powerpc: mpc8xx: remove hermes board support

This board sprinkles #ifdef(CONFIG_HERMES) over various global files
such as include/common.h, common/board_r.c, common/cmd_bdinfo.c.
Let's zap such an ill-behaved board.

It has not been converted to generic board yet and mpc8xx is old
enough.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>
Acked-by: Wolfgang Denk <wd@denx.de>

3 files changed, 0 insertions, 348 deletions

diff --git a/include/common.h b/include/common.h
index 94c354b..46f07fe 100644
--- a/include/common.h
+++ b/include/common.h
@@ -445,11 +445,6 @@ extern ssize_t spi_read	 (uchar *, int, uchar *, int);
 extern ssize_t spi_write (uchar *, int, uchar *, int);
 #endif
 
-#ifdef CONFIG_HERMES
-/* $(BOARD)/hermes.c */
-void hermes_start_lxt980 (int speed);
-#endif
-
 #ifdef CONFIG_EVB64260
 void  evb64260_init(void);
 void  debug_led(int, int);
diff --git a/include/commproc.h b/include/commproc.h
index d78ab00..6875c4c 100644
--- a/include/commproc.h
+++ b/include/commproc.h
@@ -535,34 +535,6 @@ typedef struct scc_enet {
 #define SICR_ENET_CLKRT	((uint)0x00002600)
 #endif	/* CONFIG_FPS850L, CONFIG_FPS860L */
 
-/*** HERMES-PRO ******************************************************/
-
-/* The HERMES-PRO uses the FEC on a MPC860T for Ethernet */
-
-#ifdef CONFIG_HERMES
-
-#define	FEC_ENET	/* use FEC for EThernet */
-#undef	SCC_ENET
-
-
-#define PD_MII_TXD1	((ushort)0x1000)	/* PD  3 */
-#define PD_MII_TXD2	((ushort)0x0800)	/* PD  4 */
-#define PD_MII_TXD3	((ushort)0x0400)	/* PD  5 */
-#define PD_MII_RX_DV	((ushort)0x0200)	/* PD  6 */
-#define PD_MII_RX_ERR	((ushort)0x0100)	/* PD  7 */
-#define PD_MII_RX_CLK	((ushort)0x0080)	/* PD  8 */
-#define PD_MII_TXD0	((ushort)0x0040)	/* PD  9 */
-#define PD_MII_RXD0	((ushort)0x0020)	/* PD 10 */
-#define PD_MII_TX_ERR	((ushort)0x0010)	/* PD 11 */
-#define PD_MII_MDC	((ushort)0x0008)	/* PD 12 */
-#define PD_MII_RXD1	((ushort)0x0004)	/* PD 13 */
-#define PD_MII_RXD2	((ushort)0x0002)	/* PD 14 */
-#define PD_MII_RXD3	((ushort)0x0001)	/* PD 15 */
-
-#define PD_MII_MASK	((ushort)0x1FFF)	/* PD 3...15 */
-
-#endif	/* CONFIG_HERMES */
-
 /***  IP860  **********************************************************/
 
