TSEC_BASE_ADDR + ((num - 1) * TSEC_SIZE)); \
+	x.miiregs = (tsec_t *)TSEC_BASE_ADDR; \
+	x.devname = CONFIG_TSEC##num##_NAME; \
+	x.phyaddr = TSEC##num##_PHY_ADDR; \
+	x.flags = TSEC##num##_FLAGS;\
+}
+
+
+
+#define MAC_ADDR_LEN 6
+
+/* #define TSEC_TIMEOUT	1000000 */
+#define TSEC_TIMEOUT 1000
+#define TOUT_LOOP	1000000
+
+#define PHY_AUTONEGOTIATE_TIMEOUT	5000 /* in ms */
+
+/* TBI register addresses */
+#define TBI_CR			0x00
+#define TBI_SR			0x01
+#define TBI_ANA			0x04
+#define TBI_ANLPBPA		0x05
+#define TBI_ANEX		0x06
+#define TBI_TBICON		0x11
+
+/* TBI MDIO register bit fields*/
+#define TBICON_CLK_SELECT	0x0020
+#define TBIANA_ASYMMETRIC_PAUSE 0x0100
+#define TBIANA_SYMMETRIC_PAUSE  0x0080
+#define TBIANA_HALF_DUPLEX	0x0040
+#define TBIANA_FULL_DUPLEX	0x0020
+#define TBICR_PHY_RESET		0x8000
+#define TBICR_ANEG_ENABLE	0x1000
+#define TBICR_RESTART_ANEG	0x0200
+#define TBICR_FULL_DUPLEX	0x0100
+#define TBICR_SPEED1_SET	0x0040
+
+
+/* MAC register bits */
+#define MACCFG1_SOFT_RESET	0x80000000
+#define MACCFG1_RESET_RX_MC	0x00080000
+#define MACCFG1_RESET_TX_MC	0x00040000
+#define MACCFG1_RESET_RX_FUN	0x00020000
+#define	MACCFG1_RESET_TX_FUN	0x00010000
+#define MACCFG1_LOOPBACK	0x00000100
+#define MACCFG1_RX_FLOW		0x00000020
+#define MACCFG1_TX_FLOW		0x00000010
+#define MACCFG1_SYNCD_RX_EN	0x00000008
+#define MACCFG1_RX_EN		0x00000004
+#define MACCFG1_SYNCD_TX_EN	0x00000002
+#define MACCFG1_TX_EN		0x00000001
+
+#define MACCFG2_INIT_SETTINGS	0x00007205
+#define MACCFG2_FULL_DUPLEX	0x00000001
+#define MACCFG2_IF		0x00000300
+#define MACCFG2_GMII		0x00000200
+#define MACCFG2_MII		0x00000100
+
+#define ECNTRL_INIT_SETTINGS	0x00001000
+#define ECNTRL_TBI_MODE		0x00000020
+#define ECNTRL_R100		0x00000008
+#define ECNTRL_SGMII_MODE	0x00000002
+
+#define miim_end -2
+#define miim_read -1
+
+#ifndef CFG_TBIPA_VALUE
+    #define CFG_TBIPA_VALUE	0x1f
+#endif
+#define MIIMCFG_INIT_VALUE	0x00000003
+#define MIIMCFG_RESET		0x80000000
+
+#define MIIMIND_BUSY		0x00000001
+#define MIIMIND_NOTVALID	0x00000004
+
+#define MIIM_CONTROL		0x00
+#define MIIM_CONTROL_RESET	0x00009140
+#define MIIM_CONTROL_INIT	0x00001140
+#define MIIM_CONTROL_RESTART	0x00001340
+#define MIIM_ANEN		0x00001000
+
+#define MIIM_CR			0x00
+#define MIIM_CR_RST		0x00008000
+#define MIIM_CR_INIT		0x00001000
+
+#define MIIM_STATUS		0x1
+#define MIIM_STATUS_AN_DONE	0x00000020
+#define MIIM_STATUS_LINK	0x0004
+#define PHY_BMSR_AUTN_ABLE	0x0008
+#define PHY_BMSR_AUTN_COMP	0x0020
+
+#define MIIM_PHYIR1		0x2
+#define MIIM_PHYIR2		0x3
+
+#define MIIM_ANAR		0x4
+#define MIIM_ANAR_INIT		0x1e1
+
+#define MIIM_TBI_ANLPBPA	0x5
