arm: Remove vision2 board

This board has not been converted to generic board by the deadline.
Remove it.

Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Stefano Babic <sbabic@denx.de>

5 files changed, 0 insertions, 814 deletions

diff --git a/board/ttcontrol/vision2/Kconfig b/board/ttcontrol/vision2/Kconfig
deleted file mode 100644
index cacd2c5..0000000
--- a/board/ttcontrol/vision2/Kconfig
+++ /dev/null
@@ -1,15 +0,0 @@
-if TARGET_VISION2
-
-config SYS_BOARD
-	default "vision2"
-
-config SYS_VENDOR
-	default "ttcontrol"
-
-config SYS_SOC
-	default "mx5"
-
-config SYS_CONFIG_NAME
-	default "vision2"
-
-endif
diff --git a/board/ttcontrol/vision2/MAINTAINERS b/board/ttcontrol/vision2/MAINTAINERS
deleted file mode 100644
index cfc9903..0000000
--- a/board/ttcontrol/vision2/MAINTAINERS
+++ /dev/null
@@ -1,6 +0,0 @@
-VISION2 BOARD
-M:	Stefano Babic <sbabic@denx.de>
-S:	Maintained
-F:	board/ttcontrol/vision2/
-F:	include/configs/vision2.h
-F:	configs/vision2_defconfig
diff --git a/board/ttcontrol/vision2/Makefile b/board/ttcontrol/vision2/Makefile
deleted file mode 100644
index c3e1e87..0000000
--- a/board/ttcontrol/vision2/Makefile
+++ /dev/null
@@ -1,9 +0,0 @@
-#
-# Copyright (C) 2007, Guennadi Liakhovetski <lg@denx.de>
-#
-# (C) Copyright 2009 Freescale Semiconductor, Inc.
-#
-# SPDX-License-Identifier:	GPL-2.0+
-#
-
-obj-y	:= vision2.o
diff --git a/board/ttcontrol/vision2/imximage_hynix.cfg b/board/ttcontrol/vision2/imximage_hynix.cfg
deleted file mode 100644
index c74973e..0000000
--- a/board/ttcontrol/vision2/imximage_hynix.cfg
+++ /dev/null
@@ -1,212 +0,0 @@
-/*
- * (C) Copyright 2009
- * Stefano Babic DENX Software Engineering sbabic@denx.de.
- *
- * (C) Copyright 2010
- * Klaus Steinhammer TTECH Control Gmbh kst@tttech.com
- *
- * SPDX-License-Identifier:	GPL-2.0+
- *
- * Refer doc/README.imximage for more details about how-to configure
- * and create imximage boot image
- *
- * The syntax is taken as close as possible with the kwbimage
- */
-
-/*
- * Boot Device : one of
- * spi, nand, onenand, sd
- */
-BOOT_FROM	spi
-
-/*
- * Device Configuration Data (DCD)
- *
- * Each entry must have the format:
- * Addr-type           Address        Value
- *
- * where:
- *	Addr-type register length (1,2 or 4 bytes)
- *	Address	  absolute address of the register
- *	value	  value to be stored in the register
- */
-
-/*
- * #######################
- * ### Disable WDOG ###
- * #######################
- */
-DATA 2 0x73f98000 0x30
-
-/*
- * #######################
- * ### SET DDR Clk     ###
- * #######################
- */
-/* CCM: CBMCR - ddr_clk_sel: axi_b (133MHz) */
-DATA 4 0x73FD4018 0x000024C0
-
-/* DOUBLE SPI CLK (13MHz->26 MHz Clock) */
-DATA 4 0x73FD4038 0x2010241
-
-/* IOMUXC_SW_PAD_CTL_PAD_CSPI1_MOSI HYS_ENABLE | DRV_MAX | SRE_FAST */
-DATA 4 0x73fa8600 0x00000107
-/* IOMUXC_SW_PAD_CTL_PAD_CSPI1_MISO HYS_ENABLE | DRV_MAX | SRE_FAST */
-DATA 4 0x73fa8604 0x00000107
-/* IOMUXC_SW_PAD_CTL_PAD_CSPI1_SS0 HYS_ENABLE | PKE_ENABLE | DRV_MAX | SRE_FAST */
-DATA 4 0x73fa8608 0x00000187
-/* IOMUXC_SW_PAD_CTL_PAD_CSPI1_SS1 HYS_ENABLE | PKE_ENABLE | DRV_MAX | SRE_FAST */
-DATA 4 0x73fa860c 0x00000187
-/* IOMUXC_SW_PAD_CTL_PAD_CSPI1_SCLK HYS_ENABLE | DRV_MAX | SRE_FAST */
-DATA 4 0x73fa8614 0x00000107
-/* IOMUXC_SW_PAD_CTL_PAD_DI1_PIN11 HYS_ENABLE | DRV_MAX | SRE_FAST (CSPI1_SS2) */
-DATA 4 0x73fa86a8 0x00000187
-
-/*
- * #######################
- * ### Settings IOMUXC ###
- * #######################
- */
-/*
- * DDR IOMUX configuration
- * Control, Data, Address pads are in their default state: HIGH DS, FAST SR.
