usb: add basic USB configs in Kconfig

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Marek Vasut <marex@denx.de>

2 files changed, 94 insertions, 0 deletions

diff --git a/drivers/usb/Kconfig b/drivers/usb/Kconfig
index e69de29..b4a9442 100644
--- a/drivers/usb/Kconfig
+++ b/drivers/usb/Kconfig
@@ -0,0 +1,46 @@
+config USB_ARCH_HAS_HCD
+	def_bool y
+
+config USB
+	bool "Support for Host-side USB"
+	depends on USB_ARCH_HAS_HCD
+	---help---
+	  Universal Serial Bus (USB) is a specification for a serial bus
+	  subsystem which offers higher speeds and more features than the
+	  traditional PC serial port.  The bus supplies power to peripherals
+	  and allows for hot swapping.  Up to 127 USB peripherals can be
+	  connected to a single USB host in a tree structure.
+
+	  The USB host is the root of the tree, the peripherals are the
+	  leaves and the inner nodes are special USB devices called hubs.
+	  Most PCs now have USB host ports, used to connect peripherals
+	  such as scanners, keyboards, mice, modems, cameras, disks,
+	  flash memory, network links, and printers to the PC.
+
+	  Say Y here if your computer has a host-side USB port and you want
+	  to use USB devices.  You then need to say Y to at least one of the
+	  Host Controller Driver (HCD) options below.  Choose a USB 1.1
+	  controller, such as "UHCI HCD support" or "OHCI HCD support",
+	  and "EHCI HCD (USB 2.0) support" except for older systems that
+	  do not have USB 2.0 support.  It doesn't normally hurt to select
+	  them all if you are not certain.
+
+	  If your system has a device-side USB port, used in the peripheral
+	  side of the USB protocol, see the "USB Gadget" framework instead.
+
+	  After choosing your HCD, then select drivers for the USB peripherals
+	  you'll be using.  You may want to check out the information provided
+	  in <file:Documentation/usb/> and especially the links given in
+	  <file:Documentation/usb/usb-help.txt>.
+
+if USB
+
+source "drivers/usb/host/Kconfig"
+
+config USB_STORAGE
+	bool "USB Mass Storage support"
+	---help---
+	  Say Y here if you want to connect USB mass storage devices to your
+	  board's USB port.
+
+endif
diff --git a/drivers/usb/host/Kconfig b/drivers/usb/host/Kconfig
new file mode 100644
index 0000000..8a6496a
--- /dev/null
+++ b/drivers/usb/host/Kconfig
@@ -0,0 +1,48 @@
+#
+# USB Host Controller Drivers
+#
+comment "USB Host Controller Drivers"
+
+config USB_XHCI_HCD
+	bool "xHCI HCD (USB 3.0) support"
+	---help---
+	  The eXtensible Host Controller Interface (xHCI) is standard for USB 3.0
+	  "SuperSpeed" host controller hardware.
+
+config USB_XHCI
+	bool
+	default USB_XHCI_HCD
+	---help---
+	  TODO: rename after most boards switch to Kconfig
+
+if USB_XHCI_HCD
+
+endif
+
+config USB_EHCI_HCD
+	bool "EHCI HCD (USB 2.0) support"
+	---help---
+	  The Enhanced Host Controller Interface (EHCI) is standard for USB 2.0
+	  "high speed" (480 Mbit/sec, 60 Mbyte/sec) host controller hardware.
+	  If your USB host controller supports USB 2.0, you will likely want to
+	  configure this Host Controller Driver.
+
+	  EHCI controllers are packaged with "companion" host controllers (OHCI
+	  or UHCI) to handle USB 1.1 devices connected to root hub ports.  Ports
+	  will connect to EHCI if the device is high speed, otherwise they
+	  connect to a companion controller.  If you configure EHCI, you should
+	  probably configure the OHCI (for NEC and some other vendors) USB Host
+	  Controller Driver or UHCI (for Via motherboards) Host Controller
+	  Driver too.
+
+	  You may want to read <file:Documentation/usb/ehci.txt>.
+
+config USB_EHCI
+	bool
+	default USB_EHCI_HCD
+	---help---
+	  TODO: rename after most boards switch to Kconfig
+
+if USB_EHCI_HCD
+
+endif