Merge branch 'master' of git://git.denx.de/u-boot-arm

5 files changed, 107 insertions, 15 deletions

diff --git a/drivers/block/dwc_ahsata.c b/drivers/block/dwc_ahsata.c
index 15d65d7..29f478b 100644
--- a/drivers/block/dwc_ahsata.c
+++ b/drivers/block/dwc_ahsata.c
@@ -864,6 +864,23 @@ u32 ata_low_level_rw_lba28(int dev, u32 blknr, lbaint_t blkcnt,
 	return blkcnt;
 }
 
+int sata_port_status(int dev, int port)
+{
+	struct sata_port_regs *port_mmio;
+	struct ahci_probe_ent *probe_ent = NULL;
+
+	if (dev < 0 || dev > (CONFIG_SYS_SATA_MAX_DEVICE - 1))
+		return -EINVAL;
+
+	if (sata_dev_desc[dev].priv == NULL)
+		return -ENODEV;
+
+	probe_ent = (struct ahci_probe_ent *)sata_dev_desc[dev].priv;
+	port_mmio = (struct sata_port_regs *)probe_ent->port[port].port_mmio;
+
+	return readl(&(port_mmio->ssts)) && SATA_PORT_SSTS_DET_MASK;
+}
+
 /*
  * SATA interface between low level driver and command layer
  */
diff --git a/drivers/net/fec_mxc.c b/drivers/net/fec_mxc.c
index 4cefda4..549d648 100644
--- a/drivers/net/fec_mxc.c
+++ b/drivers/net/fec_mxc.c
@@ -28,6 +28,14 @@ DECLARE_GLOBAL_DATA_PTR;
  */
 #define FEC_XFER_TIMEOUT	5000
 
+/*
+ * The standard 32-byte DMA alignment does not work on mx6solox, which requires
+ * 64-byte alignment in the DMA RX FEC buffer.
+ * Introduce the FEC_DMA_RX_MINALIGN which can cover mx6solox needs and also
+ * satisfies the alignment on other SoCs (32-bytes)
+ */
+#define FEC_DMA_RX_MINALIGN	64
+
 #ifndef CONFIG_MII
 #error "CONFIG_MII has to be defined!"
 #endif
@@ -711,13 +719,37 @@ static int fec_send(struct eth_device *dev, void *packet, int length)
 			break;
 	}
 
-	if (!timeout)
+	if (!timeout) {
 		ret = -EINVAL;
+		goto out;
+	}
 
-	invalidate_dcache_range(addr, addr + size);
-	if (readw(&fec->tbd_base[fec->tbd_index].status) & FEC_TBD_READY)
+	/*
+	 * The TDAR bit is cleared when the descriptors are all out from TX
+	 * but on mx6solox we noticed that the READY bit is still not cleared
+	 * right after TDAR.
+	 * These are two distinct signals, and in IC simulation, we found that
+	 * TDAR always gets cleared prior than the READY bit of last BD becomes
+	 * cleared.
+	 * In mx6solox, we use a later version of FEC IP. It looks like that
+	 * this intrinsic behaviour of TDAR bit has changed in this newer FEC
+	 * version.
+	 *
+	 * Fix this by polling the READY bit of BD after the TDAR polling,
+	 * which covers the mx6solox case and does not harm the other SoCs.
+	 */
+	timeout = FEC_XFER_TIMEOUT;
+	while (--timeout) {
+		invalidate_dcache_range(addr, addr + size);
+		if (!(readw(&fec->tbd_base[fec->tbd_index].status) &
+		    FEC_TBD_READY))
+			break;
+	}
+
+	if (!timeout)
 		ret = -EINVAL;
 
+out:
 	debug("fec_send: status 0x%x index %d ret %i\n",
 			readw(&fec->tbd_base[fec->tbd_index].status),
 			fec->tbd_index, ret);
@@ -881,9 +913,9 @@ static int fec_alloc_descs(struct fec_priv *fec)
 	/* Allocate RX buffers. */
 