- * IOMUXC_SW_PAD_CTL_PAD_DRAM_SDCLK MAX DS
- */
-DATA 4 0x73fa84b8 0x000000e7
-/* PVTC MAX (at GPC, PGR reg) */
-/* DATA 4 0x73FD8004 0x1fc00000 */
-
-/* DQM0 DS high slew rate slow */
-DATA 4 0x73fa84d4 0x000000e4
-/* DQM1 DS high slew rate slow */
-DATA 4 0x73fa84d8 0x000000e4
-/* DQM2 DS high slew rate slow */
-DATA 4 0x73fa84dc 0x000000e4
-/* DQM3 DS high slew rate slow */
-DATA 4 0x73fa84e0 0x000000e4
-
-/* IOMUXC_SW_PAD_CTL_PAD_DRAM_SDQS0 DS high & SLEW slow */
-DATA 4 0x73fa84bc 0x000000c4
-/* IOMUXC_SW_PAD_CTL_PAD_DRAM_SDQS1 DS high & SLEW slow */
-DATA 4 0x73fa84c0 0x000000c4
-/* IOMUXC_SW_PAD_CTL_PAD_DRAM_SDQS2 DS high & SLEW slow */
-DATA 4 0x73fa84c4 0x000000c4
-/* IOMUXC_SW_PAD_CTL_PAD_DRAM_SDQS3 DS high & SLEW slow */
-DATA 4 0x73fa84c8 0x000000c4
-
-/* DRAM_DATA B0 */
-DATA 4 0x73fa88a4 0x00000004
-/* DRAM_DATA B1 */
-DATA 4 0x73fa88ac 0x00000004
-/* DRAM_DATA B2 */
-DATA 4 0x73fa88b8 0x00000004
-/* DRAM_DATA B3 */
-DATA 4 0x73fa882c 0x00000004
-
-/* DRAM_DATA B0 slew rate */
-DATA 4 0x73fa8878 0x00000000
-/* DRAM_DATA B1 slew rate */
-DATA 4 0x73fa8880 0x00000000
-/* DRAM_DATA B2 slew rate */
-DATA 4 0x73fa888c 0x00000000
-/* DRAM_DATA B3 slew rate */
-DATA 4 0x73fa889c 0x00000000
-
-/*
- * #######################
- * ### Configure SDRAM ###
- * #######################
- */
-
-/* Configure CS0 */
-/* ####################### */
-
-/* ESDCTL0: Enable controller */
-DATA 4 0x83fd9000 0x83220000
-
-/* Init DRAM on CS0 */
-/* ESDSCR: Precharge command */
-DATA 4 0x83fd9014 0x04008008
-/* ESDSCR: Refresh command */
-DATA 4 0x83fd9014 0x00008010
-/* ESDSCR: Refresh command */
-DATA 4 0x83fd9014 0x00008010
-/* ESDSCR: LMR with CAS=3 and BL=3 (Burst Length = 8) */
-DATA 4 0x83fd9014 0x00338018
-/* ESDSCR: EMR with half Drive strength (= medium strength @ i.MX51) */
-DATA 4 0x83fd9014 0x0020801a
-/* ESDSCR */
-DATA 4 0x83fd9014 0x00008000
-
-/* ESDSCR: EMR with full Drive strength */
-/* DATA 4 0x83fd9014 0x0000801a */
-
-/* ESDCTL0: 14 ROW, 10 COL, 32Bit, SREF=8 */
-DATA 4 0x83fd9000 0xC3220000
-
-/*
- * ESDCFG0: tRFC:22clks, tXSR:28clks, tXP:2clks, tWTR:2clk, tRP:3clks, tMRD:2clks
- *          tRAS:8clks, tRRD:2clks, tWR:3clks, tRCD:3clks, tRC:11clks
- * DATA 4 0x83fd9004 0xC33574AA
- */
-/*
- * micron mDDR
- * ESDCFG0: tRFC:11clks, tXSR:19clks, tXP:1clks, tWTR:2clk, tRP:3clks, tMRD:2clks
- * tRAS:7clks, tRRD:2clks, tWR:3clks, tRCD:3clks, tRC:9clks
- * DATA 4 0x83FD9004 0x101564a8
- */
-/*
- * hynix mDDR
- * ESDCFG0: tRFC:17clks, tXSR:21clks, tXP:3clks, tWTR:1clk, tRP:3clks, tMRD:2clks
- * tRAS:7clks, tRRD:2clks, tWR:3clks, tRCD:3clks, tRC:9clks
- */
-DATA 4 0x83FD9004 0x704564a8
-
-/* ESDMISC: AP=10, Bank interleaving on, MIF3 en, RALAT=2 */
-DATA 4 0x83fd9010 0x000a1700
-
-/* Configure CS1 */
-/* ####################### */
-
-/* ESDCTL1: Enable controller */
-DATA 4 0x83fd9008 0x83220000
-
-/* Init DRAM on CS1 */
-/* ESDSCR: Precharge command */
-DATA 4 0x83fd9014 0x0400800c
