ml300: remove support for broken, orphaned board

The ml300 board has a number of issues, but nobody cares about this
long-orphaned board any more.  Remove it.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: Michal Simek <monstr@monstr.eu>

1 files changed, 0 insertions, 128 deletions

diff --git a/doc/README.ml300 b/doc/README.ml300
deleted file mode 100644
index 27c5b92..0000000
--- a/doc/README.ml300
+++ /dev/null
@@ -1,128 +0,0 @@
-Xilinx ML300 platform
-=====================
-
-0. Introduction
----------------
-
-The Xilinx ML300 board is based on the Virtex-II Pro FPGA with
-integrated AMCC PowerPC 405 core. The board is normally booted from
-System ACE CF. U-Boot is then run out of main memory.
-
-An FPGA is a configurable and thus very flexible device. To
-accommodate for this flexibility this port of U-Boot includes the
-required means to regenerate the drivers and configuration files if
-you decide to change the hardware design. The required steps are
-described below.
-
-
-1. Requirements
----------------
-
-To compile and run U-Boot on the Xilinx ML300 platform you need the
-following items.
-
-- A Xilinx ML300 platform (see http://www.xilinx.com/ml300)
-- EDK and ISE development tools (shipping with ML300)
-- Parallel4 cable (shipping with ML300)
-- The EDK reference design for ML300. You can get this as design #6 from
-  http://www.xilinx.com/ise/embedded/edk_examples.htm
-- A BOOTP/TFTP server
-
-
-2. Quick Start
---------------
-
-To compile and run U-Boot on ML300 follow the steps below. Make sure
-to consult the documentation for U-Boot, EDK, and the EDK reference
-design for ML300 if you have any questions.
-
-1. Implement the EDK reference design for ML300. You can use any of
-   the project files, for example from a xygwin shell:
-   $ xps -nw system_linux.xmp
-   XPS% run init_bram
-2. Configure and compile U-Boot. Change into the root directory of
-   U-Boot and run:
-   $ export CROSS_COMPILE=powerpc-eabi-
-   $ make ml300_config
-   $ make
-3. Set up the ML300, connect the Parallel4 and the serial cable. Start
-   a terminal on your host computer and set the communication
-   parameters to 9600,8N1,no handshake.
-4. Set up the BOOTP/TFTP server on your host machine. U-Boot is
-   preconfigured to use a fixed HW MAC address of 00:0A:35:00:22:01.
-5. Download the bitstream to the ML300.
-6. Use XMD to download and run U-Boot on the ML300:
-   $ xmd
-   XMD% ppcconnect
-   XMD% dow u-boot
-   XMD% run
-
-You can now make an ACE file out of bitstream and U-Boot:
-   $ xmd genace.tcl -jprog -board ml300 -hw  \
-     implementation/download.bit -elf u-boot -ace top.ace
-
-Put the ACE file onto the MicroDrive, for example into xilinx/myace,
-and reboot ML300.
-
-
-3. Generating a Custom BSP for U-Boot
--------------------------------------
-
-If you decide to change the EDK reference design for ML300 or if you
-build a new design from scratch either with the Base System Builder in
-XPS or all by hand you most likely will change the base addresses for
-the Uart and the Ethernet peripheral. If you do so you will have two
-options:
-
-1. Edit boards/xilinx/ml300/xparameters.h to reflect the changes you
-   made to your hardware.
-2. Use the MLD technology provided by Xilinx Platform Studio to make
-   the changes automatically. To do so go to the root directory of the
-   EDK reference design for ML300. Copy the Linux project file and the
-   Linux software configuration file:
-   $ cp system_linux.xmp system_uboot.xmp
-   $ cp system_linux.mss system_uboot.mss
-
-   Edit system_uboot.xmp and and have it point to system_uboot.mss for
-   the software configuration.
-
-   Then, copy the sw_services directory in
-   boards/xilinx/ml300/sw_services to the root directory of the EDK
-   reference design for ML300.
-   $ cp -R <uboot dir>/boards/xilinx/ml300/sw_services <edk dir>
-
-   Modify system_uboot.mss. Look for the Linux library definition
-   and change it to generate a BSP for U-Boot. An example, might look
-   like this:
-
-   BEGIN LIBRARY
-    PARAMETER LIBRARY_NAME = uboot
-    PARAMETER LIBRARY_VER = 1.00.a
-    PARAMETER CONNECTED_PERIPHS = (opb_uart16550_0,opb_ethernet_0)
-    PARAMETER TARGET_DIR = <uboot dir>
-   END
-
-   Now, you are ready to generate the Xilinx ML300 BSP for U-Boot:
-   $ xps -nw system_uboot.xmp
-   XPS% run libs
-
-   If all goes well the new configuration has been copied into the
-   right places within the U-Boot source tree. Recompile U-Boot and
-   run it on the ML300.
-
-
-4. ToDo
--------
-
-- Add support for all other peripherals on ML300.
-- Read the MAC address out of the IIC EEPROM.
-- Store the bootargs in the IIC EEPROM.
-
-
-5. References
--------------
-
-ML300:			http://www.xilinx.com/ml300
-EDK:			http://www.xilinx.com/edk
-ISE:			http://www.xilinx.com/ise
-Reference Design:	http://www.xilinx.com/ise/embedded/edk_examples.htm