+#define MIIM_TBI_ANLPBPA_HALF	0x00000040
+#define MIIM_TBI_ANLPBPA_FULL	0x00000020
+
+#define MIIM_TBI_ANEX		0x6
+#define MIIM_TBI_ANEX_NP	0x00000004
+#define MIIM_TBI_ANEX_PRX	0x00000002
+
+#define MIIM_GBIT_CONTROL	0x9
+#define MIIM_GBIT_CONTROL_INIT	0xe00
+
+#define MIIM_EXT_PAGE_ACCESS	0x1f
+
+/* Broadcom BCM54xx -- taken from linux sungem_phy */
+#define MIIM_BCM54xx_AUXSTATUS			0x19
+#define MIIM_BCM54xx_AUXSTATUS_LINKMODE_MASK	0x0700
+#define MIIM_BCM54xx_AUXSTATUS_LINKMODE_SHIFT	8
+
+/* Cicada Auxiliary Control/Status Register */
+#define MIIM_CIS8201_AUX_CONSTAT	0x1c
+#define MIIM_CIS8201_AUXCONSTAT_INIT	0x0004
+#define MIIM_CIS8201_AUXCONSTAT_DUPLEX	0x0020
+#define MIIM_CIS8201_AUXCONSTAT_SPEED	0x0018
+#define MIIM_CIS8201_AUXCONSTAT_GBIT	0x0010
+#define MIIM_CIS8201_AUXCONSTAT_100	0x0008
+
+/* Cicada Extended Control Register 1 */
+#define MIIM_CIS8201_EXT_CON1		0x17
+#define MIIM_CIS8201_EXTCON1_INIT	0x0000
+
+/* Cicada 8204 Extended PHY Control Register 1 */
+#define MIIM_CIS8204_EPHY_CON		0x17
+#define MIIM_CIS8204_EPHYCON_INIT	0x0006
+#define MIIM_CIS8204_EPHYCON_RGMII	0x1100
+
+/* Cicada 8204 Serial LED Control Register */
+#define MIIM_CIS8204_SLED_CON		0x1b
+#define MIIM_CIS8204_SLEDCON_INIT	0x1115
+
+#define MIIM_GBIT_CON		0x09
+#define MIIM_GBIT_CON_ADVERT	0x0e00
+
+/* Entry for Vitesse VSC8244 regs starts here */
+/* Vitesse VSC8244 Auxiliary Control/Status Register */
+#define MIIM_VSC8244_AUX_CONSTAT	0x1c
+#define MIIM_VSC8244_AUXCONSTAT_INIT	0x0000
+#define MIIM_VSC8244_AUXCONSTAT_DUPLEX	0x0020
+#define MIIM_VSC8244_AUXCONSTAT_SPEED	0x0018
+#define MIIM_VSC8244_AUXCONSTAT_GBIT	0x0010
+#define MIIM_VSC8244_AUXCONSTAT_100	0x0008
+#define MIIM_CONTROL_INIT_LOOPBACK	0x4000
+
+/* Vitesse VSC8244 Extended PHY Control Register 1 */
+#define MIIM_VSC8244_EPHY_CON		0x17
+#define MIIM_VSC8244_EPHYCON_INIT	0x0006
+
+/* Vitesse VSC8244 Serial LED Control Register */
+#define MIIM_VSC8244_LED_CON		0x1b
+#define MIIM_VSC8244_LEDCON_INIT	0xF011
+
+/* Entry for Vitesse VSC8601 regs starts here (Not complete) */
+/* Vitesse VSC8601 Extended PHY Control Register 1 */
+#define MIIM_VSC8601_EPHY_CON		0x17
+#define MIIM_VSC8601_EPHY_CON_INIT_SKEW	0x1120
+#define MIIM_VSC8601_SKEW_CTRL		0x1c
+
+/* 88E1011 PHY Status Register */
+#define MIIM_88E1011_PHY_STATUS		0x11
+#define MIIM_88E1011_PHYSTAT_SPEED	0xc000
+#define MIIM_88E1011_PHYSTAT_GBIT	0x8000
+#define MIIM_88E1011_PHYSTAT_100	0x4000
+#define MIIM_88E1011_PHYSTAT_DUPLEX	0x2000
+#define MIIM_88E1011_PHYSTAT_SPDDONE	0x0800
+#define MIIM_88E1011_PHYSTAT_LINK	0x0400
+
+#define MIIM_88E1011_PHY_SCR		0x10