-/* ESDSCR: Refresh command */
-DATA 4 0x83fd9014 0x00008014
-/* ESDSCR: Refresh command */
-DATA 4 0x83fd9014 0x00008014
-/* ESDSCR: LMR with CAS=3 and BL=3 (Burst Length = 8) */
-DATA 4 0x83fd9014 0x0033801c
-/* ESDSCR: EMR with half Drive strength (= medium strength @ i.MX51) */
-DATA 4 0x83fd9014 0x0020801e
-/* ESDSCR */
-DATA 4 0x83fd9014 0x00008004
-
-/* ESDCTL1: 14 ROW, 10 COL, 32Bit, SREF=8 */
-DATA 4 0x83fd9008 0xC3220000
-/*
- * ESDCFG1: tRFC:22clks, tXSR:28clks, tXP:2clks, tWTR:2clk, tRP:3clks, tMRD:2clks
- *          tRAS:8clks, tRRD:2clks, tWR:3clks, tRCD:3clks, tRC:11clks
- * DATA 4 0x83fd900c 0xC33574AA
- */
-/*
- * micron mDDR
- * ESDCFG1: tRFC:11clks, tXSR:19clks, tXP:1clks, tWTR:2clk, tRP:3clks, tMRD:2clks
- * tRAS:7clks, tRRD:2clks, tWR:3clks, tRCD:3clks, tRC:9clks
- * DATA 4 0x83FD900C 0x101564a8
- */
-/*
- * hynix mDDR
- * ESDCFG0: tRFC:17clks, tXSR:21clks, tXP:3clks, tWTR:1clk, tRP:3clks, tMRD:2clks
- * tRAS:7clks, tRRD:2clks, tWR:3clks, tRCD:3clks, tRC:9clks
- */
-DATA 4 0x83FD900C 0x704564a8
-
-/* ESDSCR (mDRAM configuration finished) */
-DATA 4 0x83FD9014 0x00000004
-
-/* ESDSCR - clear "configuration request" bit */
-DATA 4 0x83fd9014 0x00000000
diff --git a/board/ttcontrol/vision2/vision2.c b/board/ttcontrol/vision2/vision2.c
deleted file mode 100644
index 247991d..0000000
--- a/board/ttcontrol/vision2/vision2.c
+++ /dev/null
@@ -1,572 +0,0 @@
-/*
- * (C) Copyright 2010
- * Stefano Babic, DENX Software Engineering, sbabic@denx.de.
- *
- * (C) Copyright 2009 Freescale Semiconductor, Inc.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#include <common.h>
-#include <asm/io.h>
-#include <asm/arch/imx-regs.h>
-#include <asm/arch/crm_regs.h>
-#include <asm/arch/clock.h>
-#include <asm/arch/iomux-mx51.h>
-#include <asm/gpio.h>
-#include <asm/arch/sys_proto.h>
-#include <asm/imx-common/spi.h>
-#include <i2c.h>
-#include <mmc.h>
-#include <power/pmic.h>
-#include <fsl_esdhc.h>
-#include <fsl_pmic.h>
-#include <mc13892.h>
-#include <linux/fb.h>
-
-#include <ipu_pixfmt.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-static struct fb_videomode const nec_nl6448bc26_09c = {
-	"NEC_NL6448BC26-09C",
-	60,	/* Refresh */
-	640,	/* xres */
-	480,	/* yres */
-	37650,	/* pixclock = 26.56Mhz */
-	48,	/* left margin */
-	16,	/* right margin */
-	31,	/* upper margin */
-	12,	/* lower margin */
-	96,	/* hsync-len */
-	2,	/* vsync-len */
-	0,	/* sync */
-	FB_VMODE_NONINTERLACED,	/* vmode */
-	0,	/* flag */
-};
-
-#ifdef CONFIG_HW_WATCHDOG
-#include <watchdog.h>
-void hw_watchdog_reset(void)
-{
-	int val;
-
-	/* toggle watchdog trigger pin */
-	val = gpio_get_value(IMX_GPIO_NR(3, 2));
-	val = val ? 0 : 1;
-	gpio_set_value(IMX_GPIO_NR(3, 2), val);
-}
-#endif
-
-static void init_drive_strength(void)
-{
-	static const iomux_v3_cfg_t ddr_pads[] = {
-		NEW_PAD_CTRL(MX51_GRP_PKEDDR, 0),
-		NEW_PAD_CTRL(MX51_GRP_PKEADDR, PAD_CTL_PKE),
-		NEW_PAD_CTRL(MX51_GRP_DDRAPKS, 0),