 #if defined(CONFIG_IP860)
diff --git a/include/configs/hermes.h b/include/configs/hermes.h
deleted file mode 100644
index 736ffb61..0000000
--- a/include/configs/hermes.h
+++ /dev/null
@@ -1,315 +0,0 @@
-/*
- * (C) Copyright 2000
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-/*
- * board/config.h - configuration options, board specific
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_MPC860		1	/* This is a MPC860T CPU	*/
-#define CONFIG_HERMES		1	/* ...on a HERMES-PRO board	*/
-
-#define	CONFIG_SYS_TEXT_BASE	0xFE000000
-
-#define	CONFIG_8xx_CONS_SMC1	1	/* Console is on SMC1		*/
-#undef	CONFIG_8xx_CONS_SMC2
-#undef	CONFIG_8xx_CONS_NONE
-#define CONFIG_BAUDRATE		9600
-#if 0
-#define CONFIG_BOOTDELAY	-1	/* autoboot disabled		*/
-#else
-#define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds	*/
-#endif
-
-#define	CONFIG_CLOCKS_IN_MHZ	1	/* clocks passsed to Linux in MHz */
-
-#define CONFIG_BOARD_TYPES	1	/* support board types		*/
-
-#define	CONFIG_SHOW_BOOT_PROGRESS 1	/* Show boot progress on LEDs	*/
-
-#undef	CONFIG_BOOTARGS
-#define CONFIG_BOOTCOMMAND							\
-	"bootp; "								\
-	"setenv bootargs root=/dev/nfs rw nfsroot=${serverip}:${rootpath} "	\
-	"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off; "	\
-	"bootm"
-
-#define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
-#undef	CONFIG_SYS_LOADS_BAUD_CHANGE		/* don't allow baudrate change	*/
-
-#undef	CONFIG_WATCHDOG			/* watchdog disabled		*/
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_SUBNETMASK
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_BOOTP_BOOTPATH
-
-
-/*
- * Miscellaneous configurable options
- */
-#define	CONFIG_SYS_LONGHELP			/* undef to save memory		*/
-#if defined(CONFIG_CMD_KGDB)
-#define	CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size	*/
-#else
-#define	CONFIG_SYS_CBSIZE	256		/* Console I/O Buffer Size	*/
-#endif
-#define	CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define	CONFIG_SYS_MAXARGS	16		/* max number of command args	*/
-#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/
-
-#define CONFIG_SYS_MEMTEST_START	0x00100000	/* memtest works on	*/
-#define CONFIG_SYS_MEMTEST_END		0x00F00000	/* 1 ... 15MB in DRAM	*/
-
-#define	CONFIG_SYS_LOAD_ADDR		0x00100000	/* default load address	*/
-
-#define	CONFIG_SYS_PIO_MODE		0	/* IDE interface in PIO Mode 0	*/
-
-#define	CONFIG_SYS_ALLOC_DPRAM		1	/* use allocation routines	*/
-/*
- * Low Level Configuration Settings
- * (address mappings, register initial values, etc.)
- * You should know what you are doing if you make changes here.
- */
-/*-----------------------------------------------------------------------
- * Internal Memory Mapped Register
- */
-#define CONFIG_SYS_IMMR		0xFF000000	/* Non-Standard value!	*/
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in DPRAM)
- */
-#define CONFIG_SYS_INIT_RAM_ADDR	CONFIG_SYS_IMMR
-#define	CONFIG_SYS_INIT_RAM_SIZE	0x2F00	/* Size of used area in DPRAM	*/
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define	CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- */
-#define	CONFIG_SYS_SDRAM_BASE		0x00000000
-#define CONFIG_SYS_FLASH_BASE		0xFE000000
-#ifdef	DEBUG
-#define	CONFIG_SYS_MONITOR_LEN		(256 << 10)	/* Reserve 256 kB for Monitor	*/
-#else
-#define	CONFIG_SYS_MONITOR_LEN		(128 << 10)	/* Reserve 128 kB for Monitor	*/
-#endif
-#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_FLASH_BASE
-#define	CONFIG_SYS_MALLOC_LEN		(128 << 10)	/* Reserve 128 kB for malloc()	*/
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define	CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux	*/
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max number of memory banks		*/
-#define CONFIG_SYS_MAX_FLASH_SECT	124	/* max number of sectors on one chip	*/
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
-#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/
-
-#define	CONFIG_ENV_IS_IN_FLASH	1
-#define	CONFIG_ENV_OFFSET		0x4000	/*   Offset   of Environment Sector	*/
-#define	CONFIG_ENV_SIZE		0x2000	/* Total Size of Environment Sector	*/
-/*-----------------------------------------------------------------------
- * Cache Configuration
- */
-#define CONFIG_SYS_CACHELINE_SIZE	16	/* For all MPC8xx CPUs			*/
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CACHELINE_SHIFT	4	/* log base 2 of the above value	*/
-#endif
-
-/*-----------------------------------------------------------------------
- * SYPCR - System Protection Control				11-9
- * SYPCR can only be written once after reset!
- *-----------------------------------------------------------------------
- * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
- * +0x0004
- */
-#if defined(CONFIG_WATCHDOG)
-#define CONFIG_SYS_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
-			 SYPCR_SWE  | SYPCR_SWRI| SYPCR_SWP)
-#else
-#define CONFIG_SYS_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
-#endif
-
-/*-----------------------------------------------------------------------
- * SIUMCR - SIU Module Configuration				11-6
- *-----------------------------------------------------------------------
- * +0x0000 => 0x000000C0
- */
-#define CONFIG_SYS_SIUMCR	0
-
-/*-----------------------------------------------------------------------
- * TBSCR - Time Base Status and Control				11-26