+#define MIIM_88E1011_PHY_MDI_X_AUTO	0x0060
+
+/* 88E1111 PHY LED Control Register */
+#define MIIM_88E1111_PHY_LED_CONTROL	24
+#define MIIM_88E1111_PHY_LED_DIRECT	0x4100
+#define MIIM_88E1111_PHY_LED_COMBINE	0x411C
+
+/* 88E1121 PHY LED Control Register */
+#define MIIM_88E1121_PHY_LED_CTRL	16
+#define MIIM_88E1121_PHY_LED_PAGE	3
+#define MIIM_88E1121_PHY_LED_DEF	0x0030
+
+#define MIIM_88E1121_PHY_PAGE		22
+
+/* 88E1145 Extended PHY Specific Control Register */
+#define MIIM_88E1145_PHY_EXT_CR 20
+#define MIIM_M88E1145_RGMII_RX_DELAY	0x0080
+#define MIIM_M88E1145_RGMII_TX_DELAY	0x0002
+
+#define MIIM_88E1145_PHY_PAGE	29
+#define MIIM_88E1145_PHY_CAL_OV 30
+
+/* RTL8211B PHY Status Register */
+#define MIIM_RTL8211B_PHY_STATUS	0x11
+#define MIIM_RTL8211B_PHYSTAT_SPEED	0xc000
+#define MIIM_RTL8211B_PHYSTAT_GBIT	0x8000
+#define MIIM_RTL8211B_PHYSTAT_100	0x4000
+#define MIIM_RTL8211B_PHYSTAT_DUPLEX	0x2000
+#define MIIM_RTL8211B_PHYSTAT_SPDDONE	0x0800
+#define MIIM_RTL8211B_PHYSTAT_LINK	0x0400
+
+/* DM9161 Control register values */
+#define MIIM_DM9161_CR_STOP	0x0400
+#define MIIM_DM9161_CR_RSTAN	0x1200
+
+#define MIIM_DM9161_SCR		0x10
+#define MIIM_DM9161_SCR_INIT	0x0610
+
+/* DM9161 Specified Configuration and Status Register */
+#define MIIM_DM9161_SCSR	0x11
+#define MIIM_DM9161_SCSR_100F	0x8000
+#define MIIM_DM9161_SCSR_100H	0x4000
+#define MIIM_DM9161_SCSR_10F	0x2000
+#define MIIM_DM9161_SCSR_10H	0x1000
+
+/* DM9161 10BT Configuration/Status */
+#define MIIM_DM9161_10BTCSR	0x12
+#define MIIM_DM9161_10BTCSR_INIT	0x7800
+
+/* LXT971 Status 2 registers */
+#define MIIM_LXT971_SR2		     0x11  /* Status Register 2  */
+#define MIIM_LXT971_SR2_SPEED_MASK 0x4200
+#define MIIM_LXT971_SR2_10HDX	   0x0000  /*  10 Mbit half duplex selected */
+#define MIIM_LXT971_SR2_10FDX	   0x0200  /*  10 Mbit full duplex selected */
+#define MIIM_LXT971_SR2_100HDX	   0x4000  /* 100 Mbit half duplex selected */
+#define MIIM_LXT971_SR2_100FDX	   0x4200  /* 100 Mbit full duplex selected */
+
+/* DP83865 Control register values */
+#define MIIM_DP83865_CR_INIT	0x9200
+
+/* DP83865 Link and Auto-Neg Status Register */
+#define MIIM_DP83865_LANR	0x11
+#define MIIM_DP83865_SPD_MASK	0x0018
+#define MIIM_DP83865_SPD_1000	0x0010
+#define MIIM_DP83865_SPD_100	0x0008
+#define MIIM_DP83865_DPX_FULL	0x0002
+
+#define MIIM_READ_COMMAND	0x00000001
+
+#define MRBLR_INIT_SETTINGS	PKTSIZE_ALIGN
+
+#define MINFLR_INIT_SETTINGS	0x00000040
+
+#define DMACTRL_INIT_SETTINGS	0x000000c3
+#define DMACTRL_GRS		0x00000010
+#define DMACTRL_GTS		0x00000008
+
+#define TSTAT_CLEAR_THALT	0x80000000
+#define RSTAT_CLEAR_RHALT	0x00800000