-		NEW_PAD_CTRL(MX51_GRP_DDRAPUS, PAD_CTL_PUS_100K_UP),
-		NEW_PAD_CTRL(MX51_GRP_DDR_SR_A1, PAD_CTL_SRE_FAST),
-		NEW_PAD_CTRL(MX51_GRP_DDR_A0, PAD_CTL_DSE_HIGH),
-		NEW_PAD_CTRL(MX51_GRP_DDR_A1, PAD_CTL_DSE_HIGH),
-		NEW_PAD_CTRL(MX51_PAD_DRAM_RAS__DRAM_RAS,
-				PAD_CTL_DSE_HIGH | PAD_CTL_SRE_FAST),
-		NEW_PAD_CTRL(MX51_PAD_DRAM_CAS__DRAM_CAS,
-				PAD_CTL_DSE_HIGH | PAD_CTL_SRE_FAST),
-		NEW_PAD_CTRL(MX51_GRP_PKEDDR, PAD_CTL_PKE),
-		NEW_PAD_CTRL(MX51_GRP_DDRPKS, 0),
-		NEW_PAD_CTRL(MX51_GRP_HYSDDR0, 0),
-		NEW_PAD_CTRL(MX51_GRP_HYSDDR1, 0),
-		NEW_PAD_CTRL(MX51_GRP_HYSDDR2, 0),
-		NEW_PAD_CTRL(MX51_GRP_HYSDDR3, 0),
-		NEW_PAD_CTRL(MX51_GRP_DRAM_SR_B0, PAD_CTL_SRE_FAST),
-		NEW_PAD_CTRL(MX51_GRP_DRAM_SR_B1, PAD_CTL_SRE_FAST),
-		NEW_PAD_CTRL(MX51_GRP_DRAM_SR_B2, PAD_CTL_SRE_FAST),
-		NEW_PAD_CTRL(MX51_GRP_DRAM_SR_B4, PAD_CTL_SRE_FAST),
-		NEW_PAD_CTRL(MX51_GRP_DDRPUS, PAD_CTL_PUS_100K_UP),
-		NEW_PAD_CTRL(MX51_GRP_INMODE1, 0),
-		NEW_PAD_CTRL(MX51_GRP_DRAM_B0, PAD_CTL_DSE_MED),
-		NEW_PAD_CTRL(MX51_GRP_DRAM_B1, PAD_CTL_DSE_MED),
-		NEW_PAD_CTRL(MX51_GRP_DRAM_B2, PAD_CTL_DSE_MED),
-		NEW_PAD_CTRL(MX51_GRP_DRAM_B4, PAD_CTL_DSE_MED),
-
-		NEW_PAD_CTRL(MX51_PAD_DRAM_SDWE__DRAM_SDWE, MX51_GPIO_PAD_CTRL),
-		NEW_PAD_CTRL(MX51_PAD_DRAM_SDCKE0__DRAM_SDCKE0,
-				MX51_GPIO_PAD_CTRL),
-		NEW_PAD_CTRL(MX51_PAD_DRAM_SDCKE1__DRAM_SDCKE1,
-				MX51_GPIO_PAD_CTRL),
-		NEW_PAD_CTRL(MX51_PAD_DRAM_SDCLK__DRAM_SDCLK,
-				MX51_GPIO_PAD_CTRL),
-		NEW_PAD_CTRL(MX51_PAD_DRAM_SDQS0__DRAM_SDQS0,
-				MX51_GPIO_PAD_CTRL),
-		NEW_PAD_CTRL(MX51_PAD_DRAM_SDQS1__DRAM_SDQS1,
-				MX51_GPIO_PAD_CTRL),
-		NEW_PAD_CTRL(MX51_PAD_DRAM_SDQS2__DRAM_SDQS2,
-				MX51_GPIO_PAD_CTRL),
-		NEW_PAD_CTRL(MX51_PAD_DRAM_SDQS3__DRAM_SDQS3,
-				MX51_GPIO_PAD_CTRL),
-		NEW_PAD_CTRL(MX51_PAD_DRAM_CS0__DRAM_CS0, MX51_GPIO_PAD_CTRL),
-		NEW_PAD_CTRL(MX51_PAD_DRAM_CS1__DRAM_CS1, MX51_GPIO_PAD_CTRL),
-		NEW_PAD_CTRL(MX51_PAD_DRAM_DQM0__DRAM_DQM0, MX51_GPIO_PAD_CTRL),
-		NEW_PAD_CTRL(MX51_PAD_DRAM_DQM1__DRAM_DQM1, MX51_GPIO_PAD_CTRL),
-		NEW_PAD_CTRL(MX51_PAD_DRAM_DQM2__DRAM_DQM2, MX51_GPIO_PAD_CTRL),
-		NEW_PAD_CTRL(MX51_PAD_DRAM_DQM3__DRAM_DQM3, MX51_GPIO_PAD_CTRL),
-	};
-
-	imx_iomux_v3_setup_multiple_pads(ddr_pads, ARRAY_SIZE(ddr_pads));
-}
-
-int dram_init(void)
-{
-	gd->ram_size = get_ram_size((long *)PHYS_SDRAM_1,
-		PHYS_SDRAM_1_SIZE);
-
-	return 0;
-}
-
-static void setup_weim(void)
-{
-	struct weim  *pweim = (struct weim *)WEIM_BASE_ADDR;
-
-	pweim->cs0gcr1 = 0x004100b9;
-	pweim->cs0gcr2 = 0x00000001;
-	pweim->cs0rcr1 = 0x0a018000;
-	pweim->cs0rcr2 = 0;
-	pweim->cs0wcr1 = 0x0704a240;
-}
-
-static void setup_uart(void)
-{
-	static const iomux_v3_cfg_t uart_pads[] = {
-		MX51_PAD_EIM_D25__UART3_RXD, /* console RX */
-		MX51_PAD_EIM_D26__UART3_TXD, /* console TX */
-	};
-
-	imx_iomux_v3_setup_multiple_pads(uart_pads, ARRAY_SIZE(uart_pads));
-}
-
-#ifdef CONFIG_MXC_SPI
-int board_spi_cs_gpio(unsigned bus, unsigned cs)
-{