- *-----------------------------------------------------------------------
- * Clear Reference Interrupt Status, Timebase freezing enabled
- * +0x0200 => 0x00C2
- */
-#define CONFIG_SYS_TBSCR	(TBSCR_REFA | TBSCR_REFB | TBSCR_TBF)
-
-/*-----------------------------------------------------------------------
- * PISCR - Periodic Interrupt Status and Control		11-31
- *-----------------------------------------------------------------------
- * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
- * +0x0240 => 0x0082
- */
-#define CONFIG_SYS_PISCR	(PISCR_PS | PISCR_PITF)
-
-/*-----------------------------------------------------------------------
- * PLPRCR - PLL, Low-Power, and Reset Control Register		15-30
- *-----------------------------------------------------------------------
- * Reset PLL lock status sticky bit, timer expired status bit and timer
- * interrupt status bit, set PLL multiplication factor !
- */
-/* +0x0286 => 0x00B0D0C0 */
-#define CONFIG_SYS_PLPRCR							\
-		(	(11 << PLPRCR_MF_SHIFT) |			\
-			PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST |	\
-			/*PLPRCR_CSRC|*/ PLPRCR_LPM_NORMAL |		\
-			PLPRCR_CSR   | PLPRCR_LOLRE /*|PLPRCR_FIOPD*/	\
-		)
-
-/*-----------------------------------------------------------------------
- * SCCR - System Clock and reset Control Register		15-27
- *-----------------------------------------------------------------------
- * Set clock output, timebase and RTC source and divider,
- * power management and some other internal clocks
- */
-#define SCCR_MASK	SCCR_EBDF11
-/* +0x0282 => 0x03800000 */
-#define CONFIG_SYS_SCCR	(SCCR_COM00	|   SCCR_TBS	  |	\
-			 SCCR_RTDIV	|   SCCR_RTSEL	  |	\
-			 /*SCCR_CRQEN|*/  /*SCCR_PRQEN|*/	\
-			 SCCR_EBDF00	|   SCCR_DFSYNC00 |	\
-			 SCCR_DFBRG00	|   SCCR_DFNL000  |	\
-			 SCCR_DFNH000)
-
-/*-----------------------------------------------------------------------
- * RTCSC - Real-Time Clock Status and Control Register		11-27
- *-----------------------------------------------------------------------
- */
-/* +0x0220 => 0x00C3 */
-#define CONFIG_SYS_RTCSC	(RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE)
-
-
-/*-----------------------------------------------------------------------
- * RCCR - RISC Controller Configuration Register		19-4
- *-----------------------------------------------------------------------
- */
-/* +0x09C4 => TIMEP=1 */
-#define CONFIG_SYS_RCCR 0x0100
-
-/*-----------------------------------------------------------------------
- * RMDS - RISC Microcode Development Support Control Register
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SYS_RMDS 0
-
-/*-----------------------------------------------------------------------
- *
- *-----------------------------------------------------------------------
- *
- */
-#define CONFIG_SYS_DER	0
-
-/*
- * Init Memory Controller:
- *
- * BR0 and OR0 (FLASH)
- */
-
-#define FLASH_BASE0_PRELIM	0xFE000000	/* FLASH bank #0	*/
-
-/* used to re-map FLASH
- * restrict access enough to keep SRAM working (if any)
- * but not too much to meddle with FLASH accesses
- */
-/* allow for max 4 MB of Flash */
-#define CONFIG_SYS_REMAP_OR_AM		0xFFC00000	/* OR addr mask */
-#define CONFIG_SYS_PRELIM_OR_AM	0xFFC00000	/* OR addr mask */
-
-/* FLASH timing: ACS = 11, TRLX = 1, CSNT = 1, SCY = 5, EHTR = 0	*/
-#define CONFIG_SYS_OR_TIMING_FLASH	( OR_CSNT_SAM | /*OR_ACS_DIV4 |*/ OR_BI | \
-				 OR_SCY_5_CLK | OR_TRLX)
-
-#define CONFIG_SYS_OR0_REMAP	(CONFIG_SYS_REMAP_OR_AM  | CONFIG_SYS_OR_TIMING_FLASH)
-#define CONFIG_SYS_OR0_PRELIM	(CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)
-/* 8 bit, bank valid */
-#define CONFIG_SYS_BR0_PRELIM	((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_PS_8 | BR_V )
-
-/*
- * BR1/OR1 - SDRAM
- *
- * Multiplexed addresses, GPL5 output to GPL5_A (don't care)
- */
-#define SDRAM_BASE_PRELIM	0x00000000	/* SDRAM bank */
-#define SDRAM_PRELIM_OR_AM	0xF8000000	/* map max. 128 MB */
-#define SDRAM_TIMING		0x00000A00	/* SDRAM-Timing */
-
-#define SDRAM_MAX_SIZE		0x04000000	/* max 64 MB SDRAM */
-
-#define CONFIG_SYS_OR1_PRELIM	(SDRAM_PRELIM_OR_AM | SDRAM_TIMING )
-#define CONFIG_SYS_BR1_PRELIM	((SDRAM_BASE_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
-
-/*
- * BR2/OR2 - HPRO2: PEB2256   @ 0xE0000000, 8 Bit wide
- */
-#define HPRO2_BASE		0xE0000000
-#define HPRO2_OR_AM		0xFFFF8000
-#define HPRO2_TIMING		0x00000934
-
-#define CONFIG_SYS_OR2 (HPRO2_OR_AM | HPRO2_TIMING)
-#define CONFIG_SYS_BR2	((HPRO2_BASE & BR_BA_MSK) | BR_PS_8 | BR_V )
-
-/*
- * BR3/OR3: not used
- * BR4/OR4: not used
- * BR5/OR5: not used
- * BR6/OR6: not used
- * BR7/OR7: not used
- */
-
-/*
- * MAMR settings for SDRAM
- */
-
-/* periodic timer for refresh */
-#define CONFIG_SYS_MAMR_PTA	97		/* start with divider for 100 MHz	*/
-
-/* 8 column SDRAM */
-#define CONFIG_SYS_MAMR_8COL	((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT)  | MAMR_PTAE	    |	\
-			 MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A11 |	\
-			 MAMR_RLFA_1X	 | MAMR_WLFA_1X	   | MAMR_TLFA_4X)
-/* 9 column SDRAM */
-#define CONFIG_SYS_MAMR_9COL	((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT)  | MAMR_PTAE	    |	\
-			 MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 |	\
-			 MAMR_RLFA_1X	 | MAMR_WLFA_1X	   | MAMR_TLFA_4X)
-#endif	/* __CONFIG_H */