+
+
+#define IEVENT_INIT_CLEAR	0xffffffff
+#define IEVENT_BABR		0x80000000
+#define IEVENT_RXC		0x40000000
+#define IEVENT_BSY		0x20000000
+#define IEVENT_EBERR		0x10000000
+#define IEVENT_MSRO		0x04000000
+#define IEVENT_GTSC		0x02000000
+#define IEVENT_BABT		0x01000000
+#define IEVENT_TXC		0x00800000
+#define IEVENT_TXE		0x00400000
+#define IEVENT_TXB		0x00200000
+#define IEVENT_TXF		0x00100000
+#define IEVENT_IE		0x00080000
+#define IEVENT_LC		0x00040000
+#define IEVENT_CRL		0x00020000
+#define IEVENT_XFUN		0x00010000
+#define IEVENT_RXB0		0x00008000
+#define IEVENT_GRSC		0x00000100
+#define IEVENT_RXF0		0x00000080
+
+#define IMASK_INIT_CLEAR	0x00000000
+#define IMASK_TXEEN		0x00400000
+#define IMASK_TXBEN		0x00200000
+#define IMASK_TXFEN		0x00100000
+#define IMASK_RXFEN0		0x00000080
+
+
+/* Default Attribute fields */
+#define ATTR_INIT_SETTINGS     0x000000c0
+#define ATTRELI_INIT_SETTINGS  0x00000000
+
+
+/* TxBD status field bits */
+#define TXBD_READY		0x8000
+#define TXBD_PADCRC		0x4000
+#define TXBD_WRAP		0x2000
+#define TXBD_INTERRUPT		0x1000
+#define TXBD_LAST		0x0800
+#define TXBD_CRC		0x0400
+#define TXBD_DEF		0x0200
+#define TXBD_HUGEFRAME		0x0080
+#define TXBD_LATECOLLISION	0x0080
+#define TXBD_RETRYLIMIT		0x0040
+#define	TXBD_RETRYCOUNTMASK	0x003c
+#define TXBD_UNDERRUN		0x0002
+#define TXBD_STATS		0x03ff
+
+/* RxBD status field bits */
+#define RXBD_EMPTY		0x8000
+#define RXBD_RO1		0x4000
+#define RXBD_WRAP		0x2000
+#define RXBD_INTERRUPT		0x1000
+#define RXBD_LAST		0x0800
+#define RXBD_FIRST		0x0400
+#define RXBD_MISS		0x0100
+#define RXBD_BROADCAST		0x0080
+#define RXBD_MULTICAST		0x0040
+#define RXBD_LARGE		0x0020
+#define RXBD_NONOCTET		0x0010
+#define RXBD_SHORT		0x0008
+#define RXBD_CRCERR		0x0004
+#define RXBD_OVERRUN		0x0002
+#define RXBD_TRUNCATED		0x0001
+#define RXBD_STATS		0x003f
+
+typedef struct txbd8
+{
+	ushort	     status;	     /* Status Fields */
+	ushort	     length;	     /* Buffer length */
+	uint	     bufPtr;	     /* Buffer Pointer */
+} txbd8_t;
+
+typedef struct rxbd8
+{
+	ushort	     status;	     /* Status Fields */
+	ushort	     length;	     /* Buffer Length */
+	uint	     bufPtr;	     /* Buffer Pointer */
+} rxbd8_t;
+
+typedef struct rmon_mib
+{
+	/* Transmit and Receive Counters */
+	uint	tr64;		/* Transmit and Receive 64-byte Frame Counter */
+	uint	tr127;		/* Transmit and Receive 65-127 byte Frame Counter */
+	uint	tr255;		/* Transmit and Receive 128-255 byte Frame Counter */
+	uint	tr511;		/* Transmit and Receive 256-511 byte Frame Counter */
+	uint	tr1k;		/* Transmit and Receive 512-1023 byte Frame Counter */