-	return (bus == 0 && cs == 1) ? 121 : -1;
-}
-
-void spi_io_init(void)
-{
-	static const iomux_v3_cfg_t spi_pads[] = {
-		NEW_PAD_CTRL(MX51_PAD_CSPI1_MOSI__ECSPI1_MOSI, PAD_CTL_HYS |
-				PAD_CTL_DSE_MAX | PAD_CTL_SRE_FAST),
-		NEW_PAD_CTRL(MX51_PAD_CSPI1_MISO__ECSPI1_MISO, PAD_CTL_HYS |
-				PAD_CTL_DSE_MAX | PAD_CTL_SRE_FAST),
-		NEW_PAD_CTRL(MX51_PAD_CSPI1_SS0__ECSPI1_SS0, PAD_CTL_HYS |
-			PAD_CTL_PKE | PAD_CTL_DSE_MAX | PAD_CTL_SRE_FAST),
-		NEW_PAD_CTRL(MX51_PAD_CSPI1_SS1__ECSPI1_SS1, PAD_CTL_HYS |
-			PAD_CTL_PKE | PAD_CTL_DSE_MAX | PAD_CTL_SRE_FAST),
-		NEW_PAD_CTRL(MX51_PAD_DI1_PIN11__ECSPI1_SS2, PAD_CTL_HYS |
-			PAD_CTL_PKE | PAD_CTL_DSE_MAX | PAD_CTL_SRE_FAST),
-		NEW_PAD_CTRL(MX51_PAD_CSPI1_SCLK__ECSPI1_SCLK, PAD_CTL_HYS |
-				PAD_CTL_DSE_MAX | PAD_CTL_SRE_FAST),
-	};
-
-	imx_iomux_v3_setup_multiple_pads(spi_pads, ARRAY_SIZE(spi_pads));
-}
-
-static void reset_peripherals(int reset)
-{
-#ifdef CONFIG_VISION2_HW_1_0
-	static const iomux_v3_cfg_t fec_cfg_pads[] = {
-		/* RXD1 */
-		NEW_PAD_CTRL(MX51_PAD_EIM_EB3__GPIO2_23, NO_PAD_CTRL),
-		/* RXD2 */
-		NEW_PAD_CTRL(MX51_PAD_EIM_CS2__GPIO2_27, NO_PAD_CTRL),
-		/* RXD3 */
-		NEW_PAD_CTRL(MX51_PAD_EIM_CS3__GPIO2_28, NO_PAD_CTRL),
-		/* RXER */
-		NEW_PAD_CTRL(MX51_PAD_EIM_CS4__GPIO2_29, NO_PAD_CTRL),
-		/* COL */
-		NEW_PAD_CTRL(MX51_PAD_NANDF_RB2__GPIO3_10, NO_PAD_CTRL),
-		/* RCLK */
-		NEW_PAD_CTRL(MX51_PAD_NANDF_RB3__GPIO3_11, NO_PAD_CTRL),
-		/* RXD0 */
-		NEW_PAD_CTRL(MX51_PAD_NANDF_D9__GPIO3_31, NO_PAD_CTRL),
-	};
-
-	static const iomux_v3_cfg_t fec_pads[] = {
-		NEW_PAD_CTRL(MX51_PAD_EIM_CS3__FEC_RDATA3, MX51_PAD_CTRL_2),
-		NEW_PAD_CTRL(MX51_PAD_EIM_CS2__FEC_RDATA2, MX51_PAD_CTRL_2),
-		NEW_PAD_CTRL(MX51_PAD_EIM_EB3__FEC_RDATA1, MX51_PAD_CTRL_2),
-		MX51_PAD_NANDF_D9__FEC_RDATA0,
-		NEW_PAD_CTRL(MX51_PAD_NANDF_RB3__FEC_RX_CLK, MX51_PAD_CTRL_4),
-		MX51_PAD_EIM_CS4__FEC_RX_ER,
-		NEW_PAD_CTRL(MX51_PAD_NANDF_RB2__FEC_COL, MX51_PAD_CTRL_4),
-	};
-#endif
-
-	if (reset) {
-
-		/* reset_n is on NANDF_D15 */
-		gpio_direction_output(IMX_GPIO_NR(3, 25), 0);
-
-#ifdef CONFIG_VISION2_HW_1_0
-		/*
-		 * set FEC Configuration lines
-		 * set levels of FEC config lines
-		 */
-		gpio_direction_output(IMX_GPIO_NR(3, 11), 0);
-		gpio_direction_output(IMX_GPIO_NR(3, 10), 1);
-		gpio_direction_output(IMX_GPIO_NR(3, 31), 1);
-
-		/* set direction of FEC config lines */
-		gpio_direction_output(IMX_GPIO_NR(2, 27), 0);
-		gpio_direction_output(IMX_GPIO_NR(2, 28), 0);
-		gpio_direction_output(IMX_GPIO_NR(2, 29), 0);
-		gpio_direction_output(IMX_GPIO_NR(2, 23), 1);
-
-		imx_iomux_v3_setup_multiple_pads(fec_cfg_pads,
-						 ARRAY_SIZE(fec_cfg_pads));
-#endif
-
-		/* activate reset_n pin */
-		imx_iomux_v3_setup_pad(
-				NEW_PAD_CTRL(MX51_PAD_NANDF_D15__GPIO3_25,
-						PAD_CTL_DSE_MAX));
-	} else {
-		/* set FEC Control lines */
-		gpio_direction_input(IMX_GPIO_NR(3, 25));
-		udelay(500);
-
-#ifdef CONFIG_VISION2_HW_1_0
-		imx_iomux_v3_setup_multiple_pads(fec_pads,