 	/* Maximum RX buffer size. */
-	size = roundup(FEC_MAX_PKT_SIZE, ARCH_DMA_MINALIGN);
+	size = roundup(FEC_MAX_PKT_SIZE, FEC_DMA_RX_MINALIGN);
 	for (i = 0; i < FEC_RBD_NUM; i++) {
-		data = memalign(ARCH_DMA_MINALIGN, size);
+		data = memalign(FEC_DMA_RX_MINALIGN, size);
 		if (!data) {
 			printf("%s: error allocating rxbuf %d\n", __func__, i);
 			goto err_ring;
diff --git a/drivers/pci/pci.c b/drivers/pci/pci.c
index 4fd9c53..28859f3 100644
--- a/drivers/pci/pci.c
+++ b/drivers/pci/pci.c
@@ -648,6 +648,10 @@ int pci_hose_scan_bus(struct pci_controller *hose, int bus)
 		pci_hose_read_config_word(hose, dev, PCI_DEVICE_ID, &device);
 		pci_hose_read_config_word(hose, dev, PCI_CLASS_DEVICE, &class);
 
+#ifdef CONFIG_PCI_FIXUP_DEV
+		board_pci_fixup_dev(hose, dev, vendor, device, class);
+#endif
+
 #ifdef CONFIG_PCI_SCAN_SHOW
 		indent++;
 
diff --git a/drivers/pci/pcie_imx.c b/drivers/pci/pcie_imx.c
index a3982c4..fd7e4d4 100644
--- a/drivers/pci/pcie_imx.c
+++ b/drivers/pci/pcie_imx.c
@@ -23,13 +23,20 @@
 #define PCI_ACCESS_READ  0
 #define PCI_ACCESS_WRITE 1
 
+#ifdef CONFIG_MX6SX
+#define MX6_DBI_ADDR	0x08ffc000
+#define MX6_IO_ADDR	0x08000000
+#define MX6_MEM_ADDR	0x08100000
+#define MX6_ROOT_ADDR	0x08f00000
+#else
 #define MX6_DBI_ADDR	0x01ffc000
-#define MX6_DBI_SIZE	0x4000
 #define MX6_IO_ADDR	0x01000000
-#define MX6_IO_SIZE	0x100000
 #define MX6_MEM_ADDR	0x01100000
-#define MX6_MEM_SIZE	0xe00000
 #define MX6_ROOT_ADDR	0x01f00000
+#endif
+#define MX6_DBI_SIZE	0x4000
+#define MX6_IO_SIZE	0x100000
+#define MX6_MEM_SIZE	0xe00000
 #define MX6_ROOT_SIZE	0xfc000
 
 /* PCIe Port Logic registers (memory-mapped) */
@@ -57,6 +64,8 @@
 #define PHY_RX_OVRD_IN_LO_RX_DATA_EN (1 << 5)
 #define PHY_RX_OVRD_IN_LO_RX_PLL_EN (1 << 3)
 
+#define PCIE_PHY_PUP_REQ		(1 << 7)
+
 /* iATU registers */
 #define PCIE_ATU_VIEWPORT		0x900
 #define PCIE_ATU_REGION_INBOUND		(0x1 << 31)
@@ -421,9 +430,19 @@ static int imx_pcie_write_config(struct pci_controller *hose, pci_dev_t d,
 static int imx6_pcie_assert_core_reset(void)
 {
 	struct iomuxc *iomuxc_regs = (struct iomuxc *)IOMUXC_BASE_ADDR;
-
+#if defined(CONFIG_MX6SX)
+	struct gpc *gpc_regs = (struct gpc *)GPC_BASE_ADDR;
+
+	/* SSP_EN is not used on MX6SX anymore */
+	setbits_le32(&iomuxc_regs->gpr[12], IOMUXC_GPR12_TEST_POWERDOWN);
+	/* Force PCIe PHY reset */
+	setbits_le32(&iomuxc_regs->gpr[5], IOMUXC_GPR5_PCIE_BTNRST);
+	/* Power up PCIe PHY */
+	setbits_le32(&gpc_regs->cntr, PCIE_PHY_PUP_REQ);
+#else
 	setbits_le32(&iomuxc_regs->gpr[1], IOMUXC_GPR1_TEST_POWERDOWN);
 	clrbits_le32(&iomuxc_regs->gpr[1], IOMUXC_GPR1_REF_SSP_EN);
+#endif
 
 	return 0;
 }
@@ -441,6 +460,12 @@ static int imx6_pcie_init_phy(void)
 			IOMUXC_GPR12_LOS_LEVEL_MASK,
 			IOMUXC_GPR12_LOS_LEVEL_9);
 