+	uint	trmax;		/* Transmit and Receive 1024-1518 byte Frame Counter */
+	uint	trmgv;		/* Transmit and Receive 1519-1522 byte Good VLAN Frame */
+	/* Receive Counters */
+	uint	rbyt;		/* Receive Byte Counter */
+	uint	rpkt;		/* Receive Packet Counter */
+	uint	rfcs;		/* Receive FCS Error Counter */
+	uint	rmca;		/* Receive Multicast Packet (Counter) */
+	uint	rbca;		/* Receive Broadcast Packet */
+	uint	rxcf;		/* Receive Control Frame Packet */
+	uint	rxpf;		/* Receive Pause Frame Packet */
+	uint	rxuo;		/* Receive Unknown OP Code */
+	uint	raln;		/* Receive Alignment Error */
+	uint	rflr;		/* Receive Frame Length Error */
+	uint	rcde;		/* Receive Code Error */
+	uint	rcse;		/* Receive Carrier Sense Error */
+	uint	rund;		/* Receive Undersize Packet */
+	uint	rovr;		/* Receive Oversize Packet */
+	uint	rfrg;		/* Receive Fragments */
+	uint	rjbr;		/* Receive Jabber */
+	uint	rdrp;		/* Receive Drop */
+	/* Transmit Counters */
+	uint	tbyt;		/* Transmit Byte Counter */
+	uint	tpkt;		/* Transmit Packet */
+	uint	tmca;		/* Transmit Multicast Packet */
+	uint	tbca;		/* Transmit Broadcast Packet */
+	uint	txpf;		/* Transmit Pause Control Frame */
+	uint	tdfr;		/* Transmit Deferral Packet */
+	uint	tedf;		/* Transmit Excessive Deferral Packet */
+	uint	tscl;		/* Transmit Single Collision Packet */
+	/* (0x2_n700) */
+	uint	tmcl;		/* Transmit Multiple Collision Packet */
+	uint	tlcl;		/* Transmit Late Collision Packet */
+	uint	txcl;		/* Transmit Excessive Collision Packet */
+	uint	tncl;		/* Transmit Total Collision */
+
+	uint	res2;
+
+	uint	tdrp;		/* Transmit Drop Frame */
+	uint	tjbr;		/* Transmit Jabber Frame */
+	uint	tfcs;		/* Transmit FCS Error */
+	uint	txcf;		/* Transmit Control Frame */
+	uint	tovr;		/* Transmit Oversize Frame */
+	uint	tund;		/* Transmit Undersize Frame */
+	uint	tfrg;		/* Transmit Fragments Frame */
+	/* General Registers */
+	uint	car1;		/* Carry Register One */
+	uint	car2;		/* Carry Register Two */
+	uint	cam1;		/* Carry Register One Mask */
+	uint	cam2;		/* Carry Register Two Mask */
+} rmon_mib_t;
+
+typedef struct tsec_hash_regs
+{
+	uint	iaddr0;		/* Individual Address Register 0 */
+	uint	iaddr1;		/* Individual Address Register 1 */
+	uint	iaddr2;		/* Individual Address Register 2 */
+	uint	iaddr3;		/* Individual Address Register 3 */
+	uint	iaddr4;		/* Individual Address Register 4 */
+	uint	iaddr5;		/* Individual Address Register 5 */
+	uint	iaddr6;		/* Individual Address Register 6 */
+	uint	iaddr7;		/* Individual Address Register 7 */
+	uint	res1[24];
+	uint	gaddr0;		/* Group Address Register 0 */
+	uint	gaddr1;		/* Group Address Register 1 */