-							ARRAY_SIZE(fec_pads));
-#endif
-	}
-}
-
-static void power_init_mx51(void)
-{
-	unsigned int val;
-	struct pmic *p;
-	int ret;
-
-	ret = pmic_init(I2C_PMIC);
-	if (ret)
-		return;
-
-	p = pmic_get("FSL_PMIC");
-	if (!p)
-		return;
-
-	/* Write needed to Power Gate 2 register */
-	pmic_reg_read(p, REG_POWER_MISC, &val);
-
-	/* enable VCAM with 2.775V to enable read from PMIC */
-	val = VCAMCONFIG | VCAMEN;
-	pmic_reg_write(p, REG_MODE_1, val);
-
-	/*
-	 * Set switchers in Auto in NORMAL mode & STANDBY mode
-	 * Setup the switcher mode for SW1 & SW2
-	 */
-	pmic_reg_read(p, REG_SW_4, &val);
-	val = (val & ~((SWMODE_MASK << SWMODE1_SHIFT) |
-		(SWMODE_MASK << SWMODE2_SHIFT)));
-	val |= (SWMODE_AUTO_AUTO << SWMODE1_SHIFT) |
-		(SWMODE_AUTO_AUTO << SWMODE2_SHIFT);
-	pmic_reg_write(p, REG_SW_4, val);
-
-	/* Setup the switcher mode for SW3 & SW4 */
-	pmic_reg_read(p, REG_SW_5, &val);
-	val &= ~((SWMODE_MASK << SWMODE4_SHIFT) |
-		(SWMODE_MASK << SWMODE3_SHIFT));
-	val |= (SWMODE_AUTO_AUTO << SWMODE4_SHIFT) |
-		(SWMODE_AUTO_AUTO << SWMODE3_SHIFT);
-	pmic_reg_write(p, REG_SW_5, val);
-
-
-	/* Set VGEN3 to 1.8V, VCAM to 3.0V */
-	pmic_reg_read(p, REG_SETTING_0, &val);
-	val &= ~(VCAM_MASK | VGEN3_MASK);
-	val |= VCAM_3_0;
-	pmic_reg_write(p, REG_SETTING_0, val);
-
-	/* Set VVIDEO to 2.775V, VAUDIO to 3V0, VSD to 1.8V */
-	pmic_reg_read(p, REG_SETTING_1, &val);
-	val &= ~(VVIDEO_MASK | VSD_MASK | VAUDIO_MASK);
-	val |= VVIDEO_2_775 | VAUDIO_3_0 | VSD_1_8;
-	pmic_reg_write(p, REG_SETTING_1, val);
-
-	/* Configure VGEN3 and VCAM regulators to use external PNP */
-	val = VGEN3CONFIG | VCAMCONFIG;
-	pmic_reg_write(p, REG_MODE_1, val);
-	udelay(200);
-
-	/* Enable VGEN3, VCAM, VAUDIO, VVIDEO, VSD regulators */
-	val = VGEN3EN | VGEN3CONFIG | VCAMEN | VCAMCONFIG |
-		VVIDEOEN | VAUDIOEN  | VSDEN;
-	pmic_reg_write(p, REG_MODE_1, val);
-
-	pmic_reg_read(p, REG_POWER_CTL2, &val);
-	val |= WDIRESET;
-	pmic_reg_write(p, REG_POWER_CTL2, val);
-
-	udelay(2500);
-
-}
-#endif
-
-static void setup_gpios(void)
-{
-	static const iomux_v3_cfg_t gpio_pads_1[] = {
-		NEW_PAD_CTRL(MX51_PAD_GPIO1_7__GPIO1_7, PAD_CTL_PKE |
-				PAD_CTL_DSE_MED), /* CAM_SUP_DISn */
-		NEW_PAD_CTRL(MX51_PAD_DI1_PIN12__GPIO3_1, PAD_CTL_PKE |
-				PAD_CTL_DSE_MED), /* DAB Display EN */
-		NEW_PAD_CTRL(MX51_PAD_DI1_PIN13__GPIO3_2, PAD_CTL_PKE |
-				PAD_CTL_DSE_MED), /* WDOG_TRIGGER */
-	};
-
-	static const iomux_v3_cfg_t gpio_pads_2[] = {
-		NEW_PAD_CTRL(MX51_PAD_DI1_D0_CS__GPIO3_3, PAD_CTL_PKE |
-				PAD_CTL_DSE_MED), /* Display2 TxEN */
-		NEW_PAD_CTRL(MX51_PAD_DI1_D1_CS__GPIO3_4, PAD_CTL_PKE |
-				PAD_CTL_DSE_MED), /* DAB Light EN */
-		NEW_PAD_CTRL(MX51_PAD_DISPB2_SER_DIN__GPIO3_5, PAD_CTL_PKE |
-				PAD_CTL_DSE_MED), /* AUDIO_MUTE */
-		NEW_PAD_CTRL(MX51_PAD_DISPB2_SER_DIO__GPIO3_6, PAD_CTL_PKE |
-				PAD_CTL_DSE_MED), /* SPARE_OUT */
-		NEW_PAD_CTRL(MX51_PAD_NANDF_D14__GPIO3_26, PAD_CTL_PKE |
