summaryrefslogtreecommitdiff
path: root/board/spear/x600
diff options
context:
space:
mode:
authorStefan Roese <sr@denx.de>2016-04-27 09:10:42 +0200
committerStefan Roese <sr@denx.de>2016-05-31 07:48:34 +0200
commitf7c32e8ece7fefd950382a7522aff9939a218b91 (patch)
tree11038d40da9febc6223d1663b5bf0812290a779f /board/spear/x600
parent452b3813f99538ebd54407e911733c4b26efd1a4 (diff)
downloadu-boot-imx-f7c32e8ece7fefd950382a7522aff9939a218b91.zip
u-boot-imx-f7c32e8ece7fefd950382a7522aff9939a218b91.tar.gz
u-boot-imx-f7c32e8ece7fefd950382a7522aff9939a218b91.tar.bz2
arm: spear: x600: Add support for Micrel KSZ9031 PHY
As the old ethernet PHY is not available any more, the x600 board has been redesigned with the Micrel KSZ9031 PHY. This patch adds support to autodetect the PHY and configure the Micrel PHY correctly. Signed-off-by: Stefan Roese <sr@denx.de>
Diffstat (limited to 'board/spear/x600')
-rw-r--r--board/spear/x600/x600.c80
1 files changed, 59 insertions, 21 deletions
diff --git a/board/spear/x600/x600.c b/board/spear/x600/x600.c
index b8edfcd..f8e9fdd 100644
--- a/board/spear/x600/x600.c
+++ b/board/spear/x600/x600.c
@@ -8,6 +8,7 @@
*/
#include <common.h>
+#include <micrel.h>
#include <nand.h>
#include <netdev.h>
#include <phy.h>
@@ -69,27 +70,64 @@ void board_nand_init(void)
int board_phy_config(struct phy_device *phydev)
{
- /* Extended PHY control 1, select GMII */
- phy_write(phydev, MDIO_DEVAD_NONE, 23, 0x0020);
-
- /* Software reset necessary after GMII mode selction */
- phy_reset(phydev);
-
- /* Enable extended page register access */
- phy_write(phydev, MDIO_DEVAD_NONE, 31, 0x0001);
-
- /* 17e: Enhanced LED behavior, needs to be written twice */
- phy_write(phydev, MDIO_DEVAD_NONE, 17, 0x09ff);
- phy_write(phydev, MDIO_DEVAD_NONE, 17, 0x09ff);
-
- /* 16e: Enhanced LED method select */
- phy_write(phydev, MDIO_DEVAD_NONE, 16, 0xe0ea);
-
- /* Disable extended page register access */
- phy_write(phydev, MDIO_DEVAD_NONE, 31, 0x0000);
-
- /* Enable clock output pin */
- phy_write(phydev, MDIO_DEVAD_NONE, 18, 0x0049);
+ unsigned short id1, id2;
+
+ /* check whether KSZ9031 or AR8035 has to be configured */
+ id1 = phy_read(phydev, MDIO_DEVAD_NONE, 2);
+ id2 = phy_read(phydev, MDIO_DEVAD_NONE, 3);
+
+ if ((id1 == 0x22) && ((id2 & 0xFFF0) == 0x1620)) {
+ /* PHY configuration for Micrel KSZ9031 */
+ printf("PHY KSZ9031 detected - ");
+
+ phy_write(phydev, MDIO_DEVAD_NONE, MII_CTRL1000, 0x1c00);
+
+ /* control data pad skew - devaddr = 0x02, register = 0x04 */
+ ksz9031_phy_extended_write(phydev, 0x02,
+ MII_KSZ9031_EXT_RGMII_CTRL_SIG_SKEW,
+ MII_KSZ9031_MOD_DATA_NO_POST_INC,
+ 0x0000);
+ /* rx data pad skew - devaddr = 0x02, register = 0x05 */
+ ksz9031_phy_extended_write(phydev, 0x02,
+ MII_KSZ9031_EXT_RGMII_RX_DATA_SKEW,
+ MII_KSZ9031_MOD_DATA_NO_POST_INC,
+ 0x0000);
+ /* tx data pad skew - devaddr = 0x02, register = 0x05 */
+ ksz9031_phy_extended_write(phydev, 0x02,
+ MII_KSZ9031_EXT_RGMII_TX_DATA_SKEW,
+ MII_KSZ9031_MOD_DATA_NO_POST_INC,
+ 0x0000);
+ /* gtx and rx clock pad skew - devaddr = 0x02, reg = 0x08 */
+ ksz9031_phy_extended_write(phydev, 0x02,
+ MII_KSZ9031_EXT_RGMII_CLOCK_SKEW,
+ MII_KSZ9031_MOD_DATA_NO_POST_INC,
+ 0x03FF);
+ } else {
+ /* PHY configuration for Vitesse VSC8641 */
+ printf("PHY VSC8641 detected - ");
+
+ /* Extended PHY control 1, select GMII */
+ phy_write(phydev, MDIO_DEVAD_NONE, 23, 0x0020);
+
+ /* Software reset necessary after GMII mode selction */
+ phy_reset(phydev);
+
+ /* Enable extended page register access */
+ phy_write(phydev, MDIO_DEVAD_NONE, 31, 0x0001);
+
+ /* 17e: Enhanced LED behavior, needs to be written twice */
+ phy_write(phydev, MDIO_DEVAD_NONE, 17, 0x09ff);
+ phy_write(phydev, MDIO_DEVAD_NONE, 17, 0x09ff);
+
+ /* 16e: Enhanced LED method select */
+ phy_write(phydev, MDIO_DEVAD_NONE, 16, 0xe0ea);
+
+ /* Disable extended page register access */
+ phy_write(phydev, MDIO_DEVAD_NONE, 31, 0x0000);
+
+ /* Enable clock output pin */
+ phy_write(phydev, MDIO_DEVAD_NONE, 18, 0x0049);
+ }
if (phydev->drv->config)
phydev->drv->config(phydev);