+	uint	gaddr2;		/* Group Address Register 2 */
+	uint	gaddr3;		/* Group Address Register 3 */
+	uint	gaddr4;		/* Group Address Register 4 */
+	uint	gaddr5;		/* Group Address Register 5 */
+	uint	gaddr6;		/* Group Address Register 6 */
+	uint	gaddr7;		/* Group Address Register 7 */
+	uint	res2[24];
+} tsec_hash_t;
+
+typedef struct tsec
+{
+	/* General Control and Status Registers (0x2_n000) */
+	uint	res000[4];
+
+	uint	ievent;		/* Interrupt Event */
+	uint	imask;		/* Interrupt Mask */
+	uint	edis;		/* Error Disabled */
+	uint	res01c;
+	uint	ecntrl;		/* Ethernet Control */
+	uint	minflr;		/* Minimum Frame Length */
+	uint	ptv;		/* Pause Time Value */
+	uint	dmactrl;	/* DMA Control */
+	uint	tbipa;		/* TBI PHY Address */
+
+	uint	res034[3];
+	uint	res040[48];
+
+	/* Transmit Control and Status Registers (0x2_n100) */
+	uint	tctrl;		/* Transmit Control */
+	uint	tstat;		/* Transmit Status */
+	uint	res108;
+	uint	tbdlen;		/* Tx BD Data Length */
+	uint	res110[5];
+	uint	ctbptr;		/* Current TxBD Pointer */
+	uint	res128[23];
+	uint	tbptr;		/* TxBD Pointer */
+	uint	res188[30];
+	/* (0x2_n200) */
+	uint	res200;
+	uint	tbase;		/* TxBD Base Address */
+	uint	res208[42];
+	uint	ostbd;		/* Out of Sequence TxBD */
+	uint	ostbdp;		/* Out of Sequence Tx Data Buffer Pointer */
+	uint	res2b8[18];
+
+	/* Receive Control and Status Registers (0x2_n300) */
+	uint	rctrl;		/* Receive Control */
+	uint	rstat;		/* Receive Status */
+	uint	res308;
+	uint	rbdlen;		/* RxBD Data Length */
+	uint	res310[4];
+	uint	res320;
+	uint	crbptr;	/* Current Receive Buffer Pointer */
+	uint	res328[6];
+	uint	mrblr;	/* Maximum Receive Buffer Length */
+	uint	res344[16];
+	uint	rbptr;	/* RxBD Pointer */
+	uint	res388[30];
+	/* (0x2_n400) */
+	uint	res400;
+	uint	rbase;	/* RxBD Base Address */
+	uint	res408[62];
+
+	/* MAC Registers (0x2_n500) */
+	uint	maccfg1;	/* MAC Configuration #1 */
+	uint	maccfg2;	/* MAC Configuration #2 */
+	uint	ipgifg;		/* Inter Packet Gap/Inter Frame Gap */
+	uint	hafdup;		/* Half-duplex */
+	uint	maxfrm;		/* Maximum Frame */
+	uint	res514;
+	uint	res518;
+
+	uint	res51c;
+
+	uint	miimcfg;	/* MII Management: Configuration */
+	uint	miimcom;	/* MII Management: Command */
+	uint	miimadd;	/* MII Management: Address */
+	uint	miimcon;	/* MII Management: Control */
+	uint	miimstat;	/* MII Management: Status */
+	uint	miimind;	/* MII Management: Indicators */
+
+	uint	res538;
+
+	uint	ifstat;		/* Interface Status */
+	uint	macstnaddr1;	/* Station Address, part 1 */
+	uint	macstnaddr2;	/* Station Address, part 2 */
+	uint	res548[46];
+
+	/* (0x2_n600) */
+	uint	res600[32];