-				PAD_CTL_DSE_MED), /* BEEPER_EN */
-		NEW_PAD_CTRL(MX51_PAD_NANDF_D13__GPIO3_27, PAD_CTL_PKE |
-				PAD_CTL_DSE_MED), /* POWER_OFF */
-		NEW_PAD_CTRL(MX51_PAD_NANDF_D10__GPIO3_30, PAD_CTL_PKE |
-				PAD_CTL_DSE_MED), /* FRAM_WE */
-		NEW_PAD_CTRL(MX51_PAD_CSPI1_RDY__GPIO4_26, PAD_CTL_PKE |
-				PAD_CTL_DSE_MED), /* EXPANSION_EN */
-		MX51_PAD_GPIO1_2__PWM1_PWMO,
-	};
-
-	unsigned int i;
-
-	imx_iomux_v3_setup_multiple_pads(gpio_pads_1, ARRAY_SIZE(gpio_pads_1));
-
-	/* Now we need to trigger the watchdog */
-	WATCHDOG_RESET();
-
-	imx_iomux_v3_setup_multiple_pads(gpio_pads_2, ARRAY_SIZE(gpio_pads_2));
-
-	/*
-	 * Set GPIO1_4 to high and output; it is used to reset
-	 * the system on reboot
-	 */
-	gpio_direction_output(IMX_GPIO_NR(1, 4), 1);
-
-	gpio_direction_output(IMX_GPIO_NR(1, 7), 0);
-	for (i = IMX_GPIO_NR(3, 1); i < IMX_GPIO_NR(3, 7); i++)
-		gpio_direction_output(i, 0);
-
-	gpio_direction_output(IMX_GPIO_NR(3, 30), 0);
-
-	/* Set POWER_OFF high */
-	gpio_direction_output(IMX_GPIO_NR(3, 27), 1);
-
-	gpio_direction_output(IMX_GPIO_NR(3, 26), 0);
-
-	gpio_direction_output(IMX_GPIO_NR(4, 26), 0);
-
-	gpio_direction_output(IMX_GPIO_NR(4, 25), 1);
-
-	WATCHDOG_RESET();
-}
-
-static void setup_fec(void)
-{
-	static const iomux_v3_cfg_t fec_pads[] = {
-		NEW_PAD_CTRL(MX51_PAD_EIM_EB2__FEC_MDIO, PAD_CTL_HYS |
-				PAD_CTL_PUS_22K_UP | PAD_CTL_ODE |
-				PAD_CTL_DSE_HIGH | PAD_CTL_SRE_FAST),
-		MX51_PAD_NANDF_CS3__FEC_MDC,
-		NEW_PAD_CTRL(MX51_PAD_EIM_CS3__FEC_RDATA3, MX51_PAD_CTRL_2),
-		NEW_PAD_CTRL(MX51_PAD_EIM_CS2__FEC_RDATA2, MX51_PAD_CTRL_2),
-		NEW_PAD_CTRL(MX51_PAD_EIM_EB3__FEC_RDATA1, MX51_PAD_CTRL_2),
-		MX51_PAD_NANDF_D9__FEC_RDATA0,
-		MX51_PAD_NANDF_CS6__FEC_TDATA3,
-		MX51_PAD_NANDF_CS5__FEC_TDATA2,
-		MX51_PAD_NANDF_CS4__FEC_TDATA1,
-		MX51_PAD_NANDF_D8__FEC_TDATA0,
-		MX51_PAD_NANDF_CS7__FEC_TX_EN,
-		MX51_PAD_NANDF_CS2__FEC_TX_ER,
-		MX51_PAD_NANDF_RDY_INT__FEC_TX_CLK,
-		NEW_PAD_CTRL(MX51_PAD_NANDF_RB2__FEC_COL, MX51_PAD_CTRL_4),
-		NEW_PAD_CTRL(MX51_PAD_NANDF_RB3__FEC_RX_CLK, MX51_PAD_CTRL_4),
-		MX51_PAD_EIM_CS5__FEC_CRS,
-		MX51_PAD_EIM_CS4__FEC_RX_ER,
-		NEW_PAD_CTRL(MX51_PAD_NANDF_D11__FEC_RX_DV, MX51_PAD_CTRL_4),
-	};
-
-	imx_iomux_v3_setup_multiple_pads(fec_pads, ARRAY_SIZE(fec_pads));
-}
-
-struct fsl_esdhc_cfg esdhc_cfg[1] = {
-	{MMC_SDHC1_BASE_ADDR},
-};
-
-int get_mmc_getcd(u8 *cd, struct mmc *mmc)
-{
-	struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
-
-	if (cfg->esdhc_base == MMC_SDHC1_BASE_ADDR)
-		*cd = gpio_get_value(IMX_GPIO_NR(1, 0));
-	else
-		*cd = 0;
-
-	return 0;
-}
-
-#ifdef CONFIG_FSL_ESDHC
-int board_mmc_init(bd_t *bis)
-{
-	static const iomux_v3_cfg_t sd1_pads[] = {
-		NEW_PAD_CTRL(MX51_PAD_SD1_CMD__SD1_CMD, PAD_CTL_DSE_MAX |
-			PAD_CTL_HYS | PAD_CTL_PUS_47K_UP | PAD_CTL_SRE_FAST),
-		NEW_PAD_CTRL(MX51_PAD_SD1_CLK__SD1_CLK, PAD_CTL_DSE_MAX |
-			PAD_CTL_PUS_47K_UP | PAD_CTL_SRE_FAST),
-		NEW_PAD_CTRL(MX51_PAD_SD1_DATA0__SD1_DATA0, PAD_CTL_DSE_MAX |