+#ifdef CONFIG_MX6SX
+	clrsetbits_le32(&iomuxc_regs->gpr[12],
+			IOMUXC_GPR12_RX_EQ_MASK,
+			IOMUXC_GPR12_RX_EQ_2);
+#endif
+
 	writel((0x0 << IOMUXC_GPR8_PCS_TX_DEEMPH_GEN1_OFFSET) |
 	       (0x0 << IOMUXC_GPR8_PCS_TX_DEEMPH_GEN2_3P5DB_OFFSET) |
 	       (20 << IOMUXC_GPR8_PCS_TX_DEEMPH_GEN2_6DB_OFFSET) |
@@ -517,9 +542,16 @@ static int imx6_pcie_deassert_core_reset(void)
 	 */
 	mdelay(50);
 
+#if defined(CONFIG_MX6SX)
+	/* SSP_EN is not used on MX6SX anymore */
+	clrbits_le32(&iomuxc_regs->gpr[12], IOMUXC_GPR12_TEST_POWERDOWN);
+	/* Clear PCIe PHY reset bit */
+	clrbits_le32(&iomuxc_regs->gpr[5], IOMUXC_GPR5_PCIE_BTNRST);
+#else
 	/* Enable PCIe */
 	clrbits_le32(&iomuxc_regs->gpr[1], IOMUXC_GPR1_TEST_POWERDOWN);
 	setbits_le32(&iomuxc_regs->gpr[1], IOMUXC_GPR1_REF_SSP_EN);
+#endif
 
 	imx6_pcie_toggle_reset();
 
diff --git a/drivers/serial/serial_lpuart.c b/drivers/serial/serial_lpuart.c
index b0c6f6f..63fc388 100644
--- a/drivers/serial/serial_lpuart.c
+++ b/drivers/serial/serial_lpuart.c
@@ -14,8 +14,13 @@
 
 #define US1_TDRE        (1 << 7)
 #define US1_RDRF        (1 << 5)
+#define US1_OR          (1 << 3)
 #define UC2_TE          (1 << 3)
 #define UC2_RE          (1 << 2)
+#define CFIFO_TXFLUSH   (1 << 7)
+#define CFIFO_RXFLUSH   (1 << 6)
+#define SFIFO_RXOF      (1 << 2)
+#define SFIFO_RXUF      (1 << 0)
 
 #define STAT_LBKDIF	(1 << 31)
 #define STAT_RXEDGIF	(1 << 30)
@@ -62,14 +67,10 @@ static void lpuart_serial_setbrg(void)
 
 static int lpuart_serial_getc(void)
 {
-	u8 status;
-
-	while (!(__raw_readb(&base->us1) & US1_RDRF))
+	while (!(__raw_readb(&base->us1) & (US1_RDRF | US1_OR)))
 		WATCHDOG_RESET();
 
-	status = __raw_readb(&base->us1);
-	status |= US1_RDRF;
-	__raw_writeb(status, &base->us1);
+	barrier();
 
 	return __raw_readb(&base->ud);
 }
@@ -112,6 +113,12 @@ static int lpuart_serial_init(void)
 	__raw_writeb(0, &base->umodem);
 	__raw_writeb(0, &base->uc1);
 
+	/* Disable FIFO and flush buffer */
+	__raw_writeb(0x0, &base->upfifo);
+	__raw_writeb(0x0, &base->utwfifo);
+	__raw_writeb(0x1, &base->urwfifo);
+	__raw_writeb(CFIFO_TXFLUSH | CFIFO_RXFLUSH, &base->ucfifo);
+
 	/* provide data bits, parity, stop bit, etc */
 
 	serial_setbrg();