+
+	/* RMON MIB Registers (0x2_n680-0x2_n73c) */
+	rmon_mib_t	rmon;
+	uint	res740[48];
+
+	/* Hash Function Registers (0x2_n800) */
+	tsec_hash_t	hash;
+
+	uint	res900[128];
+
+	/* Pattern Registers (0x2_nb00) */
+	uint	resb00[62];
+	uint	attr;	   /* Default Attribute Register */
+	uint	attreli;	   /* Default Attribute Extract Length and Index */
+
+	/* TSEC Future Expansion Space (0x2_nc00-0x2_nffc) */
+	uint	resc00[256];
+} tsec_t;
+
+#define TSEC_GIGABIT (1)
+
+/* This flag currently only has
+ * meaning if we're using the eTSEC */
+#define TSEC_REDUCED	(1 << 1)
+
+#define TSEC_SGMII	(1 << 2)
+
+struct tsec_private {
+	volatile tsec_t *regs;
+	volatile tsec_t *phyregs;
+	struct phy_info *phyinfo;
+	uint phyaddr;
+	u32 flags;
+	uint link;
+	uint duplexity;
+	uint speed;
+};
+
+
+/*
+ * struct phy_cmd:  A command for reading or writing a PHY register
+ *
+ * mii_reg:  The register to read or write
+ *
+ * mii_data:  For writes, the value to put in the register.
+ *	A value of -1 indicates this is a read.
+ *
+ * funct: A function pointer which is invoked for each command.
+ *	For reads, this function will be passed the value read
+ *	from the PHY, and process it.
+ *	For writes, the result of this function will be written
+ *	to the PHY register
+ */
+struct phy_cmd {
+	uint mii_reg;
+	uint mii_data;
+	uint (*funct) (uint mii_reg, struct tsec_private * priv);
+};
+
+/* struct phy_info: a structure which defines attributes for a PHY
+ *
+ * id will contain a number which represents the PHY.  During
+ * startup, the driver will poll the PHY to find out what its
+ * UID--as defined by registers 2 and 3--is.  The 32-bit result
+ * gotten from the PHY will be shifted right by "shift" bits to
+ * discard any bits which may change based on revision numbers
+ * unimportant to functionality
+ *
+ * The struct phy_cmd entries represent pointers to an arrays of
+ * commands which tell the driver what to do to the PHY.
+ */
+struct phy_info {
+	uint id;
+	char *name;
+	uint shift;
+	/* Called to configure the PHY, and modify the controller
+	 * based on the results */
+	struct phy_cmd *config;
+
+	/* Called when starting up the controller */
+	struct phy_cmd *startup;
+
+	/* Called when bringing down the controller */
+	struct phy_cmd *shutdown;
+};
+
+struct tsec_info_struct {
+	tsec_t *regs;
+	tsec_t *miiregs;
+	char *devname;
+	unsigned int phyaddr;
+	u32 flags;
+};
+
+int tsec_initialize(bd_t * bis, struct tsec_info_struct *tsec_info);
+int tsec_standard_init(bd_t *bis);
+int tsec_eth_init(bd_t *bis, struct tsec_info_struct *tsec_info, int num);
+
+#endif /* __TSEC_H */