-			PAD_CTL_HYS | PAD_CTL_PUS_47K_UP | PAD_CTL_SRE_FAST),
-		NEW_PAD_CTRL(MX51_PAD_SD1_DATA1__SD1_DATA1, PAD_CTL_DSE_MAX |
-			PAD_CTL_HYS | PAD_CTL_PUS_47K_UP | PAD_CTL_SRE_FAST),
-		NEW_PAD_CTRL(MX51_PAD_SD1_DATA2__SD1_DATA2, PAD_CTL_DSE_MAX |
-			PAD_CTL_HYS | PAD_CTL_PUS_47K_UP | PAD_CTL_SRE_FAST),
-		NEW_PAD_CTRL(MX51_PAD_SD1_DATA3__SD1_DATA3, PAD_CTL_DSE_MAX |
-			PAD_CTL_HYS | PAD_CTL_PUS_100K_DOWN | PAD_CTL_SRE_FAST),
-		NEW_PAD_CTRL(MX51_PAD_GPIO1_0__SD1_CD, PAD_CTL_HYS),
-		NEW_PAD_CTRL(MX51_PAD_GPIO1_1__SD1_WP, PAD_CTL_HYS),
-	};
-
-	imx_iomux_v3_setup_multiple_pads(sd1_pads, ARRAY_SIZE(sd1_pads));
-
-	esdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK);
-	return fsl_esdhc_initialize(bis, &esdhc_cfg[0]);
-}
-#endif
-
-void lcd_enable(void)
-{
-	static const iomux_v3_cfg_t lcd_pads[] = {
-		MX51_PAD_DI1_PIN2__DI1_PIN2,
-		MX51_PAD_DI1_PIN3__DI1_PIN3,
-	};
-
-	int ret;
-
-	imx_iomux_v3_setup_multiple_pads(lcd_pads, ARRAY_SIZE(lcd_pads));
-
-	gpio_set_value(IMX_GPIO_NR(1, 2), 1);
-	imx_iomux_v3_setup_pad(NEW_PAD_CTRL(MX51_PAD_GPIO1_2__GPIO1_2,
-						NO_PAD_CTRL));
-
-	ret = ipuv3_fb_init(&nec_nl6448bc26_09c, 0, IPU_PIX_FMT_RGB666);
-	if (ret)
-		puts("LCD cannot be configured\n");
-}
-
-int board_early_init_f(void)
-{
-
-
-	init_drive_strength();
-
-	/* Setup debug led */
-	gpio_direction_output(IMX_GPIO_NR(1, 6), 0);
-	imx_iomux_v3_setup_pad(NEW_PAD_CTRL(MX51_PAD_GPIO1_6__GPIO1_6,
-					PAD_CTL_DSE_MAX | PAD_CTL_SRE_FAST));
-
-	/* wait a little while to give the pll time to settle */
-	sdelay(100000);
-
-	setup_weim();
-	setup_uart();
-	setup_fec();
-	setup_gpios();
-
-	spi_io_init();
-
-	return 0;
-}
-
-static void backlight(int on)
-{
-	if (on) {
-		gpio_set_value(IMX_GPIO_NR(3, 1), 1);
-		udelay(10000);
-		gpio_set_value(IMX_GPIO_NR(3, 4), 1);
-	} else {
-		gpio_set_value(IMX_GPIO_NR(3, 1), 0);
-		gpio_set_value(IMX_GPIO_NR(3, 4), 0);
-	}
-}
-
-int board_init(void)
-{
-	/* address of boot parameters */
-	gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100;
-
-	lcd_enable();
-
-	backlight(1);
-
-	return 0;
-}
-
-int board_late_init(void)
-{
-	power_init_mx51();
-
-	reset_peripherals(1);
-	udelay(2000);
-	reset_peripherals(0);
-	udelay(2000);
-
-	/* Early revisions require a second reset */
-#ifdef CONFIG_VISION2_HW_1_0
-	reset_peripherals(1);
-	udelay(2000);
-	reset_peripherals(0);
-	udelay(2000);
-#endif
-
-	return 0;
-}
-
-/*
- * Do not overwrite the console
- * Use always serial for U-Boot console
- */
-int overwrite_console(void)
-{
-	return 1;
-}
-
-int checkboard(void)
-{
-	puts("Board: TTControl Vision II CPU V\n");
-
-	return 0;
-}
-
-int do_vision_lcd(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
-{
-	int on;
-
-	if (argc < 2)
-		return cmd_usage(cmdtp);
-
-	on = (strcmp(argv[1], "on") == 0);
-	backlight(on);
-
-	return 0;
-}
-
-U_BOOT_CMD(
-	lcdbl, CONFIG_SYS_MAXARGS, 1, do_vision_lcd,
-	"Vision2 Backlight",
-	"lcdbl [on|off]\n"
-);